Short communication: Separation and quantification of caseins and casein macropeptide using ion-exchange chromatography

The aim of this work was to improve an existing method to separate and quantify the 4 major caseins from milk samples (i.e., containing whey proteins) using ion-exchange chromatography. The separation process was carried out using a mini-preparative cation exchange column (1 or 5 mL of column volume), using urea acetate as elution buffer at pH 3.5 with a NaCl gradient. All 4 major caseins were separated, and the purity of each peak was assessed using sodium dodecyl sulfate-PAGE. Purified casein fractions were also added to raw milk to confirm their elution volumes. The quantification was carried out using purified caseins in buffer as well as added directly to fresh skim milk. This method can also be employed to determine the decrease in κ-casein and the release of the casein-macropeptide during enzymatic hydrolysis using rennet. In this case, the main advantage of using this method is the lack of organic solvents compared with the conventional method for separation of macropeptide (using reversed phase HPLC).     

Filtration of milk fat globule membrane fragments from acid buttermilk cheese whey

The proteins and polar lipids present in milk fat globule membrane (MFGM) fragments are gaining attention for their technological and nutritional properties. These MFGM fragments are preferentially enriched in side streams of the dairy industry, like butter serum, buttermilk, and whey. The objective of this study was to recover MFGM fragments from whey by tangential filtration techniques. Acid buttermilk cheese whey was chosen as a source for purification by tangential membrane filtration because it is relatively rich in MFGM-fragments and because casein micelles are absent. Polyethersulfone and cellulose acetate membranes of different pore sizes were evaluated on polar lipid and MFGM-protein retention upon filtration at 40°C. All fractions were analyzed for dry matter, ash, lipids, proteins, reducing sugars, polar lipid content by HPLC, and for the presence of MFGM proteins by sodium dodecyl sulfate-PAGE. A fouling coefficient was calculated. It was found that a thermocalcic aggregation whey pretreatment was very effective in the clarification of the whey, but resulted in low permeate fluxes and high retention of ash and whey proteins. By means of an experimental design, the influence of pH and temperature on the fouling and the retention of polar lipids (and thus MFGM fragments), proteins, and total lipids upon microfiltration with 0.15 μM cellulose acetate membrane was investigated. All models were highly significant, and no outliers were observed. By increasing the pH from 4.6 to 7.5, polar lipid retention at 50°C increased from 64 to 98%, whereas fouling of the filtration membrane was minimized. A 3-step diafiltration of acid whey under these conditions resulted in a polar lipid concentration of 6.79 g/100 g of dry matter. As such, this study shows that tangential filtration techniques are suited for the purification of MFGM fragments.     

Microfiltration of butter serum upon casein micelle destabilization

The gross composition of butter serum, the aqueous phase of butter, is comparable to that of buttermilk, except that it has a higher content of material derived from the milk fat globule membrane (MFGM). As such, butter serum is a good source for further purification of MFGM material. The purified fraction could be of interest for its emulsifying and nutritional properties. The effect of sodium citrate and ethanol on the dissociation of butter serum casein micelles, and their effect on casein retention upon tangential microfiltration were investigated. Optimal conditions of casein micelle dissociation were assessed by using an experimental design (response surface full central composite orthogonal design) with temperature and ethanol or sodium citrate concentration as design variables and the Hunter L* value as response variable. For both dissociating agents, a highly significant reduced quadratic model was fit to the data. Microfiltration tests were performed on pure butter serum, and on butter serum in the presence of sodium citrate, under optimal dissociation conditions (50°C, 80 mM). A cellulose acetate membrane with a pore size of 0.15 μm was used. From the filtration curves and fouling coefficients it was clear that the addition of sodium citrate improved the permeation flux, and minimized fouling. All fractions were analyzed for dry matter, protein, lactose, lipid, and polar lipid contents. The protein fraction was further characterized by sodium dodecyl sulfate-PAGE. It was shown that sodium citrate greatly enhanced casein transmission through the membrane, but at the expense of substantial losses of polar lipids.     

Evidence for fibril-like structure in bovine casein micelles

The addition of Congo red (CR) dye to diluted raw skim milk resulted in a red shift indicative of the presence of fibril-like structures. Thioflavin T (ThT) is another dye that very specifically binds to protein fibrils, and when added to undiluted raw skim milk, the classic 485 nm fluorescence peak of a ThT-fibril complex was observed. Repeating these experiments with various raw milk components showed that the CR red shift and ThT fluorescence peak were due to the presence of casein micelles, and to a lesser extent, sodium caseinate. Fluorescent peaks were also observed when ThT was added to solutions of purified α_S- and κ-casein, but not β-casein, in 0.5 M HEPES buffer (pH = 6.8). The addition of 25 mM Ca²⁺ had no effect on β-casein fluorescence, and significantly reduced the κcasein peak. However, adding 25 mM Ca²⁺ to α_S-casein produced a turbid solution and a 6-fold increase in fluorescence, indicating that the aggregates formed contain fibril-like structure. Casein micelle images obtained by transmission electron microscopy showed the presence of short (7 to 10 nm) fibers cross-linked by dense aggregate junction zones. The observed fibers closely resemble protofibrils, intermediate structures that are observed during the formation of amyloid fibrils.     

How does live yeast differ from sodium bicarbonate to stabilize ruminal pH in high-yielding dairy cows?

The objectives of this study were to evaluate the capacity of 2 dietary feed additives, sodium bicarbonate and live yeast Saccharomyces cerevisiae (strain Sc 47), in optimizing ruminal pH in dairy cows and to determine their modes of action. Three early lactating Holstein cows, fitted with ruminal cannulas, were allocated in a 3 × 3 Latin square design. They were given a total mixed ration as control diet (CD) at a daily feeding rate of 28.0 kg of dry matter (DM)/cow supplemented with 150 g/d of sodium bicarbonate (SBD) or 5 g/d of live yeast (YD) during a 21-d experimental period (14 d of diet adaptation, 4 consecutive days of measurement and sampling and 3 d of transition). The pH and redox potential (E_h) were measured from 1 h before feeding to 8 h after feeding at 1-h intervals, and samples of ruminal fluid were taken at 0, 2, 4, 6, and 8 h after feeding for the determination of volatile fatty acids and lactate concentrations. Total tract apparent digestibility of the diet was also determined. Ruminal pH fluctuated between 6.53 at feeding and 5.57 at 5 h postfeeding. Mean pH was greater with SBD (6.21) and YD (6.14) compared with CD (5.94), showing that both additives had a pH stabilization effect. The E_h varied from -88 mV at 1 h before feeding to -165 mV at 1 h after feeding. Mean E_h and Clark's Exponent (rH) were lower with YD (-149 mV and 7.31, respectively) than with SBD (-137 mV and 7.85, respectively) and CD (-115 mV and 8.05, respectively), indicating that the yeast strengthened the reducing power of the milieu. Total volatile fatty acids were greater in SBD (95.3 mM) and YD (99.4 mM) compared with CD (85.3 mM). Acetate concentration was greater in SBD (60.8 mM) and YD (59.1 mM) compared with CD (53.2 mM). Propionate concentration was greater in YD (25.8 mM) than in SBD (20.0 mM) and CD (18.0 mM). Butyrate remained constant between diets. Mean total lactate concentrations were 16.5, 12.2, and 5.4 mM for CD, SBD, and YD, respectively, with a 67% decrease with YD. Total tract organic matter digestibility was greater for YD (66.6%) compared with SBD (61.7%) and CD (62.2%). The neutral detergent fiber digestibility was greater with YD (41.6%) compared with SBD (34.3%) and CD (29.6%), whereas acid detergent fiber digestibility was greatest in YD (32.3%), intermediate in SBD (24.4%), and lowest in CD (18.1%). By inducing a lower ruminal E_h and rH, live yeast prevented accumulation of lactate and allowed better fiber digestion, whereas sodium bicarbonate seemed to act only as an exogenous buffer.     

Properties of milk protein gels formed by phosphates

We investigated the properties of gels that were formed by adding emulsifying salts, such as tetrasodium pyrophosphate (TSPP), to reconstituted milk protein concentrate solution. The pH of a 51 g/L milk protein concentrate solution was adjusted to 5.8 after adding TSPP. Milk protein concentrate solutions were placed in glass jars and allowed to stand at 25°C for 24 h. Gels with the highest breaking force were formed when TSPP was added at a concentration of 6.7 mM, whereas no gel was formed when TSPP was added at concentrations of ≤2.9 or ≥10.5 mM. Several other phosphate-based emulsifying salts were tested but for these emulsifying salts, gelation only occurred after several days or at greater gelation temperatures. No gelation was observed for trisodium citrate. Gelation induced by TSPP was dependent on pH, and the breaking force of gel was greatest at pH 6.0. Furthermore, when the concentration of milk protein concentrate in solution was increased to 103 g/L, the breaking force of the gel increased, and a clearly defined network between caseins could be observed by using confocal scanning laser microscopy. These results suggest that TSPP-induced gelation occurs when the added TSPP acts with calcium as a cross-linking agent between dispersed caseins and when the balance between (a reduced) electrostatic repulsion and (enhanced) attractive (hydrophobic) interactions becomes suitable for aggregation and eventual gelation of casein molecules.     

Effect of trisodium citrate on rheological and physical properties and microstructure of yogurt

The effect of trisodium citrate (TSC) on the rheological and physical properties and microstructure of yogurt was investigated. Reconstituted skim milk was heated at 85° C for 30 min, and various concentrations (5 to 40 mM) of TSC were added to the milk, which was then readjusted to pH 6.50. Milk was inoculated with 2% yogurt culture and incubated at 42° C until pH was 4.6. Acid-base titration was used to determine changes in the state of colloidal calcium phosphate (CCP) in milk. Total and soluble Ca contents of the milk were determined. The storage modulus (G′) and loss tangent (LT) values of yogurts were measured as a function of pH using dynamic oscillatory rheology. Large deformation rheological properties were also measured. Microstructure of yogurt was observed using confocal scanning laser microscopy, and whey separation was also determined. Addition of TSC reduced casein-bound Ca and increased the solubilization of CCP. The G′ value of gels significantly increased with addition of low levels of TSC, and highest G′ values were observed in samples with 10 to 20 mM TSC; higher ( > 20 mM) TSC concentrations resulted in a large decrease in G′ values. The LT of yogurts increased after gelation to attain a maximum at pH ∼5.1, but no maximum was observed in yogurts made with ≥ 25 mM of TSC because CCP was completely dissolved prior to gelation. Partial removal of CCP resulted in an increase in the LT value at pH 5.1. At low TSC levels, the removal of CCP crosslinks may have facilitated greater rearrangement and molecular mobility of the micelle structure, which may have helped to increase G′ and LT values of gels by increasing the formation of crosslinks between strands. At high TSC concentrations the micelles were completely disrupted and CCP crosslinks were dissolved, both of which resulted in very weak yogurt gels with large pores obvious in confocal micrographs. Gelation pH and yield stress significantly decreased with the use of high TSC levels. Lowest whey separation levels were observed in yogurt made with 20 mM TSC, and whey separation greatly increased at > 25 mM TSC. In conclusion, low concentrations of TSC improved several important yogurt characteristics, whereas the use of levels that disrupted casein micelles resulted in poor gel properties. We also conclude that the LT maximum observed in yogurts made from heated milk is due to the presence of CCP because the modification of the CCP content altered this peak and the removal of CCP eliminates this feature in the LT profiles.     

Composition and Structure of Fat Globule Surface Layers in Recombined Milk

Protein coverage, composition and structure of surface layers of fat globules in recombined milk were determined. Average protein load was ～6 mg/m² fat surface. Both casein and whey proteins were present in the fat globule surface layer, with casein adsorbed in preference to whey proteins and α_s (α_sl+α_s2)-casein adsorbed in preference to β-casein. Transmission electron microscopy showed that the surface layer of fat globule was made up of casein micelles, fragments of casein micelles and a thin layer of protein, possibly whey proteins. Experiments with surface layers that had been dispersed in EDTA showed that the extent of dissociation of caseins followed the order: β-casein > α_s-casein ≦ K-casein, suggesting that most of the K-casein was probably associated directly with the fat surface.     

Changes in chemical composition of Alxa bactrian camel milk during lactation

Changes in chemical composition of Alxa bactrian camels reared in Inner Mongolia (China) during lactation were investigated. Colostrum and milk samples from 10 nomadic female camels in their first season of lactation were collected periodically from parturition until 90 d postpartum (PP). The average contents of gross composition were 14.23% protein, 4.44% lactose, 0.27% fat, 0.77% ash, and 20.16% total solids in colostrum at 2 h PP, and the respective mean values were 3.55, 4.24, 5.65, 0.87, and 14.31% for regular milk on d 90. A 15-fold increase was shown in fat content during the first 24 h, whereas a sharp decrease was shown during the first 12 h of lactation in protein, ash, and total solids contents. Variation in lactose content was small (4.24 to 4.71%) throughout the study period. Total N, nonprotein N, casein N, and whey protein N were found to be 2.23, 0.06, 0.86, and 1.31 g/100 mL for the colostrum at 2 h PP; and 0.56, 0.04, 0.45, and 0.07 g/100 mL for the milk at 90 d PP. Percentages of caseins increased steadily, whereas whey proteins declined gradually until 3 mo of lactation. Gas liquid chromatography analysis of milk fat showed that the content of even-numbered saturated fatty acids (C_12:0-C_18:0) in camel colostrum (2 h to 7 d PP) was lower than that of regular milk (15 to 90 d PP). The predominant saturated fatty acids were C_14:0, C_16:0, and C_18:0, regardless of the stage of lactation. There was a considerable level of polyunsaturated fatty acids (mainly C_18:1) in Alxa camel's milk fat. The levels of Ca, P, Na, K, and Cl were 222.58, 153.74, 65.0, 136.5, and 141.1 mg/100 g, respectively, at 2 h PP; the values of the minerals were 154.57, 116.82, 72.0, 191.0, and 152.0 mg/100 g, respectively, for the regular milk on d 90. The levels of vitamins A, C, E, B₁, B₂, B₆, and D were 0.97, 29.60, 1.45, 0.12, 1.24, 0.54 mg/L, and 640 IU/L, respectively, in Alxa camel milk at 90 d PP. Vitamin A and C contents were higher and vitamins E and B₁ were lower than those in colostrum. Sodium dodecyl sulfate-PAGE and densitometry results demonstrated that Alxa camel colostrum is rich in immunoglobulins, serum albumin, and 2 unknown fractions, which are reduced in amount (%) within 2 d of lactation. It seems that there is lack of β-lactoglobulin in Alxa camel milk, whereas casein and α-lactalbumin start at a low level and increase gradually until they reach their regular levels in the milk.     

Interfacial composition and stability of emulsions made with mixtures of commercial sodium caseinate and whey protein concentrate

The interfacial composition and the stability of oil-in-water emulsion droplets (30% soya oil, pH 7.0) made with mixtures of sodium caseinate and whey protein concentrate (WPC) (1:1 by protein weight) at various total protein concentrations were examined. The average volume-surface diameter (d₃₂) and the total surface protein concentration of emulsion droplets were similar to those of emulsions made with both sodium caseinate alone and WPC alone. Whey proteins were adsorbed in preference to caseins at low protein concentrations (<3%), whereas caseins were adsorbed in preference to whey proteins at high protein concentrations. The creaming stability of the emulsions decreased markedly as the total protein concentration of the system was increased above 2% (sodium caseinate >1%). This was attributed to depletion flocculation caused by the sodium caseinate in these emulsions. Whey proteins did not retard this instability in the emulsions made with mixtures of sodium caseinate and WPC.     

Pineapple fruit bromelain affinity to different protein substrates

Optimal pH and temperature conditions for proteolytic activity of pineapple fruit bromelain were determined using five different substrates: azocasein and azoalbumin (pH 3–10 at 20–70 °C), casein and sodium caseinate (pH 2–10 at 20–70 °C), and haemoglobin (pH 2–6.5 at 30–60 °C). Fruit bromelain has shown optimum activity at pH 7.5 for azoalbumin and at 6.5 for azocasein, all at 55 °C. Fruit bromelain activity determined with casein and sodium caseinate has shown optimum activity at 59 °C, while the optimum pH was 7.7 for casein and 6.5 for sodium caseinate. Optimum hydrolysis conditions of fruit bromelain towards haemoglobin showed a sharp peak at an acidic pH 2.9 at 37 °C. The lowest results of K_m and the highest results of V_max/K_m were found for azocasein and azoalbumin. These substrates are highly recommended for fruit bromelain activity determination.     

Effect of selected Hofmeister salts on textural and rheological properties of nonfat cheese

Three Hofmeister salts (HS; sodium sulfate, sodium thiocyanate, and sodium chloride) were evaluated for their effect on the textural and rheological properties of nonfat cheese. Nonfat cheese, made by direct acidification, were sliced into discs (diameter = 50 mm, thickness = 2 mm) and incubated with agitation (6 h at 22°C) in 50 mL of a synthetic Cheddar cheese aqueous phase buffer (pH 5.4). The 3 HS were added at 5 concentrations (0.1, 0.25, 0.5, 0.75, and 1.0 M) to the buffer. Post-incubation, cheese slices were air dried and equilibrated in air-tight bags for 18 h at 5°C before analysis. Small amplitude oscillatory rheology properties, including the dynamic moduli and loss tangent, were measured during heating from 5 to 85°C. Hardness was determined by texture profile analysis. Acid-base buffering was performed to observe changes in the indigenous insoluble (colloidal) calcium phosphate (CCP). Moisture content decreased with increasing HS concentration. Cheeses incubated in high concentrations of SCN⁻ softened earlier (i.e., loss tangent = 1) compared with other HS treatments. Higher melting temperature values were observed for cheeses incubated in high concentrations of SO₄²⁻. Hardness decreased in cheeses incubated in buffers with high concentrations of SCN⁻. The indigenous CCP profile of nonfat cheese was not greatly affected by incubation in Cl⁻ or SCN⁻, whereas buffers with high concentrations of SO₄²⁻ reduced the acid-base buffering contributed by CCP. The use of high concentrations (1.0 M) of SCN⁻ for incubation of cheeses resulted in a softer protein matrix at high temperatures due to the chaotropic effect of SCN⁻, which weakened hydrophobic interactions between CN. Cheese samples incubated in 1.0 M SO₄²⁻ buffers exhibited a stiffer protein matrix at high temperatures due to the kosmotropic effect of SO₄²⁻, which helped to strengthen hydrophobic interactions in the proteins during the heating step. This study showed that HS influenced the texture and rheology of nonfat cheese probably by altering the strength of hydrophobic interactions between CN.     

Effect of pH at heat treatment on the hydrolysis of κ-casein and the gelation of skim milk by chymosin

Skim milk was adjusted to pH values between 6.5 and 7.1 and heated at 90 °C for times from 0 to 30 min. After heat treatment, the samples were re-adjusted to the natural pH (pH 6.67) and allowed to re-equilibrate. High levels of denatured whey proteins associated with the casein micelles during heating at pH 6.5 (about 70-80% of the total after 30 min of heating). This level decreased as the pH at heating was increased, so that about 30%, 20% and 10% of the denatured whey protein was associated with the casein micelles after 30 min of heating at pH 6.7, 6.9 and 7.1, respectively. Increasing levels of κ-casein were transferred to the serum as the pH at heating was increased. The loss of κ-casein and the formation of para-κ-casein with time as a consequence of the chymosin treatment of the milk samples were monitored by sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE). The loss of κ-casein and the formation of para-κ-casein were similar for the unheated and heated samples, regardless of the pH at heating or the heat treatment applied. Monitoring the gelation properties with time for the chymosin-treated milk samples indicated that the heat treatment of the milk markedly increased the gelation time and decreased the firmness (G^′) of the gels formed, regardless of whether the denatured whey proteins were associated with the casein micelles or in the milk serum. There was no effect of pH at heat treatment. These results suggest that the heat treatment of milk has only a small effect on the primary stage of the chymosin reaction (enzymatic phase). However, heat treatment has a marked effect on the secondary stage of this reaction (aggregation phase), and the effect is similar regardless of whether the denatured whey proteins are associated with the casein micelles or in the milk serum as nonsedimentable aggregates.     

Binding of vitamin A with milk α- and β-caseins

The binding sites of retinol and retinoic acid with milk α- and β-caseins were determined, using constant protein concentration and various retinoid contents. FTIR, UV–visible and fluorescence spectroscopic methods as well as molecular modelling were used to analyse retinol and retinoic acid binding sites, the binding constant and the effect of retinoid complexation on the stability and conformation of caseins. Structural analysis showed that retinoids bind caseins via both hydrophilic and hydrophobic contacts with overall binding constants of K_{retinol-α-caseins} = 1.21 (±0.4) × 10⁵ M⁻¹ and K_{retinol-β-caseins} = 1.11 (±0.5) × 10⁵ M⁻¹ and K_{retinoic acid-α-caseins} = 6.2 (±0.6) × 10⁴ M⁻¹ and K_{retinoic acid-β-caseins} = 6.3 (±0.6) × 10⁴ M⁻¹. The number of bound retinol molecules per protein (n) was 1.5 (±0.1) for α-casein and 1.0 (±0.1) for β-casein, while 1 molecule of retinoic acid was bound in the α- and β-casein complexes. Molecular modelling showed different binding sites for retinol and retinoic acid on α- and β-caseins with more stable complexes formed with α-casein. Retinoid–casein complexation induced minor alterations of protein conformation. Caseins might act as carriers for transportation of retinoids to target molecules.     

Size of native and heated casein micelles,content of protein and minerals in milk from Norwegian Red Cattle—effect of milk protein polymorphism and different feeding regimes

Milk samples of 59 cows of the Norwegian Red Cattle breed receiving three different supplementary concentrates, were analysed for genotypes of caseins and whey proteins, the content of different milk salts (Ca²⁺, Ca, Mg and citrate), the content of total protein, casein and whey protein and the mean micellar size of native and heated casein micelles. The genotype of α_s1-casein had a statistically significant effect on the content of protein and casein, and the content of whey protein and the casein number were significantly influenced by different feeding regimes, and the content of citrate. The mean size of native and heated casein micelles was significantly influenced by the feeding regimes, genotype of α_s1-casein (native mean size only) and κ-casein, pH and the content of casein, whey protein and casein number. The heat-induced changes in mean micellar size were significantly affected by the calcium ion activity which accounted for approximately 40% of the total variation.     

Transglutaminase cross-linking kinetics of sodium caseinate is changed after emulsification

Enzymatic cross-linking is an important method of modifying the structure of food products to control their texture and stability. In this paper we look at the effect that adsorption to the oil–water interface of triglyceride oil-in-water emulsion has on rates of cross-linking of sodium caseinate by microbial transglutaminase. The kinetics of cross-linking has also been assessed for the individual casein proteins within the caseinate. In solution the rates were α_s2-casein > β-casein > α_s1-casein > κ-casein. This order is not as expected given the rheomorphic nature of the proteins and the number of glutamine and lysine residues in each protein. In particular, the α_s1-casein was cross-linked much more slowly than expected. When sodium caseinate was adsorbed to an emulsion the rates for all constituent caseins were decreased but the cross-linking rate for α_s1-casein was markedly reduced, indicating the most significant change in accessibility following adsorption. This knowledge will facilitate optimal production of cross-linked emulsions for use in future studies aimed at engineering emulsions with improved nutritional quality.     

Effect of calcium on the physical properties of stirred probiotic yogurt

The effect of calcium on the viscosity, firmness, and smoothness, as determined by extent of nodulation, of stirred probiotic yogurt produced by bacterial fermentation was investigated. Standardized milk for yogurt manufacture was prepared, and calcium was added or removed from the system. Calcium was added as Ca²⁺ in the form of CaCl₂ (up to 13.6 mM) or nonionic calcium as Gadocal-K (calcium potassium citrate; up to 49.8 mM). Calcium was removed by chelating with sodium citrate (up to 16 mM) or by cation exchange with Amberlite IR-120 plus (sodium form) resin (up to 10 g/L). Calcium chloride and sodium citrate were added either before or after heat treatment of milk, and nonionic calcium was added before heat treatment. Calcium removal by ion exchange was performed before heat treatment. Neither Ca²⁺ addition nor removal by chelation with citrate resulted in stirred yogurt with viscosity, firmness, and smoothness superior to those of the control yogurt, whereas addition of 49.8 mM nonionic calcium and removal of calcium (5.6 mM or ∼10% of total calcium) by cation exchange improved the firmness and viscosity without affecting yogurt smoothness. The study identified Gadocal-K as a possible source of calcium fortification of stirred yogurt without loss of texture.     

Chemical characterisation and determination of sensory attributes of hydrolysates produced by enzymatic hydrolysis of whey proteins following a novel integrative process

The overall aim of this work was to characterise the major angiotensin-converting enzyme (ACE) inhibitory peptides produced by enzymatic hydrolysis of whey proteins, through the application of a novel integrative process. This process consisted of the combination of adsorption and microfiltration within a stirred cell unit for the selective immobilisation of β-lactoglobulin and casein-derived peptides (CDP) from whey. The adsorbed proteins were hydrolysed in situ, which resulted in the separation of peptide products from the substrate and fractionation of peptides. Two different hydrolysates were produced: (i) from CDP (IC₅₀ = 287 μg/mL) and (ii) from β-lactoglobulin (IC₅₀ = 128 μg/mL). The well-known antihypertensive peptide IPP and several novel peptides that have structural similarities with reported ACE inhibitory peptides were identified and characterised in both hydrolysates. Furthermore, the hydrolysates were assessed for bitterness. No significant difference was found between the bitterness of the control (milk with no hydrolysate) and hydrolysate samples at different concentrations (at, below and above the IC₅₀).     

Isolation and characterisation of κ-casein/whey protein particles from heated milk protein concentrate and role of κ-casein in whey protein aggregation

Milk protein concentrate (79% protein) reconstituted at 13.5% (w/v) protein was heated (90 °C, 25 min, pH 7.2) with or without added calcium chloride. After fractionation of the casein and whey protein aggregates by fast protein liquid chromatography, the heat stability (90 °C, up to 1 h) of the fractions (0.25%, w/v, protein) was assessed. The heat-induced aggregates were composed of whey protein and casein, in whey protein:casein ratios ranging from 1:0.5 to 1:9. The heat stability was positively correlated with the casein concentration in the samples. The samples containing the highest proportion of caseins were the most heat-stable, and close to 100% (w/w) of the aggregates were recovered post-heat treatment in the supernatant of such samples (centrifugation for 30 min at 10,000 × g). κ-Casein appeared to act as a chaperone controlling the aggregation of whey proteins, and this effect was stronger in the presence of α_S- and β-casein.     

Characterisation of binding of iron to sodium caseinate and whey protein isolate

The fortification of dairy products with iron is an important approach to delivering iron in required quantities to the consumer. The binding of iron (ferrous sulfate) to two commercial milk protein products, sodium caseinate and whey protein isolate (WPI), dissolved in 50 mM HEPES buffer, was examined as a function of pH and iron concentration. Sodium caseinate had more sites (n = 14) than WPI (n = 8) for binding iron, and the affinity of caseinate to bind iron was also higher than that of WPI. These differences were attributed to the presence of clusters of phosphoserine residues in casein molecules, which are known to bind divalent cations strongly. The amount of iron bound to sodium caseinate was found to be independent of pH in the range 5.5–7.0, whereas acidification (pH range 7.0–3.0) caused a marked decrease in the amount of iron bound to WPI.