Small-Signal Dynamic Analysis of Regulated Class E DC/DC Converters

Class E dc/dc converters can operate at high switching frequencies with very low switching power losses. Using commercially available power transistors and diodes, Class E converters can operate at switching frequencies in the low-MHz range, with efficiencies of about 85 percent. Previous papers dealt with the circuit parameter values needed to obtain high-efficiency operation and output-voltage regulation, and with the static control characteristics of the Class E dc/dc converter cell. The analysis is extended to include the dynamic control characteristics and further information about the static characteristics. The theoretical predictions are verified by experimental measurements on a 40-W 1.5-MHz converter.     

一种两象限零电压开关准谐振DC-DC转换器设计(英文)

传统的DC-DC转换器由电感、电容构成,通常电感和电容的面积很大,而且在开关导通和关断时的损耗严重。开关电感的两象限DC-DC转换器同时具有高功率密度和高转换效率,但是其开关导通和关断时的功率损耗仍然很严重。软开关技术可以实现开关导通和关断时的零功率损耗,从而大大减小了转换器的功率损耗。文章设计了一种新型的两象限零电压开关DC-DC转换器(ZVS-QRC),有效减小了功率损耗,并提高了功率密度和转换效率。     

Pseudo-resonant full bridge DC/DC converter

A DC-DC power converter topology that combines the ease of control and wide range of conventional DC-DC converters, with low switching losses, low dv/dt and low electromagnetic interference that is typical of zero voltage switched resonant converters is proposed. Consequently, the ratings of these components are substantially lower than for similarly rated resonant topologies. While resonant elements are used to ensure zero voltage switching of all devices, they have little or no role in the actual power transfer and can thus be reasonably sized. As the resonant elements are not involved in the primary power transfer, the converter is referred to as a pseudo-resonant converter. It is shown that the converter offers significantly higher levels of performance than either the pulse width-modulated (PWM) or typical resonant converters. Operation at very high frequencies is possible and is shown with the fabrication of a 200 W 1 MHz DC-DC converter     

Performance Comparison of Single-Stage Three-Level Resonant AC/DC Converter Topologies

In this paper, the performance of different three-level resonant converters is studied for single-stage power factor correction operation. These converters are suitable for power ranges higher than that in the currently available single-stage converters, due to their high efficiency and reduced component stresses. All the converters presented here are characterized by their ability to regulate the output voltage as well as the dc bus voltage. This leads to lower voltage stresses, wider input voltage range, higher output power applications, and improved efficiencies compared to existing single-stage topologies. Due to the availability of more degrees of freedom in the presented converters, two types of control strategies can be used for this purpose: variable frequency asymmetrical pulsewidth modulation control and variable frequency phase-shift modulation control. Three resonant converters will be studied in this paper and their performances as well as the applicability of the aforementioned control methods for each converter are compared. A 2.3-kW, 48-V converter with input voltage range of 90-265 V_rms is used to study the performance of each case.     

Improved Direct Power Control of Grid-Connected DC/AC Converters

This paper proposes new direct power control (DPC) strategies for three-phase dc/ac converters with improved dynamic response and steady-state performance. As with an electrical machine, source and converter flux, which equal the integration of the respective source and converter voltage, are used to define active and reactive power flow. Optimization of the lookup table used in conventional DPC is outlined first so as to improve power control and reduce current distortion. Then, constant switching frequency DPC is developed where the required converter voltage vector within a fixed half switching period is calculated directly from the active and reactive power errors. Detailed angle compensation due to the finite sampling frequency and the use of an integral controller to further improve the power control accuracy are described. Both simulation and experimental results are used to compare conventional DPC and vector control, and to demonstrate the effectiveness and robustness of the proposed control strategies during active and reactive power steps, and line inductance variations.      

Power electronic converters for motion control

The historical development of power electronic converters to control electrical machines is traced up to the present state of the technology. The fundamental possibilities to control average power in a switching mode are considered and the concepts switching function, converter topology and converter structure defined. A systematic approach to developing more complicated topologies and structures for singular and composite converters is discussed and application to motion control systems given. A functional classification of motion control converters is also related to the switching nature of the power processing, illustrating the fundamental dilemma of this kind of highly efficient power control. The different control possibilities of using power electronic converters with electrical machines in motion control applications (DC drives, AC drives) are reviewed systematically. The paper does not attempt to compile a comprehensive list of all possible converter circuits and variations but focusses on generic issues and technologies. The switching technology in converters and its limitations is related to snubberless, snubbed, and resonant transition-type operation, with reference also to switch drive and converter protection technology. Some future generic possibilities related to electromagnetic integration of switching converters are discussed, also in relation to a motion control application     

星载多路输出开关电源的设计

介绍一款星载多路输出开关电源。该电源的设计方法能够满足绝大部分星载多路输出开关电源的需求。重点介绍该电源的部分设计特点,分析工作原理,并给出了设计公式。实践表明,该电源优化了星载开关电源小型化设计,可广泛应用于星载多路开关电源。     

Soft switching resonant converter with duty-cycle control in DC micro-grid system

Resonant converter has been widely used for the benefits of low switching losses and high circuit efficiency. However, the wide frequency variation is the main drawback of resonant converter. This paper studies a new modular resonant converter with duty-cycle control to overcome this problem and realise the advantages of low switching losses, no reverse recovery current loss, balance input split voltages and constant frequency operation for medium voltage direct currentgrid or system network. Series full-bridge (FB) converters are used in the studied circuit in order to reduce the voltage stresses and power rating on power semiconductors. Flying capacitor is used between two FB converters to balance input split voltages. Two circuit modules are paralleled on the secondary side to lessen the current rating of rectifier diodes and the size of magnetic components. The resonant tank is operated at inductive load circuit to help power switches to be turned on at zero voltage with wide load range. The pulse-width modulation scheme is used to regulate output voltage. Experimental verifications are provided to show the performance of the proposed circuit.     

DC bus voltage control for a distributed power system

This paper addresses voltage control of distributed DC power systems. DC power systems have been discussed as a result of the introduction of renewable, small-scale power generation units. Also, telecommunication power systems featuring UPS properties might benefit from a broader introduction of DC power systems. Droop control is utilized to distribute the load between the source converters. In order to make the loading of the source converters equal, in per unit, the voltage control algorithm for each converter has to be designed to act similar. The DC side capacitor of each converter, needed for filtering, is also determined as a consequence. The root locus is investigated for varying DC bus impedance. It is found that the risk of entering converter over-modulation is a stronger limitation than stability, at least for reasonable DC bus cable parameters. The stationary and dynamic properties during load variations are also investigated.     

零电流开关大功率DC/DC双全桥变换器设计

提出了一种基于双全桥结构的单向零电流开关大功率（兆瓦级）DC/DC变换器,该变换器通过采用两个全桥变换器来实现零电流开关,实现了较低的功率损耗和输出滤波电感。为了验证提出的变换器在大功率应用中的有效性,构建了小型样机并在大功率直流电网进行了实际测试。实验证明,相比传统的两种单向大功率全桥变换器,提出变换器所需的滤波电感和半导体器件的功率损耗均较少,分别仅为1.72mH和924.5kW。     

Realization of Parasitics in Stability of DC–DC Converters Loaded by Constant Power Loads in Advanced Multiconverter Automotive Systems

Distributed DC power systems are becoming increasingly common in advanced automotive systems. Constant power load (CPL) behavior of tightly regulated DC-DC converters in multiconverter power systems is equivalent to the dynamic negative impedance, destabilizing the DC bus and, consequently, the system. Various techniques have been developed to control ideal/lossless converters loaded by CPLs. Loss components significantly enhance the stability of the cascaded converters. In this paper, the effects of parasitics in the behavior of DC-DC converters loaded by CPLs are investigated. Furthermore, the stability of power converters loaded by CPLs in parallel to conventional constant voltage loads in the presence of loss components is analyzed. Design criteria are presented for converter operation in continuous and discontinuous conduction modes, which gives recommendations on the design of multiconverter DC power systems to avoid negative impedance instability. The proposed stable operation criteria are validated with hardware prototypes and simulation analyses.     

Master–Slave Current-Sharing Control of a Parallel DC–DC Converter System Over an RF Communication Interface

Using analog wireless communication, we demonstrate a master-slave load-sharing control of a parallel dc-dc buck converter system, thereby eliminating the need for physical connection to distribute the control signal among the converter modules. The current reference for the slave modules is provided by the master module using radio-frequency (RF) transmission, thereby ensuring even sharing of the load current. The effect of delay due to RF transmission on system stability and performance is analyzed, and regions of operation for a stable as well as satisfactory performance are determined. We experimentally demonstrate a satisfactory performance of the master-slave converter at 20-kHz switching frequency under steady state as well as transient conditions in the presence of a transmission delay. The proposed control concept, which can potentially attain redundancy that is achievable using a droop method, may lead to more robust and reconfigurable control implementation of distributed converters and power systems. It may also be used as a (fault-tolerant) backup for wire-based control of parallel/distributed converters.     

DC voltage control and stability analysis of PWM-voltage-typereversible rectifiers

A PWM voltage rectifier has useful characteristics on its DC and AC sides. On its DC side, a DC-link unidirectional voltage is obtained and bidirectional power transfer capability is possible by reversing the flow direction of the DC-link current. On its AC side, near sinusoidal current waveforms and AC four-quadrant operation can be obtained, leading to high-quality power being exchanged between the power converter and the mains. The use of AC filters becomes unnecessary. The rectifier DC voltage must be regulated to a constant value. In this paper, three solutions for the DC voltage control are presented. In the first solution, the DC voltage is controlled by acting upon the quadrature component of the power converter fundamental Park's voltages with relation to the mains voltages. Slow responses are necessary because of stability reasons. Also, load power variations produce both active and reactive power variations in the power converter AC side. To improve the DC voltage response, a second control solution is presented. The power converter currents in Park's coordinates must be controlled. The DC voltage is controlled by controlling the direct Park's current component and, thus, acting only on the active power of the converter AC side. Faster responses are achieved. In this case, load power variations do not produce reactive power variations in the converter AC side. The third control solution is a simplified version of this last one. Experimental results from a 2 kVA IGBT-based prototype showing good system dynamic performance are presented     

Voltage-source active power filter based on multilevel converter and ultracapacitor DC link

A new topology for active power filters (APF) using an 81-level converter is analyzed. Each phase of the converter is composed of four three-state converters, all of them connected to the same capacitor dc link voltage and their output connected in series through output transformers. The main advantages of this kind of converter are the negligible harmonic distortion obtained and the very low switching frequency operation. The single-phase equivalent circuit is analyzed and their governing equations derived. The dc link voltage control, based on manipulating the converter's voltage phase, is analyzed together with the circuit's characteristics that determine the capability to draw or deliver active and reactive current. Simulation results for this application are compared with conventional pulsewidth-modulated (PWM) converters, showing that this filter can compensate load current harmonics, keeping better-quality sinusoidal currents from the source. The simulated configuration uses a 1-F ultracapacitor in the dc link, making it possible to store energy and deliver it during short voltage dips. This is achieved by applying a modulation control to maintain a stable ac voltage during dc voltage drops. A prototype of the filter was implemented and tested, and the obtained current waveforms showed to be as good as expected.     

Analysis and design of a new constant frequency control for QRC andMRC based on magnetic elements modification

Multiresonant power converters (MRCs) and quasi-resonant power converters (QRCs) have been modified to provide constant-frequency operation. Transformer leakage inductance has been used to adapt the traditional pulse-width-modulation (PWM) control to these converters. Conventional PWM integrated circuits can be used for the power converter regulation. Several experimental results are developed to test the control method proposed     

Switched-capacitor DC/DC converters with resonant gate drive

In this paper, we examine how switched-capacitor (SC) converters can be used in low-voltage low-power DC/DC applications with power management. Analysis of losses is presented to facilitate SC converter design and optimization. A resonant gate drive is proposed to reduce switching losses and simplify control of switches in SC converters. A closed-loop controller is designed to enable and disable oscillations of the resonant gate drive so that the output DC voltage is well regulated down to zero load and so that high efficiency is maintained for a very wide range of loads. Results are experimentally verified on two low-power (0.2 and 5 W) five-one step-down converters with regulated 3 Vdc output and efficiency greater than 80% in a 100-1 load range     

On Differential Flatness, Trajectory Planning, Observers, and Stabilization for DC–DC Converters

Differential flatness of buck, buck–boost, and boost converter models is shown. Its benefits if used for controlling the output voltage of these converters are revealed by comparing the flatness-based control with passivity-based and linear control. Two observers for the boost converter are suggested one of which requires only the measurement of the converters output voltage. Both observers can be used with minor changes for the buck–boost converter. Two flatness-based online trajectory planning algorithms are suggested. They exploit the parametrization of the trajectories in the energy. One of them is designed to achieve fast setpoint transitions during converter start-up or despite sudden load steps while simultaneously respecting the converters physical constraints. The other one is considered for applications in power factor correction. Different stabilization strategies are compared. The viability of the observers, the algorithm, and the stabilization strategies are verified by simulations of switched nonideal converter models.     

Efficiency improvement of a DC/DC converter using LTCC substrate

We propose a substrate with high thermal conductivity, manufactured by the low‐temperature co‐fired ceramic (LTCC) multilayer circuit process technology, as a new DC/DC converter platform for power electronics applications. We compare the reliability and power conversion efficiency of a converter using the LTCC substrate with the one using a conventional printed circuit board (PCB) substrate, to demonstrate the superior characteristics of the LTCC substrates. The power conversion efficiencies of the LTCC‐ and PCB‐based synchronous buck converters are 95.5% and 94.5%, respectively, while those of nonsynchronous buck converters are 92.5% and 91.3%, respectively, at an output power of 100 W. To verify the reliability of the LTCC‐based converter, two types of tests were conducted. Storage temperature tests were conducted at ?20 °C and 85 °C for 100 h each. The variation in efficiency after the tests was less than 0.3%. A working temperature test was conducted for 60 min, and the temperature of the converter was saturated at 58.2 °C without a decrease in efficiency. These results demonstrate the applicability of LTCC as a substrate for power conversion systems.     

Characterization of single-stage three-phasepower-factor-correction circuit using modular single-phase PWM DC-to-DCconverters

The complete DC characteristics of three-phase modular power-factor-correction (PFC) converters using single-phase pulsewidth modulation (PWM) DC-to-DC converter modules for high-power applications are studied. Using circuit averaging, the converter input and output quantities are determined numerically. Both the continuous and discontinuous output current modes of operation (CCM and DCM) are studied in detail. Near-unity power factor can be achieved with the converter modules operating in the DCM. An averaged model was used to study and determine the boundaries between DCM and CCM over the full period of the three-phase input voltage. It is found that high power factor is inherent in the converter system provided that the converters are operated in the DCM and the voltage conversion ratio is selected properly. The criteria for obtaining high power factor are analyzed and the optimal circuit parameters are determined to obtain the best achievable power factor. Both simulations and experimental results from a 1.5-kW prototype using full-bridge converter modules have confirmed the analysis