Electrodeposition of <Emphasis Type="Italic">p</Emphasis>-Type Sb<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Te<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> Thermoelectric Films

Thermoelectric Sb _x Te _y films were potentiostatically electrodeposited in aqueous nitric acid electrolyte solutions containing different concentrations of TeO₂. Stoichiometric Sb _x Te _y films were obtained by applying a voltage of −0.15 V versus saturated calomel electrode (SCE) using a solution consisting of 2.4 mM TeO₂, 0.8 mM Sb₂O₃, 33 mM tartaric acid, and 1 M HNO₃. The nearly stoichiometric Sb₂Te₃ films had a rhombohedral structure, R[`3]m R\bar{3}m , with a preferred orientation along the (015) direction. The films had hole concentration of 5.8 × 10¹⁸/cm³ and exhibited mobility of 54.8 cm²/Vs. A more negative potential resulted in higher Sb content in the deposited Sb _x Te _y films. Furthermore, it was observed that the hole concentration and mobility decreased with increasingly negative deposition potential, and eventually showed insulating properties, possibly due to increased defect formation. The absolute value of the Seebeck coefficient of the as-deposited Sb₂Te₃ thin film at room temperature was 118 μV/K.     

An ultra-low-power CMOS symmetrical OTA for low-frequency <Emphasis Type="Italic">G</Emphasis><Subscript><Emphasis Type="Italic">m</Emphasis></Subscript>-<Emphasis Type="Italic">C</Emphasis> applications

In this paper an ultra-low-power CMOS symmetrical operational transconductance amplifier (OTA) for low-frequency G _m -C applications in weak inversion is presented. Its common mode input range and its linear input range can be made large using DC shifting and bulk-driven differential pair configuration (without using complex approaches). The symmetrical OTA was successfully verified in a standard CMOS 0.35-μm process. The measurements show an open loop gain of 61 dB and a unit gain frequency of 195 Hz with only 800 mV of power supply voltage and just 40 nW of power consumption. The transconductance is 66 nS, which is suitable for low-frequency G _m -C applications.     

Sectoral transition between modes <Emphasis Type="Italic">H</Emphasis><Subscript>10</Subscript> and <Emphasis Type="Italic">H</Emphasis><Subscript>01</Subscript>

The excitation of main parasitic modes E ₁₁, H ₁₁, and H ₂₁, which have cutoff sections in a sectoral transition between modes H ₁₀ and H ₀₁, is investigated. It is shown that, for magnetic modes, including modes H ₁₁ and H ₂₁, it is unnecessary to use the Airy equation and that this circumstance simplifies the design relationships. The energies of these modes are calculated as functions of the transition parameters.     

Ab initio calculations of phonon spectra of (GaP)<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript>(AlP)<Subscript><Emphasis Type="Italic">m</Emphasis></Subscript> superlattices

Using the method of linear response, vibrational spectra and densities of states of GaP and AlP crystals and monolayer GaP/AlP superlattices are calculated. Phonon modes of (GaP) _n (AlP) _m superlattices with various numbers of monolayers are calculated for the center of the Brillouin zone. The obtained results are compared with the Raman scattering data and the effect of nonideality of the interface on phonon frequencies is discussed.     

Surface states on the <Emphasis Type="Italic">n</Emphasis>-InN-electrolyte interface

Dependences of differential capacitance of the electrolyte-n-InN (0001) contact on the bias voltage are studied. Their analysis of the basis of a model similar to a model of the MIS structure shows that the energy spectrum of surface states of InN above the conduction band bottom can be represented by two, relatively narrow, bands of deep levels described by the Gaussian distribution. Parameters of these bands are as follows: the average energy counted from the conduction band bottom, ΔE ₁ ≈ 0.15 eV and ΔE ₂ ≈ 0.9 eV; and the mean-square deviation, ΔE ₁ ≈ 0.15–0.25 eV and ΔE ₂ ≈ 0.05–0.1 eV. The total density of states in the bands are (1–2.5) × 10¹² and (0.2–4) × 10¹² cm^–2.     

Phonon-Assisted Tunneling from <Emphasis Type="Italic">Z</Emphasis><Subscript>1</Subscript>/<Emphasis Type="Italic">Z</Emphasis><Subscript>2</Subscript> in 4H-SiC

n-Type 4H-SiC bulk samples with a net doping concentration of 2.5 × 10¹⁷ cm⁻³ were irradiated at room temperature with 1-MeV electrons. The high doping concentration plus a reverse bias of up to −13 V ensures high electric field in the depletion region. The dependence of the emission rate on the electric field in the depletion region was measured using deep-level transient spectroscopy (DLTS) and double-correlation deep-level transient spectroscopy (DDLTS). The experimental data are adequately described by the phonon-assisted tunneling model proposed by Karpus and Pere.     

3<Emphasis Type="Italic">C</Emphasis>-SiC <Emphasis Type="Italic">p-n</Emphasis> structures grown by sublimation on 6<Emphasis Type="Italic">H</Emphasis>-SiC substrates

Sublimation epitaxy in a vacuum has been employed to grow n-and p-type 3C-SiC layers on 6H-SiC substrates. Diodes have been fabricated on the basis of the p-n structure obtained, and their parameters have been studied by measuring their current-voltage and capacitance-voltage characteristics and by applying the DLTS and electroluminescence methods. It is shown that the characteristics of the diodes studied are close to those of diodes based on bulk 3C-SiC. A conclusion is made that sublimation epitaxy can be used to fabricate 3C-SiC p-n structures on substrates of other silicon carbide polytypes.     

Dual-Frequency Behavior of Stacked High <Emphasis Type="Italic">T</Emphasis><Subscript><Emphasis Type="Italic">c</Emphasis></Subscript> Superconducting Microstrip Patches

The dual-frequency behavior of stacked high T _c superconducting rectangular microstrip patches fabricated on a two-layered substrate is investigated using a full-wave spectral analysis in conjunction with the complex resistive boundary condition. Using a matrix representation of each layer, the dyadic Green’s functions of the problem are efficiently determined in the vector Fourier transform domain. The stationary phase method is used for computing the radiation electric field of the antenna. The proposed approach is validated by comparison of the computed results with previously published data. Variations of the lower and upper resonant frequencies, bandwidth and quality factor with the operating temperature are given. Results showing the effects of the bottom patch thickness as well as the top patch thickness on the dual-frequency behavior of the stacked configuration are also presented and discussed. Finally, for a better comprehension of the dual-frequency operation, a comparison between the characteristics of the lower and upper resonances is given.     

Modulation SQUID electronics working with high-<Emphasis Type="Italic">T</Emphasis><Subscript><Emphasis Type="Italic">c</Emphasis></Subscript> SQUIDs in open space

SQUID electronics optimized for operation in unshielded space with dc high-T _c superconducting quantum interference devices (HTS SQUIDs) are developed, manufactured, and studied. The dynamic characteristics of the SQUID electronics are studied with two magnetic-field sensors based on the HTS SQUIDs: a conventional SQUID sensor with a resolution of 100 fT/Hz^1/2 and a supersensitive SQUID sensor with a resolution of 15 fT/Hz^1/2 at frequencies exceeding 10 Hz and a resolution of 30 fT/Hz^1/2 at a frequency of 1 Hz. Stable operation of the magnetometric channel is demonstrated with both SQUID sensors under urban conditions. On the basis of a complex programmable logic device (CPLD), an ac bias can be realized in the SQUID and the modulation signal can be compensated in the feedback, bias-current, and desired-signal circuits. Such a compensation system is the most appropriate and versatile means of providing stable operation of the magnetometric channel in the presence of the SQUID ac bias, regardless of the type of high-temperature sensor and the configuration of the input contacts in the measurement probe.     

Mechanisms of charge transport in anisotype <Emphasis Type="Italic">n</Emphasis>-TiO<Subscript>2</Subscript>/<Emphasis Type="Italic">p</Emphasis>-CdTe heterojunctions

Surface-barrier anisotype n-TiO₂/p-CdTe heterojunctions are fabricated by depositing thin titanium-dioxide films on a freshly cleaved surface of single-crystalline cadmium-telluride wafers by reactive magnetron sputtering. It is established that the electric current through the heterojunctions under investigation is formed by generation-recombination processes in the space-charge region via a deep energy level and tunneling through the potential barrier. The depth and nature of the impurity centers involved in the charge transport are determined.     

<Emphasis Type="Italic">p</Emphasis><Superscript>+</Superscript>-Si-<Emphasis Type="Italic">n</Emphasis>-CdF<Subscript>2</Subscript> heterojunctions

Boron diffusion and the vapor-phase deposition of silicon layers are used to prepare ultrashallow p⁺-n junctions and p⁺-Si-n-CdF₂ heterostructures on an n-CdF₂ crystal surface. Forward portions of the I–V characteristics of the p⁺-n junctions and p⁺-Si-n-CdF₂ heterojunctions reveal the CdF₂ band gap (7.8 eV), as well as allow the identification of the valence-band structure of cadmium fluoride crystals. Under conditions in which forward bias is applied to the p⁺-Si-n-CdF₂ heterojunctions, electroluminescence spectra are measured for the first time in the visible spectral region.     

Photoconversion in <Emphasis Type="Italic">n</Emphasis>-ZnO:Al/Pd<Emphasis Type="Italic">Pc/p</Emphasis>-CuIn<Subscript>3</Subscript>Se<Subscript>5</Subscript> structures

n-ZnO:Al/PdPc/p-CuIn₃Se₅ photosensitive structures have been proposed and fabricated for the first time by vacuum sublimation of palladium phthalocyanine on the surface of wafers of the ternary semiconductor compound CuIn₃Se₅ and by magnetron sputtering of n-ZnO:Al films on the surface of palladium phthalocyanine films. The current-voltage characteristics and spectra of the photoconversion quantum efficiency of the obtained structures are investigated. It is shown that these structures can be used as multiband white-light converters.     

Ultra-wideband horn antennas with a considerable difference in radiation pattern width in <Emphasis Type="Italic">E</Emphasis>- and <Emphasis Type="Italic">H</Emphasis>-planes

The paper presents results of theoretical and experimental investigation of ultra-wideband horn antennas with a rectangular aperture and input formed by a symmetric H-waveguide. The antennas show a considerable difference in their radiation pattern widths in the E-and H-planes, and good matching properties in a range of frequencies from 1 to 10 GHz. The required difference between radiation patterns of the antennas is attained by proper selection of horns’ geometry and application of a diverging dielectric lens in each horn. Optimal profiles of the horn antenna generatrix and of the dielectric lens placed inside are determined. Reliability of results of the theoretical analysis is confirmed by testing the designed prototypes of the ultra-wideband H-sectorial and E-sectorial horns.     

High-efficiency LEDs based on <Emphasis Type="Italic">n</Emphasis>-GaSb/<Emphasis Type="Italic">p</Emphasis>-GaSb/<Emphasis Type="Italic">n</Emphasis>-GaInAsSb/<Emphasis Type="Italic">P</Emphasis>-AlGaAsSb type-II thyristor heterostructures

A new type of light-emitting diodes (LEDs), a high-efficiency device based on an n-GaSb/p-GaSb/n-GaInAsSb/P-AlGaAsSb thyristor heterostructure, with the maximum emission intensity at wavelength λ = 1.95 μm, has been suggested and its electrical and luminescent characteristics have been studied. It is shown that the effective radiative recombination in the thyristor structure in the n-type GaInAsSb active region is provided by double-sided injection of holes from the neighboring p-type regions. The maximum internal quantum efficiency of 77% was achieved in the structure under study in the pulsed mode. The average optical power was as high as 2.5 mW, and the peak power in the pulsed mode was 71 mW, which exceeded by a factor of 2.9 the power obtained with a standard n-GaSb/n-GaInAsSb/P-AlGaAsSb LED operating in the same spectral range. The approach suggested will make it possible to improve LED parameters in the entire mid-IR spectral range (2–5 μm).     

Temperature dependence of the band structure of 3<Emphasis Type="Italic">C</Emphasis>, 2<Emphasis Type="Italic">H</Emphasis>, 4<Emphasis Type="Italic">H</Emphasis>, and 6<Emphasis Type="Italic">H</Emphasis> SiC polytypes

The temperature dependences of significant energy extrema at the high-symmetry points Γ, X, L, K, M, A, and H of the Brillouin zone in the cubic and hexagonal modifications of SiC, as well as the energies of the main interband transitions at these points, were calculated for the first time by the empirical-pseudopotential method. The effect of the temperature dependence of the electron-phonon interaction on the crystal band structure was taken into account via the Debye-Waller factors, and the contribution of the linear expansion of the lattice was accounted for via the temperature dependence of the linear-expansion coefficient. The special features of the temperature dependences of the energy levels and of energies of the interband and intraband transitions are analyzed in detail. The results of the calculations are in good agreement with the known experimental data on the characteristics of SiC-based p-n structures operating in the breakdown mode. For example, the temperature coefficient of the energy of the X_1c–X_3c transition, which is responsible for the narrow violet band in the breakdown-electroluminescence spectra of reverse-biased p-n junctions, was found to be significantly smaller than the temperature coefficients for the interband transitions (from the conduction to valence band). This fact is quite consistent with the experimental curve of the temperature coefficient of the emission spectrum, which has a minimum in the same wavelength range.     

Structural and Luminescent Properties of SiO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>N<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>(Si) Nanocomposite Films

With a view to creating Si LEDs, the structural and luminescent properties of SiO _x N _y films containing Si nanocrystals in the SiO _x N _y matrix are studied experimentally. It is found that the film structure (nanocrystal size and concentration, the presence of an amorphous phase, etc.) and the spectrum and intensity of photoluminescence (PL) and electroluminescence (EL) are strongly dependent on the Si stoichiometric excess δ and annealing conditions. At δ≈ 10%, unannealed films are amorphous and contain Si clusters of size < 2 nm, as deduced from the TEM and microdiffraction data obtained. Annealing at 800–1000°C for 10–60 min produces Si crystals 3–5 nm in size with a concentration of ≈10¹⁸ cm^?3. The annealed films exhibit room-temperature PL and EL over the wavelength range 400–850 nm with intensity peaks located at 50–60 and 60–70 nm, respectively. The PL and EL spectra are found to be qualitatively similar. This suggests that both the PL and the EL should be associated with the formation of luminescent centers at nanocrystal–matrix interfaces and in boundary regions. However, the two phenomena should differ in the mechanism by which the centers are excited. With the EL, excitation should occur by impact processes due to carrier heating in high electric fields. It is found that as δ increases, so does the proportion of large amorphous Si clusters with a high density of dangling bonds. This enhances nonradiative recombination and suppresses luminescence.     

Study of the layer-substrate interface in <Emphasis Type="Italic">nc</Emphasis>-Si-SiO<Subscript>2</Subscript>-<Emphasis Type="Italic">p</Emphasis>-Si structures with silicon quantum dots by the method of temperature dependences of photovoltage

Layers grown by magnetron deposition of Si and SiO₂ on a p-type silicon substrate and containing silicon nanocrystals in the oxide matrix have been studied by the method of temperature dependences of the capacitive photovoltage. The effect of the substrate orientation and natural oxidation preceding high-temperature annealing that results in the formation of Si nanocrystals in the SiO₂ matrix on the layer-substrate interface characteristics is studied. The density of fast interface states trapping majority carriers was estimated. It is found that structural changes occur at the layer-substrate interface in the case of a (111) substrate and are caused by stresses appearing upon cooling. It was shown that natural oxidation of the deposited layer, preceding high-temperature annealing, causes an increase in the charge trapped in the oxide.     

Sommerfeld wave (<Emphasis Type="Italic">E</Emphasis><Subscript>00</Subscript> wave) propagating along the cylindrical conductor with a large radius

The technique of solving the dispersion equation for the E ₀₀ wave (Sommerfeld wave), which propagates through a cylindrical conductor with large radius a and finite conductivity σ₁ in the presence of a surrounding lossy dielectric, has been developed. The presented numerical results are obtained by calculating a cylinder with the earth radius and sea water parameters at the frequencies f = 0.0500−0.9554 MHz. It is shown that f ₀ = 0.9554 MHz is the limiting frequency.