Synthesis and characterization of Sr2+ and Mg2+ doped LaGaO3 by co-precipitation method followed by hydrothermal treatment for solid oxide fuel cell applications

In the present study, LSGM (La_0.8Sr_0.2Ga_0.8Mg_0.2O_2.8) powder has been synthesized using precipitation route followed by hydrothermal treatment. Quantitative phase analyses of different powders, have been done by Rietveld analyses of the XRD data and they reveal formation of single phase orthorhombic LSGM at 1400 °C, 8 h. Morphology of the calcined powder and microstructure of the sintered pellets are observed by transmission electron microscope (TEM) and scanning electron microscope (SEM), respectively. Thermal analysis has been carried out to find out the thermal expansion co-efficient. Successive electrical characterization of the 99% dense sintered pellet has been done by impedance spectroscopic analysis. The diffused semicircles observed in the Nyquist plots have been simulated as (RQ)(RQ) circuit and the total ionic conductivity obtained is found to be the highest for LSGM synthesized by similar routes.     

Preparation and luminescent properties of Tb3+ doped Y2O2SO4 microflakes

Abstract

Tb³⁺ doped Y₂O₂SO₄ (Y₂O₂SO₄:Tb³⁺) microflakes were prepared by a combination method of electrospinning and calcination. The two-dimensional microflakes had smooth surface and high radial/axial ratio. Crystal structures of the Y₂O₂SO₄:Tb³⁺ microflakes resulted in layer by layer growth in axial direction. A possible formation mechanism was proposed on the basis of experimental results, which indicated that poly(vinyl pyrrolidone) played the role of the nanostructure directing template and revealed the growth priority in radial direction. The microflakes showed a favourable fluorescent property symbolised by the characteristic green emission (541 nm) resulting from the ⁵D₄→⁷F₅ transition of Tb³⁺ ions under 229 nm ultraviolet excitation. The maximum intensity of Tb³⁺ emission of the Y₂O₂SO₄:Tb³⁺ microflakes was 2·3 times stronger than that of the Y₂O₂SO₄:Tb³⁺ bulk powders with the same doping concentration.     

Electrical properties and AC degradation characteristics of low voltage ZnO varistors doped with Nd2O3

The electrical properties and degradation characteristics of low voltage ZnO varistors were investigated as a function of Nd₂O₃ content. The varistor ceramics with 0.03 mol% Nd₂O₃ sintered at 1250 °C were far more densified than those with 0.06, 0.09 and 0.12 mol% Nd₂O₃. The addition of Nd₂O₃ to the low voltage ZnO varistors greatly improved the current–voltage characteristics; the nonlinear coefficient of varistors increase from 12.2 to 34.6 with increasing Nd₂O₃ content. The samples with 0.03 mol% Nd₂O₃ showed excellent stability due to high density and relatively good V–I characteristics, with the nonlinear coefficient of 22.5 and the leakage current of 9.6 μA. Their variation rate of varistor voltage and nonlinear coefficient and leakage current were −4.7%, −5.4%, 18.3%, respectively, under AC degradation stress (1.0 V_1 mA/125 °C/24 h).     

Efficient perovskite solar cells based on low-temperature solution-processed (CH3NH3)PbI3 perovskite/CuInS2 planar heterojunctions

In this work, the solution-processed CH₃NH₃PbI₃ perovskite/copper indium disulfide (CuInS₂) planar heterojunction solar cells with Al₂O₃ as a scaffold were fabricated at a temperature as low as 250°C for the first time, in which the indium tin oxide (ITO)-coated glass instead of the fluorine-doped tin oxide (FTO)-coated glass was used as the light-incidence electrode and the solution-processed CuInS₂ layer was prepared to replace the commonly used TiO₂ layer in previously reported perovskite-based solar cells. The influence of the thickness of the as-prepared CuInS₂ film on the performance of the ITO/CuInS₂(n)/Al₂O₃/(CH₃NH₃)PbI₃/Ag cells was investigated. The ITO/CuInS₂(2)/Al₂O₃/(CH₃NH₃)PbI₃/Ag cell showed the best performance and achieved power conversion efficiency up to 5.30%.     

Oxidative coupling of methane catalyzed by Li, Na and Mg doped BaSrTiO3

The XBaSrTiO₃ (X = Li, Na, Mg) with perovskite structure was prepared by impregnation of LiCl, NaCl or MgCl₂ solution on BaSrTiO₃ (BST) surface. The products were characterized with XRD, SEM, UV, FT-IR and Raman spectroscopy. Determination of band gap, conduction and basicity of the prepared catalysts revealed that NaBST exhibits the lowest band gap and the most conduction and basicity. The catalytic performances of XBSTs for the oxidative coupling of methane (OCM) in a tubular continuous flow reactor were evaluated. The NaBST showed the maximum catalytic effect on methane conversion (47%), C₂₊ selectivity (51%) and ethylene yield (24%) at the temperature of 800 °C.     

Crystal structure refinement and hydration behaviour of doped tricalcium aluminate

In this paper analytical evidence on crystal structure and hydration behaviour of C₃A solid solutions with MgO, SiO₂, Fe₂O₃, Na₂O and K₂O is given. Samples were prepared using an innovative sol-gel process as precursor, examined by X-ray powder diffraction, infra-red spectroscopy and the crystal structure was refined by the Rietveld method. A significant shift of lattice parameters was found for C₃A solid solutions with SiO₂, Fe₂O₃ or Na₂O but only minor changes were detected for K₂O. The hydration of C₃A solid solutions in the absence of CaSO₄ was accelerated for samples doped with SiO₂ or K₂O and it was retarded in the case of MgO, Fe₂O₃ or Na₂O. The hydration in the presence of CaSO₄ was accelerated when C₃A was doped with K₂O or Na₂O, whereas Fe₂O₃ strongly retarded the hydration. The doping with SiO₂ nearly had no influence on the hydration, the effect of MgO was not straight forward.     

铬酸酐掺杂V2O5制备高红外反射率氧化铬绿颜料

研究了铬酸酐热分解制备高性能红外反射氧化铬绿颜料,在优化现有铬酸酐热分解工艺的基础上,详细探讨了掺杂制备红外反射氧化铬绿颜料的工艺条件和相关机理。借助UV-vis-NIR、FT-IR、SEM、XRD和CIE-L^*a^*b^*等手段发现:在铬酸酐热分解过程中,不同的热分解温度导致粒径变化,从而影响红外反射率;优化的制备工艺条件(热分解温度1250℃、热分解时间0.5 h)下,氧化铬绿的红外反射率达到90%。在掺杂过程中,V₂O₅的添加可使氧化铬绿的最高红外反射率达到98%。随着V₂O₅添加量的增加,红外反射率先增加后减少;当V/Cr摩尔比为0.004时,红外反射率、电导率、介电常数都达到极值,三者呈现一致的规律性变化。初步机理探索表明,氧化铬本征导电类型为空穴导电,掺杂V₂O₅以后导电类型发生改变,伴随着电阻率的变化,氧化铬吸收和反射光子能力改变,从而影响红外反射性能。     

Scandium ion doped yttrium oxide transparent ceramic from nitrate alanine microwave combustion synthesized nanopowders

One atomic percent Neodymium ion doped Yttrium oxide, with 25 at% scandium ion (Nd_0.02Sc_0.5Y_1.48O₃), was synthesized by nitrate alanine microwave gel combustion followed by calcinations at 1000 °C for 2 h. Phase purity of nanopowder was characterized by X-Ray Diffraction (XRD). Neodymium and scandium ion doping was confirmed by cell parameter calculation and Scanning Electron Microscope-Electron Dispersive X-ray (SEM-EDX) analysis. Particles with size range 25–35 nm with close to spherical shape were obtained as observed by Transmission Electron Microscopy (TEM). Powder on compaction followed by vacuum sintering at 1765 °C for 40 min led to the formation of ceramic with 76% transmission at 2500 nm compared to translucent ceramic obtained without scandium ion doping. This indicates formation of highly sinterable neodymium doped yttrium oxide nanopowders by nitrate alanine microwave gel combustion route with scandium ion additive. Further the absorption and emission bands of Nd_0.02Sc_0.5Y_1.48O₃ are inhomogeneously broadened and fluorescence lifetime is longer than Nd_0.02Y_1.98O₃.     

Interface structure and wetting behaviour of Cu/Ti3SiC2 system

Wetting behaviour of a Cu/Ti₃SiC₂ system was investigated by the sessile drop technique under a vacuum atmosphere. Contact angles between Cu and Ti₃SiC₂ changed from 95 to 15° as temperatures increased from 1089 to 1270°C. Two distinct reaction layers consisting of different contents of Cu, TiC_x, Ti₃SiC₂ and Cu_xSi_y intermetallics were formed at the interface of Cu and Ti₃SiC₂. The formation of the interface layers contributes to the improvement of the wettability of the system. The dissolution of Si from theTi₃SiC₂ into the molten Cu at high temperature plays a dominant role in the wetting behaviour of Cu/Ti₃SiC₂ systems.     

Metal oxide catalysts for DME steam reforming: Ga2O3 and Ga2O3–Al2O3 catalysts

The steam reforming of dimethyl ether (DME) was performed on Ga₂O₃–Al₂O₃ mixed oxides prepared by sol–gel method. Ga₂O₃ significantly affects the catalytic performance with respect to the DME conversion and H₂ yield. The catalytic activity increases with the Ga concentration in Ga₂O₃–Al₂O₃ mixed oxides. It is very interesting that without the aid of an additional transition metal component, Ga₂O₃ and Ga₂O₃ containing Al₂O₃ mixed oxide system exhibit good activity in the reforming reaction. To the best of our knowledge, this is the first report that reveals the reforming ability of Ga₂O₃ for the production of H₂ from DME and/or methanol.     

Changes in Ba Phases in BaO/Al2O3 upon Thermal Aging and H2O Treatment

The effects of thermal aging and H₂O treatment on the physicochemical properties of BaO/Al₂O₃ (the NO_x storage component in the lean NO_x trap systems) were investigated by means of X-ray diffraction (XRD), BET, TEM/EDX and NO₂ TPD. Thermal aging at 1000 °C for 10 h converted dispersed BaO/BaCO₃ on Al₂O₃ into low surface area crystalline BaAl₂O₄. TEM/EDX and XRD analysis showed that H₂O treatment at room temperature facilitated a dissolution/reprecipitation process, resulting in the formation of a highly crystalline BaCO₃ phase segregated from the Al₂O₃ support. Crystalline BaCO₃ was formed from conversion of both BaAl₂O₄ and a dispersed BaO/BaCO₃ phase, initially present on the Al₂O₃ support material after calcinations at 1000 and 500 °C, respectively. Such a phase change proceeded rapidly for dispersed BaO/BaCO₃/Al₂O₃ samples calcined at relatively low temperatures with large BaCO₃ crystallites observed in XRD within 10 min after contacting the sample with water. Significantly, we also find that the change in barium phase occurs even at room temperature in an ambient atmosphere by contact of the sample with moisture in the air, although the rate is relatively slow. These phenomena imply that special care to prevent the water contact must be taken during catalyst synthesis/storage, and during realistic operation of Pt/BaO/Al₂O₃ NO_x trap catalysts since both processes involve potential exposure of the material to CO₂ and liquid and/or vapor H₂O. Based on the results, a model that describes the behavior of Ba-containing species upon thermal aging and H₂O treatment is proposed.     

Dehydrogenation of ethylbenzene over TiO2-Fe2O3 and ZrO2-Fe2O3 mixed oxide catalysts

The mixed metal oxides TiO₂-Fe₂O₃ and ZrO₂-Fe₂O₃ were examined as potential catalysts for the dehydrogenation reaction of ethylbenzene. The acidic and basic properties and surface area, pore volume and pore size distribution of these catalysts were measured. The catalytic activities can be correlated very well with the surface area and the acidity and basicity of ZrO₂-Fe₂O₃ catalysts. However, for TiO₂-Fe₂O₃ catalysts, the surface area, the amount of acidic and basic sites and TiFe₂O₅ crystallinity are all important factors affecting the catalytic activities for ethylbenzene dehydrogenation. A synergistic effect was found for the TiO₂-Fe₂O₃ and ZrO₂-Fe₂O₃ catalyst system and also for the TiO₂-Fe₂O₃-ZrO₂ system, i.e. the activities of these catalysts can be ranked in the following order: TiO₂-Fe₂O₃-ZrO₂>TiO₂-Fe₂O₃ >ZrO₂>Fe₂O₃>TiO₂. Meanwhile, all of these catalysts showed higher activities than the conventional potassium-promoted iron catalysts.     

Effect of Y2O3 and Er2O3 co-dopants on phase stabilization of bismuth oxide

Bi₂O₃ compositions were prepared to investigate the effect of rare earth metal oxides as co-dopants on phase stability of bismuth oxide. Compositions containing 9-14 mol% of Y₂O₃ and Er₂O₃ were synthesized by solid state reaction. The structural characterization was carried out using X-ray powder diffraction. The XRD results show that the samples containing 12 and 14 mol% total dopants had cubic structure, whereas the samples with lower dopant concentrations were tetragonal. Comparing the lattice parameters of the cubic phases of (Bi₂O₃)_0.88(Y₂O₃)_0.06(Er₂O₃)_0.06 and (Bi₂O₃)_0.86(Y₂O₃)_0.07(Er₂O₃)_0.07 revealed that lattice parameter decreases by increasing the dopant concentration. The XRD pattern and the powder density results indicated the formation of solid solution in the studied systems. After annealing samples with cubic phase at 600 °C for various periods of time, phase transformation to tetragonal and rhombohedral occurs.     

ZnO含量对Tb3+掺杂ZnO-B2O3-SiO2玻璃余辉性能及光致变色的影响

选择制备了Tb3+掺杂的不同ZnO含量、组成为xZnO- [(100-x)/2]B2O3-[(100-x)/2]SiO2(x=55,60, 65,70)的ZBS玻璃.并通过光致发光光谱、余辉衰减曲线、热释光谱以及紫外-可见吸收光谱系统地研究了该玻璃系统的余辉发光特性和光致变色现象.随着ZnO含量的增加,基质玻璃中Tb3+的5D4→7F5跃迁对应的余辉发光强度增大、其寿命变长.热释光谱表明ZnO含量的提高没有形成新的陷阱,而是增加了陷阱的浓度导致余辉寿命增长.光致变色实验发现:不同样品在紫外照射后其变色程度随ZnO含量增加而增加.玻璃的变色主要由色心引起,本研究中ZnO含量的增加使玻璃基质中Zn离子相关的氧空位浓度增大,从而在紫外光照射后,具有不同陷阱能级深度的色心浓度也相应增加,最终导致了所观察到的余辉特性和光致变色特性的变化结果.另外,通过对不同温度热处理后样品的透过率变化实验分析认为,陷阱能级浅的色心对长余辉有贡献,能级深的将稳定存在于基质中,并对光致变色有较大贡献.     

Preparation and tribological behaviour of laminated Ti3AlC2 crystals as additive in base oil

Abstract

Laminated ternary compound Ti₃AlC₂ crystals were synthesised by pressureless sintering the mixture powders of 3Ti/1·1Al/1·8C, 3Ti/1Al/1·8C/0·2Sn, 1Ti/1·8TiC/1Al and 1Ti1·8TiC1Al0·1Sn at 1400°C with preliminary liquid magnetic stirring mixing. The X-ray diffraction results indicate that Ti₃AlC₂ prepared from 3Ti/1Al/1·8C/0·2Sn has the highest purity, and the addition of appropriate Sn favours the synthesis of high purity Ti₃AlC₂. Scanning electron microscopy images show that Ti₃AlC₂ samples exhibit lamellar-like microstructure with thickness of ～100 nm. The tribological properties of Ti₃AlC₂ as an additive in 100SN base oil were evaluated with a ball on disc tester. The results show that the Ti₃AlC₂ additives exhibited good friction reduction and wear resistance at 5 wt-% concentration. Under determinate conditions, the base oil containing 5 wt-% Ti₃AlC₂ samples presented good tribology performance under the load of 15 N. The improved tribological properties of the Ti₃AlC₂ samples could be attributed to the formation of tribofilm in friction process.     

Preparation and characterization of 10 mol% Gd doped CeO2 (GDC) electrolyte for SOFC applications

Ceria-based materials are prospective electrolytes for low and intermediate temperature solid oxide fuel cells. In the present work, fully dense CeO₂ ceramics doped with 10 mol% gadolinium (Gd_0.1Ce_0.9O_1.95, GDC) have been prepared with a Pechini method. Characterization studies were realized with thermo-gravimetric analysis (TGA), differential thermal analysis (DTA), mass spectroscopy (MS), high temperature FT-IR (HT-FTIR) and X-ray diffraction analysis (XRD). A single-phase with a fluorite type structure was found to form at a relatively low calcination temperature of 500 °C. Dense GDC pellets having 98% of the relative density were obtained at sintering temperature of 1400 °C/6 h, which gave significantly higher total ionic conductivity of 3.4×10⁻² S cm⁻¹ at 500 °C in air. The present work showed that the Pechini method is a relatively low-temperature preparation technique to synthesize Gd_0.1Ce_0.9O_1.95 powders that provided high sinterability and good ionic conductivity.     

Color-tunable properties of Eu3+- and Dy3+-codoped Y2O3 phosphor particles

Rare-earth phosphors are commonly used in display panels, security printing, and fluorescent lamps, and have potential applications in lasers and bioimaging. In the present study, Eu³⁺- and Dy³⁺-codoped uniform-shaped Y₂O₃ submicron particles were prepared using the urea homogeneous precipitation method. The structure and morphology of the resulting particles were characterized by X-ray diffraction, field emission scanning electron microscope, and field emission transmission electron microscope, whereas their optical properties were monitored by photoluminescence spectroscopy. The room-temperature luminescence color emission of the synthesized particles can be tuned from red to yellow by switching the excitation wavelength from 254 to 350 nm. The luminescence intensities of red and yellow emissions could be altered by varying the dopant concentration. Strong quenching was observed at high Eu³⁺ and Dy³⁺ concentrations in the Y₂O₃ host lattice.     

Accommodation of impurities in α-Al2O3, α-Cr2O3 and α-Fe2O3

Atomic scale computer simulation was used to predict the mechanisms and energies associated with the accommodation of aliovalent and isovalent dopants in three host oxides with the corundum structure. Here we consider a much more extensive range of dopant ions than has previously been the case. This enables a rigorous comparison of calculated mechanism energetics. From this we predict that divalent ions are charge compensated by oxygen vacancies and tetravalent ions by cation vacancies over the full range of dopant radii. When defect associations are included in the model these conclusions remain valid. At equilibrium, defects resulting from extrinsic dopant solution dominate intrinsic processes, except for the largest dopant cations. Solution reaction energies increase markedly with increasing dopant radius. The behaviour of cluster binding energies is more complex.     

Nanoindentation behaviour of nano BiFeO3

Bismuth ferrite (BiFeO₃) is a unique magnetoelectric multiferroic that exhibits the coexistence of ferroelectricity and antiferromagnetism at room temperature. This unique combination of properties has pumped a huge surge in current research on BiFeO₃ as a future material for very important technological applications such as magnetic detectors and as an active layer in magnetoelectric memories. For such applications involving miniaturized components and devices, it is essentially important to have an idea of the mechanical integrity of the system at the scale of the microstructure. In spite of the wealth of the literature, however, the attempt to evaluate the mechanical integrity of nano BiFeO₃ at a scale comparable with the local microstructural length scale was almost non-existent. Here we report, possibly for the first time the nanoindentation behaviour of a sol-gel process derived nano BiFeO₃ having particle size of 5-25 nm. The nanoindentation studies were conducted at 100-1000 μN loads on a green pellet annealed at a low temperature of only 300 °C to avoid particle coarsening. The results showed interesting dependence of nanohardness and Young's modulus on the nanoindentation load which could be explained in terms of elastic recovery and plastic deformation energy concepts.     

Effect of In, Ce and Bi dopings on sintering and dielectric properties of Ba(Zn1/3Nb2/3)O3 ceramics

In, Ce and Bi doped Ba(Zn_1/3Nb_2/3)O₃ (BZN) ceramics were prepared by conventional mixed oxide technique. In doping between 0.2 and 4.0 mol% increased the density of BZN at 1300 °C, Ce doping caused a decrease in density at 1250 °C. Levels of Bi₂O₃ up to 1.0 mol% had negative effect on densification, while high level doping could significantly improve the densification of the specimens. XRD of the samples indicated that In, Ce and Bi doping resulted in single phase formation at all concentrations, except 0.5 mol% Bi. SEM of Bi doped BZN indicated only single phase structure and Ce doping even at 0.2 mol% gave some secondary phases. In and Ce doping increased the dielectric constant from 41 to around 66 at 1 MHz. Bi doping decreased the dielectric constant to about 37 at 0.2 mol%, and then higher doping led to dielectric constant to increase to about 63.