Multiwalled carbon nanotube‐filled ethylene acrylic elastomer nanocomposites: Influence of ionic liquids on the mechanical,dynamic mechanical,and dielectric properties

Electrically conductive nanocomposites based on ethylene acrylic elastomer (AEM) and multiwalled carbon nanotube (MWNT) have been successfully prepared. Before mixing the MWNT is dispersed in ethanol in presence of ionic liquids such as 1‐methyl‐3‐octylimidazolium chloride (MOIC) and 1‐allyl‐3‐methyl imidazolium chloride (AMIC). Uniform dispersion of MWNT in the nanocomposites is achieved in presence of ionic liquid, which is confirmed by the high‐resolution transmission electron microscopic (HRTEM) microphotographs. The tensile strength increases up to 6 phr of MWNT loading and above that it decreases. However, the tensile strength increases due to the incorporation of ionic liquid assisted dispersed MWNT. It is observed from the dynamic mechanical analysis (DMA) that the storage modulus (E′) and glass transition temperature (T_g) of AEM matrix increase by incorporation of MWNT. The E′ also increases and the tan δ_max marginally decreases due to the incorporation of dispersed MWNT in presence of ionic liquids. The dielectric relaxation characteristic properties of AEM/MWNT nanocomposites such as dielectric permittivity (ε′), AC conductivity (σ_ac), impedance (Z^*) have been studied as a function of frequency (10¹−10⁶ Hz) in presence of ionic liquids. The ε′ and σ_ac increase with increasing the MWNT loading due to the easy orientation of dipoles and formation of interconnected conductive networks in the nanocomposites. The electromagnetic interference shielding effectiveness (EMISE) is studied in the X‐band frequency range of 8 to 12 GHz, which significantly improved with increase in MWNT loading. POLYM. COMPOS., 37:2568–2580, 2016. © 2015 Society of Plastics Engineers     

Nonisothermal crystallization kinetics and thermomechanical properties of multiwalled carbon nanotube‐reinforced poly(ε‐caprolactone) composites

BACKGROUND: The technological development of poly(ε‐caprolactone) (PCL) is limited by its short useful lifespan, low modulus and high crystallinity. There are a few papers dealing with the crystallization behavior of carbon nanotube‐reinforced PCL composites. However, little work has been done on the crystallization kinetics of melt‐compounded PCL/multiwalled carbon nanotube (MWNT) nanocomposites. In this study, PCL/MWNT nanocomposites were successfully prepared by a simple melt‐compounding method, and their morphology and mechanical properties as well as their crystallization kinetics were studied. RESULTS: The MWNTs were observed to be homogeneously dispersed throughout the PCL matrix. The incorporation of a very small quantity of MWNTs significantly improved the storage modulus and loss modulus of the PCL/MWNT nanocomposites. The nonisothermal crystallization behavior of the PCL/MWNT nanocomposites exhibits strong dependencies of the degree of crystallinity (X_c), peak crystallization temperature (T_p), half‐time of crystallization (t_1/2) and Avrami exponent (n) on the MWNT content and cooling rate. The MWNTs in the PCL/MWNT nanocomposites exhibit a higher nucleation activity. The crystallization activation energy (E_a) calculated with the Kissinger model is higher when a small amount of MWNTs is added, then gradually decreases; all the E_a values are higher than that of pure PCL. CONCLUSION: This paper reports for the first time the preparation of high‐performance biopolymer PCL/MWNT nanocomposites prepared by a simple melt‐compounding method. The results show that the PCL/MWNT nanocomposites can broaden the applications of PCL. Copyright © 2008 Society of Chemical Industry     

Preparation and characterization of poly(vinylidene fluoride) nanocomposites containing multiwalled carbon nanotubes

Poly(vinylidene fluoride) (PVDF) nanocomposites with different loadings of multiwalled carbon nanotubes (MWNT) were prepared by melt‐compounding technique. A homogeneous dispersion of MWNT throughout PVDF matrix was observed on the cryo‐fractured surfaces by scanning electron microscopy. Thermogravimetric analysis results indicated that the thermal stability of neat PVDF was improved with the incorporation of MWNT. Dynamic mechanical analysis showed a significant improvement in the storage modulus over a temperature range from ?125 to 75°C with the addition of MWNT. The melt‐rheological studies illustrated that incorporating MWNT into PVDF matrix resulted in higher complex viscosities (|η*|), storage modulus (G′), loss modulus (G″), and lower loss factor (tan δ) than those of neat PVDF. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology,thermal, and rheological behavior of nylon 11/multi‐walled carbon nanotube nanocomposites prepared by melt compounding

Nylon 11 (PA11) nanocomposites with different loadings of multi‐walled carbon nanotubes (MWNTs) were prepared by melt compounding. Scanning electron microscopy images on the fracture surfaces of the composites showed a uniform dispersion of MWNTs throughout the matrix. The presence of the MWNTs significantly improved the thermal stability and enhanced the storage modulus (G′) of the polymer matrix. Melt rheology studies showed that, compared with neat PA11, the incorporation of MWNT into the matrix resulted in higher complex viscosities (|η*|), storage modulus (G′), loss modulus (G″), and lower loss factor (tanδ). PA11 and its nanocomposites containing less than 1 wt% MWNTs showed similar frequency dependencies and reached a Newtonian plateau at low frequencies. For the nanocomposite with 2 wt% MWNTs, the regional network was destroyed and the orientation of the MWNTs during shearing exhibited a very strong shear thinning effect. The complex viscosities (|η*|) of the nanocomposites are larger than that of neat PA11 and decreased with increasing the temperature. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Effects of amino‐functionalized carbon nanotubes on the properties of amine‐terminated butadiene–acrylonitrile rubber‐toughened epoxy resins

Amino‐functionalized multiwalled carbon nanotubes (MWCNT‐NH₂s) as nanofillers were incorporated into diglycidyl ether of bisphenol A (DGEBA) toughened with amine‐terminated butadiene–acrylonitrile (ATBN). The curing kinetics, glass‐transition temperature (T_g), thermal stability, mechanical properties, and morphology of DGEBA/ATBN/MWCNT‐NH₂ nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis, a universal test machine, and scanning electron microscopy. DSC dynamic kinetic studies showed that the addition of MWCNT‐NH₂s accelerated the curing reaction of the ATBN‐toughened epoxy resin. DSC results revealed that the T_g of the rubber‐toughened epoxy nanocomposites decreased nearly 10°C with 2 wt % MWCNT‐NH₂s. The thermogravimetric results show that the addition of MWCNT‐NH₂s enhanced the thermal stability of the ATBN‐toughened epoxy resin. The tensile strength, flexural strength, and flexural modulus of the DGEBA/ATBN/MWCNT‐NH₂ nanocomposites increased increasing MWCNT‐NH₂ contents, whereas the addition of the MWCNT‐NH₂s slightly decreased the elongation at break of the rubber‐toughened epoxy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40472.     

Synthesis and characterization of polyimide/multi‐walled carbon nanotube nanocomposites

Polyimide/multi‐walled carbon nanotube (PI‐MWNT) nanocomposites were fabricated by an in situ polymerization process. Chemical compatibility between the PI matrix and MWNTs is achieved by pretreatment of the carbon nanotubes in a mixture of sulfuric acid and nitric acid. The dispersion of MWNTs in the PI matrix was found to be enhanced significantly after acid modification. The glass transition (T_g) and decomposition (T_d) temperature of PI‐MWNT nanocomposites were improved as the MWNT content increased from 0.5 to 15 wt%. The storage modulus of the PI/MWNT nanocomposites is nine times higher than that of pristine PI at room temperature. The tensile strength of PI doubles when 7 wt% MWNTs is added. The dielectric constant of the PI‐MWNT nanocomposites increased from 3.5 to 80 (1 kHz) as the MWNT content increased to 15 wt%. The present study demonstrates that enhanced mechanical properties can be obtained through a simple in‐situ polymerization process. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Fabrication and characterization of the mechanical properties of multi-walled carbon nanotube-reinforced epoxy resins by e-beam irradiation

In this study, the multi-walled carbon nanotubes (MWNT) were reinforced to epoxy resin as fabrication of epoxy/MWNT nanocomposites by electron beam (e-beam) curing. An attempt is made to disperse MWNT into diglycidyl ether of bisphenol A (DGEBA) as epoxy resins, using triarylsulfonium hexafluoroantimonate (TASHFA) as an initiator. E-beam irradiation effect on the curing of the epoxy resin was investigated in oxygen and nitrogen atmospheres at room temperature. The flexural modulus was measured by a universal testing machine (UTM). Here, the flexural modulus factor exhibits an upper limit at 0.3 wt% MWNT. The dynamic mechanical and thermal properties of the irradiated epoxy resins were characterized using DMA, DSC and TGA machines. DMA curves of the storage modulus revealed an increase with an increasing MWNT content and radiation dose. However, the T_g curve decreased as a function of the increasing MWNT content and radiation dose. The thermal properties of the TGA and DSC data were improved by increasing the content of the MWNT and the radiation dose. Likewise, the thermal properties were stabilized by increasing the amount of initiator and irradiating the resins in a nitrogen atmosphere.     

Effect of functionalized nanosilica on the mechanical,dynamic‐mechanical,and morphological performance of polycarbonate/nanosilica nanocomposites

Polycarbonate (PC)/nanosilica (nSiO₂) nanocomposites were prepared by melt‐blending technique, in which surfactants are used to enhance the interfacial adhesion between nSiO₂ and polymer matrix. Mechanical properties demonstrate increased Young's modulus and yield strength of modified PC/nSiO₂ nanocomposites when compared with PC. Increased compatibility further indicates an effective increase in thermal stability as observed from thermogravimetric analysis. Dynamic mechanical analysis point out a reduction in T_g value with increased storage modulus. The flammability characteristics of PC/nSiO₂ nanocomposites were evaluated using limiting oxygen index, whereas the morphological properties are characterized by wide‐angle X‐ray diffraction and scanning electron microscopy. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Rheological properties of poly(acrylonitrile‐co‐methyl acrylate)/clay nanocomposites prepared via emulsion polymerization

Poly(acrylonitrile‐co‐methyl acrylate)/clay nanocomposites were prepared by free radical polymerization in emulsion using 2‐acrylamido‐2‐methyl‐1‐propanesulphonic acid (AMPS) as a compatibilizer. The resultant nanocomposites were of partially exfoliated morphology despite the variations in clay content among the nanocomposites, as confirmed by transmission electron microscopy and small‐angle X‐ray scattering analysis. Rheological studies of these materials were carried out using parallel plate geometry. The storage modulus increased monotonically with increasing clay content throughout the frequency range studied. However, the neat copolymer, poly(acrylonitrile‐co‐methyl acrylate) and its nanocomposites, exhibited long relaxation behavior as the storage modulus (G′) was greater than the loss modulus (G″) throughout the angular frequency range studied. The complex viscosity of the nanocomposites increased with increasing clay content and they exhibited shear‐thinning behavior. Despite the enhanced rheological properties observed, the copolymer and its nanocomposites underwent structural changes during oscillatory measurements due to cyclization reactions. POLYM. COMPOS., 32:59–66, 2011. © 2010 Society of Plastics Engineers     

Synthesis of s‐triazine‐based hyperbranched polyurethane for novel carbon‐nanotube‐dispersed nanocomposites

s‐Triazine‐based hyperbranched polyurethanes (HBPUs) with different hard segments were synthesized by A₂ + B₃ approach. Various kinds of multiwalled carbon nanotube (MWNT) nanocomposites with HBPU were prepared to investigate an impact of hyperbranched polymer on dispersion of MWNTs in the polymer matrix and the resulting properties of nanocomposites. Synthesized HBPUs were characterized using FTIR and NMR measurements. The highly branched structures were found very effective in enhancing the pristine MWNT dispersion in the polymer matrix. As a result, the MWNT‐reinforced HBPU nanocomposites showed a steep increase in the yield stress and modulus and enhanced shape memory effect with an increase of hard segment and MWNT loading. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and properties of in‐situ polymerized polyurethane/stearate intercalated layer double hydroxide nanocomposites

The present work deals with the effect of stearate intercalated layered double hydroxide (St‐LDH) loadings on the morphological, mechanical, thermal, adhesive and flame retardant properties of polyurethane (PU)/St‐LDH nanocomposites prepared by the in situ polymerization method. X‐ray diffraction and transmission electron microscopy studies confirmed that exfoliation takes place at 3 wt% loading followed by intercalation at higher filler loadings in the PU matrix. The exfoliated structure has been further verified by atomic force microscopy. The measurements of stress‐strain, thermogravimetric analysis, dynamic mechanical analysis, lap shear strength and peel strength analysis showed that the nanocomposites containing 3 wt% St‐LDH exhibit excellent improvement in tensile strength (ca 175%) and log storage modulus (ca 14%), while PU/St‐LDH (5 wt%) possesses optimum improvement in glass transition temperature (ca 6 °C), lap shear strength (200%) and peel strength (130%) over neat PU. In addition, the gradual improvements in limiting oxygen index value with St‐LDH loading indicated the higher effectiveness in providing better barrier properties as well as better flame retardant behavior. Copyright © 2012 Society of Chemical Industry     

Thermal and mechanical properties of carbon nanotube/epoxy nanocomposites reinforced with pristine and functionalized multiwalled carbon nanotubes

In this study, the effects of functionalization and weight fraction of mutliwalled carbon nanotubes (CNTs) were investigated on mechanical and thermomechanical properties of CNT/Epoxy composite. Epoxy resin was used as matrix material with pristine‐, COOH‐, and NH₂‐functionalized CNTs as reinforcements in weight fractions of 0.1, 0.5, and 1.0%. Varying (increasing) the weight fraction and changing type (pristine or functionalized) of CNTs caused increment in Young's modulus and tensile strength as observed during mechanical tests. CNT reinforcement improved thermal stability of the nanocomposites as observed by thermogravimetric analysis. Thermomechanical analysis showed a slight reduction in free volume of the polymer, that is a drop in coefficient of thermal expansion, prior to glass transition temperature (T_g) beside a slight increase in T_g value. Dynamic mechanical analysis indicated an increase in storage modulus and T_g owing to the strength addition of CNT to the matrix alongside the hardener. Scanning electron microscopy analysis of the fractured surface(s) revealed that CNTs were well dispersed with no agglomeration and resulted in reinforcing the matrix. POLYM. COMPOS., 36:1891–1898, 2015. © 2014 Society of Plastics Engineers     

Synthesis and characterization of elastomeric polyurethane and PU/clay nanocomposites based on an aliphatic diisocyanate

This investigation reports preparation of polyurethane and polyurethane/clay nanocomposites based on polyethylene glycol, isophorone diisocyanate (IPDI), an aliphatic diisocyanate and 1,4‐ Butanediol as chain extender by solution polymerization. In this case PU/clay nanocomposites were prepared via ex‐situ method using 1, 3, and 5 wt % of Cloisite 30B. Thermogravimetric analysis showed that the maximum decomposition temperature (T_max) of the PU/clay nanocomposite is much higher than the pristine PU. The tensile properties improved upon increasing the organoclay (Cloisite 30B) content upto 3 wt %, and then decreased to some extent upon further increasing the nanoparticle loading to 5 wt %. Optical properties of the nanocomposites were studied by UV‐vis spectrophotometer. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) were used to study the morphology of the nanocomposites. It was observed that with the incorporation of 3 wt % nanoclay the crystallinity in PU nanocomposite increases, then diminishes with further loading. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3328–3334, 2013     

Synthesis,characterization and properties of organoclay‐modified polyurethane/epoxy interpenetrating polymer network nanocomposites

organoclay‐modified polyurethane/epoxy interpenetrating network nanocomposites (oM‐PU/EP nanocomposites) were prepared by adding organophilic montmorillonite (oMMT) to interpenetrating polymer networks (IPNs) of polyurethane and epoxy resin (PU/EP) which had been prepared by a sequential polymerization technique. Wide‐angle X‐ray diffraction (WAXD) and transmission electronic microscopy (TEM) analysis showed that the interpenetrating process of PU and EP improved the exfoliation and dispersion degree of oMMT. The effects of the NCO/OH ratio (isocyanate index), the weight ratio of PU/EP and oMMT content on the phase structure and the mechanical properties of the oM‐PU/EP nanocomposites were studied by tensile testing and scanning electronic microscopy (SEM). Water absorption tests showed that the PU/EP interpenetrating networks and oMMT had synergistic effects on improvement in the water resistance of the oM‐PU/EP nanocomposites. Differential scanning calorimetry (DSC) analysis showed that PU was compatible with EP and that the glass transition temperature (T_g) of the oM‐PU/EP nanocomposites increased with the oMMT content up to 3 wt%, and then decreased with further increasing oMMT content. The thermal stability of these nanocomposites with various oMMT contents was studied by thermogravimetric analysis (TGA), and the mechanism of thermal stability improvement was discussed according to the experimental results. Copyright © 2005 Society of Chemical Industry     

Effect of carbon nanotube on PA6/ECO composites: Morphology development,rheological, and thermal properties

Thermoplastic elastomer (TPE) nanocomposites based on polyamide‐6 (PA6)/poly(epichlorohydrin‐co‐ethylene oxide) (ECO)/multiwall carbon nanotube (MWCNTs) were prepared by melt compounding process. Different weight ratios of ECO (20, 40, and 60 wt %) and two kinds of functionalized and non‐functionalized MWCNTs were employed to fabricate the nanocomposites. The morphological, rheological, and mechanical properties of MWCNTs‐filled PA6/ECO blends were studied. The scanning electron microscopy of PA6/ECO blends showed that the elastomer particles, ECO, are well‐dispersed within the PA6 matrix. The significant improvement in the dispersibility of the carboxylated carbon nanotubes (COOH‐MWCNTs) compared to that of non‐functionalized MWCNTs (non‐MWCNTs) was confirmed by transmission electron microscopy images. The tensile modulus of samples improved with the addition of both types of MWCNTs. However, the effect of COOH‐MWCNTs was much more pronounced in improving mechanical properties of PA6/ECO TPE nanocomposites. Crystallization results demonstrated that the MWCNTs act as a nucleation agent of the crystallization process resulted in increased crystallization temperature (T_c) in nanocomposites. Rheological characterization in the linear viscoelastic region showed that complex viscosity and a non‐terminal storage modulus significantly increased with incorporation of both types of MWCNTs particularly at low frequency region. The increase of rheological properties was more pronounced in the presence of carboxylic (COOH) functional groups, in the other words by addition of COOH‐MWCNTs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45977.     

In situ Polymerization of Multi-Walled Carbon Nanotube/Nylon-6 Nanocomposites and Their Electrospun Nanofibers

Multiwalled carbon nanotube/nylon-6 nanocomposites (MWNT/nylon-6) were prepared by in situ polymerization, whereby functionalized MWNTs (F-MWNTs) and pristine MWNTs (P-MWNTs) were used as reinforcing materials. The F-MWNTs were functionalized by Friedel-Crafts acylation, which introduced aromatic amine (COC₆H₄-NH₂) groups onto the side wall. Scanning electron microscopy (SEM) images obtained from the fractured surfaces of the nanocomposites showed that the F-MWNTs in the nylon-6 matrix were well dispersed as compared to those of the P-MWNTs. Both nanocomposites could be electrospun into nanofibers in which the MWNTs were embedded and oriented along the nanofiber axis, as confirmed by transmission electron microscopy. The specific strength and modulus of the MWNTs-reinforced nanofibers increased as compared to those of the neat nylon-6 nanofibers. The crystal structure of the nylon-6 in the MWNT/nylon-6 nanofibers was mostly γ-phase, although that of the MWNT/nylon-6 films, which were prepared by hot-pressing the pellets between two aluminum plates and then quenching them in icy water, was mostly α-phase, indicating that the shear force during electrospinning might favor the γ-phase, similarly to the conventional fiber spinning.     

Structure and properties of polypropylene/hydrotalcite nanocomposites

This article presents the study of the modification of the particle/matrix interface region and its effects on the structure and dynamic mechanical behavior of polypropylene (PP)/hydrotalcite nanocomposites prepared by melt extrusion. The interface modification was promoted by combinying the organophillization of the hydrotalcite particles with blending the PP with a maleic anhydride‐grafted‐PP (PP‐g‐MAH) or a maleic anhydride‐grafted‐poly(styrene‐co‐ethylenebutylene‐co‐styrene) (SEBS‐g‐MAH). Sodium dodecyl sulphate was used to promote the organophillization of the hydrotalcite particles. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) showed a partially exfoliated hydrotalcite structure, with an increasing exfoliation being achieved by adding a compatibilizer and organo‐modifying the particles. Values of the Young's modulus (E), storage modulus (E′), maximum tensile strength (σ_max), neck propagation strength (σ_neck), and elongation at break (ε_b) were found to depend both on the nature of the particle matrix interface as well as on the type of compatibilizer. Also, nanocomposites prepared with the organophillized particles showed lower T_g and loss factor values. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Modification of chitosan-Fe3O4 microspheres with isophorone diisocyanate and formation of polyurethane/mchitosan-Fe3O4 antimicrobial polymer

Polyurethane/modified chitosan-Fe₃O₄ (PU/mCS-Fe₃O₄) nanocomposites were prepared by incorporating chitosan-Fe₃O₄ (CS-Fe₃O₄) into PU through chemical grafting using isophorone diisocyante (IPDI). The isocyanate group of IPDI was introduced on the surface of CS-Fe₃O₄ nanocomposites. The chemical functionalities of the CS-Fe₃O₄ and mCS-Fe₃O₄ were verified by Fourier-transform infrared and X-ray diffraction. The structure and properties were confirmed by scanning electron microscope, vibrating sample magnetometer, thermogravimetric analysis, atomic force microscope, and tensile testing. The experimental results indicate that thermal stability, tensile strength, and storage modulus of nanocomposites were improved with the increasing content of mCS-Fe₃O₄. Meanwhile, PU/mCS-Fe₃O₄ nanocomposites have less cytotoxicity and good antibacterial activities againstEscherichia coli and Staphylococcus aureus.     

A polycaprolactone‐based compatibilization treatment to improve dispersion and interphase structure of silica polyurethane composites

Silica nanoparticles (SNs) were grafted with ε ‐caprolactone using an environmentally friendly approach. By using tartaric acid as a catalyst and the silanol groups as initiators, grafted nanoparticles (GNs) with organic weight fractions (w_of) within the range 0–46 wt% were synthesized. Thermogravimetric (TGA) and infrared analysis were used to measure the w_of and to corroborate the covalent bond between the SN and the caprolactone monomer. Transmission electron micrographs of the polyurethane (PU) nanocomposites based on the SN and the GN revealed that the interfacial area of the GN‐based PU increased by the reduction of agglomerate dimensions from 10 µm to around 0.1 µm. Dynamic mechanical analysis showed that the GN nanocomposites improved the storage shear modulus from 616±11 to 849±8 MPa for a GN with w_of = 16.7% and 3 wt% filler concentration. In addition, the GN particles prevented a relevant decrease of the transition temperature (T_g). Differential scanning calorimetry corroborated that GN increased the enthalpic energy associated to the physical crosslinking of the hard segments (HS). Wide‐angle X‐ray diffraction proved that the GN formed a HS structure with improved crystallinity. The thermal stability of the GN‐based PU a nanocomposite was improved by an increase of the thermal stability of the castor oil soft segments. POLYM. ENG. SCI., 54:1817–1826, 2014. © 2013 Society of Plastics Engineers     

Mechanical and electrical multifunctional poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)—multiwall carbon nanotube nanocomposites

In this work, nanocomposites of poly(hydroxybutyrate‐co‐hydroxyvalerate) PHBV and multiwalled carbon nanotubes (MWNT) were prepared by melt blending. Mechanical, thermal, morphological, and electrical properties of the prepared PHBV/MWNT nanocomposites were investigated. Differential scanning calorimetry (DSC) and X‐ray diffraction (XRD) results showed MWNT effectively enhanced the crystallization and nucleation of PHBV. Dynamic thermo‐mechanical and static uniaxial mechanical tensile and compressive properties were increased by the addition of MWNT. MWNT observed in the nanocomposites using transmission electron microscopy (TEM) showed dimensions similar to separated nanotubes inferring a good dispersion. The presence of nanotubes in close vicinity with each other formed an interconnecting network that led to the formation of electrically conductive nanocomposites. The electrical resistance of the nanocomposites was reduced with the addition of MWNT. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers