Mechanistic aspects of N2O and N2 formation in NO reduction by NH3 over Ag/Al2O3: The effect of O2 and H2

A mechanistic scheme of N₂O and N₂ formation in the selective catalytic reduction of NO with NH₃ over a Ag/Al₂O₃ catalyst in the presence and absence of H₂ and O₂ was developed by applying a combination of different techniques: transient experiments with isotopic tracers in the temporal analysis of products reactor, HRTEM, in situ UV/vis and in situ FTIR spectroscopy. Based on the results of transient isotopic analysis and in situ IR experiments, it is suggested that N₂ and N₂O are formed via direct or oxygen-induced decomposition of surface NH₂NO species. These intermediates originate from NO and surface NH₂ fragments. The latter NH₂ species are formed upon stripping of hydrogen from ammonia by adsorbed oxygen species, which are produced over reduced silver species from NO, N₂O and O₂. The latter is the dominant supplier of active oxygen species. Lattice oxygen in oxidized AgO_x particles is less active than adsorbed oxygen species particularly below 623 K. The previously reported significant diminishing of N₂O production in the presence of H₂ is ascribed to hydrogen-induced generation of metallic silver sites, which are responsible for N₂O decomposition.     

Global kinetic modelling of the reaction of soot with O2 and NOx on Fe2O3 catalyst

This study deals with the catalytic reaction of NO_x and soot on Fe₂O₃ to yield N₂ and CO₂ in excess of oxygen. Based on the three types of kinetic experiments, i.e. temperature programmed oxidation (TPO), transient examinations and gradient-free loop reactor experiments, as well as mechanistic studies presented recently a global kinetic model is established. The model includes catalytic effect of the iron oxide on soot/O₂ reaction, whereas it is assumed that NO_x reduction occurs on the soot without direct participation of Fe₂O₃. Furthermore, the model implies global kinetic expressions for the CO_x formation and NO_x reduction. These equations include the evolution of the surface area of soot and the correlation of reactive carbon sites (C_f) with those specifically involved in NO_x reduction (C*). The kinetic model is sequentially developed by accounting for the catalytic and non-catalytic soot/O₂ as well as soot/NO_x/O₂ conversion. Kinetic parameters are taken from the literature and are also determined from a fit to experimental data. Comparison of measured and calculated data shows accurate reproduction of the experiments and the model. Finally, the kinetic model is validated by some simulations.     

Kinetic modeling of storage and reduction with different reducing agents (CO, H2, and C2 H4) on a Pt–Ba/-Al2O3 catalyst in the presence of CO2 and H2O

In this paper a global reaction kinetic model is used to understand and describe the NO_x storage/reduction process in the presence of CO₂ and H₂O. Experiments have been performed in a packed bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings at different temperatures (200, 250, and ) and using different reductants (H₂, CO, and C₂H₄). Model simulations and experimental results are compared. H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. The rate of NO storage increases with temperature. The reduction of stored NO with H₂ is complete for all investigated temperatures. At temperatures above , the water gas shift (WGS) reaction takes place and H₂ acts as reductant instead of CO. At , CO and C₂H₄ are not able to completely regenerate the catalyst. At the higher temperatures, C₂H₄ is capable of reducing all the stored NO, although C₂H₄ poisons the Pt sites by carbon decomposition at . The model adequately describes the NO breakthrough profile during 100 min lean exposure as well as the subsequent release and reduction of the stored NO. Further, the model is capable of simulating transient reactor experiments with 240 s lean and 60 s rich cycle timings.     

Selective Catalytic Reduction of NOx over H-ZSM-5 Under Lean Conditions Using Transient NH3 Supply

The selective catalytic reduction (SCR) of NO _x over zeolite H-ZSM-5 with ammonia was investigated using in situ FTIR spectroscopy and flow reactor measurements. The adsorption of ammonia and the reaction between NO _x , O₂ and either pre-adsorbed ammonia or transiently supplied ammonia were investigated for either NO or equimolar amounts of NO and NO₂. With transient ammonia supply the total NO reduction increased and the selectivity to N₂O formation decreased compared to continuous supply. The FTIR experiments revealed that NO _x reacts with ammonia adsorbed on Brønsted acid sites as NH₄ ⁺ ions. These experiments further indicated that adsorbed -NO₂ ^– is formed during the SCR reaction over H-ZSM-5.     

Dynamics and selectivity of NOx reduction in NOx storage catalytic monolith

Several nitrogen compounds can be produced during the regeneration phase in periodically operated NO_x storage and reduction catalyst (NSRC) for conversion of automobile exhaust gases. Besides the main product N₂, also NO, N₂O, and NH₃ can be formed, depending on the regeneration phase length, temperature, and gas composition. This contribution focuses on experimental evaluation of the NO_x reduction dynamics and selectivity towards the main products (NO, N₂ and NH₃) within the short rich phase, and consequent development of the corresponding global reaction-kinetic model. An industrial NSRC monolith sample of PtRh/Ba/CeO₂/ -Al₂O₃ type is employed in nearly isothermal laboratory micro-reactor. The oxygen and NO_x storage/reduction experiments are performed in the temperature range 100–500 °C in the presence of CO₂ and H₂O, using H₂, CO and C₃H₆ as the reducing agents.The spatially distributed NSRC model developed earlier is extended by the following reactions: NH₃ is formed by the reaction of H₂ with NO_x and it can further react with oxygen and NO_x deposited on the catalyst surface, producing N₂. Considering this scheme with ammonia as an active intermediate of the NO_x reduction, a good agreement with experiments is obtained in terms of the NO_x reduction dynamics and selectivity. A reduction front travelling in the flow direction along the reactor is predicted, with the NH₃ maximum on the moving boundary. When the front reaches the reactor outlet, the NH₃ peak is observed in the exhaust gas. It is assumed that the ammonia formation during the NO_x reduction by CO and HCs at higher temperatures proceed via the water gas shift and steam reforming reactions producing hydrogen. It is further demonstrated that oxygen storage effects influence the dynamics of the stored NO_x reduction. The temperature dependences of the outlet ammonia peak delay and the selectivity towards NH₃ are correlated with the effective oxygen and NO_x storage capacity.     

Influence of low concentration of SO2 for selective reduction of NO by C3H8 in lean-exhaust conditions on the activity of Ag/Al2O3 catalyst

The effect of SO₂ for the selective reduction of NO by C₃H₈ on Ag/Al₂O₃ was investigated in the presence of excess oxygen and water vapor. The NO_x conversion decreased permanently even in the presence of a low concentration of SO₂ (0.5–10 ppm) at <773 K. The increase in SO₂ concentration resulted in a large decrease in NO_x conversion at 773 K. However, when the reaction temperature was more than 823 K, the activity of Ag/Al₂O₃ remained constant even in the presence of 10 ppm of SO₂. The sulfate species formed on the used Ag/Al₂O₃ were characterized by a temperature programmed desorption method. The sulfated species formed on silver should mainly decrease the deNO_x activity on the Ag/Al₂O₃. The sulfated Ag/Al₂O₃ was appreciably regenerated by thermal treatment in the deNO_x feed at 873 K. The moderate activity remains at 773 K in the presence of 1 ppm SO₂ for long time by the heat treatment at every 20 h intervals.     

A comparative study of the selective oxidation of NH3 to N2 over gold, silver and copper catalysts and the effect of addition of Li2O and CeOx

This paper describes the selective oxidation of ammonia into nitrogen over copper, silver and gold catalysts between room temperature and 400 °C using different NH₃/O₂ ratios. The effect of addition of CeO_x and Li₂O on the activity and selectivity is also discussed. The results show that copper and silver are very active and selective toward N₂. However the multicomponent catalysts: M/Li₂O/CeO_x/Al₂O₃ (M: Au, Ag, Cu) perform the best. On all three metal containing catalysts the activity and selectivity is influenced by the particle size and the interaction between metal particles and support.     

Influence of the Type of Reducing Agent (H2, CO, C3H6 and C3H8) on the Reduction of Stored NOX in a Pt/BaO/Al2O3 Model Catalyst

In this investigation, a comparative study for a NO _X storage catalytic system was performed focusing on the parameters that affect the reduction by using different reductants (H₂, CO, C₃H₆ and C₃H₈) and different temperatures (350, 250 and 150 °C), for a Pt/BaO/Al₂O₃ catalyst. Transient experiments show that H₂ and CO are highly efficient reductants compared to C₃H₆ which is somewhat less efficient. H₂ shows a significant reduction effect at relatively low temperature (150 °C) but with a low storage capacity. We find that C₃H₈does not show any NO _X reduction ability for NO _X stored in Pt/BaO/Al₂O₃ at any of the temperatures. The formation of ammonia and nitrous oxide is also discussed.     

NOx Reduction over CeO2–ZrO2 Supported Iridium Catalyst in the Presence of Propanol

The 1-propanol assisted-reduction of NO _x was investigated over Ir/Ce_0.6Zr_0.4O₂. The catalytic performances of such a catalyst, the associated FTIR characterizations, and transient experiments suggest the formation of adsorbed R-NO _x species as intermediates of the deNO _x process; they provide the partially oxidized species required by the deNO _x model.     

The effect of co-doping with MgO and Yb2O3 on the structure and electrical conductivity of the Sm2Zr2O7 pyrochlore

SmYb_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.15) ceramics are pressureless-sintered at 1973 K for 10 h in air. The structure and electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics are investigated by the X-ray diffraction, scanning electron microscopy and impedance spectroscopy measurements. SmYb_1−xMg_xZr₂O_7−x/2 ceramics exhibit a defect fluorite-type structure. The measured electrical conductivities of SmYb_1−xMg_xZr₂O_7−x/2 ceramics obey the Arrhenius relation, and electrical conductivity of each composition increases with increasing temperature from 673 to 1173 K. At identical temperature levels, the electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics gradually increases with increasing magnesia content. SmYb_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The electrical conductivity obtained in SmYb_1−xMg_xZr₂O_7−x/2 ceramics reaches the highest value of 2.72 × 10⁻³ S cm⁻¹ at 1173 K for the SmYb_0.85Mg_0.15Zr₂O_6.925 ceramic.     

Catalytic steam reforming of ethane and propane over CeO2-doped Ni/Al2O3 at SOFC temperature: Improvement of resistance toward carbon formation by the redox property of doping CeO2

Ni/Al₂O₃ with the doping of CeO₂ was found to have useful activity to reform ethane and propane with steam under Solid Oxide Fuel Cells (SOFCs) conditions, 700-900 °C. CeO₂-doped Ni/Al₂O₃ with 14% ceria doping content showed the best reforming activity among those with the ceria content between 0 and 20%. The amount of carbon formation decreased with increasing Ce content. However, Ni was easily oxidized when more than 16% of ceria was doped. Compared to conventional Ni/Al₂O₃, 14%CeO₂-doped Ni/Al₂O₃ provides significantly higher reforming reactivity and resistance toward carbon deposition. These enhancements are mainly due to the influence of the redox properties of doped ceria. Regarding the temperature programmed reduction experiments (TPR-1), the redox properties and the oxygen storage capacity (OSC) for the catalysts increased with increasing Ce doping content. In addition, it was also proven in the present work that the redox of these catalysts are reversible, according to the temperature programmed oxidation (TPO) and the second time temperature programmed reduction (TPR-2) results.During the reforming process, in addition to the reactions on Ni surface, the gas-solid reactions between the gaseous components presented in the system (C₂H₆, C₃H₈, C₂H₄, CH₄, CO₂, CO, H₂O, and H₂) and the lattice oxygen (O_x) on ceria surface also take place. The reactions of adsorbed surface hydrocarbons with the lattice oxygen (O_x) on ceria surface (C_nH_m+O_x→nCO+m/2(H₂)+O_x−n) can prevent the formation of carbon species on Ni surface from hydrocarbons decomposition reaction (C_nH_m⇔nC+m/2H₂). Moreover, the formation of carbon via Boudard reaction (2CO⇔CO₂+C) is also reduced by the gas-solid reaction of carbon monoxide (produced from steam reforming) with the lattice oxygen (CO+O_x⇔CO₂+O_x−1).     

Theoretical and experimental study on the emission characteristics of waste plastics incineration by modified O2/RFG combustion technology

For mitigating the emission of greenhouse gas CO₂ from general air combustion systems, a clean combustion technology O₂/RFG is in development. The O₂/RFG combustion technology can significantly enhance the CO₂ concentration in the flue gas; however, using almost pure oxygen or pure CO₂ as feed gas is uneconomic and impractical. As a result, this study proposes a modified O₂/RFG combustion technology in which the minimum pure oxygen is mixed with the recycled flue gas and air to serve as the feed gas. The effects of different feed gas compositions and ratios of recycled flue gas on the emission characteristics of CO₂, CO and NO_x during the plastics incineration are investigated by theoretical and experimental approaches.Theoretical calculations were carried out by a thermodynamic equilibrium program and the results indicated that the emissions of CO₂ were increased with the O₂ concentrations in the feed gas and the ratios of recycled flue gas increased. Experimental results did not have the same trends with theoretical calculations. The best feed gas composition of the modified O₂/RFG combustion was 40% O₂ + 60% N₂ and the best ratio of recycled flue gas was 15%. As the O₂ concentration in feed gas and the ratio of recycled flue gas increased, the total flow rates and pressures of feed gas reduced. The mixing of solid waste and feed gas was incomplete and the formation of CO₂ decreased. Moreover, the emission of CO was decreased as the O₂ concentration in feed gas and the ratio of recycled flue gas increased. The emission of NO_x gradually increased with rising the ratio of recycled flue gas at lower O₂ concentration (<40%) but decreased at higher O₂ concentration (>60%).     

FTIR study of NO, C3H6 and O2 adsorption and interaction on gold modified MCM-41 materials

This paper is devoted to the detailed FTIR study of the adsorption, co-adsorption, and interaction of all the reagents used in NO HC-SCR process addressed to lean-burn engines with the surface of new gold catalysts based on ordered mesoporous materials. Gold was introduced into silicate and niobiosilicate matrices by the impregnation (Au/MCM-41 and Au/NbMCM-41, respectively) and via co-precipitation with siliceous and niobium sources (AuNbMCM-41). The in situ FTIR study allowed the estimation of the possible chemisorption of the reagents and their interaction towards intermediates, depending on the chemical composition of the catalyst and the way of gold introduction. It has been found that propene is chemisorbed, but not, NO, on gold species at room temperature. Chemisorbed C₃H₆ interacts with NO only in the presence of oxygen excess. Oxygen oxidizes NO to NO₂, the latter interacts with chemisorbed propene towards carboxylates (1570 cm⁻¹) and NO₂ is reduced to N₂O. At higher temperatures carboxylates interact with gaseous NO to carbonate, N₂O, CO and CO₂. The presence of niobium in the NbMCM-41 matrix enhances the oxidative properties of the catalysts and as a consequence the interaction between intermediates in NO reduction with propene in the oxygen excess. The co-precipitated AuNbMCM-41 exhibits higher NOx storage properties than the impregnated one.     

Influence of OSC Material on the Behaviour of Metallic Pd Catalysts in C2H4 and CO Oxidation as Well as in NO Reduction

The interaction of CO, C₂H₄, O₂, and NO reaction gas compounds over the metallic Pd/Al₂O₃ and Pd/OSC/Al₂O₃ monoliths was investigated in order to understand the behaviour of OSC material in the oxidation and reduction reactions. FT-IR gas analyser was used for the analysis of the product gas composition. Several activity experiments carried out with dissimilar feedstreams have revealed that the Ce _x Zr_1–x O₂ mixed oxide is an oxygen storage compound, which promotes CO and C₂H₄ oxidation as well as NO reduction in particular at low temperatures.     

Partial oxidation of methane over VOx/α-Al2O3 catalysts

The catalytic behavior of a series of VO_x/α-Al₂O₃ catalysts for the partial oxidation of methane has been evaluated. Samples with different vanadia loading were prepared from NH₄VO₃ and V(AcAc)₃. Characterization performed by TPR and oxygen uptake measurements indicates that different VO_x species are present on the samples. The catalytic patterns indicate that each V-surface species possesses different activity and selectivity. Isolated vanadates are the most active and selective towards HCHO, while V₂O₅ crystallites are detrimental to the catalytic performance.     

Surface properties and catalytic performance of La1−xSrxCrO3 perovskite-type oxides for CO and C3H6 combustion

Catalytic CO oxidation and C₃H₆ combustion have been studied over La_1−xSr_xCrO₃ (x = 0.0–0.3) oxides prepared by solid-state reaction and characterised by X-ray diffraction (XRD), nitrogen adsorption (BET analysis) and X-ray photoelectron spectroscopy (XPS). The expected orthorhombic perovskite structure of the chromite is observed for all levels of substitution. However, surface segregation of strontium along with a chromium oxidation process, leading to formation of Cr⁶⁺-containing phases, is produced upon increasing x and shown to be detrimental to the catalytic activity. Maximum activity is achieved for the catalyst with x = 0.1 in which mixed oxide formation upon substitution of lanthanum by strontium in the chromite becomes maximised.     

Properties of char particles obtained under O2/N2 and O2/CO2 combustion environments

Pulverized coal combustion in O₂/N₂ and O₂/CO₂ environments was investigated with a drop tube furnace. Results present that the reaction rate and burn-out degree of O₂/CO₂ chars (obtained in O₂/CO₂ environments) are lower than that of O₂/N₂ chars (obtained in O₂/N₂ environments) under the same experimental condition. It indicates that a higher O₂ concentration in O₂/CO₂ environment is needed to achieve the similar combustion characteristic to that in O₂/N₂ environment. The main differences between O₂/N₂ and O₂/CO₂ chars rely on the pore structure determined by N₂ adsorption and chemical structure measured by FT-IR. For O₂/CO₂ char, the surface is thick and the pores are compact which contribute to the fragmentation reduction of particles burning in O₂/CO₂ environment. The organic functional group elimination rate from the surface of O₂/CO₂ chars is slower or delayed. The present research results might have important implications for further understanding the intrinsic kinetics of pulverized coal combustion in O₂/CO₂ environment.     

Studies on oxidative coupling of methane using Sm2O3-based catalysts

The effects of Mn/Na₂WO₄, Li, and CaO loading on the monoclinic Sm₂O₃ catalyst were investigated for the oxidative coupling of methane using O₂ or N₂O as an oxidant. The catalysts were prepared by wet impregnation method and characterized by XRD, BET, CO₂-TPD, and XPS analysis. Impregnation of Mn/Na₂WO₄ on monoclinic Sm₂O₃ resulted in the formation of Sm_2?xMn_xO₃ phase, decreasing the catalytic performance. Li impregnation increased the C₂ selectivity but decreased the catalytic activity. The SmLiO₂ formation increased the catalytic activity and selectivity. High amounts of CaO impregnation increased the C₂ selectivity of monoclinic Sm₂O₃ without a loss in catalytic activity. 6Li/m-Sm₂O₃ were found unstable due to the Li loss from the catalyst. The 15CaO/m-Sm₂O₃ was quite stable and showed 8.2% ethylene yield with N₂O use, much higher than that was obtained with the well-known 2Mn/5Na₂WO₄/SiO₂ and 4Li/MgO catalysts. N₂O was more selective than O₂ as an oxidant and enhanced ethylene formation.     

Experimental study of ash formation during pulverized coal combustion in O2/CO2 mixtures

The present paper was addressed to mineral transformations and ash formation during O₂/CO₂ combustion of pulverized coal. Four Chinese thermal coals were burned in a drop tube furnace to generate ashes under various combustion conditions. The ash samples were characterized with XRD analysis and ⁵⁷Fe Mössbauer spectroscopy. The impacts of O₂/CO₂ combustion on mineral transformation and ash formation were explored through comparisons between O₂/CO₂ combustion and O₂/N₂ combustion. It was found that, O₂/CO₂ combustion did not significantly change the mineral phases formed in the residue ashes, but did affect the relative amounts of the mineral phases. The differences observed in the ashes formed in two atmospheres were attributed to the impact of the gas atmosphere on the combustion temperatures of coal char particles, which consequently influenced the ash formation behaviors of included minerals.