共查询到17条相似文献,搜索用时 54 毫秒
1.
3.
4.
脲基润滑脂性能优良,介绍了脲基润滑脂在烧结系统的应用情况,在烧结系统使用脲基润滑脂可以简化润滑设备,节约设备维护费用,提高综合经济效益。 相似文献
5.
脲基脂有优良的耐热和氧化安定性能,已经广泛用于钢厂设备和汽车的各个润滑部位,并且用量逐年增长,因此对脲基脂润滑机理的研究也盛行起来。在长期使用脲基脂的轴承滚动面上观察到褐色乃至黑色的现象。使用脲基脂的轴承滚动面的磨损程度明显地比使用皂基脂的小。这些现象是脲基脂所特有的。为此进行了脲基脂的染色现象和抗磨性的研究。 相似文献
6.
钢厂设备的润滑改进可以获得巨大的经济效益:减少停机时间,提高生产率;减少磨损,降低备件的更换量;延长设备的寿命:减少摩擦,节约能耗;减少润滑剂的消耗量等。早在10年前,美国就重视钢铁工业的润 相似文献
7.
8.
9.
采用单因素试验法,通过考察润滑油基础油(简称基础油)种类、加料顺序、转化阶段反应温度与反应时间对制得润滑脂性能的影响,优化高碱值复合磺酸钙基润滑脂的制备工艺。结果表明:在以基础油A为润滑脂基础油、加料顺序为在转化阶段同时加入高碱值磺酸钙和脂肪酸D、转化反应温度为85℃、反应时间为2.5 h的条件下制得的高碱值复合磺酸钙基润滑脂的性能最好,其滴点超过343℃,高于GB/T 3498—2008标准中的滴点高限,工作锥入度(0.1 mm)为279,钢网分油率为2.17%,极压抗磨性能优秀,多项性能优于市售同类润滑脂。 相似文献
10.
复合磺酸钙基润滑脂是优良的通用润滑脂.介绍了复合磺酸钙基润滑脂的高低温性能,极压抗磨性能,抗水性能,氧化安定性能以及在造纸、钢铁、核电厂、汽车行业的应用. 相似文献
11.
文章主要讲述了一种具有优良高温性能、高负荷以及良好抗水性能的轧辊轴承润滑脂,与以前轧机使用的极压锂基润滑脂相比,这是专门针对钢厂轧机设计的一种能够延长换脂周期的润滑脂。通过轧辊轴承润滑脂在西北一家钢厂轧机上的应用,证明该产品性能完全满足轧机高温、高负荷和水冲刷工况的使用要求,并使其换脂周期从30天提高到45天,使用轧辊轴承润滑脂全年的润滑费用降低近6万元。在检维修周期延长后,减少检维修次数,全年轧钢工段可降低润滑费用和检维修费用共计约40万元。保障了钢厂轧机的正常运转,降低了工人的劳动强度和生产成本。 相似文献
12.
Liu Yinong 《中国炼油与石油化工》2015,17(1):89-95
Six kinds of alkylbenzene sulfonic acids were selected to prepare the sulfonates S1—S6. Among them, the sulfonates S3, S4, and S6 could be incorporated into lubricating grease with good performance in comparison with the grease produced from commercial sulfonates T106-1 and T106-2. The optimized conditions for synthesis of the sulfonates S3, S4, and S6 were explored by using different mass ratios of methanol, water and the type of copromoters. It was found out that the appropriate conditions for synthesis of the sulfonate S3 included a methanol to M(M is the total mass of alkylbenzene sulfonic acid and base oil) mass ratio of 16%, a water to M mass ratio of 4%, and a copromoter A to M mass ratio of 2%; the appropriate conditions for synthesis of the sulfonate S4 included a methanol to M mass ratio of 24%, a water to M mass ratio of 2%, a copromoter B to M mass ratio of 2%; and the optimized conditions for synthesis of the sulfonate S6 included a methanol/ M mass ratio of 8%, a water/M mass ratio of 4% and a copromoter B/M mass ratio of 2%. The new sulfonates S3, S4, and S6 produced under the optimized conditions exhibited higher TBN and better antiwear property in camparison with the previous products. Grease samples G9, G10, and G11 were prepared with new sulfonates S3, S4, and S6 successfully and exhibited improved water stability and high temperature performance. 相似文献
13.
14.
15.
16.
17.
In the 1950’s, complex calcium lubricating grease had been widely used. However, due to the hardening problem in the process of storage and use, the production of complex calcium lubricating grease decreases year by year. Domestic and foreign researchers have done a lot of work on its hardening problem, and it has been found that boric acid and phosphoric acid can effectively improve the hardening problem. In this paper, the water absorption test of several calcium salts was carried out, and it was found that calcium 12-hydroxystearate did not absorb water, and calcium acetate, calcium phosphate and calcium borate had different degrees of water absorption. Calcium acetate has the highest water absorption rate, and calcium phosphate and calcium borate have comparable water absorption rates. Using molecular simulation technology, it is found that in the complex calcium grease system, calcium phosphate and calcium borate prefers to combine with water, which inhibits the water absorption of calcium acetate and makes the hardening problem better. 相似文献