Constrained Densification of Alumina/Zirconia Hybrid Laminates, I: Experimental Observations of Processing Defects

Various forms of damage were observed in pressure-less-sintered Al₂O₃/ZrO₂symmetric laminates and asymmetric laminates (bilayers) fabricated by tape casting and lamination. These defects included channel cracks in the ZrO₂ layers, Al₂O₃ edge-effect cracks parallel to the layers, delamination in the Al₂O₃layers, and debonding between the Al₂O₃and ZrO₂layers. Based on detailed microscopic observations, the defects were attributed to sintering rate and thermal expansion mismatch between the layers. Cracks or cracklike defects were formed in the early stages of densification, and these cracks either opened during sintering or acted as preexisting flaws for thermal expansion mismatch cracks. Consequently, the extent of cracking could be reduced or even eliminated by decreasing mismatch stresses during the sintering and cooling stages. This can be accomplished by reducing the heating and/or cooling rates or by adding Al₂O₃in the ZrO₂layers. The sintering mismatch stresses were estimated from the degree of curling in asymmetric laminates and from layer viscosities that were obtained by cyclic loading dilatometry. The measured curvature was an indication of the mismatch in sintering strain between Al₂O₃and ZrO₂and were consistent with the dilatometric data that were obtained for the component layers.     

Effect of Annealing Environment on the Crack Healing and Mechanical Behavior of Silicon Carbide-Reinforced Alumina Nanocomposites

The crack healing and strength behavior of an alumina-silicon carbide (Al₂O₃-SiC) nanocomposite (Al₂O₃+ 5 vol% 0.2 μm SiC particles) has been studied, as a function of the crack size and the annealing environment. Results show that annealing treatments can significantly increase the indentation strength. The annealing atmosphere has a profound influence on the extent of crack healing and the degree of strength recovery. Annealing in argon results in a strength increase of 50%, whereas annealing in air yields a three-fold improvement in the indentation strength. Scanning electron microscopic observation has shown that healing of indentation cracks occurs in both environments, with the greater degree of healing occurring during annealing in air. Implications of the findings to the strengthening mechanism in Al₂O₃ (SiC) nanocomposites will be discussed.     

Electric-Field-Induced Crack Growth Behavior in PZT/Al2O3 Composites

Hard lead zirconate titanate (PZT) and PZT/Al₂O₃ composites were prepared and the alternating-electric-field-induced crack growth behavior of a precrack above the coercive field was evaluated via optical and scanning electron microscopy. The crack extension in the 1.0 vol% Al₂O₃ composite was significantly smaller than that in monolithic PZT and the 0.5 vol% Al₂O₃ composite. Secondary-phase Al₂O₃ dispersoids were found both at grain boundaries and within grains in the composites. A large number of dispersoids were observed at the grain boundaries in the 1.0 vol% Al₂O₃ composite. It appears that the Al₂O₃ dispersoids reinforce the grain boundaries of the PZT matrix as well as act as effective pins against microcrack propagation.     

Thermal Shock Resistance of Sintered Alumina/Silicon Carbide Nanocomposites Evaluated by Indentation Techniques

The thermal shock resistance of sintered Al₂O₃/1, 2.5, and 5 vol% SiC nanocomposites was studied using two indentation techniques. In the first technique, "indentation thermal shock" measurements were made of the extension of median/radial cracks around Vickers indentations after quenching from various temperatures (up to 480°C) into a bath of boiling water. This technique allowed a critical thermal shock temperature, Δ T _C^Ind, to be quantitatively evaluated. In the second technique, "indentation fatigue" tests were conducted on the thermally shocked specimens; repeated indentations were made at the same site, and the number of load cycles needed to initiate lateral fracture was measured. The results showed that nanocomposites with an addition of SiC nanophase as low as 1 vol% had a thermal shock resistance superior to that of pure Al₂O₃.     

Evidence for Bulk Residual Stress Strengthening in Al2O3/SiC Nanocomposites

The fracture behavior of Al₂O₃/SiC nanocomposites has been studied as a function of the SiC volume fraction and compared to that of the pure Al₂O₃ matrix. A pronounced strengthening effect was only observed for materials with low SiC content (i.e., ≤10 vol%) although no evidence of concurrent toughening was found. Assessment of near-tip crack opening displacement (COD) could not experimentally substantiate significant occurrence of an elastic crack-bridging mechanism, in contrast with a recently proposed literature model. Quantitative fractography analysis indicated that transgranular crack propagation in Al₂O₃/SiC nanocomposites depends on the location of the SiC dispersoids within the matrix texture; the higher the fraction of transgranularly located dispersoids, the more transgranular the fracture mode. Experimental evidence of remarkably high residual stresses arising from thermal dilatation mismatch (upon cooling) between Al₂O₃ and SiC phases were obtained by fluorescence and Raman spectroscopy. A strengthening mechanism is invoked which merely arises from residual stress through strengthening of Al₂O₃ grain boundaries.     

Measurement of Microscopic Bridging Stresses in an Alumina/Molybdenum Composite by In Situ Fluorescence Spectroscopy

The R -curve behavior of an Al₂O₃ ceramic with 25 vol% of molybdenum-metal particles added was studied by using fracture-mechanics experiments and in situ piezospectroscopic measurements of microscopic bridging tractions. Cracks were propagated by using a crack stabilizer, which allowed stable crack growth in a bending geometry. Microscopic bridging stresses were measured in situ during fracture propagation by detecting the shift of the Cr³⁺ fluorescence lines of Al₂O₃. Laser spots ∼1 µm in diameter and ∼10 µm deep were focused at the ceramic/metal interface of the bridging sites, and the closure stresses that acted on the crack faces were recorded as a function of external load. The maximum stress that was experienced by the stretched metal particles prior to final failure was ∼0.4 GPa. The maximum stress magnitude was not markedly different in relatively small (i.e., <5 µm) metal particles, failing with large ductility, as compared with larger particles which, instead, fractured in semibrittle fashion. A map of bridging tractions along the crack wake was constructed under a constant stress intensity factor, almost equal to that which is critical for crack propagation. Using this map to theoretically predict the rising R -curve behavior of the composite led to results that were consistent with the fracture-mechanics experiments, thus enabling us to explain the observed toughening, primarily in terms of a crack-bridging mechanism.     

Neutron Diffraction Measurements of the Residual Stresses in Al2O3-ZrO2 (CeO2) Ceramic Composites

High-resolution neutron powder diffraction was used to study the residual stresses in Al₂O₃-ZrO₂ (12 mol% CeO₂) ceramic composites containing 10, 20, and 40 vol% ZrO₂ (CeO₂). The diffraction data were analyzed using the Rietveld structure refinement technique. The analysis shows that for all samples, the CeO₂-stabilized tetragonal ZrO₂ particles are in tension and the Al₂O₃ matrix is in compression. For both the ZrO₂ particles and the Al₂O₃ matrix, the average lattice strains are anisotropic and increase approximately linearly with a decrease in the corresponding phase content. It is shown that these features can be qualitatively understood by taking into consideration the thermal expansion mismatch between the ZrO₂ and Al₂O₃ grains. Also, for all composite samples, the diffraction peaks are broader than the instrumental resolution, indicating that the strains in these samples are inhomogeneous. From an analysis of the refined peak shape parameters, the average root-meansquare strain, which describes the distribution of the inhomogeneous strain field, was determined. Finally, the average residual stresses were evaluated from the experimentally determined average lattice strains and compared with recent results of X-ray measurements on similar composites.     

Mechanical Behavior of Alumina–Silicon Carbide „Nanocomposites”

The fracture behavior of Al₂O₃ containing 5 vol% 0.15μm SiC particles was investigated using indentation techniques. A significant increase in strength was achieved by the addition of SiC particles to the base Al₂O₃. Specifically, the strength increased from 560 MPa for Al₂O₃ to 760 MPa for the composite samples (average values for unindented hotpressed bars tested in four-point bending). After annealing for 2 h at 1300°C, the average strength of the composite samples increased to about 1000 MPa. Toughness was estimated using indentation-strength data. While there was a slight increase in toughness, the increase was not sufficient to account for the increase in the unindented strength on SiC particle addition. It is suggested that the observed strengthening and apparent toughening were due to a machining-induced compressive surface stress.     

Reaction Processing of Al2O3 Composites Containing Iron and Iron Aluminides

Different Fe-Al₂O₃ and FeAl-Al₂O₃ composites with metallic contents up to 30 vol% have been fabricated via reaction processing of Al₂O₃, Fe, and Al mixtures. Low Al contents (<∼10 vol%) within the starting mixture lead to composites consisting of Fe embedded in an Al₂O₃ matrix, whereas aluminide-containing Al₂O₃ composites result from powder mixtures with higher Al contents. In both cases, densification up to 98% TD can be achieved by pressureless sintering in inert atmosphere at moderate temperatures (1450°-1500°C). The proposed reaction sintering mechanism includes the reduction of native oxide layers on the surface of the Fe particles by Al and, in the case of mixtures with high Al contents, aluminide formation followed by sintering of the composites. Density and bending strengths of the reaction-sintered composites depend strongly on the Al content of the starting mixture. In the case of samples containing elemental Fe, crack path observations indicate the potential for an increase of fracture toughness, even at room temperature, by crack bridging of the ductile Fe inclusions.     

Optimization of a Nanoparticle Suspension for Freeze Casting

Poly(acrylic acid) (PAA) dispersant concentration, suspension pH, and Al₂O₃ solids loading effects on PAA adsorption onto Al₂O₃ nanoparticles were studied; the stability and rheology of the Al₂O₃ nanoparticle suspensions were examined. The most desirable suspension conditions were 7.5–9.5 for pH and 2.00–2.25 wt% of Al₂O₃ for the PAA concentration. Electrical double-layer thickness and PAA adsorption layer thickness comparison showed that electrosteric stabilization was dominant. 45.0 vol% Al₂O₃ solids loading can be achieved for freeze casting. The maximum solids loading was predicted to be 50.7 vol%. The freeze-cast sample showed that pre-rest before freezing was critical for achieving desirable microstructures.     

Densification and Mechanical Properties of B4C with Al2O3 as a Sintering Aid

The densification behavior and mechanical properties of B₄C hot-pressed at 2000°C for 1 h with additions of Al₂O₃ up to 10 vol% were investigated. Sinterability was greatly improved by the addition of a small amount of Al₂O₃. The improvement was attributed to the enhanced mobility of elements through the Al₂O₃ near the melting temperature or a reaction product formed at the grain boundaries. As a result of this improvement in the density, mechanical properties, such as hardness, elastic modulus, strength, and fracture toughness, increased remarkably. However, when the amount of Al₂O₃ exceeded 5 vol%, the level of improvement in the mechanical properties, except for fracture toughness, was reduced presumably because of the high thermal mismatch between B₄C and Al₂O₃.     

Crack Bifurcation in Laminar Ceramic Composites

Crack bifurcation was observed in laminar ceramic composites when cracks entered thin Al₂O₃ layers sandwiched between thicker layers of Zr(12Ce)O₂. The Al₂O₃ layers contained a biaxial, residual, compressive stress of ∼2 GPa developed due to differential contraction upon cooling from the processing temperature. The Zr(12Ce)O₂ layers were nearly free of residual, tensile stresses because they were much thicker than the Al₂O₃ layers. The ceramic composites were fabricated by a green tape and codensification method. Different specimens were fabricated to examine the effect of the thickness of the Al₂O₃ layer on the bifurcation phenomena. Bar specimens were fractured in four-point bending. When the propagating crack encountered the Al₂O₃ layer, it bifurcated as it approached the Zr(12Ce)O₂/ Al₂O₃ interface. After the crack bifurcated, it continued to propagate close to the center line of the Al₂O₃ layer. Fracture of the laminate continued after the primary crack reinitiated to propagate through the next Zr(12Ce)O₂ layer, where it bifurcated again as it entered the next Al₂O₃ layer. If the loading was stopped during bifurcation, the specimen could be unloaded prior to complete fracture. Although the residual stresses were nearly identical in all Al₂O₃ layers, crack bifurcation was observed only when the layer thickness was greater than ∼70 μm.     

Tribological Properties of Polycrystalline Ti3SiC2 and Al2O3-Reinforced Ti3SiC2 Composites

Tribological properties of Ti₃SiC₂ and Al₂O₃-reinforced Ti₃SiC₂ composites (10 and 20 vol% Al₂O₃) were investigated by using an AISI-52100 bearing steel ball dryly sliding on a linear reciprocating athletic specimen. The friction coefficients were found varying only in a range of 0.1 under the applied loads (2.5, 5, and 10 N), and the wear rates of the composites decreased with increasing Al₂O₃ content. The enhanced wear resistance is mainly attributed to the hard Al₂O₃ particles nail the surrounding soft matrix and decentrale the shear stresses under the sliding ball to reduce the wear losses.     

Reinforcement of Hydroxyapatite Bioceramic by Addition of Ni3Al and Al2O3

The effects of Ni₃Al and Al₂O₃ additions on the mechanical properties of hydroxyapatite (HAp) were investigated. The addition of Ni₃Al particles increased the strength as well as the fracture toughness of HAp. However, the improvements in the properties were limited because of the formation of microcracks around the metal particles. The microcracks were formed because of the large difference in the coefficients of thermal expansion between HAp and Ni₃Al, and because of the relatively large size of Ni₃Al particles (∼20 µm). The addition of submicrometer Al₂O₃ powder was also effective in increasing the mechanical properties. The flexural strength and the fracture toughness were increased from about 100 MPa and 0.7 MPam^1/2, respectively, to 200 MPa and 1.5 MPam^1/2 by the addition of 20 vol% Al₂O₃. When Ni₃Al and Al₂O₃ were added together, the fracture toughness was further increased to 2.3 MPam^1/2. This increase in the fracture toughness was attributed to the synergistic effect of matrix strengthening and crack interactions with the metal particles.     

Crack Deflection in Ceramic/Ceramic Laminates with Strong Interfaces

Crack deflection in electrophoretically deposited Al₂O₃/ TZ-3Y (3 mol% Y₂O₃-stabilized tetragonal ZrO₂) lamellar composites with strong interfaces is described. The fracture behavior of, and crack paths in, these materials were evaluated using indentation and four-point bend tests. The effects of residual and induced stresses on crack deflection are considered.     

Dynamic Fracture Characterization of Al2O3 and SiCw/Al2O3

The dynamic stress intensity factors, which were determined with newly developed bar impact facilities and a new data reduction procedure, for an Al₂O₃ ceramic and 29 vol% SiC_w/Al₂O₃ composite were virtually identical, thus indicating that the short SiC whiskers were ineffective under dynamic fracture. SEM studies revealed five distinct fracture morphologies with increased percentage area of transgranular fracture in both materials with rapid crack propagation. Also, the high dynamic stress intensity factor caused multiple microscopic crack planes to form and then join as the crack advanced.     

Indentation of Silicate-Glass Films on Al2O3 Substrates

The deformation of thin layers of glass on crystalline materials has been examined using newly developed experimental methods for nanomechanical testing. Continuous films of anorthite (CaAl₂Si₂O₈) were deposited onto Al₂O₃ surfaces by pulsed-laser deposition. Mechanical properties such as Young's modulus and hardness were probed with a high-resolution depth-sensing indentation instrument. Nanomechanical testing, combined with AFM in situ imaging of the deformed regions, allowed force-displacement measurements and imaging of the same regions of the specimen before and immediately after indentation. This new technique eliminates any uncertainty in locating the indentation after unloading. Emphasis has been placed on examining how the Al₂O₃ substrate crystallographic orientation will affect mechanical composite response of silicate-glass film/Al₂O₃ system.     

Indentation Fracture Response and Damage Resistance of Al2O3-ZrO2 Composites Strengthened by Transformation-Induced Residual Stresses

Indentation fracture behavior of three-layer Al₂O₃-ZrO₂ composites with substantial compressive residual stresses was compared with the behaviors of monolithic Al₂O₃ and Al₂O₃-ZrO₂ ceramics without intentionally introduced residual stresses. The indentation cracks were smaller in the three-layer specimens relative to the monolithic specimens in agreement with the predictions of indentation fracture mechanics theory. Indentation and strength testing were used to show that a residual compressive stress of approximately 500 MPa exists in the outer layers of the three-layer composites. The three-layer specimens showed excellent damage resistance in that the strength differential between the three-layer and monolithic indented specimens was maintained at indentation loads up to 1000 N, the maximum indentation load used in the experiments.     

Tape Casting of Al2O3/ZrO2 Laminated Composites

Fracture toughness of ZrO₂-toughened alumina could he increased by macroscopic interfaces, such as those existing in laminated composites. In this work, tape casting was used to produce A/A or A/B laminates, where A and B can be Al₂O₃, Al₂O₃/5 vol% ZrO₂, and Al₂O₃/l0 vol% ZrO₂. An increase of toughness is observed, even in the Al₂O₃/Al₂O₃ laminates.     

Improvement of the Dispersion of Al2O3 Slurries Using EDTA-4Na

Polyacrylic acid (PAA) is known to be an effective dispersant for Al₂O₃ powder in aqueous media. However, at high solid loading (>55 vol%), the dispersion of the Al₂O₃ suspensions became difficult with only PAA as a dispersant. In this paper, ethylenediaminetetraacetic acid, tetrasodium salt, dihydrate (EDTA-4Na) was introduced to improve the dispersion of the Al₂O₃ suspensions. With the aid of EDTA-4Na, the adsorption amount of sodium polyacrylic acid (PAA-Na) increased, while the apparent viscosity of 60 vol% Al₂O₃ slurries decreased significantly. Particle size measurements showed that EDTA-4Na could help to reduce larger agglomerates, possibly by modifying the adsorbed layer thickness. The interactions between EDTA-4Na and PAA-Na were studied using Fourier-transform infrared spectroscopy analysis. Results showed that it was possible to introduce EDTA-4Na as the second dispersant to improve the dispersion of high solid content Al₂O₃ slurries.