4×155Mb／s频分复用（FDM）光纤通信系统的研究

报道了一个无故障工作时间大于２４小时的四路１５５Ｍｂ／ｓ频分复用（ＦＤＭ）光纤通信系统，实测系统误码率优于０×１０（－１４）。系统接收机包括解复用光滤波器，接收机灵敏度优于－３０ｄＢｍ（ＢＥＲ＝１×１０（－９），频道间距为０．１ｎｍ，四路ＦＤＭ信号－２０ｄＢ的总谱宽为０．７ｎｍ。系统采用国产ＤＦＢ激光器为光源，实际光纤传输距离１８ｋｍ。系统全部实现了脱离光学平台的模块化结构，在长期的系统实验中显示了优良的稳定性。这一成果为ＦＤＭ在光纤传输接入网中的进一步实用化开发铺平了道路。     

抑制等信道间距陆上干线光纤通信系统中光纤色散和四波混频效应的新方案

提出了一种用以克服等信道间距划分、波分复用（ＷＤＭ）＋掺饵光纤放大器（ＥＤＦＡ）陆上光纤通信系统中光纤色散和四波混频（ＦＷＭ）效应的新方案。采用１５５０ｎｍ处色散为－２．８９ｐｓ／ｋｍ／ｎｍ的小色散单模光纤（ｓｍａｌｌ－ｄｉｓｐｅｒｓｉｏｎｓｉｎｇｌｅ－ｍｏｄｅ－ｆｉｂｅｒ，ＳＤＳＭＦ）可避免严重的ＦＷＭ效应，同时利用ＩＴＵ－ＴＧ．６５２非色散位移光纤（ｎｏｎ－ｄｉｓｐｅｒｓｉｏｎ－ｓｈｉｆｔｅｄｆｉｂｅｒ，ＮＤＳＦ），在ＥＤＦＡ整个带宽范围内（１５３０～１５７０ｎｍ）补偿ＳＤＳＭＦ引入的负色散。采用此方案，一个１０路×１０Ｇｂ／ｓ、１０级ＥＤＦＡ级联的等信道间距（１ｎｍ）光纤通信系统，经近千公里的光纤传输后，ＦＷＭ和色散引入的恶化量将分别小于１ｄＢ。     

8频道151公里全光波分复用准工程化光纤通信系统

拥有８个频道、传输距离为１５１公里、使用二个光纤放大器和工程化端机的全光波分复用光纤通信系统在北京大学研制成功。该系统在长期工作状态下各频道的误码率在１．６×１０（－１２）至０×１０（－１５）（即单频道连续测量１５天无误码）之间。该系统使用计算机对波长进行智能控制并监视该系统的工作状态。各频道波长分别是１５３１ｎｍ，１５３３ｎｍ，１５３５ｎｍ，１５３７ｎｍ，１５３９ｎｍ，１５４３ｎｍ，１５４５ｎｍ和１５４９ｎｍ。每频道传输码率为１４０Ｍｂ／ｓ，传输码型为１Ｂ１ＨＣＭ１ＰＲＢＳ。因此该系统总传输码率可以达到２．２Ｇｂ／ｓ（即２８０Ｍｂ／ｓ×８）。经过长时间开机检测，该系统已经接近于工程使用要求。     

1.48μm泵浦EDFA的研制及其在模拟光纤传输系统中的应用

利用国产１．４８μｍ泵浦ＬＤ和优质掺饵光纤研制了一种实用化的掺饵光纤放大器，小信号净增益２８ｄＢ，噪声系数５．１ｄＢ，增益谱宽大于２０ｎｍ，最大输出功率达４．８ｄＢｍ和１１ｄＢｍ。实验研究了ＥＤＦＡ在ＦＭ／ＦＤＭ模拟电视光纤系统的应用，利用ＥＤＦＡ作为系统的功率提升和中继放大器，分别成功地进行了１８５ｋｍ和２２４ｋｍ的系统传输试验。     

4×622Mb／s密集波分复用282Km无再生中继光纤传输实验

介绍了８６３计划光电子主题光电子器件试验床（Ｔｅｓｔｂｅｄ）的概况及其最新的实验结果。采用４只国产ＤＦＢ激光器组件为光源、３台国内研制的掺铒光纤放大器作级联放大，实现了在１５５０ｎｍ波段、４路６２２Ｍｂ／ｓ信道、相邻信道波长间隙为２ｎｍ的２８２Ｋｍ单模光纤无再生中继传输，系统误码率优于１×１０－１２。实验表明，随着我国高性能的量子阱半导体激光器和掺铒光纤放大器的研制成功，进行下一代光纤通信技术的研究，包括开展具有多级掺铒光纤放大器放大的高速大容量波分复用光纤通信系统的研制和开发已有了坚实的基础。     

使用光纤放大器的频分复用光纤传输系统

报道了一个使用光纤放大器的两路非相干频分复用光纤传输实验系统。系统采用国产ＤＦＢ激光器作光源，用意大利生产的光纤放大器作在线放大器，用自制的光学谐振腔作光学滤波器和解复用器，采用ＦＳＫ调制制式，将１４０Ｍｂ／ｓ非归零伪随机码传输了５０公里，得到了很好的眼图。在频道间距为１０ＧＨｚ情况下，未观测到邻道干扰和光纤放大器的非线性现象。     

109公里2.5Gb／s无中继IM／DD光纤传输实验系统

对国内首次２．４８８Ｇｂ／ｓ光纤传输系统实现结果进行了报道。系统工作波长１５５０ｎｍ，利用常规单模光纤实现了１０９公里无中继传，要用ＩＭ／ＤＤ方式，接收机灵敏度为－３０．５ｄＢｍ．     

采用DFB＋MZ调制器组件为光源的10Gb／s100kmG.652光纤传输实验研究

报道了运用ＤＦＢ－ＬＤ与Ｍ－Ｚ调制器单片集成组件为光源实现１０Ｇｂ／ｓ１００ｋｍ常规单模光张的传输实验。实验表明,采用光源预啁啾技术可延长系统的传输距离。在误码率ＢＥＲ＝１０＾－１０时,传输后的功率代价为１．１ｄＢ,接收灵敏度为－１６．５ｄＢｍ。这一结果达到了国外同类实验的水平。     

高性能2.5Gb／s用的DFB—LD／EA单片集成器件

报导了采用全ＭＯＣＶＤ生长的１．５５μｍ的单片集成ＤＦＢ＝ＬＤ／ＥＡ组件的 在ＤＷＤＭ系统上的传输测试结果，出纤功率Ｐｆ≥２．５ｍＷ＠Ｉｆ＝７５ｍＡ，边模抑制比ＳＭＳＲ〉３５ｄＢ，调制器反向偏压为２．５Ｖ时的消光比为１４ｄＢ，该发射模块在２．５Ｇｂ／ｓＤＷＤＭ系统上进行了传输试验，传输２４０Ｋｍ后无误码，其通道代价≤１ｄＢ＠ＢＥＲ＝１０＾－１２。     

利用光纤非线性环镜实现8×2.5Gb/s→2.5Gb/s解复用及误码特性的测量

报道了利用３ｋｍ 光纤非线性环镜作为全光解复用器对８×２５Ｇｂ／ｓ光时分复用信号的解复用实验结果, 并对２５Ｇｂ／ｓ解复用信号进行了误码特性的测量。测量结果表明误码率可达到１０－ １１, 误码率为１０－ ９时的功率代价仅为１４ｄＢ。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...