Thermal stability and mechanical properties of nanocrystalline Fe–Ni–Zr alloys prepared by mechanical alloying

The thermal stability of nanostructured Fe_100?x?y Ni _x Zr _y alloys with Zr additions up to 4 at.% was investigated. This expands upon our previous results for Fe–Ni base alloys that were limited to 1 at.% Zr addition. Emphasis was placed on understanding the effects of composition and microstructural evolution on grain growth and mechanical properties after annealing at temperatures near and above the bcc-to-fcc transformation. Results reveal that microstructural stability can be lost due to the bcc-to-fcc transformation (occurring at 700 °C) by the sudden appearance of abnormally grown fcc grains. However, it was determined that grain growth can be suppressed kinetically at higher temperatures for high Zr content alloys due to the precipitation of intermetallic compounds. Eventually, at higher temperatures and regardless of composition, the retention of nanocrystallinity was lost, leaving behind fine micron grains filled with nanoscale intermetallic precipitates. Despite the increase in grain size, the in situ formed precipitates were found to induce an Orowan hardening effect rivaling that predicted by Hall–Petch hardening for the smallest grain sizes. The transition from grain size strengthening to precipitation strengthening is reported for these alloys. The large grain size and high precipitation hardening result in a material that exhibits high strength and significant plastic straining capacity.     

Solidification microstructures selection of Fe–Cr–Ni and Fe–Ni alloys

The transition of solidified phases in Fe–Cr–Ni and Fe–Ni alloys was investigated from low to high growth rate ranges using a Bridgman type furnace, laser resolidification and casting into a substrate from superheated or undercooled melt. The ferrite–austenite regular eutectic growth, which is difficult to find in typical production conditions of stainless steels, was confirmed under low growth rate conditions. The transition velocity between eutectic and ferrite cell growth had a good agreement predicted by the phase selection criterion. Which of either ferrite or austenite is easier to form in the high growth range was discussed from the point of nucleation and growth. Metastable austenite formation in stable primary ferrite composition was mainly a result of growth competition between ferrite and austenite. For a binary Fe–Ni system, a planar metastable austenite in the steady state, simultaneous growth such as eutectic and banded growth between ferrite and austenite in an initial transient region are confirmed.     

Tensile properties of the Cr–Fe–Ni–Mn non-equiatomic multicomponent alloys with different Cr contents

A series of Fe₄₀Mn₂₈Ni_32 − xCr_x (x = 4, 12, 18, 24 (at.%)) multicomponent alloys was prepared by vacuum arc melting. The Fe₄₀Mn₂₈Ni₂₈Cr₄, Fe₄₀Mn₂₈Ni₂₀Cr₁₂ and Fe₄₀Mn₂₈Ni₁₄Cr₁₈ alloys were ductile single phase fcc solid solutions. The Fe₄₀Mn₂₈Ni₈Cr₂₄ alloy had intermetallic sigma phase matrix and was extremely brittle after homogenization. The tensile properties of the Fe₄₀Mn₂₈Ni₂₈Cr₄, Fe₄₀Mn₂₈Ni₂₀Cr₁₂ and Fe₄₀Mn₂₈Ni₁₄Cr₁₈ solid solution alloys were examined in recrystallized condition with average grain size of ~ 10 μm. The yield strength increased from 210 MPa of the Fe₄₀Mn₂₈Ni₂₈Cr₄ alloy to 310 MPa of the Fe₄₀Mn₂₈Ni₁₄Cr₁₈ alloy. The elongation to fracture of the alloys decreased from 71% to 54%, respectively. Solid solution strengthening by the constitutive elements of the alloys was calculated using Labush approach. Strong solid solution strengthening by Cr was predicted. Gypen and Deruyttere approach was used to estimate solid solution strengthening of the Fe₄₀Mn₂₈Ni_32 − xCr_x alloys. Good correlation between predicted solid solution strengthening and the experimental yield strength values was found.     

The effects of cell spacing and distribution of intermetallic fibers on the mechanical properties of hypoeutectic Al–Fe alloys

The aim of the present investigation was to contribute to provide a basis for understanding how to control solidification parameters, microstructure and mechanical strength of Al–Fe alloys. Upward directional solidification experiments have been carried-out with commercially pure Al and Al–0.5 wt.% Fe, Al–1.0 wt.% Fe and Al–1.5 wt.% Fe alloys. The tensile tests results have been correlated to cell spacing (λ₁), since cellular growth has prevailed along all obtained Al–Fe castings. The used casting assembly was designed in such way that the heat was extracted only through the water-cooled system at the bottom of the casting. In order to investigate the nature of Al–Fe intermetallic fibers, they were extracted from the aluminum-rich matrix by using a dissolution technique. These fibers were then investigated by SEM-EDAX microscopy. It was found that the ultimate tensile strength, yield tensile strength and elongation increase with decreasing cell spacing. The highest ultimate tensile strength was that obtained for the most refined microstructure, i.e. for the Al–1.5 wt.% Fe alloy sample, where a higher density of eutectic fibers was found distributed in a more homogeneous way along the casting section due to lower cell spacings. In contrast, the elongation was found to decrease with increasing solute content.     

Microstructure,mechanical and corrosion properties and biocompatibility of Mg–Zn–Mn alloys for biomedical application

Mn and Zn were selected to develop a Mg–Zn–Mn magnesium alloy for biomedical application due to the good biocompatibility of Zn and Mn elements. Microstructure, mechanical properties, corrosion properties and biocompatibility of the Mg–Zn–Mn alloys have been investigated by use of optical microscope, scanning electron microscope, tensile testing, and blood hemolysis and cell toxicity. Microstructure observation has shown that the addition of Zn and the extrusion significantly refined the grain size of both the as-cast and the extruded magnesium alloys, which mainly contributes to the high tensile strength and good elongation. Polarization test has shown Zn could accelerate the formation of a passivation film, which provides good protection to the magnesium alloy against simulate body fluid. Cell culture and hemolysis tests have shown that the magnesium alloy did not have cell toxicity, showing good cytocompatibility, but the alloy caused hemolysis to blood system. It was suggested that surface modification have to be adopted to improve the blood compatibility of the magnesium alloy for the application in blood environment.     

Investigation of corrosion and mechanical properties of Al–Cu–SiC–xNi composite alloys

In this study, dry sliding wear behavior and corrosion resistance of Al–Cu–SiC–xNi (x: 0, 0.5, 1, 1.5 wt.%) composites were investigated. Effect of nickel content on the microstructure and hardness of the alloys was also studied. Wear tests were conducted using a ball on disc wear test device. Corrosion behavior of Al–Cu–SiC–xNi composite alloys in 3.5% NaCl solution was investigated by using potentiodynamic polarization, impedance spectroscopy and cronoamperometric methods. The results showed that the hardness of the composite alloy increases with increasing nickel content. Maximum wear resistance is reported with the addition of 1 wt.%Ni. It was determined that corrosion resistance of Al–Cu–SiC composite alloys improved with increasing nickel content in the alloy.     

Density and thermal expansion of Cr–Fe, Fe–Ni, and Cr–Ni binary liquid alloys

Densities and their temperature coefficients of liquid Cr–Fe, Fe–Ni, and Cr–Ni binary alloys have been measured containerless using the technique of electromagnetic levitation. Data have been obtained in a wide temperature range including the supercooled region. The density measurements indicate that these binary systems have a small and positive excess volume, whereas the excess free energies are negative. The temperature coefficients of these alloys can be estimated from those of the pure components. Hence, possible contributions from the temperature dependence of the excess volume can be ignored to calculate the temperature coefficient of density.     

Density and viscosity of ternary Cr–Fe–Ni liquid alloys

The density and viscosity of ternary Cr–Fe–Ni liquid alloys have been investigated over a wide temperature range. The density was measured using electromagnetic levitation as a container-less technique, while viscosity was measured by means of a high-temperature oscillating cup viscometer. Although, the concentration dependence of density shows the influence of the second order (binary) interaction parameter in excess volume, the influence of a third order (ternary) interaction parameter in excess volume can be neglected. The temperature dependences of the viscosities are well described by the Arrhenius law. The viscosity increases monotonically as Fe or Cr concentration increases. For constant temperature, the viscosity as a function of iron molar faction can be described by a thermodynamic model using the enthalpy of mixing as input parameter.     

Microstructural characterisation and mechanical properties of Ni–Ge alloys containing Ni3Ge

Abstract

Six Ni–Ge alloys were prepared and equilibrated at 1000°C. The microstructures, compositions of phases, solubilities in various phases, volume fractions of phases, lattice parameters of Ni₃ Ge, and microhardness values of phases were determined. Two alloys contained Ni₃Ge and α, one alloy was single phase Ni₃Ge, and three alloys contained Ni₃Ge and Ni₅Ge₃. The volume fractions of second phase were 6 and 33%α and 37 and 54%Ni₅Ge₃. The amount of second phase in the third Ni₃Ge–Ni₅Ge₃ alloy was too low to be determined accurately. The two phase alloys containing 6%α, 37%Ni₅Ge₃, or 54%Ni₅Ge₃ were tested in compression. A yield strength maximum was observed in the three alloys. The deformation behaviour of the alloy containing 6%α was similar to that of single phase Ni₃Ge: crack formation along Ni₃Ge grain boundaries and very low plastic strain were revealed. In alloys containing Ni₃Ge and an appreciable percentage of Ni₅Ge₃, crack formation was not observed along Ni₃Ge grain boundaries. Instead, at low temperatures, deformation and crack growth occurred within Ni₅Ge₃ grains and, at high temperatures, decohesion occurred along the Ni₃Ge/Ni₅Ge₃ interphase. The plastic strain in the alloy containing 54%Ni₅Ge₃ increased to about 40%.

MST/1724     

Microstructure development and mechanical properties of rapidly solidified Ti–Fe and Ti–Fe–Bi alloys

Even though rapidly solidified Ti–Fe eutectic alloys may achieve good mechanical strength, increase in ductility is already a task to be accomplished. Addition of tin and arrangements of nano- and ultrafine-grain metallic materials have been shown as potential alternatives to overcome such drawback. Also, to address this problem, it seems that alternative alloy chemistries and processing routes must be adopted when manufacturing Ti-based alloys. In the present investigation, Ti–26 wt.%Fe (Ti–24.5 at.%Fe) and Ti–20 wt.%Fe–3 wt.%Bi (Ti–18 at.%Fe–0.7 at.%Bi) alloys have been prepared in a stepped copper mold using centrifugal casting. The as-cast Ti–Fe(–Bi) microstructures were formed by equiaxial arrangements of cells. Finer cell spacing (λ_c) was associated with the Ti–20 wt.%Fe–3 wt.%Bi alloy. The results include cell spacing measurements, segregation profile by X-ray fluorescence (XRF), uniaxial compression tests, optical microscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). A wide variation on the scale of the microstructure was noted especially in the case of the Ti–26 wt.%Fe alloy with the λ_c varying from 11−30 μm. This is due to the different cooling conditions of each diameter along the as-cast rod. Hall–Petch type equations are proposed relating σ_max to λ_c. Bi was dissolved in the β-Ti solid solution as well as TiFe compound formed in the cellular structure of the Ti–20 wt.%Fe–3 wt.%Bi.     

Effect of strain rate on microstructures and mechanical properties of Fe–18Cr–8Ni steel

The effect of strain rate on deformation microstructures and mechanical properties of Fe–18Cr–8Ni austenitic stainless steel was investigated at strain rates of from 10^?3 to 100?s^?1. The results indicated that the deformation mechanism of steel changes from transformation induced plasticity (TRIP) to TRIP?+?twinning induced plasticity (TWIP) effect when the strain rate is increased from 10^?3 to 100?s^?1. The yield strength of steel increases gradually with strain rate increased, while the tensile strength and elongation first decreases and then increases slowly. The changes in tensile strength and elongation are due to the change of deformation mechanism with the strain rate increased.     

Effect of silicon content on the microstructure and properties of Fe–Cr–C hardfacing alloys

In this study, the surface of St52 steel was alloyed with preplaced powders 55Fe39Cr6C, 49Fe39Cr6C6Si, and 45Fe39Cr6C10Si using a tungsten-inert gas as the heat source. Following surface alloying, conventional characterization techniques, such as optical microscopy, scanning electron microscopy, and X-ray diffraction were employed to study the microstructure of the alloyed surface. Microhardness measurements were performed across the alloyed zone. Room-temperature dry sliding wear tests were used to compare the coatings in terms of their tribological behavior. It was found that the as-deposited coatings contained higher volume fractions of carbides (Cr₇C₃). The presence of 6%Si in the preplaced powders caused an increase in microhardness and wear resistance.     

Influence of solution treatment temperature on mechanical properties of a Fe–Ni–Cr alloy

Influence of solution treatment temperature on mechanical properties of a Fe–Ni–Cr alloy was studied in this work. The results indicate that the strength and the ductile properties are optimum after solution treatment at 1000 °C followed by conventional two-step aging, but decrease markedly with the increase of solution temperature. Microstructure analyses show that TiC phase particles in the microstructure partly dissolves into the matrix when the solution treatment temperature is higher than 1100 °C, resulting in the coarsening of austenitic grain. Flake-like M₃B₂ phase precipitates at the grain boundary in the specimens solution-treated at temperatures higher than 1050 °C and its formation induces the mechanical properties to be worse.     

Influence of atomized powder size on microstructures and mechanical properties of rapidly solidified Al–Cr–Y–Zr aluminum alloys

Rapidly solidified powders of Al–5.0Cr–4.0Y–1.5Zr (wt%) were prepared by using a multi-stage atomization-rapid solidification powder-making device. The atomized powders were sieved into four shares with various nominal diameter level and were fabricated into hot-extruded bars after cold-isostatically pressing and vaccum degassing process. Influence of atomized powder size on microstructures and mechanical properties of the hot-extruded bars was investigated by optical microscopy, X-ray diffraction, transmission electronic microscopy with EPSX and scanning electron microscopy. The results show that the fine atomized powders of rapidly solidified Al–5.0Cr–4.0Y–1.5Zr aluminum alloy attains supersaturated solid solution state under the exist condition of multi-stage rapid solidification. With the powder size increasing, there are Al₂₀Cr₂Y (cubic, a = 1.437 nm) and Ll₂ Al₃Zr (FCC, a = 0.407 nm) phase forming in the powders, and even lumpish particles of Al₂₀Cr₂Y appearing in the coarse atomized powders, as can be found in the as-cast master alloy. Typical microstructures of the extruded bars of rapidly solidified Al–5.0Cr–4.0Y–1.5Zr aluminum alloy can be characterized by fine grain FCC α-Al matrix with ultra-fine spherical particles of Al₂₀Cr₂Y and Al₃Zr. But a small quantity of Al₂₀Cr₂Y coarse lumpish particles with micro-twin structures can be found, originating from lumpish particles of the coarse powders. The extruded bars of rapidly solidified Al–5.0Cr–4.0Y–1.5Zr aluminum alloy by using the fine powders eliminated out too coarse powders have good tensile properties of σ_0.2 = 403 MPa, σ_b = 442 MPa and δ = 9.4% at room temperature, and σ_0.2 = 153 MPa, σ_b = 164 MPa and δ = 8.1% at high temperature of 350 °C.     

Effect of Al and C on structure and mechanical properties of Fe–Al–C alloys

Abstract

Effect of aluminium and carbon content on the microstructure and mechanical properties of Fe–Al–C alloys has been investigated. Alloys were prepared by combination of air induction melting with flux cover (AIMFC) and electroslag remelting (ESR). The ESR ingots were hot forged and hot rolled at 1373 K. As rolled alloys were examined using optical microscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to understand the microstructure of these alloys. The ternary Fe–Al–C alloys containing 10·5 and 13 wt-%Al showed the presence of three phases: FeAl with disordered bcc structure, Fe₃Al with ordered DO₃ structure and Fe₃AlC_0·5 precipitates with L′1₂ structure. Addition of high concentration of carbon to these alloys resulted in excellent hot workability and superior tensile at room temperature as well as tensile and creep properties at 873 K. An increase in Al content from 9 to 13 wt-% in Fe–Al–C alloys containing the same levels of carbon has no significant influence on strength and creep properties at 873 K, however resulted in significant improvement in room temperature strength accompanied by a reduction in room temperature ductility.     

Effects of Ca on microstructure, mechanical and corrosion properties and biocompatibility of Mg–Zn–Ca alloys

Zn and Ca were selected as alloying elements to develop an Mg–Zn–Ca alloy system for biomedical application due to their good biocompatibility. The effects of Ca on the microstructure, mechanical and corrosion properties as well as the biocompatibility of the as-cast Mg–Zn–Ca alloys were studied. Results indicate that the microstructure of Mg–Zn–Ca alloys typically consists of primary α-Mg matrix and Ca₂Mg₆Zn₃/Mg₂Ca intermetallic phase mainly distributed along grain boundary. The yield strength of Mg–Zn–Ca alloy increased slightly with the increase of Ca content, whilst its tensile strength increased at first and then decreased. Corrosion tests in the simulated body fluid revealed that the addition of Ca is detrimental to corrosion resistance due to the micro-galvanic corrosion acceleration. In vitro hemolysis and cytotoxicity assessment disclose that Mg–5Zn–1.0Ca alloy has suitable biocompatibility.     

Cryorolling effect on microstructure and mechanical properties of Fe–25Cr–20Ni austenitic stainless steel

Microstructure and mechanical properties of the Fe–25Cr–20Ni austenitic stainless steel after cryorolling with different reductions were investigated by means of optical, scanning and transmission electron microscopy, X-ray diffraction and mini-tensile testing. High density tangled dislocations and a small amount of deformation twins formed after 30% deformation. After 50% strain, a large amount of deformation twins was generated. Meanwhile, interactions between the twins and dislocations started to happen. As the strain increased to 70%, many deformation twins were produced and the interactions between the twins and dislocations were significantly enhanced. When the cryorolling was 90%, the grain size was refined to the nanometer scale. XRD analysis indicated that the diffraction peaks of the samples became broader with the strain increase. The yield strength and the ultimate strength increased from 305 MPa and 645 MPa (before deformation) to 1502 MPa and 1560 MPa (after 90% deformation), respectively. However, the corresponding elongation decreased from 40.8% to 6.4%. The tensile fracture morphology changed from typical dimple rupture to a mixture of quasi-cleavage and ductile fracture. After 90% deformation, the microhardness was 520 HV, which increased by 100% compared with the original un-deformed sample.     

Effects of Zn on microstructure,mechanical properties and corrosion behavior of Mg–Zn alloys

In this study, binary Mg–Zn alloys were fabricated with high-purity raw materials and by a clean melting process. The effects of Zn on the microstructure, mechanical property and corrosion behavior of the as-cast Mg–Zn alloys were studied using direct observations, tensile testing, immersion tests and electrochemical evaluations. Results indicate that the microstructure of Mg–Zn alloys typically consists of primary α-Mg matrix and MgZn intermetallic phase mainly distributed along grain boundary. The improvement in mechanical performances for Mg–Zn alloys with Zn content until 5% of weight is corresponding to fine grain strengthening, solid solution strengthening and second phase strengthening. Polarization test has shown the beneficial effect of Zn element on the formation of a protective film on the surface of alloys. Mg–5Zn alloy exhibits the best anti-corrosion property. However, further increase of Zn content until 7% of weight deteriorates the corrosion rate which is driven by galvanic couple effect.     

Effect of Al addition on the grain refinement and mechanical properties of as-cast Mg–5Y–4Sm alloys

Journal of Materials Science - In recent years, the utilization of Al as a grain refiner in Mg–RE alloys has gained widespread attention because of its advantages such as low cost. In this...     

Microstructures, mechanical properties and in vitro corrosion behaviour of biodegradable Mg–Zr–Ca alloys

The microstructures, mechanical properties, corrosion behaviour and biocompatibility of the Mg–Zr–Ca alloys have been investigated for potential use in orthopaedic applications. The microstructures of the alloys were examined using X-ray diffraction analysis, optical microscopy and scanning electron microscopy. The mechanical properties of Mg–Zr–Ca alloys were determined from compressive tests. The corrosion behaviour has been investigated using an immersion test and electrochemical measurement. The biocompatibility was evaluated by cell growth factor using osteoblast-like SaOS2 cell. The experimental results indicate that the hot-rolled Mg–Zr–Ca alloys exhibit much finer microstructures than the as-cast Mg–Zr–Ca alloys which show coarse microstructures. The compressive strength of the hot-rolled alloys is much higher than that of the as-cast alloys and the human bone, which would offer appropriate mechanical properties for orthopaedic applications. The corrosion resistance of the alloys can be enhanced significantly by hot-rolling process. Hot-rolled Mg–0.5Zr–1Ca alloy (wt %) exhibits the lowest corrosion rate among all alloys studied in this paper. The hot-rolled Mg–0.5Zr–1Ca and Mg–1Zr–1Ca alloys exhibit better biocompatibility than other studied alloys and possess advanced mechanical properties, corrosion resistance and biocompatibility, suggesting that they have a great potential to be good candidates for orthopaedic applications.