微波法合成树枝状纳米硫化锑

以氯化锑、硫脲为原料,采用微波法合成树枝状硫化锑纳米材料。用X射线粉末衍射（XRD）、扫描电子显微镜（SEM）和X射线能谱（EDS）等对Sb2S3晶体的物相及形貌进行分析表征。结果表明制备出的是正交相Sb2S3,长度可达数十微米。并给出树枝状硫化锑纳米材料的可能的形成机理。     

PC/ABS合金的气相/凝聚相协同阻燃作用

分别选用2种不同阻燃机理的磷系阻燃剂,即以凝聚相阻燃为主的间苯二酚-双(二苯基磷酸酯) (RDP)和以气相阻燃为主的磷酸三苯酯(TPP),采用熔融共混法制备聚碳酸酯(PC)/丙烯腈-丁二烯-苯乙烯共聚物(ABS)阻燃合金. 通过垂直燃烧测试和锥形量热测试探究RDP/TPP复配对合金阻燃性能的影响,通过扫描电子显微镜(SEM)观察燃烧残炭的微观形貌. 以甲基丙烯酸甲酯-丁二烯-苯乙烯(MBS)为相容剂,通过拉伸性能和冲击性能测试探究MBS对阻燃合金的增韧增容效果,并以SEM观察MBS对合金相界面和相形态的影响. 结果表明,RDP的凝聚相阻燃和TPP的气相阻燃作用具有协同效果,可以在PC/ABS合金中促进磷酸盐结构生成,进而有助于体系生成更连续、致密的炭层.     

Pressureless reactive sintering mechanism of nanocrystalline Bi2O3-Y2O3 solid electrolyte

The nanocrystalline Bi2O3-Y2O3 solid electrolyte material was synthesized by pressureless reactive sintering process with Bi2O3 and Y2O3 nano mixed powder as raw materials, which was prepared by a chemical coprecipitation process. The study on the behavior of nano δ-Bi2O3 formation and its grain growth showed that the solid solution reaction of Y2O3 and β-Bi2O3 to form δ-Bi2O3occurs mainly in the initial stage of sintering process, and nano δ-Bi2O3 crystal grains grow approximately following the rule of paracurve ((D-D0)2=K.t) during sintering process. After sintered at 600℃ for 2 h, the samples could reach above 96% in relative density and have dense microstructure with few remaining pores, the δ-Bi2O3 grains are less than 100 nm in size.     

氧化铝增强的PdSe2/Si异质结光电探测器

为了降低暗电流,通过原子层沉积(ALD)生长了一层氧化铝(Al₂O₃)隧穿层,制备了PdSe₂/Al₂O₃/Si异质结光电探测器.通过优化Al₂O₃层的厚度,使得该探测器实现了高速和宽光谱响应.研究结果表明,在波长为808 nm的光照射和-2 V偏压下,所制备的光电探测器与未生长Al₂O₃的器件相比,暗电流降低了约3个数量级,器件的光响应度达到了约为0.31 A/W,对应的比探测率约为2.5×10¹² Jones,器件在零偏压下表现出明显的自驱动效应.经过循环测试1 200次后,器件保持良好的光响应.器件响应的上升时间和下降时间分别为7.1和15.6μs.结果表明,在二维层状半导体材料与Si之间引入Al₂O₃隧穿层,可以有效地降低器件的暗电流,有利于高性能的Si基光电探测器的制备.     

Reaction dynamics in the combustion synthesis system of Al-CrO3-Al2O3-NaF-N2-O2

A new material with heat-resistant and adiabatic characteristics and high strength was prepared using the combustion synthesis method by mixed powders of CrO3, Al, Al2O3, and NaF in atmospheric gas. The reaction dynamic process of the Al-CrO3-NaF-Al2O3-N2-O2 new material system by the combustion synthesis method was discussed based on the observation results by SEM, EDS, and XRD in combination with the combustion front quenching method （CFQM） and the relation curves between reaction free enthalpies and the corresponding temperatures. The combustion synthesis mechanism and the formation reasons of the phase in the combustion product were analyzed.     

Degradation of p-nitrotoluene by O3/H2O2 process and oxidation mechanism

The degradation of p-nitrotoluene by O3/H2O2 process in a bubble contact column was investigated. Effects of the molar ratio of hydrogen peroxide to ozone,pH value and t-butanol on the oxidation process were discussed. It was found that the proper H2O2/O3 molar ratio for the degradation of p-nitrotoluene was around 0.6, different pH values and the presence of t-butanol highly influenced the removal efficiency of p-nitrotoluene. 5-methyl-2-nitrophenol, 2-methyl-5-nitrophenol, (4-nitrophenyl) methanol, 5-(hydroxymethyl)-2-nitro phenol, acetic acid, 2-methylpropane diacid and 2-(hydroxylmethyl)propane diacid were identified as degradation intermediates and products through GC-MS. Radical reaction mechanism and degradation pathway were proposed based on the results of experiments. It is deduced that the benzene ring of p-nitrotoluene can be only destroyed by hydroxyl radicals through a polyhydroxy intermediate pathway. Then unstable polyhydroxy intermediates can be oxidized to different acids with low molecular weight rapidly.     

W-Sc2O3靶材的SPS制备和性能研究

采用溶胶凝胶法加二段还原, 制备出晶粒直径500~1100 nm的亚微米W-Sc₂O₃粉末, 利用放电等离子烧结(spark plasma sintering, SPS)制备了W-Sc₂O₃靶材.对不同粉末处理条件下的W-Sc₂O₃烧结体的密度、硬度、表面形貌进行测试研究.结果表明, 亚微米尺度的W粉在1 300℃即可烧结, 远低于常规W粉烧结温度, 获得的烧结体相对密度达96.4%、硬度为86.4HRC且Sc元素分布均匀.     

一种基于 MXene 的Fe2O3/Nb2O5/Nb4C3Tx 高灵敏丙酮传感器

MXene 具有较大比表面积和优异的导电性, 当与金属氧化物半导体结合时可以抑制片层团聚, 还可以大大提高载流子转移速率, 提高气敏性能。通过简单的水热和煅烧两步法成功合成了Fe₂O₃/Nb₂O₅/Nb₄C₃T_x 三元复合材料。通过表征, Fe₂O₃ 微米球分布在 MXene 纳米片层之间。气敏测试结果表明, 与原始Fe₂O₃相 比, Fe₂O₃/Nb₂O₅/Nb₄C₃T_x 传感器对丙酮的响应能力有明显的提高。传感器灵敏度高, 选择性较好, 对环境中 浓度为 5 ×10^?6 的丙酮响应高 (R_a /R_g = 7.81, 30% RH), 响应和恢复速度快, 具有出色的重复性和长期稳定性。Fe₂O₃/Nb₂O₅/Nb₄C₃T_x 传感器具有良好的气敏性能, 主要因为三元复合材料提供了较大比表面积和丰富的氧空位, 增强了活性位点, 使得气体易于在传感器表面扩散, 为开发丙酮敏感复合材料提供了参考。     

Solvothermal preparation and characteristics of Sn-doped In2O3

Sn-doped In2O3 （ITO） nanopowders were prepared in ethanol solvent by solvothermal process. The effects of the solvothermal temperature, coprecipitation pH value and SnO2 content on the products phase and microwave absorption were investigated by X-ray diffractometry and microwave reflectance. ITO nanopowders with cubic structure can be respectively prepared at 250 and 270 ℃ for 6 h. The prepared product is InOOH or the mixture of InOOH and In3Sn4O12 when the solvothermal temperature is below 250℃. With rising solvothermal temperature and prolonging time, the absorption of the ITO powders gradually decreases. The products are ITO nanopowders by coprecipitating at pH=9 or 11, but ITO powders with Sn3O4 at pH=6. The absorption of powders prepared at pH=6 is better than that at any other pH value. The products are all ITO nanopowders and crystal size reduces with increasing SnO2 content. The microwave absorption of ITO nanopowders with SnO2 content of 8% （mass fraction） is the best among samples with different SnO2 contents.     

纳米Al2O3改性环氧胶黏剂和钢铁附着机理的研究

通过拉拔法测定纳米Al₂O₃改性环氧胶黏剂和钢铁之间的附着强度,并结合环氧胶的表面能参数测定以及X射线光电子能谱(XPS)分析,对纳米Al₂O₃提高环氧胶和钢铁附着力的机理进行研究.表面能测定结果表明,添加纳米Al₂O₃使环氧胶的极性增加;XPS能谱分析结果表明,当纳米Al₂O₃质量分数达到2%时,环氧胶中形成新的羧基极性基团;进一步研究发现,当纳米Al₂O₃质量分数为1%时未形成新的羧基基团,当纳米Al₂O₃质量分数为8%时单位接触面积上新的羧基基团的数目较2%时少,这与附着强度的变化规律是一致的.因此,纳米Al₂O₃改性的环氧胶黏剂与钢铁的附着强度的增强是由于Al₂O₃与环氧胶的相互作用形成了新的羧基极性基团．     

Bi2O3和Fe2O3掺杂对BaTiO3陶瓷显微结构的影响

利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线能量色散谱(EDAX)等结构分析技术,研究了施主(Bi     

Modification of nano-TiO2 by Al2O3 in-situ coating

A novel technology of in-situ coating Al₂O₃ on the surface of H₄TiO₄ was developed to prevent the aggregation of nano-TiO₂ powders and improve the dispersibility and thermal stability in the way of forming a uniform coating layer. The heterogeneous nucleation was conducted to prepare the precursor of nano-TiO₂ and then Al₂O₃ was coated on the surface of precursor. The effects of Al₂O₃ in-situ coating on the properties of nano-TiO₂ were investigated. The results show that H₄TiO₄ can be dispersed well under alkaline condition (pH 8.5) and the heterogeneous nucleation can be controlled easily. The optimized uniform coating layer is obtained by adding 5% (mass fraction) and 10% of Al₂O₃ and the aggregation of nano-TiO₂ powders is effectively inhibited and the dispersibility is obviously improved. The crystal sizes of TiO₂ powders are 12.3, 11.4 and 8.7 nm after coating 0,5% and 10% of Al₂O₃ respectively. Al₂O₃ on the surface of particulates in amorphous phase could increase the thermal stability of nano-particles after calcined at 550 °C. Foundation item: Project(04GK2007) supported by Hunan Industrial Key Project of Science and Technology     

基于双金属MOFs 制备Co3O4/In2O3 复合物及其气敏性能的研究

以硝酸铟(In(NO₃)₃·xH₂O)、对苯二甲酸(H₂BDC)、六水合硝酸钴(Co(NO₃)· 6H₂O) 为原料, 首先采用一锅油浴法合成了含有Co²⁺ 的铟基金属有机框架材料(MOFs) Co²⁺/CPP-3(In) 材料, 然后在450 ℃ 下焙烧制备Co₃O₄/In₂O₃ 复合物气敏材料, 将Co₃O₄/In₂O₃ 复合物的粉体制作成传感器, 并对其气敏性能进行研究。利用扫描电子显微镜和X 射线衍射仪(XRD) 对双金属MOFs Co²⁺/CPP-3(In) 材料和Co₃O₄/In₂O₃ 复合物进行表征, 采用静态配气法测试其气敏性能。结果表明, Co₃O₄/In₂O₃(n_Co : n_In = 0.4 : 1) 样品的形貌保留了其MOFs 前驱体的棒状结构, 棱柱形框架更为突出, 表面呈凹陷状, 棒体中间粗两边细, 六角截面和棒体均布满了孔洞。结合EDX 和XRD 表征结果, Co²⁺/CPP-3(In) MOFs 前驱体完全转化成Co₃O₄/In₂O₃ 复合物; Co₃O₄/In₂O₃(n_Co : n_In = 0.4 : 1) 复合物在 70 ℃ 下对5×10^-6 H₂S 的气敏性能最优, 响应值达到153, 是同条件下纯备In₂O₃对H₂S 响应值的5 倍, 并且有较好的重复性、选择性和稳定性。     

Pressureless sintered 3Y-TZP/20%Al2O3 composite ceramic

Nanometer 3Y-TZP/20%Al₂O₃ (mass fraction) composite powders prepared by the chemical coprecipitation method were pressureless sintered at 1550 °C for 2 h. Effects of calcining temperatures at 800 °C, 1 000 °C, and 1 200 °C on phase structure, relative density, and Vicker’s hardness of the sintered bodies were studied. The results show that 1 000 °C was the optimal calcining temperature, and the powder calcined was composed of tetragonal zirconia with the Scherrer crystalline size of 6.3nm. The relative density was up to 98.5% under pressureless sintering, and the sintered body was t-ZrO₂ (without m-ZrO₂)+α-Al₂O₃ with the average size of 0.4 μm. Foundation item: State Key Laboratory for Powder Metallurgy(No.9706-36) Biography of the first author: YIN Bang-yao, born in 1966, majoring in advanced ceramic materials.     

Luminescent properties of BaO-La2O3-B2O3 glasses with dopant

The luminescent properties of glasses synthesized in air atmosphere by conventional high temperature process were stud{ed. The emissions spectra of Eu^2 and Eu^3 were observed in BaO-La2O3-B2O3-Eu2O3 glasses.The results show that the broad emission peaks at 430 nm correspond to 5d→4f emission transition of Eu^2 , the sharp emission peaks at 592, 616, 650 and 250 nm correspond to 5^D0→1Fj(j=1--4) emission transition of Eu^3 ,respectively, which indicates that the BaO-La2O3a-B2O3-Eu2O3 glass can convert ultraviolet and green omponents of sunlight into blue and red light so as to increase the intensity of blue and red light, respectively. The luminescent in--tensity of Eu^2 increases with increasing the molar ratio of Tb^3 in BaO-La2O3-B2O3-Eu2O3a-Tb4O3 glasses, whereas the luminescent intensity of Eua^3 decreases. So the luminescent intensity of Eu(Ⅲ,Ⅱ) is influenced by Tb^3 .These phenomena can be explained by electron transfer mechanism; Eu^3 (4f6) Tb^3 (4f^8)→Eu^2 (4f′) Tb^4 (4f′). Taking advantage of the luminescent properties of BaO-La2O3-B2O3-Eu2O3 glasses, light-conversion glass for agriculture can be produced.     

Structure of Bi2O3-ZnO-B2O3 system low-melting sealing glass

Bi_2O_3-ZnO-B_2O_3 system glass is a kind of lead-free low melting sealing glasses. The structure of Bi_2O_3-ZnO-B_2O_3 system low-melting sealing glass was investigated by DSC, FT-IR, XRD and SEM. The results show that with the increase of B_2O_3 content, the transition temperature Tg and softening temperature T_f of Bi_2O_3-ZnO-B_2O_3 system low-melting sealing glasses increase, which leads to the liquid phase precipitation temperature increasing and promotes the structure stability in the glass. With increasing the heat treatment temperature, a large number of liquid phases appear in samples and the sinter efficiency of the samples increases. The FT-IR spectra of the glasses show the presence of some bands that are assigned to vibrations of Bi-O bond from [BO_3] pyramidal and [BiO_6] octahedral units and B-O from [BO_3] and [BO_4] units. With the decrease of B_2O_3 content, the crystallization tendency of the glass increases. In glass samples B_1 and B_2, crystallization starts at 460 ℃ and 540 ℃, respectively. Both of them precipitate Bi-(24)B_2O_(39) phases.     

Dielectric properties of Pb (Zn1/3 Nb2/3) O3?PbZrO3?PbTiO3 solid solution near morphotropic phase boundary

The dielectric properties of Pb(Zn_1/3Nb_2/3) O₃-PbZrO₃−PbTiO₃ (PZN-PZ-PT) system near the rhombohedral/tetragonal morphotropic phase boundary (MPB) are carefully studied in this paper. It is found that, for all samples, the curves around the temperatures of dielectric permittivity peak show the characteristics of diffuse phase transition. The change in PbZrO₃/PbTiO₃ ratio has much influence on the dielectric properties of the samples. The extent of diffuse phase transition increases with the increasing Zr/Ti ratio. The samples in rhombohedral region have typical diffuse phase transition in the temperature range measured. However, for the samples with tetragonal symmetry, a spontaneous normal ferroelectric-relaxor phase transition exists at temperature lower than that of permittivity peak. This normal ferroelectric-relaxor phase transition is confirmed by the experiment of thermally driven current. The analysis of TEM reveals that the samples in tetragonal region show a 90% macrodomain structure, while the samples in rhombohedral region have the configuration of microdomain structure.     

SnO2及SnO2／Fe2O3复合微米材料的合成及表征

本文首先以SnCl2·2H2O为主要原料,无水乙醇为溶剂,利用溶剂热法于180℃反应24h得到了SnO2微球;再以所制备的SnO2微球为前驱体,FeCl3·6H2O为主要原料,通过水热法得到SnO2／Fe2O3复合材料．利用X射线粉末衍射仪（XRD）和扫描电子显微镜（SEM）对所得产物进行了表征．结果表明：所得的SnO2为四方锡石型,形貌为微球,平均直径约为2．0μm;复合后得到的SnO2／Fe2O3微球平均直径约为2．5μm．其中,Fe2O3为六方赤铁矿型,在复合物的表面以小颗粒的形式存在,尺寸约为200nm．另外,也对SnO3与SnO2／Fe2O3微球的形成过程进行了讨论．     

Al2O3抗热震陶瓷的研究进展

为了增进对Al₂O₃抗热震陶瓷发展动态的了解,为Al₂O₃抗热震陶瓷的制备提供设计依据,针对Al₂O₃抗热震陶瓷的常用抗热震性测试方法,Al₂O₃陶瓷微观结构、表面条件、尺寸对抗热震性的影响,利用第二相法提高Al₂O₃陶瓷抗热震性的可行性,以及多孔Al₂O₃抗热震陶瓷的研究进展等方面进行了评述.在Al₂O₃陶瓷中添加ZrO₂、稀土化合物、低热膨胀系数组元或高热导率组元等可以改善Al₂O₃陶瓷的抗弯强度、断裂韧性、弹性模量等力学性能和(或)热膨胀系数、热导率等热学性能,从而起到提高Al₂O₃陶瓷抗热震性能的作用.叠层Al₂O₃复合抗热震陶瓷将成为今后的一个研究方向.     

Microstructure and microwave dielectric properties of CaO-B2O3-SiO2 glass ceramics with various B2O3 contents

The effects of B2O3 addition on both the sintering behavior and microwave dielectric properties of CaO-B2O3-SiO2 (CBS) glass ceramics were investigated by Fourier transform infrared spectroscopy (FTIR),X-ray diffractometry (XRD) and scanning electron microscopy (SEM).The results show that the increasing amount of B2O3 causes the increase of the contents of [BO3],[BO4] and [SiO4],which deduces the increase of CaB2O4 and α-SiO2 and the decrease of CaSiO3 correspondingly.No new phase is observed throughout the...