Synthesis and characterization of high-voltage cathode material LiNi0.5Mn1.5O4 by one-step solid-state reaction

LiNi0. 5 Mn1. 5 O4 was prepared under various conditions by one-step solid-state reaction in air and its properties were investigated by X-ray diffractormetry (XRD), scanning electron microscopy (SEM) and electrochemical measurement. XRD patterns show that LiNi0. 5 Mn1. 5 O4 synthesized under various conditions has cubic spinel structure. SEM images exhibit that the particle size increases with increasing calcination temperature and time. Electro chemical test shows that the LiNi0. 5 Mn1.5 O4 calcined at 700 ℃ for 24 h delivers up to 143 mA · h/g, and the capacity retains 132 mA · h/g after 30 cycles.     

球形LiMn1.5Ni0.5O4材料的嵌脱动力学

为明晰Li Mn1.5Ni0.5O4正极材料的动力学性能,采用水热辅助共沉淀法合成了尖晶石Li Mn1.5Ni0.5O4正极材料,并采用扫描电镜(SEM)、X射线粉末衍射(XRD)和电化学阻抗(EIS)研究了材料的结构和锂离子嵌脱动力学.实验结果表明:共沉淀法制备的Li Ni0.5Mn1.5O4材料颗粒呈均匀球形,且平均粒径较小,粒度分布较窄.在循环过程中,Li Ni0.5Mn1.5O4的电荷转移电阻增大,锂离子扩散系数减小,进而电子电导率和离子电导率下降.温度升高后,Li Ni0.5Mn1.5O4材料的溶液电阻变化不大,但是电荷转移电阻逐渐增大,锂离子扩散系数逐渐减小;此外,随着温度的升高,Li Ni0.5Mn1.5O4材料的溶解速度加快,从而导致SEI膜的厚度增大.Li Ni0.5Mn1.5O4材料的嵌脱锂动力学与温度和循环次数有密切关系.     

Characteristics of LiCoO2, LiMn2O4 and LiNi0.45Co0.1Mn0.45O2 as cathodes of lithium ion batteries

LiNi_0.45Co_0.10Mn_0.45O₂ was synthesized from Li₂CO₃ and a triple oxide of nickel, cobalt and manganese at 950 °C in air. The structures and characteristics of LiNi_0.45Co_0.10Mn_0.45O₂, LiCoO₂ and LiMn₂O₄ were investigated by XRD, SEM and electrochemical measurements. The results show that LiNi_0.45Co_0.10Mn_0.45O₂ has a layered structure with hexagonal lattice. The commercial LiCoO₂ has sphere-like appearance and smooth surfaces, while the LiMn₂O₄ and LiNi_0.45Co_0.10Mn_0.45O₂ consist of cornered and uneven particles. LiNi_0.45Co_0.10Mn_0.45O₂ has a large discharge capacity of 140.9 mA · h/g in practical lithium ion battery, which is 33.4% and 2.8% above that of LiMn₂O₄ and LiCoO₂, respectively. LiCoO₂ and LiMn₂O₄ have higher discharge voltage and better rate-capability than LiNi_0.45Co_0.10Mn_0.45O₂. All the three cathodes have excellent cycling performance with capacity retention of above 89.3% at the 250th cycle. Batteries with LiMn₂O₄ or LiNi_0.45Co_0.10Mn_0.45O₂ cathodes show better safety performance under abusive conditions than those with LiCoO₂ cathodes. Foundation item: Project(50302016) supported by the National Natural Science Foundation of China; Project(2005037698) supported by the Postdoctoral Science Foundation of China     

Structure and electrochemical properties of La, F dual-doped iLa0.01Mn1.99O3.99F0.01 cathode materials

The cathode materials LiMn₂O₄ and rare earth elements La-doped or La and F dual-doped spinel lithium manganese oxides were synthesized by the citric acid-assisted sol-gel method. The synthesized samples were investigated by differential thermal analysis (DTA) and thermogravimetry (TG) measurements, X-ray diffraction (XRD), scanning electronic microscope (SEM), cyclic voltammetry (CV), and charge-discharge test. XRD data shows that all the samples exhibit the same pure spinel phase, and the LiLa_0.01Mn_1.99O_3.99F_0.01 and LiLa_0.01Mn_1.99O₄ samples have smaller lattice parameters and unit cell volume than LiMn₂O₄. SEM indicates that LiLa_0.01Mn_1.99O_3.99F_0.01 has a slightly smaller particle size and a more regular morphology structure with narrow size distribution. The charge-discharge test reveals that the initial capacities of LiMn₂O₄, LiLa_0.01Mn_1.99O₄, and LiLa_0.01Mn_1.99O_3.99F_0.01 are 129.9, 122.8, and 126.4 mAh·g⁻¹, and the capacity losses of the initial values after 50 cycles are 14.5%, 7.6%, and 8.0%, respectively. The CVs show that the La and F dual-doped spinel displays a better reversibility than LiMn₂O₄.     

Synthesis and characterization of Mg3(PO4)2-coated Li1.05Ni1/3Mn1/3Co1/3O2 cathode material for Li-ion battery

Mg₃(PO₄)₂-coated Li_1.05Ni_1/3Mn_1/3Co_1/3O₂ cathode materials were synthesized via co-precipitation method. The morphology, structure, electrochemical performance and thermal stability were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS), charge/discharge cycling and differential scanning calorimeter (DSC). SEM analysis shows that Mg₃(PO₄)₂-coating changes the morphologies of their particles and increases the grains size. XRD and CV results show that Mg₃(PO₄)₂-coating powder is homogeneous and has better layered structure than the bare one. Mg₃(PO₄)₂-coating improved high rate discharge capacity and cycle-life performance. The reason why the cycling performance of Mg₃(PO₄)₂-coated sample at 55 °C was better than that of room temperature was the increasing of lithium-ion diffusion rate and charge transfer rate with temperature rising. Mg₃(PO₄)₂-coating improved the cathode thermal stability, and the result was consistent with thermal abuse tests using Li-ion cells: the Mg₃(PO₄)₂ coated Li_1.05Ni_1/3Mn_1/3Co_1/3O₂ cathode did not exhibit thermal runaway with smoke and explosion, in contrast to the cells containing the bare Li_1.05Ni_1/3Mn_1/3Co_1/3O₂. Funded by the National Natural Science Foundation of China (No. 20273047)     

Electrochemical properties of spinel LiMn2O4 and LiAl0.1Mn1.9O3.9F0.1 synthesized by solid-state reaction

Two types of spinel cathode powders, LiMn2O4 and LiAl0.1Mn1.9O3.9F0.1, were synthesized by solid-state reaction. X-ray diffraction (XRD) patterns of the prepared samples were identified as the spinel structure with a space group of Fd 3 m. The cubic lattice parameter was determined from least-squares fitting of the XRD data. The LiAl0.1Mn1.9O3.9F0.1 sample showed a little lower initial capacity, but better cycling performance than the LiMn2O4 sample at both room temperature and an elevated temperature. The Vanderbilt method was used to test the electrochemical conductivity of the LiMn2O4 samples. The electrochemical impedance spec-troscopy (EIS) method was employed to investigate the electrochemical properties of these spinel LiMn2O4 samples.     

Influence on performance and structure of spinel LiMn2O4 for lithium-ion batteries by doping rare-earth Sm

The spinel LiMn₂O₄ used as cathode materials for lithium-ion batteries was synthesized by mechano-chemistry fluid activation process, and modified by doping rare-earth Sm. Thesting of X-ray diffraction, cyclic voltammograms, charge-discharge and SEM was carried out for LiMn₂O₄ cathode materials and the modified materials. The results show that the cathode materials doped rare earth Li _x Mn_2−y Sm _z O₄ (0.95⩽x⩽1.2, 0⩽y⩽0.3, 0⩽z⩽0.2) exhibit standard spinel structure, high reversibility of electrochemistry and excellent properties of charge-discharge. In EC: DMC(1 : 1)+1 mol/L LiPF₆ electrolyte with discharge capacity more than 130 mA · h/g, and its capacity is deteriorated less than 15% after 300 cycles at room temperature and less than 20% after 200 cycles at 55°C. At the same time, Crystal Field Theory was applied to explain the function and mechanism of doped rare earth element. Foundation item: Project (02JJY2081) supported by the Natural Science Foundation of Hunan Province     

Synthesis and characterization of triclinic structural LiVPO4F as possible 4.2 V cathode materials for lithium ion batteries

A potential 4.2 V cathode material LiVPO4F for lithium batteries was prepared by two-step reaction method based on a carbon-thermal reduction （CTR） process. Firstly, V2O5, NH4H2PO4 and acetylene black are reacted under an Ar atmosphere to yield VPO4. The transition-metal reduction is facilitated by the CTR based on C→CO transition. These CTR conditions favor stabilization of the vanadium as V^3＋ as well as leaving residual carbon, which is useful in the subsequent electrode processing. Secondly, VPO4 reacts with ElF to yield LiVPO4F product. The property of the LiVPO4F was investigated by X-ray diffractometry （XRD）, scanning electron microscopy （SEM） and electrochemical measurement. XRD studies show that LiVPO4F synthesized has triclinic structure（space group p I ）, isostructural with the naturally occurring mineral tavorite, EiFePO4-OH. SEM image exhibits that the particle size is about 2μm together with homogenous distribution. Electrochemical test shows that the initial discharge capacity of LiVPO4F powder is 119 mA·h/g at the rate of 0.2C with an average discharge voltage of 4.2V （vs Ei/Li^＋）, and the capacity retains 89 mA·h/g after 30 cycles.     

Al_2O_3包覆对富锂锰基正极材料Li_(1.2)Mn_(0.54)Co_(0.13)Ni_(0.13)O_2的电化学性能影响

采用水热法合成富锂三元正极材料,探究了最佳包覆比例下Al_2O_3包覆对材料的电化学性能影响.采用扫描电镜(SEM)和X射线衍射仪(XRD)表征了富锂三元正极材料的表面形貌和结构,通过循环伏安(CV)、交流阻抗(EIS)技术分析了材料电化学性的影响因素.结果表明,通过异丙醇铝水解制得了氧化铝包覆层,提高了材料的比容量,稳定了材料的结构.     

Modification of LiCo1/3Ni1/3Mn1/3O2 cathode material by CeO2-coating

LiCo_1/3Ni_1/3Mn_1/3O₂ was coated by a layer of 1.0 wt% CeO₂ via sol-gel method. The bared and coated LiMn_1/3Co_1/3Ni_1/3O₂ was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammogram (CV) and galvanotactic charge-discharge test. The results show that the coating layer has no effect on the crystal structure, only coating on the surface; the 1.0 wt% CeO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ exhibits better discharge capacity and cycling performance than the bared LiCo_1/3Ni_1/3Mn_1/3O₂. The discharge capacity of 1.0 wt% CeO₂-coated cathode is 182.5 mAh·g⁻¹ at a current density of 20 mA·g⁻¹, in contrast to 165.8 mAh·g⁻¹of the bared sample. The discharge capacity retention of 1.0 wt% CeO₂-coated sample after 12 cycles reaches 93.2%, in comparison with 86.6% of the bared sample. CV results show that the CeO₂ coating could suppress phase transitions and prevent the surface of cathode material from direct contact with the electrolyte, thus enhance the electrochemical performance of the coated material.     

Synthesis of Li2Fe0.9Mn0.1SiO4/C composites using glucose as carbon source

Li2Fe0.9Mn0.1SiO4/C composites were synthesized by using glucose as carbon source. The samples were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM) and electrochemical measurements. All Li2Fe0.9Mn0.1SiO4/C composites are of the similar crystal structure. With increasing the carbon content in the range of 5%-20% (mass fraction), the diffraction peaks in XRD patterns broaden and the particle sizes and the tap density of samples decrease. The Li2Fe0.9Mn0.1SiO4/C composites with carbon content of 14.12% show excellent the capacity retention remains 92.2% after 30 cycles.     

Preparation of LiFePO4 for lithium ion battery using Fe2P2O7 as precursor

In order to obtain a new precursor for LiFePO4, Fe2P2O7 with high purity was prepared through solid phase reaction at 650 ℃ using starting materials of FeC2O4 and NH4H2PO4 in an argon atmosphere. Using the as-prepared Fe2P2O7, Li2CO3 and glucose as raw materials, pure LiFePO4 and LiFePO4/C composite materials were respectively synthesized by solid state reaction at 700 ℃ in an argon atmosphere. X-ray diffractometry and scanning electron microscopy（SEM） were employed to characterize the as-prepared Fe2P2O7, LiFePO4 and LiFePO4/C. The as-prepared Fe2P2O7 crystallizes in the Cl space group and belongs to β-Fe2P2O7 for crystal phase. The particle size distribution of Fe2P2O7 observed by SEM is 0.4-3.0 μm. During the Li^＋ ion chemical intercalation, radical P2O7^4- is disrupted into two PO4^3- ions in the presence of O^2-, thus providing a feasible technique to dispose this poor dissolvable pyrophosphate. LiFePO4/C composite exhibits initial charge and discharge capacities of 154 and 132 mA·h/g, respectively.     

水热法制备LiNi_(0.5)Mn_(1.5)O_4及其电化学性能的研究

以LiOH·H2O、MnSO4·H2O和NiSO4·6H2O等为原料,采用水热法合成尖晶石LiNi0.5Mn1.5O4材料.利用扫描电子显微镜、粉末X-射线衍射仪、电化学测试分别对材料形貌、结构和电化学性能进行表征.研究加入不同锂量和热处理对尖晶石LiNi0.5Mn1.5O4材料的初始容量、放电平台以及循环性能的影响.结果表明:经过850℃热处理所合成的材料分布均匀、结晶和电化学性能良好.当LiOH溶液为0.162 g·mL-1时,尖晶石LiNi0.5Mn1.5O4材料在1 C倍率电流(140 mAh g-1)条件下,首次放电比容量为111.0 mAh·g-1.且该样品的循环性能优越:经150充放电循环后的容量衰减率仅为4.5%.     

Preparation and electrochemical performance of Li2Mn0.5Fe0.5SiO4 cathode material with sol-gel method for lithium ion batteries

Li2Fe0.5Mn0.5SiO4 material was synthesized by a citric acid-assisted sol-gel method. The influence of the stoichiometric ratio value of n（citric acid） to n（Fe2＋-Mn2＋） on the electrochemical properties of Li2Fe0.5Mn0.5SiO4 was studied. The final sample was identified as Li2Fe0.5Mn0.5SiO4 with a Pmn21 monoclinic structure by X-ray diffraction analysis. The crystal phases components and crystal phase structure of the Li2Fe0.5Mn0.4SiO4 material were improved as the increase of the stoichiometric ratio value of n（citric acid） to n（Fe2＋-Mn2＋）. Field-emission scanning electron microscopy verified that the Li2Fe0.5Mn0.5SiO4 particles are agglomerates of Li2Fe0.5Mn0.5SiO4 primary particles with a geometric mean diameter of 220 nm. The Li2Fe0.5Mn0.5SiO4 sample was used as an electrode material for rechargeable lithium ion batteries, and the electrochemical measurements were carried out at room temperature. The Li2Fe0.5Mn0.5SiO4 electrode delivered a first discharge capacity of 230.1 mAh/g at the current density of 10 mA/g in first cycle and about 162 mAh/g after 20 cycles at the current density of 20 mA/g.     

基于双金属MOFs 制备Co3O4/In2O3 复合物及其气敏性能的研究

以硝酸铟(In(NO₃)₃·xH₂O)、对苯二甲酸(H₂BDC)、六水合硝酸钴(Co(NO₃)· 6H₂O) 为原料, 首先采用一锅油浴法合成了含有Co²⁺ 的铟基金属有机框架材料(MOFs) Co²⁺/CPP-3(In) 材料, 然后在450 ℃ 下焙烧制备Co₃O₄/In₂O₃ 复合物气敏材料, 将Co₃O₄/In₂O₃ 复合物的粉体制作成传感器, 并对其气敏性能进行研究。利用扫描电子显微镜和X 射线衍射仪(XRD) 对双金属MOFs Co²⁺/CPP-3(In) 材料和Co₃O₄/In₂O₃ 复合物进行表征, 采用静态配气法测试其气敏性能。结果表明, Co₃O₄/In₂O₃(n_Co : n_In = 0.4 : 1) 样品的形貌保留了其MOFs 前驱体的棒状结构, 棱柱形框架更为突出, 表面呈凹陷状, 棒体中间粗两边细, 六角截面和棒体均布满了孔洞。结合EDX 和XRD 表征结果, Co²⁺/CPP-3(In) MOFs 前驱体完全转化成Co₃O₄/In₂O₃ 复合物; Co₃O₄/In₂O₃(n_Co : n_In = 0.4 : 1) 复合物在 70 ℃ 下对5×10^-6 H₂S 的气敏性能最优, 响应值达到153, 是同条件下纯备In₂O₃对H₂S 响应值的5 倍, 并且有较好的重复性、选择性和稳定性。     

锂离子电池正极材料LiFePO4的合成及其改性

采用共沉淀法合成了锂离子正极材料LiFePO4,考察了不同合成条件对材料结构及性能的影响.研究结果表明:通过碳包覆改性后,LiFePO4的容量可明显提高,SiO2的掺杂对LiFePO4的结构没有影响.同时讨论了上述两种改性方法对材料性能的影响机制.     

Kinetics of Fe3O4 formation by air oxidation

The kinetics of Fe₃O₄ formation by air oxidation of slightly acidic suspension of Fe(OH)₂ was studied. The effects of initial concentration of Fe(II), temperature, partial pressure of oxygen, air flow rate and stirring rate on the oxidation rate were investigated. The results show that Fe₃O₄ formation is composed of two-step reaction, the first step is the formation of Fe(OH) ₂ ⁺ by oxidation of Fe(OH)⁺ complex ions, the second step is the formation of magnetite by dehydration and deprotonation of Fe(OH)⁺ and Fe(OH) ₂ ⁺ . The oxidation reaction is zero-order with respect to the concentration of Fe(II) and around 0.5-order with respect to partial pressure of oxygen, and oxygen transfer process is rate-limiting step of oxidation reaction with apparent activation energy of 2.74 kJ · mol⁻¹.     

双层碳包覆Li4Ti5O12的合成和电化学性能研究

采用固相合成方法制备了双层碳包覆Li_4Ti_5O_(12)复合材料.通过X射线衍射、扫描电子显微镜、循环伏安、电化学阻抗和恒流充放电分析等测试,研究了产物的结构、形貌及电化学性能.结果表明:通过碳包覆改性后,Li_4Ti_5O_(12)的容量可明显提高,碳的包覆对Li_4Ti_5O_(12)的结构没有影响;2 C倍率下首次放电比容量为118.8 mAh/g,300次循环后放电比容量仍为108.5 mAh/g,容量保持率为91.3%,具有非常好的电化学性能.     

Effect of baking processes on properties of TiB2/C composite cathode material

Pitch and TiB₂/C green composite cathode material were respectively analyzed with simultaneous DSC-TGA, and effects of three baking processes of TiB₂/C composite cathode material, i.e. K25, K5 and M5, on properties of TiB₂/C composite cathode material were investigated. The results show that thermogravimetric behavior of pitch and TiB₂/C green composite cathode is similar, and appears the largest mass loss rate in the temperature range from 200 to 600°C. The bulk density variation of sample K5 before and after baking is the largest (11.9%), that of sample K25 is the second, and that of sample M5 is the smallest (6.7%). The crushing strength of sample M5 is the biggest (51.2 MPa), that of sample K25 is the next, and that of sample K5 is the smallest (32.8 MPa). But, the orders of the electrical resistivity and electrolysis expansion of samples are just opposite with the order of crushing strength. The heating rate has a great impact on the microstructure of sample. The faster the heating rate is, the bigger the pore size and porosity of sample are. Compared with the heating rate between 200 and 600° of samples K25 and K5, that of sample M5 is slower and suitable for baking process of TiB₂/C composite cathode material. Foundation item: Project (2005CB623703) supported by the Major State Basic Research and Development Program of China; Project (2008AA030502) supported by the National High-Tech Research and Development Program of China     

Effect of sintering time on the electrochemical properties of spinel LiMn2O4 synthesized by solid-state reaction

LiMn2O4 powder as a cathode materials for rechargeable lithium-ion batteries was prepared by solid-state reaction from LitCO3 and electrolytic MnOz at different sintering periods （2, 6, 18, and 32 h）. X-ray diffraction （XRD） patterns of the prepared samples are identified as the spinel structure with a space group of Fd3 m. The lattice parameters almost remain the same as the sintering periods increase. The sample with a sintering period of 32 h shows good cycling performance at both low and nigh current densities, and also elevated temperature. It is believed that the excellent electrochemical behavior of this sample results from its good crystallinity and large grain size compared with other samples. Different electrochemical measurements were conducted to investigate the electrochemical properties of spinel LiMn204. 2008 University of Science and Technology Beijing. All rights reserved.