Grafting copolymerization of maleic anhydride onto styrene‐butadiene‐styrene block copolymer through solvothermal process

The grafting copolymerization of maleic anhydride (MAH) onto styrene‐butadiene‐styrene terpolymer (SBS) was carried out through a new synthesis method––solvothermal synthesis. Infrared (IR) spectra and solid state ¹³C‐NMR confirmed that maleic anhydride was successfully grafted onto the SBS backbone. The effects of different solvents, different initiators and their concentration, the amount of MAH, SBS concentration, and reaction time on the graft degree were evaluated, and the optimal conditions were obtained. Results indicated that the grafting reaction of MAH onto SBS through solvothermal method can be carried out in both good solvents and poor solvents, which are much different from the traditional solution grafting method, and high grafting degree can be obtained in good solvents. Finally, we also compared the grafting degree (GD) prepared by the solvothermal method with that by the melt grafting method and solution grafting method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5274–5279, 2006     

Preparation and properties of bitumen modified with the maleic anhydride grafted styrene‐butadiene‐styrene triblock copolymer

A procedure to improve the properties of styrene‐butadiene‐styrene (SBS) copolymer modified bitumen by grafting of maleic anhydride (MAH) onto SBS in the presence of benzoyl peroxide (BPO) as initiator was proposed. The effects of the grafting degree (GD) on the properties of modified bitumen were investigated. FTIR spectroscopy was employed to verify the grafting of MAH onto SBS. The GD of MAH onto SBS was determined by a back titration procedure. To assess the effects of the GD of grafted SBS on properties of modified bitumen, the softening point, penetration, ductility, elastic recovery, penetration index, viscosity, storage stability, and dynamic shear properties were tested. Experimental results indicated that the SBS grafted with maleic anhydride (SBS‐g‐MAH) copolymer was successfully synthesized by solvothermal method, and different GD of the SBS‐g‐MAH was obtained by control the MAH concentration. The GD of the MAH onto SBS has great effect on the rheological properties of the modified bitumen, and the high temperature performance and storage stability of modified bitumen were improved with the GD of the MAH onto SBS increasing. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Mechanical and piezo‐resistive properties of styrene–butadiene–styrene copolymer covalently modified with graphene/styrene–butadiene–styrene composites

As novel piezoelectric materials, carbon‐reinforced polymer composites exhibit excellent piezoelectric properties and flexibility. In this study, we used a styrene–butadiene–styrene triblock copolymer covalently grafted with graphene (SBS‐g‐RGO) to prepare SBS‐g‐RGO/styrene–butadiene–styrene (SBS) composites to enhance the organic solubility of graphene sheets and its dispersion in composites. Once exfoliated from natural graphite, graphene oxide was chemically modified with 1,6‐hexanediamine to functionalize with amino groups (GO–NH₂), and this was followed by reduction with hydrazine [amine‐functionalized graphene oxide (RGO–NH₂)]. SBS‐g‐RGO was finally obtained by the reaction of RGO–NH₂ and maleic anhydride grafted SBS. After that, X‐ray diffraction, X‐ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, and other methods were applied to characterize SBS‐g‐RGO. The results indicate that the SBS molecules were grafted onto the graphene sheets by covalent bonds, and SBS‐g‐RGO was dispersed well. In addition, the mechanical and electrical conductivity properties of the SBS‐g‐RGO/SBS composites showed significant improvements because of the excellent interfacial interactions and homogeneous dispersion of SBS‐g‐RGO in SBS. Moreover, the composites exhibited remarkable piezo resistivity under vertical compression and great repeatability after 10 compression cycles; thus, the composites have the potential to be applied in sensor production. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46568.     

Grafting of N‐carbamyl maleamic acid onto a styrene–butadiene–styrene copolymer

A styrene–butadiene–styrene block copolymer (SBS) was functionalized with N‐carbamyl maleamic acid (NCMA) using two peroxide initiators with the aim of grafting polar groups onto the molecular chains of the polymer. The influence of the concentration of benzoyl peroxide (BPO) and 2,5‐dimethyl, 2,5‐diterbuthylperoxihexane (DBPH) was studied. The concentration of peroxy groups ranged between 0.75 and 6 × 10^?4 mol % while the concentration of NCMA was constant at 1 wt %. The reaction temperature was chosen according to the type of peroxide employed, being 140°C for BPO and 190°C for DBPH. FTIR spectra confirmed that NCMA was grafted onto the SBS macromolecules. It was found that the highest grafting level was achieved at a concentration of peroxy groups of about 3 × 10^?4 mol %. Contact angle measurements were used to characterize the surface of the SBS and modified polymers. The contact angle of water drops decreased with the amount of NCMA grafted from 95°, the one corresponding to the SBS, to about 73°. T‐peel strength of polymer/polyurethane adhesive/polymer joints made with the modified polymers was larger than those prepared with the original SBS. The peel strength of SBS modified with 1.5 and 3 × 10^?4 mol % of peroxy groups from BPO were five times larger than that of the original SBS. The materials modified using BPO showed peel strengths higher than the ones obtained with DBPH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4468–4477, 2006     

Amphiphilic styrene–butadiene–styrene triblock copolymer grafted with polyoxyethylene

A styrene–butadiene–styrene triblock copolymer (SBS) was grafted with polyoxyethylene via a ring‐opening reaction of an epoxidized styrene–butadiene– styrene triblock copolymer (ESBS) with monocarboxylic‐group‐terminated methoxypoly(ethylene glycol) (CMPEG). The latter was prepared through the esterification of methoxypoly(ethylene glycol) with maleic anhydride. The optimum conditions for the preparation of the graft copolymer were studied. The graft copolymer was characterized with Fourier transform infrared spectrophotometry. Its water absorbency, oil absorbency, emulsifying property, phase‐transfer catalysis property in the Williamson solid–liquid reaction, and use as a compatibilizer in the blending of SBS with oil‐resistant chlorohydrin rubber (CHR) were also studied. The optimum conditions were a CMPEG/epoxy group molar ratio of 1.5, an N,N‐dimethyl aniline/ESBS concentration of 5 wt %, and an ESBS concentration of 12–14 g/100 mL at 75–80°C for 10 h. The polyoxyethylene content could reach 0.27 mmol/g. The graft copolymer absorbed a certain amount of water, fairly resisted kerosene, and possessed good emulsifying and phase‐transfer catalysis properties, both of which were enhanced with increasing polyoxyethylene graft content. The graft copolymer could be used as a compatibilizer for a blend of SBS and CHR. A 3 wt % concentration of the graft copolymer based on a 50/50 blend could increase both the tensile strength and ultimate elongation of the blend about 1.7 times. The blend behaved like an oil‐resistant thermoplastic elastomer. Scanning electron microscopy demonstrated the improved compatibility of the two components by the graft copolymer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Properties of acrylonitrile–butadiene–styrene/polycarbonate blends with styrene–butadiene–styrene block copolymer

The importance of alloys and blends has increased gradually in the polymer industry so that the plastics industry has moved toward complex systems. The main reasons for making polymer blends are the strengthening and the economic aspects of the resultant product. In this study, I attempted to improve compatibility in a polymer blend composed of two normally incompatible constituents, namely, acrylonitrile–butadiene–styrene (ABS) and polycarbonate (PC), through the addition of a compatibilizer. The compatibilizing agent, styrene–butadiene–styrene block copolymer (SBS), was added to the polymer blend in ratios of 1, 5, and 10% with a twin‐screw extruder. The morphology and the compatibility of the mixtures were examined by scanning electron microscopy and differential scanning calorimetry. Further, all three blends of ABS/PC/SBS were subjected to examination to obtain their yield and tensile strengths, elasticity modulus, percentage elongation, Izod impact strength, hardness, heat deflection temperature, Vicat softening point, and melt flow index. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2521–2527, 2004     

Effect of maleic anhydride grafted polybutadiene on the compatibility of polyamide 66/acrylonitrile‐butadiene‐styrene copolymer blend

The addition of maleic anhydride grafted polybutadiene (PB‐g‐MAH) can greatly improve the compatibility of polyamide 66 (PA66)/acrylonitrile‐butadiene‐styrene copolymer (ABS) blends. Unlike the commonly used compatibilizers in polyamide/ABS blends, PB‐g‐MAH is compatible with the ABS particles' core phase polybutadiene (PB), rather than the shell styrene‐acrylonitrile (SAN). The compatibility and interaction of the components in the blends were characterized by Fourier transform‐infrared spectra (FTIR), Molau tests, melt flow index (MFI), dynamic mechanical analyses (DMA), and scanning electron microscopic (SEM) observations. The results show that PB‐g‐MAH can react with the amino end groups in PA66 while entangle with the PB phase in ABS. In this way, the compatibilizer anchors at the interface of PA66/ABS blend. The morphology study of the fracture sections before and after tensile test reveals that the ABS particles were dispersed uniformly in the PA66 matrix and the interfacial adhesion between PA66 and ABS was increased significantly. The mechanical properties of the blends thus were enhanced with the improving of the compatibility. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Bulk modification of styrene–butadiene–styrene triblock copolymer with maleic anhydride

The bulk modification of SBS rubber with maleic anhydride in a mixing chamber of a Haake rheomixer was studied. The effect of temperature, maleic anhydride, and benzoyl peroxide concentrations on the grafting efficiency was evaluated. High grafting efficiency was achieved when the ratio of peroxide and maleic anhydride concentration was high. On the other hand, on this condition high insoluble fraction was generated. The addition of a diamine, 4,4′‐diaminediphenylmethane to the reaction mixture minimizes the amount of insoluble polymer. However, the grafted MAH content also decreases. The graft copolymer was characterized by infrared spectroscopy and the grafting extension was determined by titration. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2953–2960, 2002; DOI 10.1002/app.10355     

Effect of styrene–isoprene–styrene,styrene–butadiene–styrene,and styrene–butadiene–rubber on the mechanical,thermal, rheological,and morphological properties of polypropylene/polystyrene blends

The mechanical, thermal, rheological, and morphological properties of polypropylene (PP)/polystyrene (PS) blends compatibilized with styrene–isoprene–styrene (SIS), styrene–butadiene–styrene (SBS), and styrene–butadiene–rubber (SBR) were studied. The incompatible PP and PS phases were effectively dispersed by the addition of SIS, SBS, and SBR as compatibilizers. The PP/PS blends were mechanically evaluated in terms of the impact strength, ductility, and tensile yield stress to determine the influence of the compatibilizers on the performance properties of these materials. SIS‐ and SBS‐compatibilized blends showed significantly improved impact strength and ductility in comparison with SBR‐compatibilized blends over the entire range of compatibilizer concentrations. Differential scanning calorimetry indicated compatibility between the components upon the addition of SIS, SBS, and SBR by the appearance of shifts in the melt peak of PP toward the melting range of PS. The melt viscosity and storage modulus of the blends depended on the composition, type, and amount of compatibilizer. Scanning electron microscopy images confirmed the compatibility between the PP and PS components in the presence of SIS, SBS, and SBR by showing finer phase domains. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 266–277, 2003     

Synthesis and properties of novel amphiphilic sulfated ionomers by the ring‐opening reaction of an epoxidized styrene–butadiene–styrene triblock copolymer

A method for the synthesis of novel sulfated ionomer of styrene–butadiene–styrene triblock copolymer (SBS) was developed. SBS was first epoxidized by performic acid in the presence of a phase‐transfer catalyst; this was followed by a ring‐opening reaction with an aqueous solution of alkali salt of bisulfate. The optimum conditions for the ring‐opening reaction of the epoxidized SBS with an aqueous solution of KHSO₄ were studied. During the ring‐opening reaction, both phase‐transfer catalyst and ring‐opening catalyst were necessary to enhance the conversion of epoxy groups to ionic groups. The products were characterized with Fourier transform infrared spectrophotometry and transmission electron microscopy (TEM). After the potassium ions of the ionomer were substituted with lead ions, the lead sulfated ionomer exhibited dark spots under TEM. Some properties of the sulfated ionomer were studied. With increasing ionic groups or ionic potential of the cations, the water absorbency and emulsifying volume of the ionomer and the intrinsic viscosity of the ionomer solution increased, whereas the oil absorbency decreased. The sulfated ionomer possessed excellent emulsifying properties compared with the sulfonated SBS ionomer. The sodium sulfated ionomers in the presence of 10% zinc stearate showed better mechanical properties than the original SBS. When the ionomer was blended with crystalline polypropylene, a synergistic effect occurred with respect to the tensile strength. The ionomer behaved as a compatibilizer for blending equal amounts of SBS and oil‐resistant chlorohydrin rubber. In the presence of 3% ionomer, the blend exhibited much better mechanical properties and solvent resistance than the blend without the ionomer. SEM photographs indicated improved compatibility between the two components of the blend in the presence of the ionomer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Characterization of end‐functionalized styrene–butadiene–styrene copolymers and their application in modified asphalt

End amino, carboxylic acid, and hydroxyl functionalized styrene–butadiene–styrene (SBS) triblock copolymers were prepared with 1,5‐diazabicyclo[3.1.0]hexane, carbon dioxide, and epoxy ethane as capping agents, respectively. The effects of the end polar groups on the morphology and dynamic mechanical properties were investigated. Transmission electron microscopy images suggested that the group at the end of the polystyrene (PS) segment made the morphology of the PS domains disordered and incompact. Dynamic mechanical results showed that the storage and loss modulus increased after SBS was end‐functionalized. End amino and carboxylic acid groups improved the compatibility and storage stability of SBS‐modified asphalt. However, the effect of the end‐hydroxyl group on the improvement of the storage stability of SBS‐modified asphalt was not obvious. The differential scanning calorimetry analysis of SBS‐modified asphalt further showed that the compatibility and storage stability of SBS‐modified asphalt were improved by the attachment of amino or carboxylic acid groups through the anionic polymerization method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 8–16, 2007     

Photodegradation and stabilization of styrene–butadiene–styrene rubber

Photooxidative degradation and stabilization of a polystyrene–block–polybutadiene–block–polystyrene thermoplastic elastomer using a polychromatic UV light in air at 60°C has been studied by monitoring the appearance of the hydroxyl and carbonyl groups in Fourier transform infrared spectroscopy. The extent of photooxidative degradation in different samples has been compared. The rate of photooxidation was also estimated in the presence of different concentrations of 2,6‐di‐tert‐butyl‐4‐methylphenol [BHT], 2‐(2′‐hydroxy‐5′‐methylphenyl)benzotriazole [Tinuvin P] and tris(nonylphenyl) phosphite [Irgafos TNPP], and 1,2,2,6,6‐pentamethyl piperidinyl‐4‐acrylate was grafted onto the surface of the SBS film. The kinetic evolution of the oxidative reaction was determined. The morphological changes upon irradiation in the solution cast SBS films were studied by scanning electron microscopy. Based on the experimental data a suitable photooxidative degradation mechanism also has been proposed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1097–1102, 2000     

Styrene‐butadiene‐styrene copolymer compatibilized interfacial modified multiwalled carbon nanotubes with mechanical and piezoresistive properties

In this study, styrene‐butadiene‐styrene tri‐block copolymer/multiwalled carbon nanotubes (SBS/MWNTs) were prepared by means of a solution blending method. To enhance the compatibility between SBS and MWNTs, the SBS grafted MWNTs (SBS‐g‐MWNTs) were used to replace MWNTs. The MWNTs were chemically hydroxylated by the dissolved KOH solution with ethanol as solvent and then reacted with 3‐Aminopropyltriethoxysilane (APTES) to functionalize them with amino groups (MWNT‐NH₂). The SBS‐g‐MWNTs were finally obtained by the reaction of MWNT‐NH₂ and maleic anhydride grafted SBS (MAH‐g‐SBS). The SBS‐g‐MWNTs were characterized by X‐ray photoelectron spectroscopy (XPS), Fourier transform‐infrared spectroscopy (FT‐IR), transmission electron microscopy (TEM), scanning electron microscope (SEM), and thermogravimetric analysis (TGA). The results showed that the SBS molecules were homogeneously bonded onto the surface of the MWNTs, leading to an improvement of the mechanical and electrical properties of SBS/SBS‐g‐MWNTs composites due to the excellent interfacial adhesion and dispersion of SBS‐g‐MWNTs in SBS. A series of continuous tests were carried out to explore the electrical‐mechanical properties of the SBS/SBS‐g‐MWNTs composites. We found out that, near the percolation threshold, the well‐dispersed SBS/SBS‐g‐MWNTs composites showed good piezoresistive characteristics and small mechanical destructions for the development of little deformation under vertical pressure. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42945.     

Viscoelastic relaxation of styrene–butadiene–styrene block copolymers with different topological structures

The viscoelastic relaxation of linear styrene–butadiene–styrene triblock copolymer (l‐SBS) and star styrene–butadiene–styrene triblock copolymer (s‐SBS) with four arms were investigated with differential scanning calorimetry and dynamic rheological measurements. Three characteristic viscoelastic responses of l‐SBS and s‐SBS in the plot of the loss tangent (tan δ) and temperature at different frequencies (ω's), which corresponded to the relaxation of the polybutadiene (PB) block (peak I), the glass transition of the polystyrene (PS) phase (peak II), and the mutual diffusion between the PB blocks and PS blocks (peak III), respectively, were observed in the experimental range. Although ω was 0.1 rad/s, a noticeable peak III was gained for both l‐SBS and s‐SBS. The dynamic storage modulus (G′) of l‐SBS showed two distinct types of behavior, depending on the temperature. At temperature (T) < T₂ (where T₂ is the temperature corresponding to peak II), G′ of l‐SBS displayed a very weak ω dependency. In contrast, at T > T₂, G′ decayed much more rapidly. However, G′ of s‐SBS displayed a very weak ω dependency at both T < T₂ and T > T₂. Only near T₂ did s‐SBS decay with ω a little sharply. These indicated, in contrast to l‐SBS, that s‐SBS still exhibited more elasticity even at T > T₂ because of its crosslinking point between the PB blocks (the star structure). In the lower ω range, l‐SBS exhibited a stronger peak III than s‐SBS despite the same styrene content for l‐SBS and s‐SBS. The high tan δ value of peak III for l‐SBS was considered to be related to the internal friction among the PB blocks or the whole l‐SBS chain, not the PS blocks. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Novel method for preparation of quaternary ammonium ionomer from epoxidized styrene–butadiene–styrene triblock copolymer and its use as compatibilizer for blending of styrene–butadiene–styrene and chlorosulfonated polyethylene

A novel method for the preparation of a quaternary ammonium ionomer of styrene–butadiene–styrene triblock copolymer (SBS) was developed by a ring‐opening reaction of epoxidized SBS with triethylamine hydrochloride in the presence of a phase transfer catalyst. The optimum conditions were studied. The ionomer was characterized by quantitative analysis, IR spectroscopy, and ¹H‐NMR spectroscopy. Its water absorbency, oil absorbency, dilute solution viscosity, and use as a compatibilizer for the blending of SBS and chlorosulfonated polyethylene (CSPE) were investigated. The results showed that, under optimum conditions, the epoxy groups can be completely converted to the quaternary ammonium groups. The IR spectrum did not exhibit the absorption peak for quaternary ammonium groups, whereas the ¹H‐NMR spectrum and titration method demonstrated it. With increasing ionic group content, the water absorbency of the ionomer increased whereas its oil absorbency decreased. These indicated the amphiphilic character of the SBS ionomer. The dilute solution viscosity of the ionomer in toluene/methanol (9/1) solvent increased with increasing quaternary ammonium group content. The ionomer was used as a compatibilizer for the blends of SBS and CSPE. The addition of a small amount of the ionomer to the blend enhanced the mechanical properties of the blends: 2 wt % ionomer based on the blend increased the tensile strength and ultimate elongation of the blend nearly 2 times. The blends of equal parts SBS and CSPE behaved as oil‐resistant thermoplastic elastomers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1975–1980, 2006     

Toughening of polyamide 6 with a maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer

Maleic anhydride functionalized acrylonitrile–butadiene–styrene (ABS‐g‐MA) copolymers were prepared via an emulsion polymerization process. The ABS‐g‐MA copolymers were used to toughen polyamide 6 (PA‐6). Fourier transform infrared results show that the maleic anhydride (MA) grafted onto the polybutadiene phase of acrylonitrile–butadiene–styrene (ABS). Rheological testing identified chemical reactions between PA‐6 and ABS‐g‐MA. Transmission electron microscopy and scanning electron microscopy displayed the compatibilization reactions between MA of ABS‐g‐MA and the amine and/or amide groups of PA‐6 chain ends, which improved the disperse morphology of the ABS‐g‐MA copolymers in the PA‐6 matrix. The blends compatibilized with ABS‐g‐MA exhibited notched impact strengths of more than 900 J/m. A 1 wt % concentration of MA in ABS‐g‐MA appeared sufficient to improve the impact properties and decreased the brittle–ductile transition temperature from 50 to 10°C. Scanning electron microscopy results show that the shear yielding of the PA‐6 matrix was the major toughening mechanism. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Radiation-induced graft polymerization of 4-vinyl pyridine to styrene–butadiene–styrene triblock copolymer

The radiation-induced graft polymerization of 4-vinyl pyridine to styrene–butadiene–styrene triblock copolymer (SBS) was investigated. Relations between the rate of grafting and the dose rate when SBS was irradiated in 4-vinyl pyridine–methanol solution, and between the rate of grafting and 4-vinyl pyridine concentration of 4-vinyl pyridine–methanol solution have been investigated. An experiment that had been carried out on SBS immersed in various 4-vinyl pyridine concentration of 4-vinyl pyridine–methanol solutions showed that the extent of swelling of SBS by the various 4-vinyl pyridine–methanol solutions increased with increasing 4-vinyl pyridine concentration. The largest rate was found at 20 vol % 4-vinyl pyridine–methanol solution. The rate was smaller at the volume percent of 4-vinyl pyridine higher or lower than 20 vol %. On the assumption that the theory of homogeneous homopolymerization could be applied to this grafting reaction, the value of k_p²/k_t was obtained, where k_p and k_t are the propagation and termination constant, respectively. The value of k_p²/k_t greatly decreased with increasing adsorbed concentration of vinyl pyridine–methanol solution. This decrease of k_p²/k_t was explained by the fact that 4-vinyl pyridine and methanol absorbed in SBS acted as a plasticizer which increased the molecular motion of the polymer. The solvent effect on the graft polymerization was also investigated. The result was explained by solubility parameter. When the chosen solvent had better solubility with the polymer, the degree of grafting was smaller. That was connected with the extent of the polymer chain mobility.     

Physical and rheological properties of crumb rubber/styrene–butadiene–styrene compound modified asphalts

In order to improve the storage stability and tenacity of crumb rubber modified (CRM) asphalt, CRM compound modified asphalt was prepared by the addition of styrene–butadiene–styrene (SBS) and sulfur. The addition of SBS improved the tenacity of CRM asphalt, due to the formation of a dense polymer network. The storage stability of crumb rubber (CR)/SBS‐modified (CRSM) asphalt was improved by the addition of sulfur. The rheological tests confirmed the effect of SBS and sulfur on the physical properties of CRM asphalt to some extent and showed the susceptibility of CR/SBS/sulfur‐modified (CRSSM) asphalt to dynamic shearing. The morphology observation showed the compatibility of CRSM asphalt was improved greatly by vulcanization. POLYM. COMPOS., 38:1918–1927, 2017. © 2015 Society of Plastics Engineers     

Plasticization of nano‐CaCO3 in polystyrene/nano‐CaCO3 composites

The shear rheological properties of polystyrene (PS)/nano‐CaCO₃ composites were studied to determine the plasticization of nano‐CaCO₃ to PS. The composites were prepared by melt extrusion. A poly(styrene–butadiene–styrene) triblock copolymer (SBS), a poly(styrene–isoprene–styrene) triblock copolymer (SIS), SBS‐grafted maleic anhydride (SBS–MAH), and SIS‐grafted maleic anhydride were used as modifiers or compatibilizers. Because of the weak interaction between CaCO₃ and the PS matrix, the composites with 1 and 3 phr CaCO₃ loadings exhibited apparently higher melt shear rates under the same shear stress with respect to the matrix polymer. The storage moduli for the composites increased with low CaCO₃ concentrations. The results showed that CaCO₃ had some effects on the compatibility of PS/SBS (or SBS–MAH)/CaCO₃ composites, in which SBS could effectively retard the movement of PS chain segments. The improvement of compatibility, due to the chemical interaction between CaCO₃ and the grafted maleic anhydride, had obvious effects on the rheological behavior of the composites, the melt shear rate of the composites decreased greatly, and the results showed that nano‐CaCO₃ could plasticize the PS matrix to some extent. Rheological methods provided an indirect but useful characterization of the composite structure. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Photochromic behavior of naphthopyran in styrene–butadiene–styrene elastomer thin films: Effect of stretching of film and linker

Thermoplastic elastomers of styrene–butadiene–styrene (SBS) triblock copolymers containing grafts of naphthopyran as side‐chain polymer were prepared by polymerization of naphthopyran acrylate monomer with a solution of SBS in tetrahydrofuran. Thin films of all grafted SBS polymers displayed photochromism, the decoloration kinetics of naphthopyran in the films was modeled by fitting biexponential equations to the photochromic decay curves after UV light irradiation. Stretching of the grafted SBS film at room temperature affected the fading rate constant k₁ of the naphthopyran. The length of linker between photochromic naphthopyran moiety and the acrylate unit in monomer also affected the fading rate constant k₁ of the naphthopyran in SBS elastomers. This study presents an example of tuning the photochromic properties of naphthopyran via two approaches, polymer structure, and stretching of films. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013