硅烷偶联剂对纳米二氧化钛表面改性的研究

利用硅烷偶联剂（KH-570）对表面包覆氧化硅的金红石相纳米TiO2进行了有机表面改性．采用红外光谱（IR）、X射线光电子能谱（XPS）、热分析（TG-DTA）、透射电镜（TEM）和润湿性实验等分析手段对表面改性前后的纳米TiO2进行了表征．红外光谱和X射线光电子能谱表明，KH-570以化学键合的方式结合在纳米TiO2的表面，并形成了有机包覆层．经测量，纳米TiO2表面包覆的KH-570的质量分数约为7．42％-8．59％．润湿性实验显示，经KH-570表面改性的纳米TiO2具有疏水性．力学性能实验表明，经KH-570表面改性的纳米TiO2能同时提高复合材料的强度和韧性．     

ZnO/Al_2O_3复合纳米颗粒的制备与表征

为研究ZnO/Al2O3复合纳米颗粒在涂料、化妆品等领域的应用,采用直接沉淀法制备了纳米ZnO,用硫酸铝水解生成的Al2O3对纳米ZnO进行了表面改性。采用IR、TEM、SEM、XRD等手段对改性前后的粉体进行表征。分析结果表明,改性后粉体颗粒的团聚现象减轻。粉体的光催化降解甲基橙的实验研究表明,改性后ZnO粉体的光催化活性明显下降,进一步证明纳米ZnO颗粒表面存在Al2O3的包覆层。     

纳米AlN/EP导热绝缘胶的制备及其性能研究

采用纳米AIN作为导热填料,经硅烷偶联剂KH-570表面改性后与环氧树脂(EP)共混制备了导热绝缘胶.通过红外光谱(FT-IR)、接触角方法对改性后纳米AIN进行分析和表征,结果表明,KH-570成功包覆到了纳米AIN表面,粉体由亲水性变为疏水性;对于纳米AIN/EP导热绝缘胶,随着改性纳米AIN填充量的增加,导热率呈上升趋势;当KH-570用量为3.5%、纳米AIN量为20%时,导热率达到0.632W/(m·K),是纯环氧树脂胶的3倍多;此时体积电阻率为2.6×1013Ω·cm,剪切冲击强度为11.9×1015J/m2.     

纳米ATO在有机单体介质中的表面改性及分散研究

选用了多种改性剂,用超声波为分散手段,将纳米ATO粉体在有机单体介质中进行表面改性和分散,研究了改性剂种类、改性剂用量、改性时间、超声波输出功率和超声波处理时间等对纳米ATO-单体分散液稳定性的影响,探讨了纳米ATO表面改性机理.结果表明,硅烷偶联剂KH-570是纳米ATO的最佳改性剂,当其用量为纳米ATO的15%(质量分数),改性时间为24h,超声波输出功率为90%,超声波处理时间为12min时,纳米ATO-单体分散液具有最佳的分散稳定性.KH-570主要通过在纳米ATO表面水解产生硅羟基的自缩合,形成包覆改性.     

ZnO/Al2O3复合纳米颗粒的制备与表征

以硫酸锌和氢氧化钠为原料,采用直接沉淀法制备了纳米氧化锌,并用硫酸铝水解生成的三氧化铝对钠米氧化锌进行了表面改性,并采用IR、TEM、SEM、XRD等手段对改性前后的粉体进行表征研究.TEM和SEM分析结果表明,改性后粉体颗粒的粒径小、团聚现象减轻.此外,进行了粉体的光催化降解甲基橙的实验研究.实验结果表明,改性后ZnO粉体的光催化活性明显下降,这进一步证明了纳米氧化锌颗粒表面存在三氧化二铝的包覆层.     

ZnO/Al2O3复合纳米颗粒的制备与表征

以硫酸锌和氢氧化钠为原料,采用直接沉淀法制备了纳米氧化锌,并用硫酸铝水解生成的三氧化铝对钠米氧化锌进行了表面改性,并采用IR、TEM、SEM、XRD等手段对改性前后的粉体进行表征研究.TEM和SEM分析结果表明,改性后粉体颗粒的粒径小、团聚现象减轻.此外,进行了粉体的光催化降解甲基橙的实验研究.实验结果表明,改性后ZnO粉体的光催化活性明显下降,这进一步证明了纳米氧化锌颗粒表面存在三氧化二铝的包覆层.     

硅烷偶联剂对纳米ZnO的有机表面修饰研究

利用硅烷偶联荆(LM-N308)对纳米ZnO进行了有机表面改性.采用红外光谱(IR)、热分析(TG-DTA)、高分辨透射电镜(HRTEM)、润湿性实验等对表面改性前后的纳米ZnO进行了表征.红外光谱和高分辨透射电镜结果表明,在纳米ZnO表面有LM-N308的存在,并形成了有机包覆层.润湿性实验表明,经LM-N308表面改性的纳米ZnO由亲水性变成了疏水性.     

硅烷偶联剂KH-570表面改性纳米SiO2

采用硅烷偶联剂KH-570在酸性条件下对纳米SiO2表面进行改性,并对改性前后的纳米SiO2采用粒径分析仪、傅里叶红外变换光谱仪、紫外-可见光光谱仪、扫描电镜等仪器进行了分析和表征。结果表明,硅烷偶联剂KH-570能成功地对纳米SiO2表面进行改性,使其表面化学键合了硅烷偶联剂的有机官能团,降低了颗粒团聚程度,提高了纳米SiO2在有机介质中的分散程度     

纳米TiO_2的改性及其性能研究

采用KH-570、正辛醇和辛酰氯分别对纳米TiO2进行改性,利用傅立叶红外光谱、差热/热重分析及X-射线衍射仪对改性前后纳米TiO2进行表征,结果表明纳米TiO2的改性为化学改性,改性剂与纳米TiO2表面羟基形成稳定的化学键,但并没有改变纳米TiO2的晶型结构。改性后的纳米TiO2在有机溶剂中的分散性和稳定性提高,尤其是KH-570改性纳米TiO2的效果最好,具有更强的疏水性。KH-570改性纳米TiO2与丙烯酸树脂复合后,能在树脂中均匀分散,不易团聚。     

硅烷偶联剂KH-570对纳米二氧化硅的表面改性研究

为改善用作农药载体的纳米SiO2的分散性和疏水性,以硅烷偶联剂KH-570对纳米SiO2进行了表面改性,通过SEM、XRD、FTIR以及元素分析等表征方法对产物结构和性能进行了分析,结果表明,KH-570能够成功地对纳米SiO2进行改性,并且提高其分散性。最佳偶联改性的反应条件为：改性剂用量5%,改性时间5h。在此条件下,改性纳米SiO2的接枝率为11.7%。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...