TiO2/CdS复合光催化剂的制备及结构研究

以钛酸四丁脂为原料、乙醇为溶剂、醋酸为水解抑制剂,采用溶胶-凝胶法制备CdS纳米颗粒改性TiO2光催化剂凝胶.系统地研究了干凝胶的热行为,在不同热处理温度下二氧化钛的晶体结构和二氧化钛热处理温度与晶粒度之间的关系.研究表明,670℃/3h焙烧后,TiO2由锐钛矿结构全部转变为金红石结构;当CdS的掺入量大于6%(mol)时,670℃/3h焙烧后,有CdTiO3新物相生成;CdS的掺入抑制了锐钛矿TiO2晶粒的长大和锐钛矿结构向金红石结构的转变.     

纳米TiO2粉体的制备及其表征

采用溶胶-凝胶技术制备了纳米TiO2粉体,并对其热性能、相结构、颗粒大小和分布进行了表征,结果表明,TiO2干凝胶粉经300℃煅烧后已有锐钛矿相出现,经550℃煅烧后有金红石相出现,完全相转变的温度约为600℃,纳米TiO2粉体的颗粒尺寸随煅烧温度的升高而增大,采用溶胶,凝胶技术制备的干凝胶粉经400℃煅烧后可获得团聚轻、颗粒大小分布比较均匀、颗粒尺寸约为15nm的球状TiO2粉体,     

热处理对片状TiO2微粒相变的影响

用化学处理法制备了片状TiO2微粒，并对片状TiO2微粒及其焙烧产物的形貌和物相进行了分析。结果发现：片状TiO2微粒为无定型结构，片状颗粒非常薄；当加热到300℃以上时，TiO2片收缩变厚并由无定型转变为锐钛矿型结构．当继续加热使片状TiO2微粒由锐钛矿转变为金红石型结构时，原来的片状TiO2部分转变为长棒状的金红石型晶柱结构，而原料TiO2无论在多高的温度下焙烧都未出现长棒状晶柱结构；片状TiO2微粒的A→R相变温度比原料低大约300℃。     

Ce掺杂对TiO_2晶型转变的影响

以钛酸四丁酯以及六水合硝酸铈为原料,采用溶胶-凝胶法制备了纯的和Ce掺杂的TiO2粉体,研究了不同掺杂量对TiO2晶形转变产生的影响。结果表明,Ce离子的掺杂阻碍了TiO2粒子由锐钛矿型向金红石型的转变,拓宽了锐钛矿型TiO2的使用温度范围;TiO2晶粒的尺寸的变化是随着焙烧温度的升高逐渐长大,随掺杂量的增加逐渐减小。TiO2粉体粒子在锐钛矿型状态下,颗粒分散较为均匀,并且无明显团聚现象。     

热处理对溶胶-凝胶TiO2薄膜的晶相转变和性能影响

以钛酸丁酯（TPOT）为有机醇盐前驱体，采用溶胶－凝胶技术制备了TiO2溶胶。为测量方便起见，分别制备了凝胶粉体和薄膜，并对样品进行了不同温度的热处理。X射线衍射（XRD）、椭偏仪和紫外－可见光谱（UV－vis)的测量表明：随热处理温度的升高，TiO2的结构由非晶到锐钛矿再到金红石相转变，400℃为锐钛矿相，600℃开始出现金红石相，800℃完全转变为金红石相；晶粒尺寸随热处理温度的升高而逐渐增大，锐钛矿结构的晶粒尺寸范围是2.5-5.5nm，金红石结构的晶粒尺寸范围是5.9-6.8nm；TiO2薄膜的折射率随热处理温度的升高而增大，同时薄膜厚度降低；禁带宽度随热处理温度的升高而增大，同时薄膜厚度降低；禁带宽度随热处理温度升高而变窄，锐钛矿结构的禁带宽度为3.45eV，而金红石结构的禁带宽度为3.30eV。     

纳米二氧化钛粉体晶相控制实验研究

在水解－沉淀法制备纳米TiO2粉体的过程中，使用不同的沉淀剂获得了晶相不同的纳米TiO2粉体，使用混合沉淀剂，通过控制沉淀剂的比例，制备了晶相组成（金红石与锐钛矿比例）不同的纳米TiO2多晶粉体，采用相同的粉体制备工艺，不同的后续处理工艺，探讨了锐钛矿向金红石转变的相变温度，经分析研究后认为，水解－沉淀法制备的纳米粉体中的锐钛矿向金红石红转变的温度为500－800℃，完全转变的温度在800℃以上；纳米TiO2多晶粉体的晶相组成不仅与沉淀剂的种类，混合沉淀剂中沉淀剂的比例和粉体的煅烧温度有关，而且与粉体的后续处理工艺和粉体表面界面相的稳定性有关。     

钛酸盐一维纳米材料向TiO2纳米材料的水热转化研究

采用强碱性水热处理法分别控制第一次水热反应为160℃和200℃,制备出一维纳米管和纳米棒2种形貌的产物,将其作为第二次水热反应的前驱体,考察了第二次水热体系中pH值和温度对TiO2纳米材料的晶相组成及其微观形貌的影响;采用XRD、TEM以及HRTEM对样品进行了分析.结果表明,当以纳米管为前驱体时,除在pH=0的体系中得到了以金红石相为主的单晶纳米棒外,在pH值为2、4和7的条件下均得到了单晶纯锐钛矿相TiO2纳米颗粒.当以纳米棒为前驱体时,在pH=0的体系中得到了金红石相与板钛矿相共存的纳米棒和纳米颗粒混合产物;在pH值为2、4和7的条件下均得到了纯锐钛矿相TiO2纳米棒;当二次水热温度低于180℃时,前驱体没有转化完全,所得产物为前驱体与锐钛矿相TiO2共存的纳米棒;当水热温度为180℃和210℃时,产物为纯锐钛矿相纳米棒.     

纳米TiO2光催化剂的电化学法制备及其表征

采用有机电解-溶胶-凝胶法制备了纳米TiO2光催化剂,通过XRD、TEM、TG-DTA、激光粒度分析法等对纳米TiO2的结构相变、表面形貌、颗粒大小等进行了表征.实验表明:当热处理温度低于350℃时,TiO2的晶相结构均为锐钛型,颗粒大小在25nm以下,样品的比表面积大于65m2*g-1;热处理温度为400℃时,TiO2的晶相结构出现锐钛型和金红石型混合相,颗粒大小在35nm以下,样品比表面积为46.43m2*g-1,实验制备的粉体样品属于纳米级水平;实验测试了各焙烧温度下粉体样品的光催化活性.     

不同介质中水热合成纳米TiO2粉体及其光催化性能研究

以钛酸四丁酯为原料,采用水热法分别以蒸馏水、有机小分子化合物(正丁醇、丙二酸和乙二胺水溶液)和无机酸(HNO3、H2SO4和HCl)为介质合成了TiO2纳米粉体.通过XRD和TEM对所得TiO2粉体进行了表征,研究不同介质对所得TiO2粉体的晶相组成、颗粒尺寸及形貌的影响.结果表明:以蒸馏水为介质时所得锐钛矿TiO2的颗粒尺寸分布不均匀;有机化合物抑制锐钛矿型TiO2各向异性生长趋势的能力为:正丁醇＞丙二酸＞乙二胺;相同实验条件下,HCl、H2SO4及HNO3体系中分别获得金红石、锐钛矿及锐钛矿和金红石混晶TiO2.光催化降解甲基橙的研究表明,锐钛矿和金红石混晶TiO2的光催化活性要高于纯锐钛矿结构;纯金红石型TiO2的光催化活性最差.     

不同晶型的TiO2膜表面光致亲水性的研究

采用Sol-gel法在石英玻璃表面制备了TiO2膜,并经过不同温度焙烧得到不同晶相结构的TiO2膜,同时对膜进行了XRD、UV-Vis紫外-可见吸收光谱、SEM、亲水性的表征和比较.结果表明,TiO2膜在450℃焙烧后转为锐钛矿相结构,而700℃焙烧后则完全转变为金红石相结构.在低强度的紫外光照射下,锐钛矿TiO2膜的亲水性优于金红石和无定型态的TiO2膜;但是当光照强度大于1.0 mW/cm2时,锐钛矿、金红石和无定型TiO2膜的亲水性区别不大,无定型TiO2膜在高强度紫外光照射下表现出良好的亲水性.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.