共查询到20条相似文献,搜索用时 156 毫秒
1.
为了提高电容式MEMS加速度计测量精度,设计了一种应用于MEMS加速度计微弱信号读出电路。读出电路由T型阻容网络放大电路、模拟开关解调电路和四阶带通滤波电路组成,通过Multisim软件仿真分析各模块电路原理并确定影响读出电路的主要因素,进一步优化确定元器件最佳参数,最后制作出PCB电路板并开展实验测试,实验结果表明微弱信号检测准确率达90%以上,能很好满足电容式MEMS加速度计微弱信号检测要求,同时该读出电路具有尺寸小、易调节、易于ASIC集成等特点,在微机械仪表的微小电容检测中有较高的实用价值。 相似文献
2.
3.
基于频分复用的多路微电容检测技术 总被引:1,自引:0,他引:1
为使静电悬浮微电机的环形转子稳定悬浮在定子电极腔体的几何中心,需要采用差动电容式传感器检测转子沿五个自由度的运动,然后通过静电悬浮控制系统实现有源静电支承。根据频分复用原理,设计了一套可检测悬浮式转子五个自由度运动的微电容检测电路。采用多路高频正弦信号作为载波加载至与各自由度对应的控制/检测电极上,通过公共电极输出反映转子沿各自由度位移变化的调幅信号,然后经过交流放大、相敏解调、低通滤波后得到各自由度位移检测信号。文中介绍了微电容检测电路的组成及原理,分析了电路特性,给出了x轴检测电路的测试结果。实验表明,检测电路的灵敏度为23.3 V/pF,通频带为10.58 kHz,零位稳定性优于0.1 mV。 相似文献
4.
5.
针对硅微加速度计中微小差分电容检测,提出了一种基于调制解调方法的闭环检测电路,介绍了该闭环检测系统的原理框图和实现途径。分析了基于单路载波的前置电容-电压( C-V)转换电路,证明了基于相关芯片的解调方法的有效性,其解调效率仅对开环输出有影响;基于双路反馈电路的静电力平衡回路有效提高该检测系统的线性度。结合硅微加速度计参数和电路设计参数,对加速度计系统进行了仿真,仿真结果显示系统稳定,刻度系数为0.9 V/gn 左右,带宽700 Hz左右。结合表头进行的精密转台实验结果表明该加速度计系统刻度系数0.88 V/gn,量程可达±13 gn。 相似文献
6.
低温共烧陶瓷(LTCC)技术是实现电子设备小型化、高密度集成化的主流封装/组装集成技术,可适用于耐高温、耐受恶劣环境下的特性要求。报道了以LTCC为结构材料设计、制作的一种MEMS差分电容式加速度计。该器件的敏感质量、4根悬臂梁结构都内嵌于LTCC多层基板,质量块和上下盖板之间通过印刷电极组成差分电容对;高精度电容检测芯片表贴于LTCC基板表面,将差分电容信号转化为电压信号。论文讨论了微机械LTCC加速度计的设计与制备、检测电路和性能测试。LTCC的高密度多层布线减小了互连线的长度和相关耦合寄生电容;基于集成芯片的检测电路解决了分立式检测电路的引起噪声大、电路复杂等问题。测试结果表明:该加速度计结构灵敏度较高,小载荷情况下表现出良好的线性关系,灵敏度约为30.3 mV/gn。 相似文献
7.
低温共烧陶瓷(LTCC)技术是实现电子设备小型化、高密度集成化的主流封装/组装集成技术,可适用于耐高温、耐受恶劣环境下的特性要求。本文报道了以LTCC为结构材料设计、制作的一种MEMS差分电容式加速度计。该器件的敏感质量、四根悬臂梁结构都内嵌于LTCC多层基板,质量块和上下盖板之间通过印刷电极组成差分电容对;高精度电容检测芯片表贴于LTCC基板表面,将差分电容信号转化为电压信号。论文讨论了微机械LTCC加速度计的设计与制备、检测电路和性能测试。LTCC的高密度多层布线减小了互连线的长度和相关耦合寄生电容;基于集成芯片的检测电路解决了分立式检测电路的引起噪声大、电路复杂等问题。测试结果表明:该加速度计结构灵敏度较高,小载荷情况下表现出良好的线性关系,灵敏度约为30.3mV/g。 相似文献
8.
9.
10.
11.
Reconfigurable millimeter-wave filters using CPW-based periodic structures with novel multiple-contact MEMS switches 总被引:1,自引:0,他引:1
Jae-Hyoung Park Sanghyo Lee Jung-Mu Kim Hong-Teuk Kim Youngwoo Kwon Yong-Kweon Kim 《Journal of microelectromechanical systems》2005,14(3):456-463
In this paper, fully monolithic reconfigurable millimeter-wave filters are proposed using the CPW-based periodic structures with novel multiple-contact MEMS switches. Millimeter-wave low-pass and band-pass filters were designed, fabricated, and tested. Three cascaded CPW-based periodic structures, with low-pass and band-pass intrinsic filtering characteristics, are reconfigured into a self-similar single unit cell by the operation of the novel multiple-contact MEMS switches with single actuation. By using the multiple-contact MEMS switches, the insertion loss can be reduced and the operating frequency ranges are extended to millimeter-waves with little increase of loss. Additionally, the number of the switching elements has been reduced and the bias-decoupling circuits are not required, resulting in a very small chip size. The measured results of the reconfigurable low-pass filter show the 3-dB cutoff frequency change from 67 to 28 GHz with very small change in the insertion loss from 0.32 to 0.27 dB. The center frequency of the reconfigurable band-pass filter is tuned from 55 to 20 GHz, and the measured 3-dB cutoff bandwidth changed from 32 to 12 GHz, while the average insertion loss changed from 1.27 to 1.61 dB. The chip size of the low-pass and band-pass filter including dc bias line is 1.2 mm /spl times/ 1.5 mm and 1.2 mm /spl times/ 4.5 mm, respectively. 相似文献
12.
在研究两轮自平衡电动车的平衡控制的基础上,设计了基于MEMS组合模块的姿态测量系统.通过对各MEMS传感器输出信号特征的提取、分析,将离散化低通滤波器模型与互补滤波的思想相结合,巧妙地构造出一种便于本系统实现的数据融合模型.同时,提供了一种基于MEMS组合模块姿态检测的低成本、可行性方案. 相似文献
13.
14.
15.
16.
A method is introduced to measure the micro-capacitance for MEMS comb actuators whose value is in pF even fF magnitude. This
method uses so called peak detection measuring technology to realize this purpose. It is mainly composed of the signal generating
circuits, C/V (Capacitance/Voltage) converting part, peak detector circuits and the digital solution element. In order to
verify the correctness of the design, detailed theory analysis and simulation are made for every composed portion and corresponding
mathematical model is built. It is concluded from the analyzed result that precision of the system can reach 237 aF for 0.98–2 pF
measuring range. When corresponding measuring electric circuits is fabricated and debugged, high precision calibration device
named Agilent E4980A is used to calibrate it. It is concluded from the calibrated result that the output voltage of the measurement
circuit and the micro capacitance have good linear relationship, which verifies the correctness of the pertinent theory. Finally,
in order to verify the correctness of the design, dynamic characters of a resonant MEMS gyroscope, which is fabricated with
bulk technology and bonding process, is tested with this device. It is concluded from the measured result that relative error
of the resonant frequency between the ideal value and the measured result is just 0.02%. Quality factor of this sensor is
312.5. Experimental results indicate this scheme is feasible to measure the static and dynamic characters of micro capacitors. 相似文献
17.
针对传统的电路板测点选取方法需要的输入信息多、工作繁琐、效率低及难以得到全局最优解等问题,提出了一种基于多信号模型与遗传算法相结合的优化方法。首先,通过建立板级电路的多信号流系统模型,获取测点与对应板级电路组成单元的相关性矩阵,并对其进行进一步分析,得出测点组合的测试能力参数。在测点选取数量不大于给定值的情况下,选取测试能力参数作为遗传算法的适应度函数并进行优化搜索,以确定测点的优化选取方案。结合Multisim仿真软件进行低通有源滤波电路系统的故障模拟实验,仿真结果表明,基于多信号模型与遗传算法选取的板级电路测点组合对低通有源滤波电路中的绝大部分故障都有良好的检测和隔离能力,取得了良好的效果,同时该方法也适用于多种其他电路。 相似文献
18.
19.
20.
针对飞行器导航控制系统姿态信息的远程无线数据采集物理仿真及工程应用需求和数据采集系统应具有实时性能好、高精度及高可靠性等技术性能要求,设计和实现了陀螺远程综合测试系统;测试系统采用实验转台提供标准角速度信号,光纤陀螺作检测标准,待测陀螺为微机械陀螺;采用了巴特沃斯低通滤波器和滑动均值滤波器联合对采集的陀螺数据进行滤波处理;对标度因数、非线性度、最大角速度等部分常用技术参数的测试及计算方法做了分析,用辨识法对陀螺系统模型进行了建模,从而提高了数据采集的准确性;经实验验证,测试系统实现了远程无线数据采集的功能,被测陀螺的检测数据及陀螺模型能够反映实际效果,其准确性、实时性及供电系统的性能均满足了设计的预期要求. 相似文献