反应等离子喷涂TiC陶瓷增强金属复合涂层组织性能

采用前驱体碳化复合技术利用钛铁粉为原料制备Ti-Fe-Ni-C和Ti-Fe-C系粉末,并通过反应等离子喷涂技术(RPs)原位合成并沉积了Tic/Fe-Ni和TiC/Fe金属陶瓷复合涂层.利用XRD、SEM和EDS研究了复合粉末和不同基体涂层的成分、组织结构,测量了2种涂层的显微硬度和磨损量.结果表明:采用前驱体碳化复合技术制备的反应喷涂复合粉末粒度均匀、无有害相生成;制备的复合涂层由不同TiC颗粒含量的片层组织叠加而成;TiC颗粒大致呈球形,基体主要为Fe及Fe、Ni固溶体.Tic/Fe-Ni涂层较TiC/Fe涂层组织更加均匀、致密,且具有较高的显微硬度和较好的耐磨性.     

反应爆炸喷涂制备TiC／Fe-Ni金属陶瓷复合涂层

以钛铁粉、羰基镍粉和碳的前驱体(蔗糖)为原料,通过前驱体碳化复合技术制备Ti-Fe-Ni-C系反应热喷涂粉末,并通过爆炸喷涂技术原位合成并沉积TiC/Fe-Ni金属陶瓷复合涂层;利用XRD、SEM和EDS研究喷涂复合粉末和涂层的相组成、显微结构.结果表明:采用前驱体碳化复合技术制备的Ti-Fe-Ni-C反应喷涂复合粉末粒度均匀;所制备的TiC/Fe-Ni复合涂层由不同含量TiC颗粒分布于金属基体内部而形成的复合片层叠加而成,基体主要是(Fe,Ni)固溶体;TiC颗粒大致呈球形,粒度为纳米级;复合涂层的平均显微硬度HV0.2为18.9 GPa.     

反应火焰喷涂TiC/Fe复合涂层组织及形成机理

以TiFe粉和碳的前驱体（石油沥青）为原料通过前驱体碳化复合技术制备了Ti-Fe-C系反应喷涂复合粉末,并用普通火焰喷涂技术制备了TiC/Fe陶瓷金属复合涂层.观测了喷涂粉末、淬熄实验获取的飞行粒子以及涂层的形态、相和组织结构.结果表明：前驱体碳化复合Ti-Fe-C系喷涂粉末有非常紧密的结构;可有效的解决反应喷涂过程中原料粉末分离的问题.在反应火焰喷涂过程中,每一个喷涂粉末颗粒构成独立的微小反应单元,原料之间反应充分.在整个喷涂过程中喷涂粉末经历了熔化扩散、物相形成、碰撞后快速凝固三个阶段.所得涂层由TiC和Ti2O3共生聚集片层和细小TiC颗粒弥散分布于金属基体所形成的内晶型复合强化片层交替叠加而成.     

反应等离子喷涂TiC/Fe-Ni金属陶瓷复合涂层的显微组织

采用前驱体碳化复合技术制备Ti-Fe-Ni-C系粉末,并通过反应等离子喷涂技术（RPS）原位合成并沉积了TiC/Fe-Ni基金属陶瓷复合涂层。利用XRD、SEM和EDS研究复合粉末和涂层的成分、组织结构,考察复合粉末的TiC含量及复合粉末粒度对涂层组织结构的影响。结果表明：采用前驱体碳化复合技术制备的反应喷涂复合粉末粒度均匀、无有害相生成;TiC/Fe-Ni复合涂层由不同含量TiC颗粒分布于晶粒内部而形成的晶内型复合强化片层叠加而成,基体主要为（Fe、Ni）固溶体,TiC颗粒呈纳米级;涂层TiC含量较高时,纳米级TiC颗粒弥散分布更均匀;喷涂粉末粒度较大时,片层厚度较大,孔隙率较高。     

以沥青为前驱体制备TiC/FeCrNi反应火焰喷涂复合涂层

以钛铁粉、CrFe粉、羰基镍粉和碳的前驱体（石油沥青）为原料,通过前驱体碳化复合技术制备了Ti-Fe-Cr-Ni-C反应喷涂复合粉末,并通过普通火焰喷涂成功地合成与沉积了TiC/FeCrNi复合涂层.采用XRD和SEM对喷涂粉末和涂层的相组成和显微结构进行了分析,同时对涂层耐磨性能进行了对比研究.研究结果表明：采用前驱体碳化复合技术制备的Ti-Fe-Cr-Ni-C反应喷涂复合粉末粒度均匀、无有害相生成;所制备的TiC/FeCrNi复合涂层由不同含量TiC颗粒分布于金属基体内部而形成的复合强化片层叠加而成,TiC颗粒呈纳米级;基体由（Fe,Cr）和Cr0.19Fe0.7Ni0.11两相组成;相同条件下,所获TiC/FeCrNi复合涂层磨损体积大约是常规火焰喷涂Ni60涂层的1/8.     

TiC/Fe-Ni金属陶瓷复合涂层反应等离子喷涂研究

以钛铁粉、镍粉、铁粉和碳的前驱体(蔗糖)为原料采用前驱体碳化复合技术制备了Ti-Fe-Ni-C系反应热喷涂粉末,并通过等离子喷涂(RPS)技术原位合成并沉积了TiC/Fee-Ni金属陶瓷复合涂层.采用XRD、SEM和EDS对喷涂粉末和涂层的成分、组织结构进行了分析.研究表明该反应喷涂粉末粒度均匀、无有害相生成;所得涂层由不同TiC颗粒含量的TiC/Fe-Ni复合片层组成;TiC颗粒大致呈球形,粒度呈纳米级;所获涂层在相同条件下耐磨性是Ni60涂层的7倍.     

C/Ti原子比对前驱体碳化复合等离子熔覆TiC/Fe复合涂层的影响

以钛铁粉和碳的前驱体(蔗糖)为原料通过前驱体碳化复合技术制备了Ti-Fe-C等离子熔覆复合粉末,并通过等离子熔覆技术在普通低碳钢表面成功地原位合成了TiC/Fe陶瓷金属复合涂层.着重研究了不同C/Ti原子比对等离子熔覆TiC/Fe复合涂层的相组成、显微结构和硬度的影响.结果表明,前驱体碳化复合技术制备的Ti-Fe-C系等离子熔覆复合粉末中C/Ti原子比是影响涂层相组成、显微结构和硬度的关键因素.C/Ti原子比不同,涂层的相组成和硬度不同;随着C/Ti原子比增大,涂层中TiC团聚富集区增大,涂层的孔隙率也随之增大.     

以蔗糖为前驱体火焰喷涂原位TiC增强Ni基复合涂层的制备

以蔗糖为碳源,采用前驱体热分解技术制备Ni-Ti-C系反应热喷涂混合粉末,通过氧乙炔火焰喷涂技术合成并同时沉积原位TiC颗粒增强的Ni基合金复合涂层.利用XRD和SEM研究混合粉末和涂层的相成分和组织结构,分析TiC/Ni复合涂层的硬度和耐磨性.结果表明:反应火焰喷涂TiC/Ni复合涂层主要由TiC和Ni基体组成,并含少量的Ni3Ti和Ti3O5;涂层由复合强化片层相瓦叠加而成,复合强化片层中TiC颗粒均匀分布于Ni基体中,TiC颗粒呈球形,粒度达到亚微米级:涂层具有较高的硬度和耐磨性,复合强化片层显微硬度为FIV0.21433,涂层的耐磨性能远优于基板材料45号钢和对比涂层Ni60的耐磨性.     

以蔗糖为前驱体制备反应等离子熔覆高铬铁基复合涂层

以铁、铬、钨、镍粉末和碳的前驱体(蔗糖)为原料通过碳化制备了反应等离子熔覆Fe-Cr-C-W-Ni复合粉末,采用同步送粉反应等离子熔覆设备和优化的反应等离子熔覆工艺,在调质C蕉钢(C≤0.35%)基材表面制备了高铬铁基复合涂层.结果表明,采用前驱体碳化复合技术制备的Fe-Cr-C-W-Ni复合粉末粒度均匀、无有害相生成;熔覆所得到的涂层以(Cr,Fe)7C3/γ共晶为基体,其上分布大量的(Cr,Fe)7C3初生相.涂层与基材界面为完全冶金结合.涂层断面上的平均显微硬度约为1 100 HV.相同条件下所获涂层的磨损体积大约是常规等离子熔覆Ni60涂层的1/7.     

WC/FeAl金属间化合物基金属陶瓷涂层的冷喷涂制备

采用WC/Fe/Al混合粉末,通过机械合金化制备40v0l％ WC/Fe(Al)固溶体复合粉末,利用冷喷涂沉积涂层并结合热处理原位反应制备了WC/FeAl金属间化合物基金属陶瓷涂层.研究了球磨时间对复合粉末相结构、晶粒尺寸及组织结构的影响,并分析了冷喷涂WC/FeAl金属间化合物基金属陶瓷涂层的组织和显微硬度.结果表明,机械合金化可获得WC陶瓷颗粒呈微/纳米多尺度分布的WC/Fe(Al)金属陶瓷复合粉末,球磨36 h的复合粉末基体相平均晶粒尺寸约为90 nm,冷喷复合涂层组织致密、多尺度WC颗粒在基体中均匀弥散分布,涂层显微硬度约为1060 HV0.3,涂层在650℃热处理后发生Fe(Al)固溶体向FeAl金属间化合物的原位转变,制备出了WC/FeAl金属间化合物基金属陶瓷涂层.     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。