共查询到17条相似文献,搜索用时 140 毫秒
1.
利用ANSYS和MXTLAB软件,对缩放型片材机头中熔体的速度、压力和剪切应力的分布进行三维有限元模拟和分析。通过对机头流道不同截面处熔体场量分布的模拟,探知了熔体在流道内的运动规律及特点。 相似文献
2.
3.
4.
5.
为提高管材挤出机头的加工性能,加强机头流道的塑化作用,以挤出机头中直通式管材挤出机头作为研究对象,建立其挤出加工过程的数学模型,利用ANSYS Fluent软件对管材挤出机头流道的流动过程进行模拟研究,用CFD-post对模拟结果进行分析,并根据模拟结果对管材挤出机头流道的结构进行优化设计。模拟结果表明:优化后的管材挤出机头流道增加了熔体的流动速度,减少了熔体在机头流道内的停留时间,提高了流动性能;并降低了压缩段末端的压力降,提高了成型段上的压力降,增强了熔体的塑化性能,使制品变得更加紧密。 相似文献
6.
7.
利用有限元软件包Polyflow模拟不同条件下发泡机头流道内PS/CO2熔体的流动,获得了压力,计算出压降速率,并分析熔体温度、CO2含量、机头模口流道直径和质量流率对流道内压力和压降速率的影响。结果表明,在加工条件允许的范围内,降低熔体温度,可以显著提高机头流道中的压力和机头模口流道中的压降速率;当熔体温度一定时,机头流道中的压力和机头模口流道中的压降速率随着CO2含量的增加而降低。尤其当熔体温度为150℃,CO2质量含量由1%增加到2%时,机头模口流道中的压降速率急剧降低;减小机头模口流道直径可有效地提高机头流道内的压力和压降速率。熔体温度175℃,CO2质量含量5%、质量流率1kg/h时,模口直径由1mm减小到0.5mm,机头入口段压力由5.9MPa增大到近30MPa。 相似文献
8.
9.
在分析了塑料熔体经过机头流道的流动过程与流变学特性基础上,将机头流道压缩段的过渡形状设计为直线型和圆弧型。利用Ployfow软件对直线型和圆弧型过渡压缩段的机头流道进行数值模拟,分析不同压缩段过渡形状对流道压力场、速度场和剪切速率场的影响。结果表明,流道压缩段过渡形状设计为圆弧型后,增大了熔体在成型段内的压力降、流动速度几流道出口速度均匀性,提高了管材的密实度、壁厚均匀性和力学强度,减少了熔体在流道内的停留时间。改进后的流道成型段最大壁面剪切速率从99.6 s-1降低至76.3 s-1,远低于硬质聚氯乙烯(PVC-U)管材表面出现鲨鱼皮现象的临界剪切速率,流道出口壁面剪切速率均匀性与管材表面质量均得到显著提高。 相似文献
10.
采用Hele-Shaw模型对共挤出机头流道内的聚合物熔体流动进行了数值模拟分析,计算得到了衣架型机头出口处各层料流分界面的位置,并讨论了物料特性、进口处流率比对机头出口处分界面位置的影响。 相似文献
11.
The flow kinematics of power-law fluids in fishtail dies is studied. A general isothermal three-dimensional finite element code developed by the authors is used for the flow analysis purpose. The basic geometry of the fishtail die is defined by simple super-elliptical curves, which allows a smooth transition from a circle to a slit. The three-dimensional path line and the residence time distribution (RTD) are calculated from the velocity field obtained from the finite element solution of the conservation equations. The effects of the rheological properties and the die geometry on the path line pattern and the residence time distribution are investigated. The results indicate that as both the length of the transition zone and the fishtail angle increases, the residence time distribution becomes more uniform. However, the power-law index does not affect the residence time distribution significantly. 相似文献
12.
13.
14.
15.
Thierry G. Charbonneaux 《Polymer-Plastics Technology and Engineering》2013,52(7):665-684
The various die designs that have been proposed for the manufacture of sheets and flat films from polymeric materials are reviewed, along with the corresponding flow analysis and derived design equations. Successively, the T-die, the linearly tapered coat-hanger die, the curvilinearly tapered coat-hanger die (with manifold of circular or rectangular cross-section), and the fishtail die are examined. In each case, care is taken to outline the assumptions used to derive the equations, and to state the advantages and disadvantages of each design. The limits of these mentioned assumptions are explained and illustrated. Particular attention is paid to the aspects of the design which affect the processing of sensitive or reactive materials (i.e., residence time distribution and wall shear stress). 相似文献
16.
逆向挤出在木塑异型材挤出口模设计中的应用 总被引:5,自引:0,他引:5
介绍了POLYFLOW模拟软件的结构、特点及其在聚合物加工过程中的应用,以工字型木塑异型材挤出口模设计为例,建立了数学模型、几何模型及有限元模型,并进行了数值模拟和分析,详细论述了如何有效应用POLYFLOW逆向挤出功能对木塑复合异型材挤出口模进行设计。 相似文献
17.
本文对拉挤成型过程中热传导方程和固化度动力学方程进行了数值分析,确定了拉挤模具内温度和固化度属于强耦合关系。使用有限元软件IFEPG和FORTRAN语言为平台开发出一计算机程序,并使用该程序模拟出在一定工艺参数下拉挤模具内温度和固化度的分布,着重探讨了拉挤速度对模具内温度和固化度分布的影响。 相似文献