Development and analysis of a folded shorted-patch antenna with reduced size

The length of a wall-shorted rectangular patch antenna can be reduced from /spl sim//spl lambda//sub 0//4 to /spl sim//spl lambda//sub 0//8 by a simple folding operation, which results in a stacked shorted-patch (S-P) structure with a resonant frequency that can be controlled by modifying the distance between the stacked (lower and upper) shorted-patches. A theoretical analysis based on a simple transmission-line model is presented and compared with numerical simulations, showing good agreement if the height of the folded patch is much smaller than the patch length. The physical insight of the variation of the resonant frequency for this reduced-size antenna can be understood by considering the antenna as a shorted patch loaded with a capacitor. An experimental verification is carried out for a 15 mm/spl times/15 mm/spl times/6 mm folded S-P antenna prototype designed for the 2.4 GHz ISM band that can achieve a 10-dB return loss bandwidth of 4% and results in a nearly omni-directional radiation pattern.     

Composite right/left-handed transmission line based compact resonant antennas for RF module integration

Several electrically small resonant antennas employing the composite right/left-handed transmission line (CRLH-TL) are presented for integration with portable RF modules. The proposed antenna designs are based on the unique property of anti-parallel phase and group velocity of the CRLH-TL at its fundamental mode. In this mode, the propagation constant increases as the frequency decreases, therefore, a small guided wavelength can be obtained at a lower frequency to provide the small /spl lambda//sub g//2 resonant length used to realize a compact antenna design. Furthermore, the physical size and the operational frequency of the antenna depend on the unit cell size and the equivalent transmission line model parameters of the CRLH-TL, including series inductance, series capacitance, shunt inductance and shunt capacitance. Optimization of these parameters as well as miniaturization techniques of the physical size of unit cell is investigated. A four unit-cell resonant antenna is designed and tested at 1.06 GHz. The length, width and height of the proposed antenna are 1/19/spl lambda//sub 0/, 1/23/spl lambda//sub 0/ and 1/83/spl lambda//sub 0/, respectively. In addition, a compact antenna using a 2-D three by three mushroom like unit cell arrangement is developed at 1.17 GHz, showing that an increased gain of 0.6 dB and higher radiation efficiency can be achieved over the first prototype antenna. The same design is applied in the development of a circularly polarized antenna operating at 2.46 GHz. A 116/spl deg/ beamwidth with axial ratio better than 3 dB is observed. The physical size of the proposed mushroom type small antenna and the circularly polarized antenna is 1/14/spl lambda//sub 0/ by 1/14/spl lambda//sub 0/ by 1/39/spl lambda//sub 0/ and 1/10/spl lambda//sub 0/ by 1/10/spl lambda//sub 0/ by 1/36/spl lambda//sub 0/, respectively.     

A novel approach for miniaturization of slot antennas

With the virtual enforcement of the required boundary condition (BC) at the end of a slot antenna, the area occupied by the resonant antenna can be reduced. To achieve the required virtual BC, the two short circuits at the end of the resonant slot are replaced by some reactive BC, including inductive or capacitive loadings. The application of these loads is shown to reduce the size of the resonant slot antenna for a given resonant frequency without imposing any stringent condition on the impedance matching of the antenna. A procedure for designing this class of slot antennas for any arbitrary size is presented. The procedure is based on an equivalent circuit model for the antenna and its feed structure. The corresponding equivalent circuit parameters are extracted using a full-wave forward model in conjunction with a genetic algorithm optimizer. These parameters are employed to find a proper matching network so that a perfect match to a 50 /spl Omega/ line is obtained. For a prototype slot antenna with approximate dimensions of 0.05/spl lambda//sub 0//spl times/0.05/spl lambda//sub 0/ the impedance match is obtained, with a fairly high gain of -3dBi, for a very small ground plane (/spl ap/0.20/spl lambda//sub 0/). Since there are neither polarization nor mismatch losses, the antenna efficiency is limited only by the dielectric and ohmic losses.     

Elliptical planar monopole antenna with extremely wide bandwidth

A planar monopole antenna with an extremely wide bandwidth is introduced, which is composed of an elliptical monopole patch and a trapeziform ground plane, both printed on the same side of a substrate, and is fed by a tapered CPW feeder in the middle of the ground plane. The simulated and experimental results demonstrate that this antenna achieves a ratio impedance bandwidth of 21.6:1 for VSWR/spl les/2, and exhibits a nearly omnidirectional radiation pattern, while its area is only about 0.19/spl lambda//sub l//spl times/0.16/spl lambda//sub l/ where /spl lambda//sub l/ is the wavelength of the lowest operating frequency.     

2 GHz electromagnetic crystal reflector antenna

The radiation pattern of a monopole antenna with a small electromagnetic crystal (EMXT) reflector was investigated. High frequency structure simulations predict a considerable amount of near-field shielding with undisturbed antenna impedance matching when a perfect magnetic conductor reflector is positioned near the monopole. The pattern distortion created by the reflector gradually decreases, reaching a minimum in the far field. Experimental results show the monopole with an EMXT reflector, /spl lambda//sub 0//4/spl times//spl lambda//sub 0//2 in size, produces a radiation pattern with a front-to-back ratio of 10.8 and 5.7 dB in the near and far fields, respectively.     

A cavity-backed rectangular aperture antenna with application to a tilted fan beam array antenna

A rectangular aperture of A/sub x//spl times/A/sub y/, cut in the top conducting plate of a triplate transmission line and backed by a cavity, radiates a tilted beam off the direction normal to the aperture. The mechanism of the radiation is explained using the Poynting vector distribution above the aperture and the phase distribution of the electric field over the aperture. The tilt angle is calculated as a function of side length A/sub x/ for a representative value of A/sub y/=18 mm=0.747/spl lambda//sub 12.45/, where /spl lambda//sub 12.45/ is the wavelength at a test frequency of 12.45 GHz. A tilted beam of approximately 27/spl deg/ is realized at A/sub x//A/sub y/=8/9 with a gain of approximately 8 dB. Using this value of A/sub x//A/sub y/, an array antenna composed of rectangular cavity-backed aperture elements is investigated. The array forms a tilted fan beam without phase shifters. The frequency responses of the gain and input impedance are discussed.     

CLIP antenna for wireless bluetooth applications

In this paper, a novel design for a coplanar waveguide antenna is developed that consists of two U-shaped slots. The antenna is named CLIP. The antenna was designed for a central frequency of 2.4 GHz, with an input impedance of 50 /spl Omega/. The antenna dimensions represent a 72% size reduction compared to a conventional microstrip rectangular-patch antenna. The measured antenna bandwidth was about 11%, while its gain was about 17 dB. These values are fairly acceptable in all wireless communication systems. The antenna configuration has a bidirectional radiation pattern, while a unidirectional radiation pattern was achieved by using a /spl lambda//sub 0//4 reflector with a metal plate. A 2/spl times/2 multi-element sub array was implemented to widen the application area. The mutual coupling between adjacent elements was low. Orthogonal-plane coupling between adjacent elements was introduced to increase the reduction in the mutual coupling. The mutual coupling level was reduced to less than -23 dB in all coupling planes. The CLIP antenna element and arrays were fabricated. Experimental measurements showed very good performance, which agreed well with simulation results.     

Multilayer spatial angular filter with airgap tuners to suppress grating lobes of 4/spl times/1 array antenna

A multilayer spatial angular filter with airgap tuners to suppress the grating lobes of a 4/spl times/1 array antenna is proposed. By using the airgap tuner, a commercial standard substrate can be chosen for the filter, to achieve its resonance condition, instead of /spl lambda//sub g//4 substrate. The measured beam patterns of the 4/spl times/1 array with the filter show that the grating and sidelobes are effectively diminished by 15 to 30 dB in the region of interest.     

Design of an efficient miniaturized UHF planar antenna

The design aspects and the measured results of a novel miniaturized planar antenna are described. Such architectural antenna design is of great importance in mobile military communications where low visibility and high mobility are required. Slot radiating elements, having a planar geometry and capable of transmitting vertical polarization when placed nearly horizontal, are appropriate for the applications at hand. Slot antennas also have another useful property, so far as impedance matching is concerned. Basically, slot dipoles can easily be excited by a microstrip line and can be matched to arbitrary line impedances simply by moving the feed point along the slot. Antenna miniaturization can be achieved by using a high permittivity or permeability substrate and superstrate materials and/or using an appropriate antenna topology. We demonstrate miniaturization by designing an appropriate geometry for a resonant narrow slot antenna. A very efficient radiating element that occupies an area as small as 0.12/spl lambda//sub 0//spl times/0.12/spl lambda//sub 0/ is designed and tested. Simulation results, as well as the measured input impedance and radiation patterns of this antenna, are presented. This structure shows a measured gain of 0.5 dBi on FR4 substrate, which has a loss-tangent of the order of 0.01. Also, the effect of finite ground plane size on gain and resonant frequency is investigated experimentally.     

Investigations on miniaturized endfire vertically polarized quasi-fractal log-periodic zigzag antenna

This paper presents the investigations on a miniaturized vertically polarized traveling wave antenna for operation in the high frequency band (3-6 MHz), with a specific requirement of keeping its height near 1/8th of a wavelength. The antenna is desired to have a good endfire gain and front to back ratio, and small radiation levels in the vertical direction at broadside angle. A log-periodic Zigzag antenna (LPZA) has acceptable performance in both gain and polarization. Its height however is large, at about one wavelength (1/spl lambda//sub L/). The concept of fractal antenna is employed in this antenna to achieve the necessary height reduction to /spl lambda//sub L//8, while keeping its radiation characteristics nearly constant. Both single and dual arm quasifractal log-periodic zigzag antenna (QFLPZA) configurations are investigated, with a maximum antenna height of only 1/8th of a wavelength, showing the desired radiation characteristics, and a wide impedance bandwidth of 67%. This type of antenna may find applications in surveillance radar.     

Exact thresholds and optimal codes for the binary-symmetric channel and Gallager's decoding algorithm A

We show that for the case of the binary-symmetric channel and Gallager's decoding algorithm A the threshold can, in many cases, be determined analytically. More precisely, we show that the threshold is always upper-bounded by the minimum of (1-/spl lambda//sub 2//spl rho/'(1))/(/spl lambda/'(1)/spl rho/'(1)-/spl lambda//sub 2//spl rho/'(1)) and the smallest positive real root /spl tau/ of a specific polynomial p(x) and we observe that for most cases this bound is tight, i.e., it determines the threshold exactly. We also present optimal degree distributions for a large range of rates. In the case of rate one-half codes, for example, the threshold x/sub 0//sup */ of the optimal degree distribution is given by x/sup *//sub 0//spl sim/0.0513663. Finally, we outline how thresholds of more complicated decoders might be determined analytically.     

Printed figure-of-eight wire antenna for circular polarization

A new printed wire antenna with circular polarization properties is presented. The geometry of the printed wire which takes the form of a figure-of-eight has a total length of 1.3/spl lambda//sub o/ and serves as a nonresonant traveling-wave antenna. It is shown that a 3-dB axial ratio bandwidth of 15% can be achieved. The half-power and 3-dB axial ratio beamwidth is approximately /spl plusmn/45/spl deg/, while its gain is of the order of 6.5 dB.     

Entropy and the law of small numbers

Two new information-theoretic methods are introduced for establishing Poisson approximation inequalities. First, using only elementary information-theoretic techniques it is shown that, when S/sub n/=/spl Sigma//sub i=1//sup n/X/sub i/ is the sum of the (possibly dependent) binary random variables X/sub 1/,X/sub 2/,...,X/sub n/, with E(X/sub i/)=p/sub i/ and E(S/sub n/)=/spl lambda/, then D(P(S/sub n/)/spl par/Po(/spl lambda/)) /spl les//spl Sigma//sub i=1//sup n/p/sub i//sup 2/+[/spl Sigma//sub i=1//sup n/H(X/sub i/)-H(X/sub 1/,X/sub 2/,...,X/sub n/)] where D(P(S/sub n/)/spl par/Po(/spl lambda/)) is the relative entropy between the distribution of S/sub n/ and the Poisson (/spl lambda/) distribution. The first term in this bound measures the individual smallness of the X/sub i/ and the second term measures their dependence. A general method is outlined for obtaining corresponding bounds when approximating the distribution of a sum of general discrete random variables by an infinitely divisible distribution. Second, in the particular case when the X/sub i/ are independent, the following sharper bound is established: D(P(S/sub n/)/spl par/Po(/spl lambda/))/spl les/1//spl lambda/ /spl Sigma//sub i=1//sup n/ ((p/sub i//sup 3/)/(1-p/sub i/)) and it is also generalized to the case when the X/sub i/ are general integer-valued random variables. Its proof is based on the derivation of a subadditivity property for a new discrete version of the Fisher information, and uses a recent logarithmic Sobolev inequality for the Poisson distribution.     

A minimum cost heterogeneous sensor network with a lifetime constraint

We consider a heterogeneous sensor network in which nodes are to be deployed over a unit area for the purpose of surveillance. An aircraft visits the area periodically and gathers data about the activity in the area from the sensor nodes. There are two types of nodes that are distributed over the area using two-dimensional homogeneous Poisson point processes; type 0 nodes with intensity (average number per unit area) /spl lambda//sub 0/ and battery energy E/sub 0/; and type 1 nodes with intensity /spl lambda//sub 1/ and battery energy E/sub 1/. Type 0 nodes do the sensing while type 1 nodes act as the cluster heads besides doing the sensing. Nodes use multihopping to communicate with their closest cluster heads. We determine them optimum node intensities (/spl lambda//sub 0/, /spl lambda//sub 1/) and node energies (E/sub 0/, E/sub 1/) that guarantee a lifetime of at least T units, while ensuring connectivity and coverage of the surveillance area with a high probability. We minimize the overall cost of the network under these constraints. Lifetime is defined as the number of successful data gathering trips (or cycles) that are possible until connectivity and/or coverage are lost. Conditions for a sharp cutoff are also taken into account, i.e., we ensure that almost all the nodes run out of energy at about the same time so that there is very little energy waste due to residual energy. We compare the results for random deployment with those of a grid deployment in which nodes are placed deterministically along grid points. We observe that in both cases /spl lambda//sub 1/ scales approximately as /spl radic/(/spl lambda//sub 0/). Our results can be directly extended to take into account unreliable nodes.     

A miniaturized net-type microstrip bandpass filter using /spl lambda//8 resonators

A novel miniaturized three-pole net-type bandpass filter using /spl lambda//8 resonators has been proposed. Asymmetric frequency characteristics of this filter exhibit a single transmission zero on the lower side of the passband at finite frequency, which is attributed to multi-path effect. Full-wave simulator IE3D is used to extract the coupling coefficients and external quality factor in order to determine the physical dimensions of this filter. The measured results are in good agreement with the simulated predictions. The overall size of the filter is only about 0.22/spl lambda//sub g/ by 0.2 /spl lambda//sub g/. As a result, the filter has not only a small size but also a wider upper stopband up to 6.5 f/sub 0/.     

Uniplanar compact wideband bandstop filter

A uniplanar wideband bandstop filter is proposed using two bent open-end stubs. The proposed filter consists of the bent connecting line of /spl lambda//sub g//2 between two bent /spl lambda//sub g//4 stubs, which results in wideband design with a rejection bandwidth of 90% at 2.05 GHz. Further, the connecting line and stubs have the same characteristic impedance. The proposed filter compared to the conventional one is also more compact. The area of the novel filter is (/spl lambda//sub g//4)/sup 2/ at the center frequency of the stopband, while the area of the filter realized using the nonbent stubs and connecting line is 2(/spl lambda//sub g//4)/sup 2/ for the same stopband characteristics.     

Compact bandpass filters with wide controllable fractional bandwidth

In this letter, complementary split ring resonators (CSRR) are proposed to design bandpass filters (BPFs) having wide controllable 3-dB fractional bandwidth (FBW). FBW can be varied between 10% and 100%. In addition, filters have the advantages of compactness, sharp rejection, low insertion loss (IL), and low cost. Two prototype fabricated filters of FBW 10.8% and 81.6% show a maximum passband IL of 1.2dB. Filter occupying area is less than 0.25/spl lambda//sub g//spl times/0.15/spl lambda//sub g/, where /spl lambda//sub g/ is the guided wavelength at the midband frequency.     

Design of square-ring microstrip antenna for circular polarisation

The design of a square-ring microstrip antenna with circular polarisation (CP) is presented. To compact the antenna size and overcome the high impedance problem, the CP antenna is excited by a coupling strip located inside the square-ring patch. Several prototypes of the square-ring CP antennas with various substrate thickness (0.013-0.09/spl lambda//sub 0/) have been constructed and studied experimentally, and their coupling-strip designs and CP performance are described.     

High-responsivity high-gain In/sub 0.53/Ga/sub 0.47/As-InP quantum-well infrared photodetectors grown using metal-organic vapor phase epitaxy

We report the growth and fabrication of bound-to-bound In/sub 0.53/Ga/sub 0.47/As-InP quantum-well infrared photodetectors using metal-organic vapor phase epitaxy. These detectors have a peak detection wavelength of 8.5 /spl mu/m. The peak responsivities are extremely large with R/sub pk/=6.9 A/W at bias voltage V/sub b/=3.4 V and temperature T=10 K. These large responsivities arise from large detector gain that was found to be g/sub n/=82 at V/sub b/=3.8 V from dark current noise measurements at T=77 K and g/sub p/=18.4 at V/sub b/=3.4 V from photoresponse data at T=10 K. The background-limited temperature with F/1.2 optics is T/sub BLIP/=65 K for 0相似文献