共查询到20条相似文献,搜索用时 138 毫秒
1.
2.
《工程力学》2010,(8)
采用数字散斑相关量测方法(DSCM)和数字照相量测软件系统PhotoInfor,通过观测表面位移场、应变场及总体变形在整个加载过程中的变化特点,对大小为100mm×100mm×100mm的含有孔洞的岩石试件在单轴压缩下的变形破裂演变规律进行了实验研究。结果表明:1)DSCM方法能够对岩石变形破裂的特点进行全程有效捕捉,有助于加深对岩石变形局部化过程的全面认识;2)含孔洞岩石试件局部化变形起始于峰值点处轴向位移的80%处,应力峰值点附近变形局部化最为剧烈;3)岩石表面平均最大剪应变随轴向位移的变化曲线,总体上能够很好地反映岩石变形破裂的演变过程和规律,可作为分析岩石变形演变的一个参考特征参数。 相似文献
3.
4.
5.
为提高轻量化复合装甲的抗侵彻能力,提出了内部填充陶瓷棒并由混杂短切玻璃纤维的环氧树脂封装的点阵金属夹层防护结构。首先,通过弹道冲击实验研究了陶瓷棒填充点阵金属夹层防护结构的抗弹丸侵彻能力;然后,结合失效模式和吸能效率,综合分析了该夹层防护结构的抗侵彻机制。结果表明:陶瓷棒填充点阵金属夹层防护结构的主要失效模式包括点阵金属结构和混杂填充材料的拉伸断裂、陶瓷棒的破裂、面板和背板的局部剪切破坏以及背板的总体弯曲变形。在球形弹丸侵彻过程中,由于点阵金属结构的塑性大变形和剪切扩孔、陶瓷棒和环氧树脂的断裂破坏以及面板的宏观弯曲变形,防护结构的抗侵彻能力得到大幅提高。研究结果可为新型轻质复合装甲的防护设计提供一定参考。 相似文献
6.
共晶Si形貌与A356铝合金的动态、准静态压缩变形下的力学性能及抗氢脆性能的影响密切相关。因此文章通过Material Test System (MTS)及霍普金森压杆(SHPB)测试变质前后A356铝合金的动态/准静态压缩力学行为,并采用电化学充氢方法研究合金的抗氢脆性能。结果表明,准静态压缩变形后,合金中板状共晶Si垂直于压缩方向破裂成颗粒状。细化后的共晶Si提高了合金的塑性,延缓了合金的失效。而动态压缩变形后,板状共晶Si变形不均匀,并且碎成块状的共晶Si的尖端在压缩过程中会切割基体,导致其附近出现裂纹等缺陷。随着应变速率增大,铸态A356合金的屈服强度及抗压强度逐渐增大,合金具有一定的应变速率敏感性。变质后,共晶Si得到细化,增大了Al/Si接触面积,共晶Si捕获原子氢后降低了其与基体的连结,导致合金在拉伸变形过程中裂纹更易沿其扩展,并且细化后的共晶Si会进一步降低合金的抗氢脆性能力。其中细化后残存的块状共晶Si在捕获原子氢后会出现脱粘现象,易成为裂纹萌发点。 相似文献
7.
8.
9.
《工程力学》2010,(12)
基于注浆锚固裂隙砂岩单轴压缩试验结果,研究了不同锚固作用下裂隙砂岩破裂模式,探讨了锚杆根数以及预应力对裂隙砂岩破裂特征的影响,分析了含两根锚杆裂隙砂岩变形破坏过程中裂纹萌生、扩展和演化规律。结果表明:随着锚杆根数增加,裂隙砂岩最终宏观破裂模式趋于复杂,对30°裂隙倾角而言,试样逐渐由拉伸破裂过渡到拉剪混合破裂模式;而对45°裂隙倾角而言,试样逐渐由剪切破裂过渡到拉剪混合破裂模式。预应力抑制了裂隙岩样中拉伸裂纹的扩展和延伸,使得呈现的裂纹数显著少于无预应力条件下试样的裂纹数。最后以典型锚固裂隙砂岩试样为例,分析了变形破坏全过程中裂纹扩展特征。注浆锚固裂隙砂岩具有显著渐近破裂特点。 相似文献
10.
含共面裂隙群砂岩强度与破裂特征的试验研究 总被引:1,自引:0,他引:1
节理岩体力学行为是地下工程稳定分析及支护设计的基础。采用岩石力学伺服试验机对含充填共面裂隙群砂岩试样进行单轴加载试验,分析了连通率和充填方式对砂岩强度及变形破裂特征的影响规律。试验结果表明:裂隙砂岩的力学性能较完整砂岩呈现出显著的劣化,且随着裂隙连通率的增大,峰值强度、峰值应变及弹性模量均逐渐减小;试样破裂过程中预制裂隙尖端先后出现Ⅰ类张拉裂纹和Ⅱ类剪切裂纹,但最终的失稳破裂面由II类裂纹扩展形成,Ⅰ类裂纹和Ⅱ类裂纹与预制裂隙的夹角随着裂隙连通率的增大逐渐增大;受充填方式的影响,裂隙砂岩的强度及变形特征均呈现出显著增大的趋势,而弹性模量提升幅度相对较小。 相似文献
11.
介绍了国内外金属材料焊缝维氏硬度试验标准体系的最新进展,对比分析了我国现行金属材料焊缝维氏硬度试验标准体系中存在的不足.与国际标准相比,我国现行部分金属材料焊缝维氏硬度试验标准标龄较长,需加快修订.此外,要加强标准间相互引用,实现标准之间的方法统一. 相似文献
12.
LED照明产品的广泛应用和技术的迅猛发展,给LED照明产业标准化研究带来了新的机遇与挑战。本文从技术要求(包括:光通量维持率及寿命、初始光效、显色性)和测试方法(光衰测试方法)的角度对2008~2010年间我国发布的一些代表性国家、行业和地方道路照明用LED灯具标准进行了对比分析,得出如下结论:1)我国各地道路照明用LED灯具标准存在显著差异,急需统一的道路照明用LED灯具标准来有效规范整个行业的发展;2)LED照明技术的不断革新和进步推动着LED照明相关标准的不断更新和改进,已经有并即将有更多符合产业发展要求的标准被逐步推出。可以预见的是,道路照明用LED灯具标准将朝着统一规范化、细致化、全面化的方向发展。鉴于我国道路照明用LED灯具市场的特殊情况,该项标准的制定甚至可能优先于国际标准。 相似文献
13.
李和平 《理化检验(物理分册)》2021,57(1):1-4
以碳素结构钢、合金结构钢、轴承钢、弹簧钢和冷作模具钢为例,将国标与美国ASTM标准和日本JIS标准对金相检验项目的要求进行了对比和分析.结果表明:国标对于金相检验项目的要求是最多的;ASTM标准对金相检验项目的要求较少但是具有针对性;JIS标准对金相检验项目的要求弹性较大,主要由买方与制造方协议规定.对比国外标准对应钢... 相似文献
14.
15.
An end-point quantitative nucleic acid sequence-based amplification (NASBA) reaction with two exogenous internal standards for the detection of the model analyte E. coli clpB mRNA was developed and statistically analyzed. Electrochemiluminescence was chosen as a highly sensitive detection means allowing careful evaluation of the internal standards used. The two internal standards examined had been designed previously using a novel and rapid NASBA-based method. Initially, each standard was used separately in a NASBA reaction; subsequently, two internal standards were added into one reaction at different concentrations. The accuracy and precision of the data obtained were analyzed using linear and multiple regression analysis. In the case of single-standard reactions, the accuracy was >95% and the precision >98.5%. In the case of double-standard reactions, the accuracy increased to >97%. With a single internal standard, 3 orders of magnitude of target sequence could be quantified; using three different concentrations of one internal standard, the dynamic range increased to 5 orders of magnitude. In both cases, a detection limit as low as 0.14 pg of target sequence was obtained. In the case of double-internal standard reactions, a dynamic range with 5 orders of magnitude and a detection limit of 1.76 pg was determined. The high-performance quality of the internal standards was assumed to be in part due to the unique synthesis process using two NASBA reactions rather than traditional cloning techniques. 相似文献
16.
D. T. Burns M. O’Brien P. Lamperti M. Boutillon 《Journal of research of the National Institute of Standards and Technology》2003,108(5):383-389
The air-kerma standards used for the measurement of medium-energy x rays were compared at the National Institute of Standards and Technology (NIST) and at the Bureau International des Poids et Mesures (BIPM). The comparison involved a series of measurements at the BIPM and the NIST using the air-kerma standards and two NIST reference-class transfer ionization standards. Reference beam qualities in the range from 60 kV to 300 kV were used. The results show the standards to be in agreement within the combined standard uncertainty of the comparison of 0.35 %. 相似文献
17.
标准支撑经济社会健康发展的作用显著提高了公众对标准问题的关注和标准与产品质量相关性的探索意愿.但受标准技术性和专业性的影响,其对一般公众而言知识的可及性相对较差,因此可能导致标准有关信息的引入对公众的产品认知与其他外部信息的影响有不同的发展规律.本文以标准作为兼具技术性和公众相关性话题的代表,通过实验分析的方法,观察不同信息叠加对公众的产品态度的影响,讨论了标准对产品质量认知的影响方式. 相似文献
18.
标准制定过程是一个创作过程,标准构成《著作权法》规定的"作品",应受《著作权法》的保护.众多标准起草人是标准版权的共同所有人,标准制定组织通过约定成为标准版权的实际权利人.本文通过理论分析标准版权保护的法理基础,比较分析域外标准版权政策,提出我国国家标准版权保护的若干政策建议,希望对我国良好标准化治理体制的建立与完善有所裨益. 相似文献
19.
《IEEE transactions on instrumentation and measurement》1984,33(3):155-159
The artifact standard, an object which embodies the physical quantity to be standardized, has served the metrology community well. Its great merits are its stability and the precision with which it can be compared to other like artifacts. Its use as the basis of a measurement system is not without drawbacks however. Among these are: its definition may be arbitrary, it is maintained by a national or international standardizing laboratory and is not accessible to the user, and it is subject to loss or damage through accident, sabotage, or act of war. An extension of the NBS Volt Transfer Program is capable of providing what may be termed a "Distributed Artifact Standard" of dc voltage. Such a standard will maintain the value of the volt in the universe of artifact standards maintained by the standards laboratories of the measurement community. This standard has none of the objectionable properties cited. It is accessible, it is immune to loss or damage, and it can be certified in terms of the absolute standards maintained by the national standards institutes. The theoretical and empirical basis for such a distributed artifact standard is presented. 相似文献