Suface grafting of polymers onto nanodiamond by ligand-exchange reaction of ferrocene moieties of polymers with polycondensed aromatic rings of the surface

To improve the dispersibility of nanodiamond (ND) in solvents and polymer matrices, the grafting of copolymers containing vinyl ferrocene (Vf) onto the surface by a ligand-exchange reaction with ferrocene moieties of the copolymer and polycondensed aromatic rings of ND surface was investigated. The copolymer containing Vf was prepared by the radical copolymerization of Vf with vinyl monomers, such as methyl methacrylate (MMA), styrene (St), and N-isopropylacrylamide (NIPAM), using 2, 2′-azobisisobutyronitrile as an initiator. It was found that by heating of ND with poly(Vf-co-MMA), poly(Vf-co-St), and poly(Vf-co-NIPAN) in the presence of AlCl₃ and Al powder as catalysts, the corresponding copolymer was successfully grafted onto the surface. On the contrary, in the absence of AlCl₃, no grafting of these copolymers was observed. The grafting of polymers onto the ND surface was confirmed by FT-IR. These polymer-grafted NDs were found to give stable dispersions in solvents for the grafted polymer. In addition, the dispersibility of poly(Vf-co-NIPAM)-grafted ND uniformly dispersed in water below 32 °C but precipitated above the temperature. Therefore, it was concluded that the dispersibility of ND in water could be controlled by the temperature of water.     

Functionalization of MWCNT with P(MMA-co-S) copolymers via ATRP: Influence on localization of MWCNT in SAN/PPE 40/60 blends and on rheological and dielectric properties of the composites

In this work, the localization of functionalized multi-walled carbon nanotubes (MWCNT) with random copolymers of methyl methacrylate and styrene (P(MMA-co-S)) in poly(styrene-co-acrylonitrile)/poly(2, 6-dimethyl-1,4-phenylene ether) blends (SAN/PPE) and its influence on morphological, rheological and dielectric properties of the composites were investigated. P(MMA-co-S) copolymers were grafted onto MWCNT via atom transfer radical polymerization (ATRP). The molecular weight of the copolymers was adjusted by controlling the time of reaction. In SAN/PPE blends, MWCNT grafted with low molecular weight copolymers were predominantly located at the interface of the blend and a few individual tubes were dispersed in the PPE phase. Aggregation of MWCNT was observed nearby the interfacial region because of micellization of grafted copolymers. Aggregation was more pronounced with increasing molecular weight of the grafted P(MMA-co-S) copolymer. In the melt, the composite containing MWCNT with low molecular weight copolymers had higher dynamic moduli than the one with pristine MWCNT. An increasing molecular weight of grafted copolymer led to a softening effect which resulted in a reduction of the moduli of the composite. Although a pronounced enhancement was observed for the composites with pristine MWCNT, only a small increase in electrical conductivity was achieved by adding functionalized MWCNT owing to the poor network formed by functionalized MWCNT in the blends.     

Grafting of branched polymers onto the surface of vapor grown carbon fiber and their electric properties

The grafting of branched polymers onto vapor grown carbon fiber (VGCF) surface and their electric properties of the composite prepared from the branched polymer-grafted VGCF were investigated. In the first step, the grafting of copolymers having pendant peroxy groups onto VGCF was achieved by the copolymerization of 1-(t-butylperoxy-i-propyl)-3-i-propenylbenzene (BPPB) with vinyl monomers initiated by the system consisting of Mo(CO)₆ and trichloroacetyl groups previously introduced onto the surface. In the second step, the postpolymerization of vinyl monomers was initiated by pendant peroxy groups of grafted poly(vinyl monomer-co-BPPB) on the surface to give branched vinyl polymer-grafted VGCF. The dispersibility of VGCF in THF was remarkably improved by grafting of branched polymers onto the surface. The electric resistance of composites prepared from the branched polymer-grafted VGCF suddenly increased when the composites were transferred into solvent vapors and suddenly decreased when they were transferred to dry air.     

Novel strategy for ternary polymer blend compatibilization

A novel strategy for compatibilization of ternary polymer blends was described. PP (polyolefins)/PA6 (engineering plastics)/PS (styrene polymers) was selected as a model ternary blend system, and the compatibilization effect was investigated by means of SEM, rheometer, dynamic mechanical thermal analysis and mechanical testing. The results indicated that, as a ternary polymer blend compatibilizer, styrene and maleic anhydride dual monomers melt grafted polypropylene [PP-g-(MAH-co-St)] showed more effective compatibilization in the PP/PA6/PS ternary blend system than PP-g-MAH, PP-g-St and their mixture. The good compatibilizing effect of PP-g-(MAH-co-St) can be explained by two mechanisms. One is the in situ formation of [PP-g-(MAH-co-St)]-g-PA6 copolymer at the PP/PA6 interface, and the other is that it also contains styrene blocks, resulting in chemical affinity with PS and PP homopolymers.     

Synthesis and characterization of graft copolymers of syndiotactic polystyrene with polybutadiene and 4‐methylstyrene

The basic method for synthesizing syndiotactic polystyrene‐g‐polybutadiene graft copolymers was investigated. First, the syndiotactic polystyrene copolymer, poly(styrene‐co‐4‐methylstyrene), was prepared by the copolymerization of styrene and 4‐methylstyrene monomer with a trichloro(pentamethyl cyclopentadienyl) titanium(IV)/modified methylaluminoxane system as a metallocene catalyst at 50°C. Then, the polymerization proceeded in an argon atmosphere at the ambient pressure, and after purification by extraction, the copolymer structure was confirmed with ¹H‐NMR. Lastly, the copolymer was grafted with polybutadiene (a ready‐made commercialized unsaturated elastomer) by anionic grafting reactions with a metallation reagent. In this step, poly(styrene‐co‐4‐methylstyrene) was deprotonated at the methyl group of 4‐methylstyrene by butyl lithium and further reacted with polybutadiene to graft polybutadiene onto the deprotonated methyl of the poly(styrene‐co‐4‐methylstyrene) backbone. After purification of the graft copolymer by Soxhlet extraction, the grafting reaction copolymer structure was confirmed with ¹H‐NMR. These graft copolymers showed high melting temperatures (240–250°C) and were different from normal anionic styrene–butadiene copolymers because of the presence of crystalline syndiotactic polystyrene segments. Usually, highly syndiotactic polystyrene has a glass‐transition temperature of 100°C and behaves like a glassy polymer (possessing brittle mechanical properties) at room temperature. Thus, the graft copolymer can be used as a compatibilizer in syndiotactic polystyrene blends to modify the mechanical properties to compensate for the glassy properties of pure syndiotactic polystyrene at room temperature. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

New macromolecular silane coupling agents synthesized by living anionic polymerization; grafting of these polymers onto inorganic particles and metals

New macromolecular silane coupling agents, which are end-triethoxysilylated poly(styrene) and poly(tert-butylmethacrylate), were investigated as possible inorganic particle and metal surface treatment agents. These polymers containing poly(styrene) and poly(tert-butylmethacrylate) as the main chain, were prepared by living anionic polymerization. Grafting of the polymers onto inorganic particles and metals was performed via the hydrolysis of the triethoxysilyl group using either acidic or basic catalyst. n-Butylphosphate was used as the catalyst for grafting onto inorganic substances having an acidic surface such as silica. However, in the case of grafting onto inorganic substances having a basic surface, tetrabutylammoniumhydroxide was employed as the catalyst. Contrary to expectations, grafting onto titania was successful even in the absence of a catalyst. Particles grafted with these polymers showed excellent dispersibility in organic medium, in which the polymers are soluble. This phenomenon is in contrast to that for particles treated with polymers possessing triethoxysilyl groups at random positions of the chain or those treated with trimethylsilyl groups. Surface tension measurements of metal substrates coated with the grafted polymers, were found to be identical to the values obtained for the bulk polymers.     

Grafting of polymers onto vapor grown carbon fiber surface by ligand-exchange reaction of ferrocene moieties of polymer with polycondensed aromatic rings of the wall-surface

To improve the dispersibility of vapor grown carbon fiber (VGCF) in solvents, the grafting of copolymer containing vinyl ferrocene (VFE) onto the surface by ligand-exchange reaction between ferrocene moieties of the copolymer and polycondensed aromatic rings of VGCF was investigated. The copolymer containing VFE was prepared by the radical copolymerization of VFE with methyl methacrylate (MMA) using 2, 2′-azobisisobutyronitrole as an initiator. It was found that by heating of VGCF with poly(VFE-co-MMA) in the presence of AlCl₃ and Al powder, the copolymer was grafted onto the wall-surface: the percentage of grafting reached to 57.5%. It is considered that the copolymer was grafted onto VGCF surface by ligand-exchange reaction between ferrocene moieties of the copolymer and polycondensed aromatic rings of VGCF. In addition, carboxyl groups were successfully introduced onto VGCF wall-surface by the ligand-exchange reaction of 1,1′-dicarboxyferrocene with VGCF in the presence of AlCl₃ and Al powder. The carboxyl groups on VGCF were reacted with hydroxyl-terminated polymers to give the corresponding polymer-grafted VGCF. The polymer-grafted VGCF gave a stable colloidal dispersion in solvents for grafted polymer. The electric properties of composite prepared from polymer-grafted VGCF in solvent vapor were investigated.     

Functional biohybrid materials synthesized via surface-initiated MADIX/RAFT polymerization from renewable natural wood fiber: Grafting of polymer as non leaching preservative

Crude wood fibers represent a wide class of renewable resources. The surface modification of such materials via covalent grafting of polymer offers new surface properties with non-leaching coating. The grafting of the polymer chains was achieved by surface-initiated controlled radical polymerization through a grafted xanthate chain transfer agent. Macromolecular design via interchange of xanthate (MADIX) technique was chosen to graft poly(vinyl acetate), polystyrene, poly(n-butyl acrylate) and poly(4-vinylbenzyl chloride)-polystyrene amphiphilic cationic copolymers. Water contact angle measurements highlighted the hydrophobization of the wood fiber surface with a nanoscaled polymer monolayer indicating the appropriate coverage of the fiber. X-ray photoelectron spectroscopy showed the successful grafting of the polymer after drastic washing procedure. The quaternization of the grafted polystyrene-co-poly(4-vinyl benzyl chloride) copolymers with tertiary amine allows the introduction of biocide quaternary ammonium functions while preserving the hydrophobic character of the modified wood fiber when introducing a long alkyl chain in the statistical copolymer. Finally, the cationic copolymer was subjected to Coniophora Puteana to evaluate its propensity to limit the fungi expansion.     

Proton exchange membranes prepared by simultaneous radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) films. I. Effect of grafting conditions

The simultaneous radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films was studied at room temperature. The effects of grafting conditions (type of solvent, irradiation dose, dose rate, and monomer concentration) were investigated. The degree of grafting was found to be dependent on the investigated grafting conditions. The dependence of the initial rate of grafting on the dose rate and the monomer concentration was found to be of 0.5 and 1.3 orders, respectively. The results suggest that grafting proceeds by the so‐called front mechanism in which the grafting front starts at the surface of the film and moves internally toward the middle of the film by successive diffusion of styrene through the grafted layers. Some selected properties of the grafted films were evaluated in correlation with the degree of grafting. We found that the grafted FEP films possess good mechanical stability, which encourages their use for the preparation of proton exchange membranes. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 220–227, 2000     

Initiation of surface graft polymerization by ceric ions on polymer microspheres

The surface graft polymerization of acrylamide on poly(styrene‐co‐acrylonitrile) copolymer microspheres by the initiation of ceric ions was studied. The grafting was verified by IR spectra and X‐ray photoelectron spectroscopy measurements. The resultant microspheres with surface‐grafted polymer chains were employed in the preparation of polymer‐microsphere‐supported palladium composite particles. The composite particles were then studied by transmission electron microscopy and X‐ray diffraction. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 936–940, 2003     

Star graft copolymer via grafting‐onto strategy using a comb!ination of reversible addition–fragmentation chain transfer arm‐first technique and aldehyde–aminooxy click reaction

A facile synthetic pathway to a multi‐arm star graft polymer has been developed via a grafting‐onto strategy using a combination of a reversible addition–fragmentation chain transfer (RAFT) arm‐first technique and aldehyde–aminooxy click reaction. A star backbone bearing aldehyde groups was prepared by the RAFT copolymerization of acrolein (Ac), an existing commercial aldehyde‐bearing monomer, with styrene (St), followed by crosslinking of the resultant poly(St‐co‐Ac) macro‐RAFT agent using divinylbenzene. The aldehyde groups on the star backbone were then used as clickable sites to attach poly(ethylene glycol) (PEG) side chains via the click reaction between the aldehyde groups and aminooxy‐terminated PEG, leading to a structurally well‐defined star graft copolymer with arms consisting of poly(St‐co‐Ac) as backbone and PEG as side chains. Crystalline morphology and self‐assembly in water of the obtained star graft copolymer were also investigated. Opportunities are open for the star graft copolymer to form either multimolecular micelles or unimolecular micelles via control of the number of grafted PEG side chains. © 2013 Society of Chemical Industry     

Novel multimonomer‐grafted polypropylene preparation and application in polypropylene/poly(vinyl chloride) blends

A novel grafted polymer was prepared in one step through free‐radical melt grafting in a single‐screw extruder. It was shown that the addition of styrene (St) to the melt‐grafting system as a comonomer could significantly enhance the grafting degree of methyl methacrylate (MMA) onto polypropylene (PP) and reduce the degradation of the PP matrix by means of Fourier transform infrared and melt flow rate testing, respectively. Then, the potential of using multimonomer‐grafted PP, which was designated PP‐g‐(St‐co‐MMA), as the compatibilizer in PP/poly(vinyl chloride) (PVC) blends was also examined. In comparison with PP/PVC blends, the average size of the dispersed phase was greatly reduced in grafted polypropylene (gPP)/PVC blends because of the addition of the PP‐g‐(St‐co‐MMA) graft copolymer. The tensile strength of the gPP/PVC blends increased significantly, and the impact strength was unchanged from that of the pure PP/PVC blends. The results of differential scanning calorimetry and scanning electron microscopy suggested that the compatibility of the PP/PVC blends was improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Surface functionalization of Si3N4 nanoparticles by graft polymerization of glycidyl methacrylate and styrene

To improve dispersibility and interfacial interaction of nano‐Si₃N₄ particles in epoxy‐based composites, graft of glycidyl methacrylate (GMA) and styrene (St)/GMA onto the nanoparticles' surface was carried out in terms of emulsion polymerization method. The grafting polymers proved to be chemically attached to the nanoparticles via the double bonds introduced during the coupling agent pretreatment. The factors affecting the graft parameters, such as monomer concentration, initiator consumption, reaction time, etc., were investigated. It was shown that higher concentrations of monomer and initiator are favorable for the graft polymerization. When St/GMA was employed as the grafting monomer, the nanoparticles were found to play the role of polymerization loci. The grafted nanoparticles exhibit greatly improved dispersibility in cured epoxy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 992–999, 2006     

聚合物接枝纳米碳纤维/聚苯乙烯复合材料的制备与力学性能研究

采用自由基聚合方法,在纳米碳纤维(CNF)表面接枝聚丙烯酸正丁酯(PnBA)和聚苯乙烯(PS),利用接枝的嵌段聚合物作为大分子偶联剂制备CNF/PS复合材料。红外傅里叶变换光谱(FT-IR)研究表明,嵌段聚合物PnBA-b-PS被成功地接枝到CNF表面。扫描电子显微镜(SEM)和力学性能测试结果显示,CNF与PS复合材料界面结合得到改善,力学性能明显提高。     

Preparation and characterization of polystyrene/titanium dioxide composite particles containing organic ultraviolet‐stabilizer groups

Polystyrene/titanium dioxide (TiO₂) composite particles containing organic ultraviolet (UV)‐stabilizer groups were prepared by the emulsion copolymerization of styrene and 2‐hydroxy‐4‐(3‐methacryloxy‐2‐hydroxylpropoxy)benzophenone with sodium sulfopropyl lauryl maleate as a surfactant in the presence of rutile TiO₂ modified with 3‐(trimethoxysilyl) propyl methacrylate, and the product was poly[styrene‐co‐sodium sulfopropyl lauryl maleate‐co‐2‐hydroxy‐4‐(3‐methacryloxy‐2‐hydroxylpropoxy) benzophenone] [poly(St‐co‐M12‐co‐BPMA)]/TiO₂ composite particles. The structures of the composite particles were characterized with Fourier transform infrared spectroscopy, ultraviolet–visible (UV–vis) absorption spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. The Fourier transform infrared and UV–vis measurements showed that poly(St‐co‐M12‐co‐BPMA) was grafted from the surface of TiO₂, and this copolymer possessed a high absorbance capacity for UV light, which is very important for improving the UV resistance of polystyrene. The thermogravimetric analysis measurements indicated that the percentage of grafting and the grafting efficiency could reach 513.9 and 59.9%, respectively. The differential scanning calorimetry measurement indicated that the glass‐transition temperature of the poly(St‐co‐M12‐co‐BPMA)/TiO₂ composite particles was higher than that of poly (St‐co‐M12‐co‐BPMA).These research results are very important for preparing polystyrene with high UV resistance. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and enhanced swelling properties of a guar gum-based superabsorbent composite by the simultaneous introduction of styrene and attapulgite

In current study, a series of novel guar gum-graft-poly(sodium acrylate-co-styrene)/attapulgite (GG-g-P(NaA-co-St)/APT) superabsorbent nanocomposites were prepared by the simultaneous graft copolymerization of partially neutralized acrylic acid (NaA), styrene (St) and attapulgite (APT) onto natural guar gum (GG), using ammonium persulfate (APS) as the initiator and N,N'-methylene-bis-acrylamide (MBA) as the crosslinking agent. Fourier Transform Infrared (FTIR) and ultravoilet (UV) spectra confirmed that NaA and St had been grafted onto GG backbones and APT participated in the polymerization reaction. The incorporation of St and APT clearly improved the surface porous morphology of the composites as exhibited by Filed Emission Scanning Electron Microscopy (FESEM). The effect of St and APT on the swelling properties and the swelling kinetics of the developed nanocomposite was investigated. Results showed that the simultaneous incorporation of proper amount of hydrophobic co-monomer St and inorganic nano-scale APT not only obviously enhanced the swelling capacity but highly improved the swelling rate, and the nanocomposite showed better salt-resistant capability and excellent pH-stability in various pH solutions.     

Grafting polymers onto carbon black surface by trapping polymer radicals

Polystyrene, poly(styrene-co-maleic anhydride), poly[styrene-co-(4-vinylpyridine)] and poly(4-vinylpyridine) with well-defined molecular weights and polydispersities were synthesized using 4-hydroxyl-2,2,6,6-tetramethylpiperidin-1-oxyl (HTEMPO)-mediated radical polymerization initiated by azobisisobutyronitrile or benzoyl peroxide. The resultant polymers were grafted onto carbon black surface through a radical trapping reaction at 130 °C in DMF. ¹H NMR, TGA, TEM, AFM, DSC and dynamic light scattering were used to characterize the carbon black grafted with polymers. It was found that the carbon black grafted with polystyrene and poly(styrene-co-maleic anhydride) could be dispersed in THF, chloroform, dichloromethane, DMF, etc., and the carbon black grafted with poly(4-vinylpyridine) and poly[styrene-co-(4-vinylpyridine)] could be well dispersed in ethanol.     

Grafted stock synthesis of ABS at the ultimate high ratio of polybutadiene to poly(styrene‐co‐acrylonitrile)

This study describes the emulsion grafting of styrene and acrylonitrile onto 60–70% polybutadiene (PB), in the presence or absence of tert‐dodecanetiol as a chain transfer reagent with a radical initiator, and the properties of the obtained grafted stock. There was no significant difference in terms of effect of the initiation mode on the grafting efficiency resulting from the high grafting reactivity of PB. However, the grafted stock with 70% PB prepared in the presence of tert‐dodecanetiol and the adequate selection of an initiation system gave a homogeneous dispersion of the PB particles into poly(styrene‐co‐acrylonitrile) (SAN) matrix. The initiation system involves tert‐butyl peroxylaurate, tert‐butyl peroxyacetate, and tert‐butyl peroxyisopropylcarbonate coupled with ferrous sulfate. The efficient coverage of the SAN grafted layer around 70% PB particles was observed by TEM to eventually give excellent impact resistance, high surface gloss, and good thermal resistance. The absence of tert‐dodecanetiol resulted in a toughness reduction of ABS. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3462–3470, 2001     

A novel route for the synthesis of poly(2-hydroxyethyl methacrylate-co-methyl methacrylate) grafted titania nanoparticles via ATRP

A new method is presented for grafting poly(2-hydroxyethyl methacrylate-co-methyl methacrylate) (P(HEMA-co-MMA)) chains from the surface of TiO₂ nanoparticles via atom transfer radical polymerization (ATRP). First, the ATRP initiators were immobilized onto the TiO₂ surface by using 3-aminopropyltriethoxysilane coupling agent and 2-bromoisobutyryl bromide. Then the copolymerization of 2-hydroxyethyl methacrylate with methyl methacrylate was initiated and propagated on the TiO₂ surface by ATRP. The resulting composite nanoparticles were characterized by means of XPS, FT-IR, ¹H NMR, GPC and TGA. The results indicated that the grafting of copolymer chains from the TiO₂ surface was successful. This method opens up new avenues for the preparation of TiO₂-polymer nanocomposites.     

Synthesis and characterization of functionalized syndiotactic polystyrene copolymers

Functionalized syndiotactic polystyrene copolymers were synthesized and characterized. The syndiotactic polystyrene copolymers, poly(styrene‐co‐4‐methylstyrene) (sPSMS), were prepared by styrene with 4‐methylstyrene with a metallocene/methylaluminoxane catalyst. In addition, grafted copolymers, chemically grafted with isoprene onto an sPSMS backbone [poly(styrene‐co‐4‐methylstyrene)‐g‐polyisoprene (sPSMS‐g‐PIP)] were synthesized by anionic grafting polymerization with a metallation reagent. In this study, we also examined the effect of the degree of functionalization (epoxidation) on the polymer structure of the sPSMS‐g‐PIP copolymers. Experimental results indicate that the crystallinity of the sPSMS‐g‐PIP copolymer was lower than that of the ungrafted sPSMS copolymer. Moreover, the epoxy‐containing sPSMS‐g‐PIP copolymer effectively increased the thermal stability more than did the sPSMS‐g‐PIP copolymer alone. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1038–1045, 2002