首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
Hybrid nanocomposites were prepared via solution blending of octaphenethyl POSS into novolac resin. The resulted hybrid blends were investigated by Fourier-transformed infrared spectra (FTIR), polarized optical microscopy (POM), wide X-ray diffraction and differential scanning calorimetry (DSC). FTIR results showed that there existed intermolecular hydrogen bond between the hydroxyl groups of the phenolic resin and POSS siloxane groups, which could promote POSS to disperse well in the polymer matrix up to 20 wt% POSS loading. At higher POSS loading, POSS would aggregate and lead to macrophase separation, which was demonstrated by POM, DSC and WXRD. Finally, hexamethylene tetramine was used to cure the novolac blends to form hybrid network phenolic nanocomposites. Dynamic mechanical analysis results showed that the storage modulus of the hybrid networks was improved up to 20 wt% POSS loading; the T g was increased with increasing POSS content and higher than that of the control phenolic resin except that 5 wt% POSS loading. Thermo gravimetric analysis showed that the thermal stability of hybrid networks was also enhanced with the incorporation of POSS.  相似文献   

2.
The influence of blend composition on crystallization behavior of a typical crystalline/crystalline blend, polyoxymethylene (POM)/poly(ethylene oxide) (PEO), during slow non-isothermal crystallization was investigated by polarized light microscope (PLM) connected with a THMS600 hot-stage, scanning electron microscope (SEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The experimental results indicated that with increasing PEO content in the blend, the crystallization temperature of POM of the blends reduced and the multiple crystalline morphologies or structures including two kinds of interfibrillar or interlamellar structures were produced. The melting point of each component decreased with raising the content of the other constituent due to the inclusion and entanglement between POM and PEO molecules. The shoulder melting peak of POM appeared in DSC heating traces of the PEO-rich blend because the stronger inclusion and entanglement induced the imperfect crystallization of POM.  相似文献   

3.
Structural behavior of miktoarm star polymers comprising poly(butyl acrylate) (PBA) and poly(ethylene oxide) (PEO) arms was studied by means of Differential Scanning Calorimetry (DSC), Wide Angle X-Ray Scattering (WAXS), Polarized Optical Microscopy (POM) and Fourier Transform Infrared Spectroscopy (FTIR) methods. The aim of this study was to correlate changes in the composition of the arms of the PBA/PEO miktoarm star polymers with their structures. As a consequence of increasing PBA content, the decrease in crystallinity of the studied PBA/PEO heteroarm star copolymers was observed. Regardless of the copolymer composition, fraction of oxyethylene units in the crystalline PEO phase was similar in all investigated systems. The POM images showed spherulitic morphology of the materials having low PBA content, while an increase in PBA arms fraction leads to the formation of less ordered structures. The analysis of FTIR vibrational spectrum indicates helical conformation of PEO chains in the crystalline phase. Isothermal crystallization studies carried out using the FTIR technique suggest the existence of isolated domains in the nanoscopic scale of investigated materials.  相似文献   

4.
双酚A型双邻苯二甲腈(BAPh)与酚醛树脂(novolac)通过熔融共混形成了预聚物(BAPh/novolac),经后续热处理制备了BAPh/novolac固化物。通过DSC,FTIR,TGA及流变性能测试研究了该共混体系的固化反应特性,固化物的热稳定性和热氧化稳定性。结果表明:该共混体系可以在无外加固化剂的条件下进行固化反应,固化物的玻璃化转变温度(Tg)达241℃。其固化物在空气和N2气氛中的起始分解温度为380~449℃,且在氮气下800℃残炭率达71%,表现出良好的热稳定性和热氧稳定性。  相似文献   

5.
Han LüSixun Zheng 《Polymer》2003,44(16):4689-4698
Thermosetting polymer blends composed of polybenzoxazine (PBA-a) and poly(ethylene oxide) (PEO) were prepared via in situ curing reaction of benzoxazine (BA-a) in the presence of PEO, which started from the initially homogeneous mixtures of BA-a and PEO. Before curing, the BA-a/PEO blends displayed the single and composition-dependant glass transition temperatures (Tg's) in the entire blend composition, and the equilibrium melting point depression was also observed in the blends. It is judged that the BA-a/PEO blends are completely miscible. The miscibility was mainly ascribed to the contribution of entropy to mixing free energy since the molecular weight of BA-a is rather low. However, phase separation occurred after curing reaction at the elevated temperature, which was confirmed by differential scanning calorimetry (DSC) and scanning electronic microscopy (SEM). It was expected that the PBA-a/PEO blends would be miscible since PBA-a possesses a great number of phenolic hydroxyls in the molecular backbone, which are potential to form the intermolecular hydrogen bonding interactions with oxygen atoms of PEO and thus would fulfill the miscibility of the blends. To interpret the experimental results, we investigated the variable temperature Fourier transform infrared spectroscopy (FTIR) of the blends via model compound. The FTIR results indicate that the phenolic hydroxyl groups could not form the efficient intermolecular hydrogen bonding interactions at the elevated temperatures (e.g. the curing temperatures), i.e. the phenolic hydroxyl groups existed mainly in the non-associated form in the system. Therefore, the decrease of the mixing entropy still dominates the phase behavior of thermosetting blends at the elevated temperature.  相似文献   

6.
含异氰酸酯基的低聚物和聚醚增容改性POM/TPU共混物   总被引:2,自引:0,他引:2       下载免费PDF全文
刘春林  周如东  吴盾  陈玲红 《化工学报》2008,59(9):2377-2383
利用双螺杆挤出机制备了聚甲醛(POM)/热塑性聚氨酯弹性体(TPU)、POM/TPU/含异氰酸酯基的低聚物(Z)以及POM/TPU/Z/聚醚3种共混物。采用力学性能测试、差示扫描量热分析(DSC)、偏光显微镜(PLM)、傅里叶转换红外线光谱 (FTIR)、扫描电子显微镜(SEM)、动态力学性能分析(DMA)等,研究了3种共混物的力学性能、结晶行为及形态结构。结果表明:共混物的缺口冲击强度和断裂伸长率随TPU含量的增加而提高;异氰酸酯基低聚物(Z)和聚醚在促进分散相分散、增强两相间的相容性方面发挥重要作用,降低了聚甲醛的结晶度,能够有效地提高共混物的缺口冲击强度和断裂伸长率。  相似文献   

7.
Miscibility and crystallization behavior of a polymer blend consisting of two crystalline components, polyoxymethylene copolymer (Co‐POM) and poly(ethylene oxide) (PEO), have been investigated. Experimental results indicate that Co‐POM is thermodynamically miscible with PEO, as shown by the existence of single‐composition dependent glass transition temperature over the entire composition range. The crystal structures and spherulitic morphologies of (Co‐POM)/PEO blends were studied by X‐ray diffraction, differential scanning calorimetry, scanning electron microscopy, and polarizing light microscopy. It was found that the PEO spherulites crystallized within the matrix of the crystals of the pre‐existing Co‐POM phase and resulted in a high extent of interfibrillar segregation. The unique interpenetrated crystalline structure was beneficial for the sufficient contact between the two components and significantly improved both the toughing and the lubricating effect of PEO on the POM matrix. On incorporation of 30 wt% PEO, the notched impact strength of POM was enhanced from 6.7 to 10.3 MPa, by about 53.7%, while the elongation at break increased from 28.5% to 121.0%, by about 3.2 times. Furthermore, the friction coefficient drastically decreased from 0.35 to 0.17, demonstrating the enhanced tribological performance of the miscible blends. J. VINYL ADDIT. TECHNOL., 22:479–486, 2016. © 2015 Society of Plastics Engineers  相似文献   

8.
A poly(ethylene oxide) (PEO) novolac‐type phenolic resin blend was prepared by the physical blending method. The modified novolac‐type phenolic resin with various PEO contents was used as a matrix precursor to fabricate carbon/carbon composites. The effect of the PEO/phenolic resin mixing ratio on the change of the density and of the porosity was studied. The flexural strength and interlaminar shear strength of the PEO/phenolic resin blend‐derived carbon/carbon composites were also investigated. The results show that the density of the PEO/phenolic resin blend‐derived carbon/carbon composites decreases with the PEO content. The X‐ray diffraction and Raman spectra studies showed that the carbon fiber in the samples will affect the growth of the ordered carbon structure. From SEM morphological observation, it is shown that the fracture surface of specimens is smooth. Also, there is less fiber pull‐out and fiber breakage on the fracture surface. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1609–1619, 2002; DOI 10.1002/app.10407  相似文献   

9.
Phenolic resin/poly(dimethylsiloxane adipamide) (PDMSA) blends, which have been prepared, show miscibility due to intermolecular H‐bonding existing between phenolic resin and the PDMSA. The specific H‐bonding of novolac type phenolic/PDMSA blends was characterized by means of glass transition temperature behavior and Fourier Transform Infrared Spectroscopy (FTIR). The strength of intermolecular H‐bonding within the phenolic blend is a function of the H‐bonded group of the PDMSA modifier and corresponds to the deviation glass transition temperature (ΔTg). Phenolic/PDMSA blends were completely miscible, as confirmed by the Tg study. The FTIR result is in good agreement with the inference from Tg behavior. The char yield of phenolic/PDMSA corresponds to the phenolic resin content. The molecular mobility of phenolic/PDMSA blends increases with PDMSA content in the phenolic‐rich region. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 984–992, 2002  相似文献   

10.
Solid solutions of blends of poly(ethylene oxide) (PEO) and epoxidized natural rubber (ENR) comprising 12 wt % of LiClO4 were studied. Two glass transition temperatures, corresponding to the Tgs of the constituents, confirm immiscibility of the polymers over the entire composition range. It turns out that the Tgs of both polymers slightly increase after addition of salt to the blends. This shift is approximately constant over the whole range of blend composition. Accordingly, Tg measurements reveal that the salt dissolves to approximately equal relative amounts in the two phases. The degree of crystallinity of PEO in blends with ENR descends only to a minor extent with ENR content. However, addition of salt leads first to decreasing crystallinity and second this decrease becomes more pronounced with the addition of ENR. It shows that under these experimental conditions the salt content in PEO increases as compared to ENR. As one expects, the rate of isothermal crystallization does not change in blends as long as PEO is in excess. The situation changes again when salt is added. The rate decreases in a certain range of crystallization temperatures when ENR is added, demonstrating that salt is favorably dissolved in PEO. Conductivity was measured in polymers comprising different salt concentrations. A power‐law dependence of conductivity on salt concentration was found. It results that the mobility of charge carriers in PEO exceeds that of ENR by five orders of magnitude. Therefore, the conductivity in blends is primarily governed by PEO as long as PEO is in excess. Conductivity measurements reveal again that salt is preferably dissolved in PEO. The distribution coefficient is estimated. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008  相似文献   

11.
Blends of poly(ethylene oxide) (PEO) with poly(ε-caprolactone) (PCL), both semicrystalline polymers, were prepared by co-dissolving the two polyesters in chloroform and casting the mixture. Phase contrast microscopy was used to probe the miscibility of PEOB/PCL blends. Experimental results indicated that PEO was immiscible with PCL because the melt was biphasic. Crystallization of PEO/PCL blends was studied by differential scanning calorimetry and analyzed by the Avrami equation. The crystallization rate of PEO decreased with the increase of PCL in the blends while the crystallization mechanism did not change. In the case of the isothermal crystallization of PCL, the crystallization mechanism did not change, and the change in the crystallization rate was not very big, or almost constant with the addition of PEO, compared with the change of the crystallization rate of PEO.  相似文献   

12.
制备了一系列聚甲醛/超高相对分子质量聚乙烯(POM/PE-UHMW)共混物,并通过力学性能测试,差示扫描量热仪及扫描电子显微镜等分析了共混物的结构和性能,分别采用Avrami以及莫志深理论对POM及POM/PE-UHMW(100/1)非等温结晶动力学进行了理论分析,利用Kissinger方法对其结晶活化能进行了计算。结果表明,当PE-UHMW含量为1 %(质量分数,下同)时,共混物的缺口冲击强度达到最大值,较纯POM提高了约24.3 %;同时其降低了POM的结晶速率和结晶活化能,但相对结晶度稍有提高。  相似文献   

13.
Blends of poly(ethylene oxide) (PEO) and resole type phenolic resin were prepared by a solution cast method using water as a solvent. The cured blends were made by heat curing without using any catalyst. The blends were characterized by dynamic mechanical analysis (DMA), which indicated that PEO forms compatible blend with the resole. The glass transition values, read from the DMA traces, showed a positive shift as compared to the theoretical values calculated by the Fox equation. This suggests a strong H‐bonding interaction between the phenolic resole and PEO as established by Fourier transformed infrared spectroscopy. Flexural test indicated an enhanced flexibility of the blends when compared to the neat phenolic resin. The fracture surface analysis by using a scanning electron microscope (SEM) revealed an increase in plastic deformation with increasing PEO concentration in the blend. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013  相似文献   

14.
This article is the first study on the microinjection molding and the effects of the microprocessing parameters on the crystallization and orientation of polyoxymethylene/poly(ethylene oxide) (POM/PEO) blend, which has better toughness and self‐lubricity compared with the neat POM and therefore is a better candidate material for making microparts like microgears with higher performances. The crystalline and phase morphologies were investigated by polarized light microscope (PLM), differential scanning calorimeter (DSC) and scanning electron microscope (SEM). The crystalline orientation of the microparts was evaluated by two‐dimensional wide‐angle X‐ray diffraction (2D‐WAXD) and Herman's orientation function. The experimental results showed that both POM and POM/PEO microparts prepared by microinjection molding exhibited three distinct layers, i.e., skin layer, shear layer and core layer, while the latter had thicker shear layer but thinner skin layer and core layer. PEO was well dispersed in POM matrix. The spherulite size, the melting point as well as the crystallinity of POM in the POM/PEO blend decreased due to the interference of PEO in the crystallization of POM. A shish‐kebab structure was observed in the shear layers of the POM/PEO microparts. The effects of processing parameters on the thicknesses of different layers of the POM/PEO microparts were investigated. With increase of the injection speed or decrease of the mold temperature, the skin layer and the core layer became thicker, while the shear layer and the oriented region became thinner. However, the influence of the injection pressure was not obvious. Also, the processing parameters affected the crystalline orientation of the POM/PEO microparts. With increase of the injection speed or decrease of the mold temperature, the orientation function f decreased, indicating a lower degree of orientation. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40538.  相似文献   

15.
Incompatibility of poly(lactic acid)/poly(?‐caprolactone) (PLA/PCL) (80:20) and (70:30) blends were modified by incorporation of a small amount of polyoxymethylene (POM) (≤3 phr). Impact of POM on microstructures and tensile property of the blends were investigated. It is found that the introduction of POM into the PLA/PCL blends significantly improves their tensile property. With increasing POM loading from zero to 3 phr, elongation at break increases from 93.2% for the PLA/PCL (70:30) sample to 334.8% for the PLA/PCL/POM (70:30:3) sample. A size reduction in PCL domains and reinforcement in interfacial adhesion with increasing POM loading are confirmed by SEM observations. The compatibilization effect of POM on PLA/PCL blends can be attributed to hydrogen bonding between methylene groups of POM and carbonyl groups of PLA and PCL. In addition, nonisothermal and isothermal crystallization behaviors of PLA/PCL/POM (70:30:x) samples were investigated by using differential scanning calorimetry and wide angle X‐ray diffraction measurements. The results indicate that the crystallization dynamic of PLA matrix increases with POM loadings. It can be attributed to the fact that POM crystals have a nucleating effect on PLA. While crystallization temperature is 100 °C, crystallization half‐time can reduce from 9.4 to 2.0 min with increasing POM loading from zero to 3 phr. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46536.  相似文献   

16.
The miscibility and thermal degradation of poly(ethylene glycol) (PEG)‐toughened novolac‐type phenolic resin were investigated. Differential scanning calorimetry (DSC) results confirmed that the phenolic resin/PEG blend was blended completely. Infrared spectra show that hydrogen bonding existed in the blends. Thermal degradation of PEG blended with novolac‐type phenolic resin was studied utilizing a dynamic thermogravimetric technique in a flowing nitrogen atmosphere at several heating rates (i.e., 5, 10, 20, 40°C/min). Thermal degradation of phenolic resin/PEG blends takes place in multiple steps. The thermal behavior and the thermal stability affected the thermal degradation, which coincided with the data from the thermal degradation of novolac‐type phenolic resin/PEG blends by thermogravimetric analysis (TGA). © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 188–196, 2001  相似文献   

17.
The dispersion of multi-walled carbon nanotubes (MWNTs) in crystalline poly(ethylene oxide) (PEO) is significantly improved by grafting with poly(methyl methacrylate) (PMMA) on surface of MWNTs via emulsion reactions. The synthesized MWNTs-g-PMMA is soluble in solvents that can dissolve PMMA and is well dispersed in PEO. The effects of the MWNTs-g-PMMA on PEO crystallization and its use as a reinforcement for PEO are investigated using DMA, DSC, POM, and SAXS. DMA data show that the PEO/MWNTs-g-PMMA blends containing up to 30 wt% MWNTs-g-PMMA are compatible. DSC data show the crystallization of PEO is enhanced by the MWNTs-g-PMMA, accompanying with a decreased thickness of crystal layers and an increased thickness of amorphous layers of the PEO lamellar stacks, in combination with SAXS data.  相似文献   

18.
Poly(ethylene oxide) (PEO)/organo clay nanocomposites were prepared by melt‐mixing using a laboratory kneader followed by compression molding. The nanocomposites were characterized by X‐ray diffraction, atomic force microscopy, and scanning electron microscopy. Their crystallization behavior in hot stage was investigated by polarized optical microscopy (POM). A decrease in size and regularity were observed as a result of incorporation of clay into the PEO matrix. The dynamic viscoelastic behavior of PEO/organo clay nanocomposites was assessed using a strain‐controlled parallel plate rheometer. The effects of clay concentration and the processing temperature on the rheological properties of the nanocomposites were extensively studied. A significant increase in the viscosity and storage modulus of the nanocomposites was found with the increasing clay content. The flow activation energy decreased with the incorporation of clay. The reinforcing effect of the organoclay was determined in dynamic mechanical analysis and tensile testing. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers  相似文献   

19.
The interaction behavior of solid‐state polymer electrolytes composed of poly(ethylene oxide) (PEO)/novolac‐type phenolic resin and lithium perchlorate (LiClO4) was investigated in detail by DSC, FTIR, ac impedance, DEA, solid‐state NMR, and TGA. The hydrogen bonding between the hydroxyl group of phenolic and ether oxygen of the PEO results in higher basicity of the PEO. The higher basicity of the ether group can dissolve the lithium salts more easily and results in a greater fraction of “free” anions and thus higher ionic conductivity. DEA results demonstrated that addition of the phenolic increases the dielectric constant because of the partially negative charge on the ether group induced by the hydrogen bonding interaction between ether oxygen and the hydroxyl group. The study showed that the blend of PEO(100)/LiClO4(25)/phenolic(15) possesses the highest ionic conductivity (1.5 × 10?5 S cm?1) with dimensional stability. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1207–1216, 2004  相似文献   

20.
The effect of cooling rate on the crystallization morphology and growth rate of poly(ethylene oxide) (PEO) and PEO/poly(methyl methacrylate) (PMMA) blends has been observed by Hot Stage Polarized Microscopy (HS‐POM). The isothermal crystallization kinetics study was carried out by differential scanning calorimetry (DSC). The spherulite morphology has been observed for the neat PEO with molecular weight of 6000 g/mol. By adding of PMMA with molecular weight of 39,300 g/mol, the growth fronts become irregular. With the increasing of PMMA content, the irregularity of growth front becomes more obvious, and the feather‐like morphology can be observed. When PMMA content is 60%, the spherulite is seriously destroyed. This phenomenon is more obvious for the slow cooling process. Based on the measurement of spherulite, the growth rate curves were obtained. According to the curves, it can be seen that the growth rate decreases with the increasing of PMMA content, and the growth rate during the slow cooling process is higher than that of the fast cooling process. The isothermal crystallization experiment indicates that the crystallization rate decreases dramatically with the increasing of PMMA content. And the Avrami parameter n was obtained, which is non‐integral and less than 3. Finally, it can be concluded that the higher value of n can be obtained for the condition with low crystallization rate. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41705.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号