Performance of metakaolin concrete at elevated temperatures

An experimental investigation was conducted to evaluate the performance of metakaolin (MK) concrete at elevated temperatures up to 800 °C. Eight normal and high strength concrete (HSC) mixes incorporating 0%, 5%, 10% and 20% MK were prepared. The residual compressive strength, chloride-ion penetration, porosity and average pore sizes were measured and compared with silica fume (SF), fly ash (FA) and pure ordinary Portland cement (OPC) concretes. It was found that after an increase in compressive strength at 200 °C, the MK concrete suffered a more severe loss of compressive strength and permeability-related durability than the corresponding SF, FA and OPC concretes at higher temperatures. Explosive spalling was observed in both normal and high strength MK concretes and the frequency increased with higher MK contents.     

环境湿度对玻璃纤维增强水泥力学性能的影响

通过开展在不同龄期、不同环境湿度下玻璃纤维增强水泥(GRC)试件的抗折强度、抗压强度试验和基体pH值测定,研究了环境湿度对掺加粉煤灰和硅灰等活性矿物掺合料的GRC试件力学性能的影响。结果表明:环境湿度对GRC试件的抗折强度有重要影响,相对湿度越大,随着龄期增加, GRC试件抗折强度降低越严重;在温度60℃、相对湿度95%条件下,经过56 d龄期后,掺有40%粉煤灰和10%硅灰的GRC试件抗折强度比未掺加粉煤灰和硅灰的GRC试件的抗折强度提高48.5%、抗压强度提高23.6%, GRC基体pH值降低6%。在相同的湿度条件下,掺有粉煤灰和硅灰试件的pH值在各个龄期都低于普通硅酸盐水泥试件,说明粉煤灰和硅灰的掺入能降低水泥水化液相的碱度,进而延缓了纤维受侵蚀的速度,显著改善了GRC试件的力学及耐久性能。通过对试验结果进行分析,利用MATLAB软件建立了GRC试件抗折强度和抗压强度与水泥砂浆基体pH值及时间的关系式。      

The effect of limestone powder,fly ash and silica fume on the properties of self-compacting repair mortars

Self-compacting repair mortars (SCRM) are preferred for the rehabilitation and repair of reinforced concrete structures especially at narrow mould systems. Self compactability and stability are susceptible to ternary effects of chemical and mineral admixture type and their content. In this study, the effect of limestone powder (LP) on the properties of SCRM has been compared with other mineral additives (silica fume (SF) and fly ash (FA) and their combinations) effects. Fresh properties, flexural and compressive strengths and water absorption properties of mortars were determined. The use of SF in mortars significantly increased the dosage of superplasticiser (SP). At the same constant SP dosage (0·8%) and mineral additives content (30%), LP can better improve the workability than that of control and FA mixtures by 19% and 27%. However, the results of this study suggest that certain FA, SF and LP combinations can improve the workability of SCRMs, more than FA, SF and LP alone. LP can have a positive influence on the mechanical performance at early strength development while SF improved aggregate-matrix bond resulting from the formation of a less porous transition zone in mortar. SF can better reducing effect on total water absorption while FA and LP will not have the same effect, at 28 days.     

Compactness of the Cement Microstructure Versus Crack Bridging in Mortars Reinforced with Amorphous Cast Iron Fibers and Silica Fumes

Both mechanical compaction and addition of pozzolanic silica fumes can provide low permeability interfacial transition zones around the fibers which reinforce a mortar matrix. This paper deals with the controversial effect of achieving a higher matrix compactness and its influence on the fracture behaviour of a mortar reinforced with amorphous cast iron fibers. Test were conducted in uniaxial tension on notched composite mortar prisms in order to plot load versus crack opening curves and evaluate the bridging energy provided by the fibers across a single opening crack. These measures were correlated to SEM observations of the microstructure of fiber/mortar interface, depending on the compaction energy and/or the mortar composition. It is relatively difficult to establish a compromise between ductility and high performance in terms of durability for the material system tested. Indeed, fibers were pulled out of low compactness mortars exhibiting large porous interfacial transition zones (ITZs) along the fiber surface. These zones mainly comprised fibrillous CSH, ettringite and large portlandite crystals. Conversely, when the ITZs around the fibers where filled with compact CSH, resulting from the pozzolanic reaction between silica fume and portlandite, no fiber slippage was observed, but the reinforced mortar broke in a quasi-brittle manner.     

Portland cement-fly ash-silica fume systems in concrete

Laboratory flow, strength, and ultrasnic pulse velocity tests were performed on mortars made with 70% (by weight) of portland cement and 30% of pozzolanic materials where the pozzolanic materials consisted of various combinations of fly ash and silica fume. In addition to these ternary systems, binary blends, such as Portland cement and fly ash, and Portland cement and silica fume, along with 100% Portland cement mortars, were investigated for comparison. The purpose of the investigation, preliminary in nature, was to see under what circumstances, if any, would be a synergistic action when a ternary system of Portland cement-fly ash-silica fume is used in a mortar or concrete.Mortars were made with two cements of type I and two cements of type III along with class F and class C fly ashes. One silica fume was used. Standard flow tests were performed on the fresh mortars, and compressive strength as well as ultrasonic pulse velocity tests were performed with each hardened mortar at various ages up to 28 days. It is expected that the results and conclusions obtained here on mortars will be transferable to concretes.There are several novel, or at least lesser known, results of the investigation. For instance, a new explanation is offered for the plasticizing effect of fly ash which is based on the optimum particle-size distribution concept. Another such result is that ground fly ash produced greater flow increases with type I cement than with type III. A third finding is that the superplasticizer is more effective in increasing the flow as well as strength when the mortars contain fly ash and/or silica fume than in the case of mortars without mineral admixture. Also, it appears that when type I cement is used, the silica fume in the quantity of 5% of the weight of the cement produces relatively greater strength increase in the presence of fly ash than without fly ash.These promising results are preliminary in nature. Therefore, further research is justified with ternary systems in concrete. The presented work is a portion of a larger investigation.     

Effect of metakaolin and silica fume on the durability of self-consolidating concrete

Metakaolin (MK) is a valuable admixture for concrete/cement applications that can enhance the performance of cementitious composites through high pozzolanic reactivity, much like silica fume (SF). While SF concrete is characterized by superior mechanical and durability performance, concrete containing MK achieves comparable properties at a lower price and with better workability. The objective of this study is to investigate the effect of cement replacement by MK on the durability of self-consolidating concrete (SCC); the effect of SF at similar levels of MK replacement has also been included for comparison. The durability performance of SCC was evaluated based on the results of drying shrinkage, freezing and thawing, salt scaling, and rapid chloride permeability tests. The results of these tests indicate that highly durable SCC mixtures can be produced using a high MK content with an optimum percentage of around 20%. The results also show that the durability of SCC, especially with high MK content, is higher than that of SCC containing SF.     

Performance of blended metakaolin/blastfurnace slag alkali-activated mortars

This paper studies the effect of silicate content on the mechanical and durability-related properties of metakaolin (MK) and metakaolin/blastfurnace slag (BFS) alkaline activated mortars. A reference mortar based on the alkaline activated MK was compared to 60/40 MK/BFS mortars containing different SiO₂/Na₂O molar ratios in the activator. The properties assessed were compressive strength, porosity (water saturation), porosity and pore size distribution by Mercury Intrusion Porosimetry (MIP) and water capillary sorption. The microstructure was assessed using SEM and x-ray computerized micro-tomography (μ-CT). Results show that the addition of BFS significantly alters the microstructure of alkali-activated mortars, promoting a reduction of porosity and capillary sorption. In addition, an optimum SiO₂/Na₂O molar ratio in the activator is required to produce better durability mortars, which however do not necessarily present the highest mechanical strength.     

The fluid transport properties of HCWA–DSF hybrid supplementary binder mortar

It has been demonstrated in several past studies that high calcium wood ash (HCWA) can be effectively used in combination with densified silica fume (DSF) as supplementary binder material to enhance the mechanical performance of concrete. The experimental investigation was conducted to study the effect of the inclusion of HCWA and DSF on the durability properties of high strength cement mortar produced. A total of twelve different mix designs of mortar were fabricated with the use of HCWA at various cement replacement levels of 0–20% in combination with 7.5% densified silica fume (DSF) and subjected to various durability tests. The durability assessments performed include tests on water absorption, air permeability, porosity and degree of carbonation. A significantly lower degree of water absorption, porosity and carbonation was observed for cement mortars with HCWA contents of 2–8% used in combination with 7.5% DSF by weight of binder as compared to an equivalent pure cement mortar.     

Use of natural zeolite as a supplementary cementitious material

Natural zeolite, a type of frame-structured hydrated aluminosilicate mineral, is used abundantly as a type of natural pozzolanic material in some regions of the world. In this work, the effectiveness of a locally quarried zeolite in enhancing mechanical and durability properties of concrete is evaluated and is also compared with other pozzolanic admixtures. The experimental tests included three parts: In the first part, the pozzolanic reactivity of natural zeolite and silica fume were examined by a thermogravimetric method. In this case, the results indicated that natural zeolite was not as reactive as silica fume but it showed a good pozzolanic reactivity. In the second part, zeolite and silica fume were substituted for cement in different proportions in concrete mixtures, and several physical and durability tests of concrete were performed. These experimental tests included slump, compressive strength, water absorption, oxygen permeability, chloride diffusion, and electrical resistivity of concrete. Based on these results, the performance of concretes containing different contents of zeolite improved and even were comparable to or better than that of concretes prepared with silica fume replacements in some cases. Finally, a comparative study on effect of zeolite and fly ash on limiting ASR expansion of mortar was performed according to ASTM C 1260 and ASTM C 1567. Expansion tests on mortar prisms showed that zeolite is as effective as fly ash to prevent deleterious expansion due to ASR.     

The effect of processed fly ashes on the durability and the corrosion of steel rebars embedded in cement–modified fly ash mortars

This paper deals with the study of corrosion level of reinforcing steel bars embedded in Portland cement mortars containing different types of fly ash. Fly ashes used were obtained by physico-chemical treatments of an original F class fly ash to modify their magnetic properties and reduce their particle size. An original fly ash (T0) and three types of modified ashes were tested according to treatment duration and magnetic properties (T60, ground fly ash; TNM, non-magnetic fraction; TM, magnetic fraction). Corrosion tests on reinforced mortar specimens with and without different types of fly ashes, cured at 40 °C, and under accelerated carbonation conditions and seawater immersion, have been performed in order to obtain conclusions on durability. From the corrosion point of view the addition of TNM in mortars showed to be much more effective than addition of the original T0 fly ash.     

Compressive strength and drying shrinkage of fly ash-bottom ash-silica fume multi-blended cement mortars

This paper studies the physical properties, compressive strength and drying shrinkage of multi-blended cement under different curing methods. Fly ash, ground bottom ash and undensified silica fume were used to replace part of cement up to 50% by weight. Specimens were cured in air at ambient temperature, water at 25, 40 and 60 °C, sealed with plastic sheeting for 28 days. The results show that absorption and volume of permeable pore space (voids) of blended cement mortars at 28 day under all curing methods tend to increase with increasing silica fume replacement. The compressive strength of blended cement with fly ash and bottom ash was lower than that of Portland cement control at all curing condition while blended cement with silica fume shows higher compressive strength. In addition, the compressive strength of specimens cured with water increased with increasing curing temperature. The drying shrinkage of all blended cement mortar cured in air was lower than that of Portland cement control while the drying shrinkage of blended cement mortar containing silica fume, cured with plastic sealed and water at 25 °C was higher than Portland cement control due to pore refinement and high autogenous shrinkage. However, the drying shrinkage of blended cement mortar containing SF cured with water at 60 °C was lower than that of Portland cement control due to lower autogenous shrinkage and the reduced microporosity of C–S–H.     

Study of interfacial microstructure,fracture energy,compressive energy and debonding load of steel fiber-reinforced mortar

The properties of the interfacial transition zone (ITZ) of steel fiber and the bulk matrix were quantified using the backscattered electron imaging analysis (BSE-IA) and the scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), and their relationship with the mechanical properties of steel fiber-reinforced mortars was studied. The water and binder ratio (w/b) of mortar, the amount of silica fume and steel fiber were varied. From the quantitative analysis, a higher build-up of calcium hydroxide was found from the steel fiber’s interface up to 2 or 4 μm distance away and its build-up was reduced with the 10% cement replacement by silica fume. Porosity in the ITZ and bulk matrix decreased the fracture energy, compressive energy and debonding load of steel fiber-reinforced mortar. However, its effect became marginal if a substantial amount of C–S–H or steel fibers appeared in the ITZ and bulk matrix, which increased the studied mechanical properties.     

Optimization of rheological properties of oil well cement slurries using experimental design

This paper proposes a statistical design approach based on a second order central composite response surface model to predict the rheological properties of oil well cement (OWC) slurries incorporating metakaolin (MK), silica fume (SF), rice husk ask (RHA) or fly ash (FA). The proposed models are for OWC partial replacement levels ranging from 5 to 15% by MK, SF, RHA or FA used along with a new generation polycarboxylate-based high-range water reducing admixture (PCH) at dosages ranging from 0.25 to 1.5% and at different temperatures ranging from 23 to 60°C. The significance and validity of the models were confirmed by statistical analysis and verification experiments. The regression models were used to analyze the influence of the mixture proportion as well as temperature on the rheological properties of OWC slurries. The statistical design can be applied to optimize rheological properties such as yield stress and plastic viscosity considering the addition of supplementary cementitious materials (SCMs) at different temperatures, and to gain a better understanding of trade-offs between key mixture parameters such as the superplasticizer dosage and the level of SCMs used.     

Effect of admixtures on the setting times of high-strength concrete

The effect of silica fume (SF), metakaolin (MK), fly ash (FA) and ground granulated blast-furnace slag (GGBS) on the setting times of high-strength concrete has been investigated using the penetration resistance method (ASTM C 403). In addition, the effect of a shrinkage-reducing admixture (SRA) on the setting times of normal and high-strength concrete was also studied. The setting times of the high-strength concrete were generally retarded when the mineral admixtures replaced part of the cement. While the SRA was found to have negligible effect on the setting times of normal strength concrete, it exhibited a rather significant retarding effect when used in combination with superplasticiser in high-strength concrete. The inclusion of GGBS at replacement levels of 40% and greater resulted in significant retardation in setting times. In general, as replacement levels of the mineral admixtures were increased, there was greater retardation in setting times. However, for the concrete containing MK, this was only observed up to a replacement level of 10%.     

Optimization of concrete mixture with hybrid blends of metakaolin and fly ash using response surface method

This paper presents the experimental results of a research carried out on the strength and permeability related properties of high performance concretes made with binary and ternary cementitious blends of fly ash (FA) and metakaolin (MK). The replacement ratios for FA were 10% and 20% by weight of Portland cement and those for MK were 5% and 10%. Compressive strength, chloride permeability, water sorptivity, and water absorption properties of concretes were obtained in this study for different testing ages up to 90 days. The influences of fly ash, metakaolin, and testing age on the properties of concretes have been identified using the analysis of variance. The statistical based regression models and the response surface method with the backward stepwise techniques were employed in the multi-objective optimization analysis. That is carried out by maximizing compressive strength while minimizing chloride permeability, water sorptivity, and water absorption. It was observed that fly ash and especially metakaolin were very effective on the aforementioned properties of the concretes, depending mainly on replacement levels and duration of curing. The results indicated that the ternary use of fly ash and metakaolin with the approximate cement replacement values of 13.3% and 10% respectively has provided the best results for the testing age of 90 days, when the optimized strength and permeability based durability properties of the concretes are concerned.     

Thixotropy and structural breakdown properties of self consolidating concrete containing various supplementary cementitious materials

In this study, thixotropy and structural breakdown of 57 self-consolidating concrete (SCC) mixtures containing various supplementary cementitious materials (SCM) were investigated by different approaches. The effects of SCM type and content on high range water reducer demand and plastic viscosity were also studied. For these purposes, various amounts of silica fume (SF), metakaolin (MK), Class F fly ash (FAF), Class C fly ash (FAC) and granulated blast-furnace slag (BFS) were utilized in binary, ternary, and quaternary cementitious blends in three water/binder (w/b) ratios. Results showed that except BFS, use of SCM in SCC mixtures increased thixotropy values in comparison with the mixtures containing only portland cement (PC). Good correlations were established between structural breakdown area and drop in apparent viscosity values for all w/b ratios. The different methods used to evaluate the thixotropy and structural breakdown got more consistent with each other as w/b decreased.     

Evaluating and forecasting the initial and final setting times of self-compacting concretes containing mineral admixtures by neural network

An experimental study was conducted to investigate the effects of using binary, ternary, and quaternary cementitious blends of portland cement (PC), fly ash (FA), ground granulated blast furnace slag (GBS), silica fume (SF), and metakaolin (MK) on initial and final setting times of self-compacting concretes (SCCs). For this purpose, a total of 65 SCC mixtures were prepared at two different water binder ratios. Furthermore, based on the experimental results, neural network (NN) model-based explicit formulations were developed to predict the initial and final setting times of SCCs in terms of the amount of concrete constituents, namely mixing water, PC, FA, GBS, SF, MK, fine (fa) and coarse (ca) aggregates, and superplasticizer (SP). The test results have revealed that the mineral admixtures were very effective on the initial and final setting times of SCCs. Besides, it was found that the model developed by using NN seemed to have a high prediction capability of initial and final setting times of SCCs.     

Effect of silica fume, steel fiber and ITZ on the strength and fracture behavior of mortar

Two sets of parameters known to affect the quality and thickness of the interfacial transition zone (ITZ), i.e. water/binder ratio and content of silica fume were varied in a series of mortars without and with steel fiber. Compressive and three-point bending tests were performed and the dissipated energies were calculated. Nanoindentation characteristics of the steel fiber–matrix and fiber–matrix-aggregate interfacial zones in the steel fiber reinforced mortars were studied. Influence of water/binder ratio, steel fiber, silica fume and ITZ on the strength and toughness of the mortar was analyzed, respectively. It is found that mortar compressive strength can be increased with low volume addition of steel fiber if the air content is well controlled; the interfacial characteristic and microstructural morphology near the fiber surface play a critical role on the three-point bending strength and the toughness of the steel fiber reinforced mortar.     

Comparison of ground waste glass with other supplementary cementitious materials

Finely ground glass has pozzolanic properties that make attractive its recycling as supplementary cementitious material. This paper compares the behaviour of waste glass powders of different fineness with that of natural pozzolana, coal fly ash and silica fume. Chemical analysis, compressive strength measurements and durability tests were carried out to investigate the effect of ground glass on strength and durability performances of mortars. Blended both with Portland cement and lime, ground glass improved strength, resistance to chloride penetration and resistance to sulphate attack of mortars more than natural pozzolana and similarly to fly ash. Mortars with ground glass immersed in water for seven years did not show any sign of degradation and increased their compressive strength. The ranking of ground glass with respect to the other mineral additions was not affected by fineness.     

The influence of supplementary cementing materials on water retaining characteristics of hydrated lime and cement mortars in masonry construction

The purpose of this paper is an investigation of the possible role of supplementary cementing materials (SCMs) on the water retaining ability of hydrated lime (CL90) and Portland cement (PC) mortars. Desorptivity (R) defines the water retaining ability of mortars in the freshly-mixed wet state. Transfer sorptivity (A) defines the ability of the substrate to withdraw water from the wet mix. The time to dewater (t _dw), is an expression derived from the sharp front theory, and enables calculation of the time taken for a wet mortar joint to be dewatered by an absorbent substrate. The results show that the very water retaining CL90 mortars become progressively more water releasing with increased volume fraction replacement levels of both ground granulated blast-furnace slag (GGBS) and fly ash (FA). On the other hand, the very water releasing PC mortars become more water retaining with the addition of silica fume (SF). Results also show that transfer sorptivity increases as the volume fraction replacement levels of GGBS and FA increases in CL90 mortars and decreases with increased volume fraction replacement levels of SF in PC mortars. Since the time taken to dewater a mortar joint (t _dw) is inversely proportional to the squared transfer sorptivity, t _dw can be dramatically altered by the addition of SCMs in both CL90 and PC mortars. These parameters have important practical consequences, not only in the initial adhesion of the mortar to the substrate but also in the strength of the set material. The ability to manipulate the water retaining properties can also allow construction time to be reduced.