Compatibilization effects of styrenic/rubber block copolymers in polypropylene/polystyrene blends

Compatibilizing effects of styrene/rubber block copolymers poly(styrene‐b‐butadiene‐b‐styrene) (SBS), poly(styrene‐b‐ethylene‐co‐propylene) (SEP), and two types of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS), which differ in their molecular weights on morphology and selected mechanical properties of immiscible polypropylene/polystyrene (PP/PS) 70/30 blend were investigated. Three different concentrations of styrene/rubber block copolymers were used (2.5, 5, and 10 wt %). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the phase morphology of blends. The SEM analysis revealed that the size of the dispersed particles decreases as the content of the compatibilizer increases. Reduction of the dispersed particles sizes of blends compatibilized with SEP, SBS, and low‐molecular weight SEBS agrees well with the theoretical predictions based on interaction energy densities determined by the binary interaction model of Paul and Barlow. The SEM analysis confirmed improved interfacial adhesion between matrix and dispersed phase. The TEM micrographs showed that SBS, SEP, and low‐molecular weight SEBS enveloped and joined pure PS particles into complex dispersed aggregates. Bimodal particle size distribution was observed in the case of SEP and low‐molecular weight SEBS addition. Notched impact strength (a_k), elongation at yield (ε_y), and Young's modulus (E) were measured as a function of weight percent of different types of styrene/rubber block copolymers. The a_k and ε_y were improved whereas E gradually decreased with increasing amount of the compatibilizer. The a_k was improved significantly by the addition of SEP. It was found that the compatibilizing efficiency of block copolymer used is strongly dependent on the chemical structure of rubber block, molecular weight of block copolymer molecule, and its concentration. The SEP diblock copolymer proved to be a superior compatibilizer over SBS and SEBS triblock copolymers. Low‐molecular weight SEBS appeared to be a more efficient compatibilizer in PP/PS blend than high‐molecular weight SEBS. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 291–307, 1999     

Influence of the incorporation of fine calcium carbonate particles on the impact strength of polypropylene/polystyrene‐block‐poly(ethylene butene)‐block‐polystyrene blends

The Izod impact strength of two kinds of ternary composites was investigated. One consisted of polypropylene (PP), the triblock copolymer polystyrene‐block‐poly(ethylene butene)‐block‐polystyrene (SEBS), and calcium carbonate (CaCO₃) particles, and the other consisted of PP, carboxylated SEBS (C‐SEBS), and CaCO₃ particles. The mean size of the CaCO₃ particles was about 160 nm. According to scanning electron microscopy observations, the composite with SEBS showed a morphology in which SEBS domains and CaCO₃ particles were independently dispersed in the PP matrix. On the other hand, the composite with C‐SEBS showed a morphology in which CaCO₃ particles were encapsulated by C‐SEBS; that is, a core–shell structure was formed. The Izod impact strength of the composite with SEBS was higher than that of the composite with C‐SEBS and the PP/SEBS and PP/C‐SEBS binary blends. According to observations of the fractured surface, the stress‐whitened area was larger in the composite with SEBS than in the composite with C‐SEBS and the PP/SEBS and PP/C‐SEBS binary blends. The toughening mechanism of the composite, using nanometer‐sized CaCO₃ particles in combination with SEBS, was examined. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

A strategy for the preparation of closed‐cell and crosslinked polypropylene foam by supercritical CO2 foaming

We report the preparation of a closed‐cell polypropylene (PP) foam material by supercritical carbon dioxide foaming with the assistance of γ‐ray radiation crosslinking. Styrene–ethylene–butadiene–styrene (SEBS) copolymer was added to PP to enhance radiation crosslinking and nucleation. Radiation effects on the foaming of the PP/SEBS blend with different ratios were investigated. A significant improvement in the foaming of the crosslinked PP/SEBS blend was achieved as compared to pristine PP. The cell density of the crosslinked PP/SEBS foam greatly increased at a dose of 10 kGy and a high closed‐cell ratio was obtained. The tensile strength of the crosslinked PP/SEBS foams (10 kGy) was improved from 14 to 20.7 MPa compared to pristine PP foam (0 kGy). In addition, the crosslinked PP/SEBS blend exhibited a wider foaming temperature window (10 °C) as compared to the non‐crosslinked ones (4 °C). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45809.     

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐ b‐styrene] on dielectric,thermal, and morphological characteristics of polypropylene/silica nanocomposites

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) copolymer on the thermal and dielectric properties of polypropylene (PP)—nanosilica (NS) composites in relation with morphological aspects revealed by atomic force microscopy (AFM) was investigated in this article. SEBS hindered the crystallization process of PP in PP/NS composites, leading to a smaller degree of crystallinity and lower perfection of crystalline structure. Broader lamellar thickness distribution was obtained in nanocomposites containing SEBS. Almost two times higher dielectric loss as compared to PP reference and two relaxation processes were detected in ε_r ^′′(f) curves of nanocomposites. The first peak, in the same frequency domain as for the references, was assigned to α‐relaxation of polymer components together with interfacial polarization. The relaxation time follows the Arrhenius law with an activation energy of 80–90 kJ/mol. For the second process, the temperature dependence of the relaxation times obeyed the VFT equation. The dielectric changes following the incorporation of SEBS support its tendency to hinder the motional processes in PP, in accordance with DSC results. A smooth transition from a phase rich in SEBS to one containing mainly PP was detected in the AFM image of the composite with the larger amount of SEBS, emphasizing the good compatibility at the PP/SEBS interface. POLYM. ENG. SCI., 53:2081–2092, 2013. © 2013 Society of Plastics Engineers     

Dynamically vulcanized blends of polypropylene and ethylene‐octene copolymer: Comparison of different peroxides on mechanical,thermal, and morphological characteristics

Thermoplastic vulcanizates (TPVs) are prepared by the dynamic vulcanization process, where crosslinking of an elastomer takes place during its melt mixing with a thermoplastic polymer under high shear. TPVs based on polypropylene (PP) with different grades of ethylene‐octene copolymers (EOC) were prepared with a coagent assisted peroxide crosslinking system. The effect of dynamic vulcanization and influence of various types and concentrations of peroxide were mainly studied on the basis of the mechanical, thermal, and morphological characteristics. Three structurally different peroxides, namely dicumyl peroxide (DCP), tert‐butyl cumyl peroxide (TBCP), and di‐tert‐butyl peroxy isopropyl benzene (DTBPIB) were investigated. The mechanical properties of the TPVs are primarily determined by the extent of crosslinking in the EOC and the degree of degradation in the PP phase. Among all peroxides used DCP gives best overall properties with low‐molecular‐weight EOC, whereas TBCP shows best property level with high‐molecular‐weight EOC‐based TPVs. These can be explained on the basis of the molecular characteristics of EOC and the nature of the peroxide used. Differential scanning calorimetery (DSC) and morphological analysis reveal that PP and EOC are a thermodynamically immiscible system. The melting endotherm was studied to determine the influence of various peroxides on crystallinity of the PP phase. Tensile fracture patterns were also analyzed to study the failure mechanism of the samples. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Drop weight impact and work of fracture of short glass fiber reinforced polypropylene composites toughened with elastomer

Short glass fiber (SGF) reinforced polypropylene composites toughened with styrene‐ethylene butylene‐styrene (SEBS) or maleated SEBS (SEBS‐g‐MA) triblock copolymer were injection molded. Charpy drop‐weight impact properties and the impact essential work of fracture (EWF) of the SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrids were investigated. Drop‐weight impact results revealed that the SGF/SEBS/PP hybrid exhibits higher impact strength than the SGF/SEBS‐g‐MA/PP hybrid at low impact speeds. This was derived from the pull‐out of fibers from the SGF/SEBS/PP hybrid. At high impact speeds, the impact strength of the SGF/SEBS‐g‐MA/PP hybrid was slightly higher than that of the SGF/SEBS/PP hybrid. Impact EWF measurements showed that the hybrids only exhibit specific essential work (W_e) at a high impact speed of 3 ms⁻¹. The non‐essential work does not occur in the hybrids under high impact rate loading conditions. Moreover, SEBS or SEBS‐g‐MA addition was beneficial in enhancing the high‐rate specific essential work of the SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites.     

Distribution of oil in olefinic thermoplastic elastomer blends

The distribution of processing oil in two olefinic thermoplastic elastomer (OTPE) blends was determined using dielectric spectroscopy. The OPTE blends are blends of dynamically vulcanised EPDM with polypropylene (PP), TPVs, and blends of PP with SEBS. Both blend types contain paraffinic oil, which is present in both the PP and in the elastomer phase. The determination of the actual oil concentration by measuring the reduction in the glass transition temperatures (T_g) is inaccurate using DSC or DMA, because the glass transition dynamics of the two phases overlap. The blends were made sensible for dielectric spectroscopy by the addition of a probe molecule. The oil distribution was determined by modelling of the dielectric loss of the OPTE blends in the T_g regime from the ones of the binary mixtures. The mean value for the oil distribution coefficient was found to be 0.6 for PP/SEBS blends and 0.63 for TPVs.     

Multifunctional peroxide as alternative crosslink agents for dynamically vulcanized epoxidized natural rubber/polypropylene blends

Commonly used dicumyl peroxide (DCP) in combination with coagent, triallyl cyanurate (TAC), as a crosslinking agent is well acceptable for dynamically vulcanized rubber phase of thermoplastic vulcanizates (TPVs). However, it generally produces volatile decomposition products, which cause a typical unpleasant smell and a blooming phenomenon. In this work, influence of two types of multifunctional peroxides: 2,4‐diallyloxy‐6‐tert‐butylperoxy‐1,3,5‐triazine (DTBT) and 1‐(2‐tert‐butylperoxyisopropyl)‐3‐isopropenyl benzene (TBIB), on properties of TPVs based on epoxidized natural rubber (ENR)/polypropylene (PP) blends were investigated. The conventional peroxide/coagent combinations, i.e., DCP/TAC and tert‐butyl cumyl peroxide (TBCP)/α‐methyl styrene (α‐MeS) were also used to prepare the TPVs for a comparison purpose. The TPVs with multifunctional peroxide, DTBT, provided good mechanical properties and phase morphology of small dispersed vulcanized rubber domains in the PP matrix which were comparable with the DCP/TAC cured TPVs. However, the TPVs with TBIB/α‐MeS and TBCP/α‐MeS showed comparatively low values of the tensile properties as well as rather large phase morphology. The results were interpreted by three main factors: the kinetic aspects of the various peroxides, solubility parameters of respective peroxide/coagent combinations in the ENR and PP phases, and the tendency to form unpleasantly smelling byproducts. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

SBS and SEBS block copolymers as impact modifiers for polypropylene compounds

Blends of polypropylene (PP) and thermoplastic elastomers (TPE), namely SBS (styrene‐butadiene‐styrene) and SEBS (styrene‐ethylene/1‐butene‐styrene) block copolymers, were prepared to evaluate the effectiveness of the TPE type as an impact modifier for PP and influence of the concentration of elastomer on the polymer properties. Polypropylene homopolymer (PP‐H) and ethylene–propylene random copolymer (PP‐R) were evaluated as the PP matrix. Results showed that TPEs had a nucleating effect that caused the PP crystallization temperature to increase, with SBS being more effective than SEBS. Microstructure characterization tests showed that in most cases PP/SEBS blends showed the smallest rubber droplets regardless of the matrix used. It was seen that SEBS is a more effective toughening agent for PP than SBS. At 0°C the Izod impact strength of the PP‐H/SEBS 30% b/w blend was twofold higher than the SBS strength, with the PP‐R/SEBS 30% b/w blend showing no break. A similar behavior on tensile properties and flexural modulus were observed in both PP/TPE blends. Yield stress and tensile strength decreased and elongation at break increased by expanding the dispersed elastomeric phase in the PP matrix. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 254–263, 2005     

Rheological behaviors of glass bead‐ and wollastonite‐filled polypropylene composites modified with thermoplastic elastomers

Steady‐ and oscillatory‐shear rheological behaviors of polypropylene/glass bead (PP/GB) and PP/wollastonite (PP/W) melts modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were examined by means of a parallel‐plate rheometer. With adding the elastomers (SEBS and SEBS‐g‐MA) and fillers (spherical GB and acicular W) to PP, viscosity especially at low shear rates and shear‐thinning flow behavior at high shear rates were pronounced as evidenced quantitatively by Carreau–Yasuda (CY) parameters, but Cox–Merz analogy became weakened. Besides, melt‐elasticity in terminal region and relaxation time (t_c) in crossing point increased, indicating an enhancement in quasi‐solid behavior of molten PP. Comparing with the elastomers, rheological behaviors of molten PP were more influenced with adding the rigid fillers, especially with W due to distinct acicular shape of W particles. SEBS‐g‐MA elastomer more affected rheological behaviors of the ternary composites than SEBS elastomer, implying that SEBS elastomer and the filler particles behaved individually (i.e., development of separate microstructure) in (PP/GB)/SEBS and (PP/W)/SEBS ternary composites, but core‐shell microstructure developed with strong interfacial adhesion by adding SEBS‐g‐MA elastomer, and the filler particles encapsulated with the thick SEBS‐g‐MA elastomer interlayer (i.e., core‐shell particles) acted like neither big elastomer particles nor like individual rigid particles in melt‐state. Moreover, effects of SEBS‐g‐MA elastomer reached a maximum on rheological behaviors of (PP/W)/SEBS‐g‐MA ternary composite, indicating a synergy between core‐shell microstructure and acicular W particles. Correlations between oscillatory‐shear flow properties and microstructures of the blends and composites were evaluated using Cole–Cole (CC), Han–Chuang (HC), and van Gurp–Palmen (vGP) plots. COMPOS., 2012. © 2012 Society of Plastics     

Evaluation of mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends using Taguchi experimental analysis

In this work, ternary polymer blends based on polypropylene (PP)/polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) (SEBS) triblock copolymer and a reactive maleic anhydride grafted SEBS (SEBS‐g‐MAH) at fixed compositions are prepared using twin‐screw extruder at different levels of die temperature (235‐245‐255°C), screw speed (70‐100‐130 rpm), and blending sequence (M1‐M2‐M3). In M₁ procedure, all of the components are dry blended and extruded simultaneously using Brabender twin‐screw extruder, whereas in M₂ procedure, PC, SEBS, and SEBS‐g‐MAH minor phases are first preblended in twin‐screw extruder and after granulating are added to PP continuous phase in twin‐screw extruder. Consequently, in M₃ procedure, PP and SEBS‐g‐MAH are first preblended and then are extruded with other components. The influence of these parameters as processing conditions on mechanical properties of PP/PC/SEBS ternary blends is investigated using L9 Taguchi experimental design. The responding variables are impact strength and tensile properties (Young's modulus and yield stress), which are influenced by the morphology of ternary blend, and the results are used to perform the analysis of mean effect as well. It is shown that the resulted morphology, tensile properties, and impact strength are influenced by extrusion variables. Additionally, the optimum processing conditions of ternary PP/PC/SEBS blends were achieved via Taguchi analysis. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of the compatibilizer,on the engineering properties of TPV based on Hypalon® and PP prepared by dynamic vulcanization

Elastomeric Chlorosulfonated polyethylene (Hypalon^®) and thermoplastic Polypropylene (PP) based thermoplastic vulcanizates (TPVs) were prepared in presence of different doses of compatibilizer, maleic anhydride grafted PP (PP‐g‐MA) by employing dynamic vulcanization technique. The effect of incorporation in different proportions of compatibilizer on mechanical, spectral, morphological, thermal, and rheological properties of such TPVs was studied and the same were compared to that of virgin PP and amongst themselves. The mechanical analysis of the prepared TPVs exhibited significant improvements in stress at 25% modulus, ultimate tensile strength (UTS), and hardness values. FTIR studies revealed that a chemical interaction had taken place between Hypalon^® and functionalized compatibilizer during the process of dynamic vulcanization which led to an enhancement of interfacial adhesion between them. The two‐phase morphologies were clearly observed by scanning electron microscopic studies. The T_g values of Hypalon^® was modified in the TPVs as exhibited by differential scanning calorimetric studies. TGA studies indicated the increase in thermal stability of all TPVs with respect to the elastomeric Hypalon^®. Rheological properties showed that the compatibilizer reduces the melt viscosity of TPVs and thus facilitates the processibility of such TPVs. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40312.     

Tensile deformation mechanisms of polypropylene/elastomer blends reinforced with short glass fiber

Polypropylene hybrid composites reinforced with short glass fiber (SGF) and toughened with styrene–ethylene butylenes–styrene (SEBS) elastomer were prepared using extrusion and injection‐molding techniques. Moreover, hybrids compatibilized with SEBS‐grafted maleic anhydride (SEBS‐g‐MA) and hybrid compatibilized with PP grafted with maleic anhydride (PP‐g‐MA) were also fabricated. The matrix of the latter hybrid was designated as mPP and consisted of 95% PP and 5% PP‐g‐MA. Tensile dilatometry was carried out to characterize the fracture mechanisms of hybrid composites. Dilatometric responses showed that the elastic deformation was the dominant deformation mechanism for the SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrids. However, cavitation deformation prevailed over shearing deformation for both hybrids at the higher strain regime. The cavitation strain resulted from the debonding of glass fibers and from the crazing of the matrix in the SGF/SEBS/PP hybrid. In contrast, the cavitation was caused by the debonding of SEBS particles from the matrix of the SGF/SEBS‐g‐MA/PP hybrid. The use of PP‐g‐MA resulting in elastic deformation was the main mode of deformation in the low‐strain region for the SGF/SEBS/mPP and SEBS/SEBS‐g‐MA/mPP hybrids; thereafter, shearing appeared to dominate at the higher strain regime. This was attributed to the MA functional group improving the bonding between the SGF and PP. The correlation between fracture morphology and dilatometric responses also is presented in the article. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 441–451, 2003     

Peroxide crosslinking of unplasticized poly(vinyl chloride)

A crosslinking system consisting of 1,1‐di‐t‐butylperoxy‐3,3,5‐trimethyl cyclohexane peroxide and trimethylolpropane trimethacrylate (TMPTMA) has been used to introduce crosslinks into unplasticized poly(vinyl chloride) (PVC). The influence of the concentration of both reagents has been investigated, and crosslinking monitored by determination of the remaining sample weight after Soxhlet extraction with tetrahydrofuran. The system used (i.e., 0.5–2.0 phr peroxide with 5 to 15 phr TMPTMA) has been shown to be effective for crosslinking PVC. Gel contents of 30–40% have been obtained, premature crosslinking during processing is largely avoided, but thermal stability still needs to be improved. Considerable improvements in elevated temperature mechanical properties can be attained using an appropriate TMPTMA/peroxide concentration. The best tensile properties were obtained with 0.5 phr peroxide and 15 phr TMPTMA. Observed increases in T_g, also achievable with only 0.5 phr peroxide, but only slightly dependent on TMPTMA concentration, represent a useful increase in service temperature for the resulting compound. Lower peroxide levels may be adequate to achieve property improvements. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2657–2666, 2000     

Influence of Elastomer Modification on Impact Strength of PP/Elastomer/CaCO3 Composite

Polypropylene (PP)/elastomer/fine filler particle ternary composite was prepared using polystyrene-block-poly(ethylene-butene)-block-polystyrene triblock copolymer (SEBS) or carboxylated SEBS (C-SEBS) as elastomer and calcium carbonate (CaCO₃) having mean size about 160 nm as filler. First, SEBS (or C-SEBS) and CaCO₃ particles were mixed to form master batch. Second, the prepared master batch and PP matrix were kneaded. In the PP/SEBS/CaCO₃ ternary composite, CaCO₃ particles and SEBS particles were dispersed in the PP matrix separately. In the PP/C-SEBS/CaCO₃ ternary composite, CaCO₃ particles were encapsulated in C-SEBS and formed a core–shell structure at lower CaCO₃ concentration; however, some CaCO₃ particles were dispersed in PP matrix at higher CaCO₃ concentration. In the PP/SEBS/CaCO₃ composite, the impact strength increased with the amount of incorporated CaCO₃ particles. Whereas, in the PP/C-SEBS/CaCO₃ composite, the impact strength increased with the amount of CaCO₃ particles dispersed in PP matrix. The master-batch method was found to be useful for improving the dispersibility of CaCO₃ particles than the commonly used single-batch method.     

Dynamically vulcanized blends of polypropylene and ethylene octene copolymer: Influence of various coagents on mechanical and morphological characteristics

Dynamically cured blends of polypropylene (PP) and ethylene octene copolymer (EOC) with coagent‐assisted peroxide curative system were prepared by melt‐mixing method. It was well established that PP exhibits β‐chain scission in the presence of peroxide. Principally, incorporation of a coagent increases the crosslinking efficiency in the EOC phase and decreases the extent of degradation in the PP phase. The present study mainly focused on the influence of three structurally different coagents, namely, triallyl cyanurate (TAC), trimethylol propane triacrylate (TMPTA), and N,N′‐m‐phenylene dimaleimide (MPDM), on the mechanical properties of the PP/EOC thermoplastic vulcanizates (TPVs). The reactivity and efficiency of different coagents were characterized by cure study on EOC gum vulcanizate. TAC showed the highest torque values followed by MPDM and TMPTA. Significant improvements in the physical properties of the TPVs were inferred with the addition of coagents. Among the three coagents used, MPDM showed the best balance of mechanical properties in these TPVs. The results indicated that torque values obtained during mixing and the final mechanical properties can be correlated. Different aspects were explained for the selection of a coagent that forms a product with desired properties. The phase morphologies of the TPVs prepared were studied by scanning electron microscopy. Tensile fracture patterns were also analyzed to study the failure mechanism of the samples. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Study on the microstructure and properties of bromobutyl rubber (BIIR)/polyamide‐12 (PA12) thermoplastic vulcanizates (TPVs)

In this study, polyamide‐12 (PA12)/brominated isobutylene‐isoprene (BIIR) TPVs with good mechanical properties and low gas permeability were prepared by dynamic vulcanization in a twin‐screw extruder. The effects of three kinds of compatibilizers on the microstructure and properties of BIIR/PA12 TPV were studied. The compatibility between BIIR and PA12 was improved when maleated hydrocarbon polymeric compatibilizer is added. The reaction between maleic anhydride and amine in polyamide leads to the in situ formation of hydrocarbon polymer grafted polyamide which subsequently can be used to lower the interfacial tension between BIIR and polyamide. The compatibilizing effect of maleic anhydride modified polypropylene (PP‐g‐MAH) on BIIR/PA12 blends is the best among these compatibilizers because the surface energy of PP‐g‐MAH is very close to that of BIIR. The dispersed rubber phase of the blend compatibilized by PP‐g‐MAH shows the smallest size and more uniform size distribution, and the resulting TPVs show the best mechanical properties. The effects of fillers on the properties of BIIR/PA12 TPV were also investigated. The size of the BIIR phase increases with the increase in the content of CaCO₃. The modulus and tensile strength of TPVs increased with the increase in the content of CaCO₃ because of the reinforcing effect of CaCO₃ on TPVs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43043.     

Thermoplastic vulcanizates based on epoxidized natural rubber/polypropylene blends: Effect of compatibilizers and reactive blending

Epoxidized natural rubber (ENR) was prepared using the performic epoxidation method. TPVs based on ENR/PP blends were later prepared by melt‐mixing processes via dynamic vulcanization. The effects of blend ratios of ENR/PP, types of compatibilizers, and reactive blending were investigated. Phenolic modified polypropylene (Ph‐PP) and graft copolymer of maleic anhydride on polypropylene molecules (PP‐g‐MA) were prepared and used as blend compatibilizers and reactive blending components of ENR/Ph‐PP and ENR/PP‐g‐MA blends. It was found that the mixing torque, apparent shear stress and apparent shear viscosity increased with increasing levels of ENR. This is attributed to the higher viscosity of the pure ENR than that of the pure PP. Furthermore, there was a higher compatibilizing effect because of the chemical interaction between the polar groups in ENR and PP‐g‐MA or Ph‐PP. Mixing torque, shear flow properties (i.e., shear stress and shear viscosity) and mechanical properties (i.e., tensile strength, elongation at break, and hardness) of the TPVs prepared by reactive blending of ENR/Ph‐PP and ENR/PP‐g‐MA were lower than that of the samples without a compatibilizer. However, the TPVs prepared using Ph‐PP and PP‐g‐MA as compatibilizers exhibited higher values. We observed that the TPVs prepared from ENR/PP with Ph‐PP as a compatibilizer gave the highest rheological and mechanical properties, while the reactive blending of ENR/PP exhibited the lowest values. Trend of the properties corresponds to the morphology of the TPVs. That is, the TPV with Ph‐PP as a blend compatibilizer showed the smallest rubber particles dispersed in the PP matrix, while the reactive blending of ENR/PP‐g‐MA showed the largest particles. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4729–4740, 2006     

Process–structure–property relationship in ternary short‐glass‐fiber/elastomer/polypropylene composites

Short‐glass‐fiber (SGF)‐reinforced polypropylene (PP) composites toughened with a styrene/ethylene butylene/styrene (SEBS) triblock copolymer were injection molded after extrusion. Furthermore, a maleic anhydride (MA)‐grafted SEBS copolymer (SEBS‐g‐MA) was used as an impact modifier and compatibilizer. The effects of the processing conditions and compatibilizer on the microstructure and tensile and impact performance of the hybrid composites were investigated. In the route 1 fabrication process, SGF, PP, and SEBS were blended in an extruder twice, and this was followed by injection molding. In route 2, or the sequential blending process, the elastomer and PP were mixed thoroughly before the addition of SGF. In other words, either PP and SEBS or PP and SEBS‐g‐MA pellets were premixed in an extruder. The produced pellets were then blended with SGF in the extruder, and this was followed by injection molding. The SGF/SEBS‐g‐MA/PP hybrid fabricated by the route 2 process exhibited the highest modulus, yield stress, tensile stress at break, Izod impact energy, and Charpy drop weight impact strength among the composites investigated. This was due to the formation of a homogeneous SEBS elastomeric interlayer at the SGF and matrix interface of the SGF/SEBS‐g‐MA/PP hybrid. This SEBS rubbery layer enhanced the interfacial bonding between SGF and the matrix of the SGF/SEBS‐g‐MA/PP hybrid. The correlations between the processing, microstructure, and properties of the hybrids were investigated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1384–1392, 2003     

Blending of styrene‐block‐butadiene‐block‐styrene copolymer with sulfonated vinyl aromatic polymers

Different polymers containing sulfonic groups attached to the phenyl rings were prepared by sulfonation of polystyrene (PS) and styrene‐block‐(ethylene‐co‐1‐butene)‐block‐styrene (SEBS). The sulfonation degree (SD) was varied between 1 and 20 mol% of the styrene units. Polyphase materials containing sulfonated units were prepared by blending styrene‐block‐butadiene‐block‐styrene (SBS), with both sulfonated PS and sulfonated SEBS in a Brabender mixer. Such a procedure was performed as an alternative route to direct sulfonation of SBS which is actually not selective towards benzene rings because of the great reactivity of the double bonds in polybutadiene (PB) blocks to sulfonation agents. Thermal and dynamic‐mechanic analysis, together with morphology characterization of the blends, is consistent with obtaining partially compatible blends characterized by higher T_g of the polystyrene domains and improved thermal stability. © 2001 Society of Chemical Industry