Mechanical properties and biodegradability of green composites based on biodegradable polyesters and lyocell fabric

Green composites composed of regenerated cellulose (lyocell) fabric and biodegradable polyesters [poly(3‐hydroxybutyrate‐co‐3‐hydroxyvarelate) (PHBV), poly(butylene succinate) (PBS), and poly(lactic acid) (PLA)] were prepared by compression‐molding method. The tensile moduli and strength of all the biodegradable polyester/lyocell composites increased with increasing fiber content. When the obtained PLA/lyocell composites were annealed at 100°C for 3 h, the tensile strength and moduli were lowered despite the increase of degree of crystallization of the PLA component. The SEM observation of the composites revealed that the surface of the annealed composite has many cracks caused by the shrinkage of the PLA adhered to lyocell fabric. Multilayered PLA/lyocell laminate composites showed considerably higher Izod impact strength than PLA. As a result of the soil viral test, although the order of higher weight loss for the single substance was lyocell > PHBV > PBS > PLA, the biodegradability of the green composites did not reflect the order of a single substance because of the structural defect of the composite. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3857–3863, 2004     

Fabrication of highly isotactic polypropylene fibers to substitute asbestos in reinforced cement composites and analysis of the fiber formation mechanism

Highly isotactic polypropylene (PP) is currently studied as a cement‐reinforcement fiber that could potentially be substituted for asbestos because of its resistance to prolonged high‐temperature curing. The higher the isotacticity of the PP fiber is, the higher the tensile modulus and breaking strength of the cured fiber are. The PP fiber that exhibits a isotacticity of 99.6% (XI) and draw ratio of 6.0 retains a tensile modulus of 4.23 GPa, even after high‐temperature curing at 175°C for 5 h. PP fiber is cut into 6‐mm lengths and dispersed throughout a cement mixture to prepare a reinforced cement composite. The mixture is cured in an autoclave at 175°C for 5 h. The Charpy impact strength and flexural strength of the obtained cement composite tends to increase with increasing PP isotacticity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 981‐988, 2013     

Synthesis and characterization of chlorinated soy oil based epoxy resin/glass fiber composites

Composites with good toughness properties were prepared from chemically modified soy epoxy resin and glass fiber without additional petroleum based toughening agent. Chlorinated soy epoxy (CSE) resin was prepared from soybean oil. The CSE was characterised by spectral, and titration method. The prepared CSE was blended with commercial epoxy resin in different ratios and cured at 85°C for 3 h, and post cured at 225°C for 2 h using m‐phenylene diamine (MPDA) as curing agent. The cure temperatures of epoxy/CSE/MPDA with different compositions were found to be in the range of (151.2–187.5°C). The composite laminates were fabricated using epoxy /CSE/MPDA‐glass fiber at different compositions. The mechanical properties such as tensile strength (248–299 MPa), tensile modulus (2.4–3.4 GPa), flexural strength (346–379 MPa), flexural modulus (6.3–7.8 GPa) and impact strength (29.7–34.2) were determined. The impact strength increased with the increase in the CSE content. The interlaminor fracture toughness (G_IC) values also increased from 0.6953 KJ/m² for neat epoxy resin to 0.9514 KJ/m² for 15%CSE epoxy‐modified system. Thermogravimetric studies reveal that the thermal stability of the neat epoxy resin was decreased by incorporation of CSE. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Bio-based Epoxy Resins from Epoxidized Plant Oils and Their Shape Memory Behaviors

In this study, bio‐based epoxy materials containing functionalized plant oil, such as epoxidized soybean oil (ESO) and epoxidized linseed oil (ELO), were processed with 4‐methylhexahydrophthalic anhydride (MHPA) as a curing agent. In the presence of tetraethylammonium bromide, the curing reaction of epoxidized plant oil and MHPA proceeded at 130 °C to give transparent plant oil‐based epoxy materials. The resulting bio‐based epoxy materials exhibited relatively soft and flexible characters, due to the aliphatic chains of plant oil. The thermal and mechanical properties of the ESO/MHPA polymers depended on the feed molar ratio of anhydride to oxirane. The mechanical properties such as tensile strength and Young's modulus of the ELO/MHPA polymer increased, compared with those of the ESO/MHPA polymer. The glass transition temperature of the ELO/MHPA polymer was higher than that of the ESO/MHPA polymer, because of the high oxirane number of ELO. Furthermore, the ELO/MHPA polymer showed excellent shape memory property.     

Interpenetrating polymer network structured thermosets prepared from epoxidized soybean oil/diglycidyl ether of bisphenol A

Epoxidized soybean oil (ESO)/diglycidyl ether of bisphenol A (DGEBA) in various blend ratios (i.e. 100/0, 90/10, 80/20, 70/30, 60/40, 50/50) was thermally cured using methylhexahydrophthalic anhydride in the presence of 2‐ethyl‐4‐methylimidazole catalyst. The tensile properties and fracture toughness of the ESO/DGEBA thermoset blends were determined. Thermal properties of the blends were characterized using dynamic mechanical analysis, differential scanning calorimetry and thermogravimetric analysis. Blending of ESO and DGEBA gave synergistic effects on the modulus, strength, glass transition temperature and thermal stability. However, the fracture toughness and elongation at break of ESO/DGEBA blends are lower than those of ESO, as expected. The enhancement in certain mechanical and thermal properties of ESO/DGEBA can be associated with the crosslink density, gel content and possible interpenetrating network of the resulting thermoset blends. © 2013 Society of Chemical Industry     

Preparation and properties of biocomposites composed of epoxidized soybean oil,tannic acid,and microfibrillated cellulose

As a new biobased epoxy resin system, epoxidized soybean oil (ESO) was cured with tannic acid (TA) under various conditions. When the curing conditions were optimized for the improvement of the thermal and mechanical properties, the most balanced properties were obtained when the system was cured at 210°C for 2 h at an epoxy/hydroxyl ratio of 1.0/1.4. The tensile strength and modulus and tan δ peak temperature measured by dynamic mechanical analysis for the ESO–TA cured under the optimized condition were 15.1 MPa, 458 MPa, and 58°C, respectively. Next, we prepared biocomposites of ESO, TA, and microfibrillated cellulose (MFC) with MFC contents from 5 to 11 wt % by mixing an ethanol solution of ESO and TA with MFC and subsequently drying and curing the composites under the optimized conditions. The ESO–TA–MFC composites showed the highest tan δ peak temperature (61°C) and tensile strength (26.3 MPa) at an MFC content of 9 wt %. The tensile modulus of the composites increased with increasing MFC content and reached 1.33 GPa at an MFC content of 11 wt %. Scanning electron microscopy observation revealed that MFC was homogeneously distributed in the matrix for the composite with an MFC content of 9 wt %, whereas some aggregated MFC was observed in the composite with 11 wt % MFC. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

ACETYLATED PLANT-FIBER-REINFORCED POLYESTER COMPOSITES: A STUDY OF MECHANICAL,HYGROTHERMAL, AND AGING CHARACTERISTICS

The potential of acetylation of plant fibers to improve the properties of composites was studied. The chemical modification of oil palm empty fruit bunch (EFB), coconut fiber (Coir), oil palm frond (OPF), jute, and flax using noncatalyzed acetic anhydride were investigated. Proof of acetylation was indicated by the increase in weight percent gain (WPG). Acetylation at a reaction temperature of 120°C had resulted in the reduction in the tensile properties (stress, modulus, and elongation at break) of EFB and Coir composites. However, at 100°C, the acetylated samples exhibited improved properties. The mechanical properties of acetylated EFB- and Coir-fiber-reinforced polyester composites was evaluated at different fiber loadings. The tensile strength and modulus were improved, but elongation at break was slightly reduced upon acetylation, particularly at high fiber loading. Impact properties were moderately increased for those composites with fiber loadings up to 45%. Acetylation exhibited a low moisture absorption, comparable with glass-fiber composites. Acetylated EFB and Coir composites showed superior retention of tensile and impact properties after aging in water up to 12 months.     

Surface treatment of phosphate glass fibers using 2‐hydroxyethyl methacrylate: Fabrication of poly(caprolactone)‐based composites

2‐Hydroxyethyl methacrylate (HEMA) solution (1–10 wt %) was prepared in methanol and phosphate glass fibers were immersed in that solution for 5 min before being cured (irradiation time: 30 min) under UV radiation. Maximum polymer loading (HEMA content) was found for the 5 wt % HEMA solution. Degradation tests of the fibers in aqueous medium at 37°C suggested that the degradation of the HEMA‐treated fibers was lower than that of the untreated fibers. X‐ray photoelectron spectroscopy revealed that HEMA was present on the surface of the fibers. Using 5 wt % HEMA‐treated fibers, poly(caprolactone) matrix unidirectional composites were fabricated by in situ polymerization and compression molding. For in situ polymerization, it was found that 5 wt % HEMA‐treated fiber‐based composites had higher bending strength (13.8% greater) and modulus (14.0% greater) than those of the control composites. For compression molded composites, the bending strength and modulus values for the HEMA‐treated samples were found to be 27.0 and 31.5% higher, respectively, than the control samples. The tensile strength, tensile modulus, and impact strength of the HEMA composites found significant improvement than that of the untreated composites. The composites were investigated by scanning electron microscopy after 6 weeks of degradation in water at 37°C. It was found that HEMA‐treated fibers inside the composite retained much of their original integrity while the control samples degraded significantly. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Biodegradable polyurethane elastomers prepared from isocyanate‐terminated poly(ethylene adipate), castor oil,and glycerol

The curing reaction of tolylene‐2,4‐diisocyanate‐terminated poly(ethylene adipate) (PEA‐TDI) with a mixture of castor oil (CO) and glycerol (GO) with a NCO/OH ratio of 1.0 at 150°C gave crosslinked polyurethane (CO/GO‐PU). All the polyurethanes were elastomeric materials at room temperature. The glass‐transition temperature of the CO/GO‐PU increased with decreasing CO/GO ratio. All the cured polyurethanes had a higher 5% weight loss temperature than PEA‐TDI. The tensile strength and modulus of the polyurethanes increased with decreasing CO/GO ratio, and tensile residual strain after 300% elongation for all the CO/GO‐PUs was almost 0. All the polyurethanes had biodegradability, when measured by a biochemical oxygen demand method in an aqueous medium using activated sludge. The rate of the biodegradation of the polyurethanes increased with an increase of CO/GO ratio. The crosslinked CO‐PU showed much higher biodegradability than the linear PEA‐TDI. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and properties of biocomposites composed of glycerol‐based epoxy resins,tannic acid,and wood flour

After polyglycerol polyglycidyl ether (PGPE) and glycerol polyglycidyl ether (GPE) were mixed with tannic acid (TA) in ethanol and without solvent at epoxy/hydroxyl ratio 1/1, the obtained GPE‐TA and PGPE‐TA solutions were mixed with wood flour (WF), prepolymerized at 50°C, and subsequently compressed at 160°C for 3 h to give GPE‐TA/WF and PGPE‐TA/WF biocomposites with WF content 50–70 wt %, respectively. The storage moduli of the biocomposites in the rubbery state at more than 80°C were much higher than that of the control cured resins. The PGPE‐TA/WF composites had higher tensile modulus and rather lower tensile strength than PGPE‐TA. On the other hand, both the tensile modulus and strength of GPE‐TA/WF were much higher than those of GPE‐TA (2.4 GPa and 37 MPa). Those values of GPE‐TA/WF increased with WF content, became maximal values (5.1 GPa and 51 MPa) at WF content 60 wt %, and were lowered at 70 wt %. FE‐SEM analysis of the fractured surface of the biocomposites revealed that WF is tightly incorporated into the crosslinked epoxy resins. As a result of optimization of the epoxy/hydroxyl molar ratio for GPE‐TA/WF composite with WF content 60 wt %, the composite prepared at the ratio of 1.0/0.8 showed the highest tensile modulus and strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Biodegradable composites of poly(butylene succinate‐co‐butylene adipate) reinforced by poly(lactic acid) fibers

Biodegradable composites of poly(butylene succinate‐co‐butylene adipate) (PBSA) reinforced by poly(lactic acid) (PLA) fibers were developed by hot compression and characterized by Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), dynamic mechanical analyzer, and tensile testing. The results show that PBSA and PLA are immiscible, but their interface can be improved by processing conditions. In particular, their interface and the resulting mechanical properties strongly depend on processing temperature. When the temperature is below 120 °C, the bound between PBSA and PLA fiber is weak, which results in lower tensile modulus and strength. When the processing temperature is higher (greater than 160 °C), the relaxation of polymer chain destroyed the molecular orientation microstructure of the PLA fiber, which results in weakening mechanical properties of the fiber then weakening reinforcement function. Both tensile modulus and strength of the composites increased significantly, in particular for the materials reinforced by long fiber. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43530.     

The effects of long‐term exposure of flax fiber reinforced polymer to salt solution at high temperature on tensile properties

Most research on natural fiber composites has been primarily conducted on randomly‐oriented fibers. This study is focused on the short‐ and long‐term performances of flax fiber‐reinforced polymer (Flax‐FRP) made from continuous unidirectional fiber mats, and compares it to Glass‐FRP composite. The study looked into the effect of number of layers on properties, comparing wet layup (WL) to vacuum bag (VB) molding, and aging in a 3.5% salt solution for up to 365 days at 23, 40, and 55°C. Results show that Flax‐FRP has a tensile strength and modulus of one third the values of Glass‐FRP. Using the VB process, Flax‐FRP showed a strength and modulus 18 and 36% higher, respectively, than WL specimens. As the number of layers increased from one to five, the strength and modulus also increased but stabilized at three layers. After 365 days of conditioning at 23, 40, and 55°C, WL specimens showed a strength retention of 81, 73, and 69%, respectively. Using the Arrhenius relationship, it was estimated that both WL and VB Flax‐FRP would retain 60% of their tensile strength after 100 years of saltwater exposure at an annual mean temperature of 10°C. POLYM. COMPOS., 37:3234–3244, 2016. © 2015 Society of Plastics Engineers     

Preparation and properties of bio‐based epoxy montomorillonite nanocomposites derived from polyglycerol polyglycidyl ether and ε‐polylysine

Glycerol polyglycidyl ether (GPE) and polyglycerol polyglycidyl ether (PGPE) were cured with ε‐poly(L ‐lysine) (PL) using epoxy/amine ratios of 1 : 1 and 2 : 1 to create bio‐based epoxy cross‐linked resins. When PGPE was used as an epoxy resin and the epoxy/amine ratio was 1 : 1, the cured neat resin showed the greatest glass transition temperature (T_g), as measured by differential scanning calorimetry. Next, the mixture of PGPE, PL, and montomorillonite (MMT) at an epoxy/amine ratio of 1 : 1 in water was dried and cured finally at 110°C to create PGPE‐PL/MMT composites. The X‐ray diffraction and transmission electron microscopy measurements revealed that the composites with MMT content 7–15 wt % were exfoliated nanocomposites and the composite with MMT content 20 wt % was an intercalated nanocomposite. The T_g and storage modulus at 50–100°C for the PGPE‐PL/MMT composites measured by DMA increased with increasing MMT content until 15 wt % and decreased at 20 wt %. The tensile strength and modulus of the PGPE‐PL/MMT composites (MMT content 15 wt %: 42 and 5300 MPa) were much greater than those of the cured PGPE‐PL resin (4 and 6 MPa). Aerobic biodegradability of the PGPE‐PL in an aqueous medium was ～ 4% after 90 days, and the PGPE‐PL/MMT nanocomposites with MMT content 7–15 wt % showed lower biodegradability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Enhancement of PVC/ENR blend properties by poly(methyl acrylate) grafted oil palm empty fruit bunch fiber

Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150°C, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Young's modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Young's modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the impact strength, UTS, and elongation at break of the composites were found to decrease with the increase in fiber loading. An increase in elongation at break and UTS and decrease in the flexural and Young's modulus was observed with the addition of PMA‐g‐OPEFB fiber compared to ungrafted fiber. This observation indicates that grafting of PMA onto OPEFB impart some flexibility to the blend. The morphology of cryogenically fractured and tensile fracture surfaces of the composites, examined by a scanning electron microscope shows that the adhesion between the fiber and the matrix is improved upon grafting of the OPEFB fiber. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dry jet‐wet spinning of bagasse/N‐methylmorpholine‐N‐oxide hydrate solution and physical properties of lyocell fibres

Sugarcane bagasse, a cheap cellulosic waste material, was investigated as a raw material for producing lyocell fibers at a reduced cost. In this study, bagasse was dissolved in N‐methylmorpholine‐N‐oxide (NMMO) 0.9 hydrate, and fibers were prepared by the dry jet‐wet spinning method with coagulation in an aqueous NMMO solution. The effects of NMMO in 0 to 50% concentrations on the physical properties of fibers were investigated. The coagulating bath contained water/NMMO (10%) solution produced fiber with the highest drawability and highest physical properties. The cross‐section morphology of these fibers reveals fibrillation due to the high degree of crystallinity and high molecular orientation. In the higher NMMO concentrated baths (30 to 50%), the prepared fibers were hollow inside, which could be useful to make highly absorbent materials. The lyocell fibers prepared from bagasse have a tensile strength of 510 MPa, initial modulus of 30 GPa, and dynamic modulus of approximately 41 GPa. These properties are very comparable with those of commercial lyocell fibers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

A novel high performance RTM resin based on benzoxazine

Resin transfer molding (RTM) has the potential to manufacture high quality, geometrically complex composite parts. Benzoxazine is a new kind of high performance composite matrix. It can be polymerized with a ring‐opening reaction without releasing volatiles. In this article, a novel RTM resin made from aromatic diamine, phenol and formaldehyde is reported. The viscosity and curing behavior of the RTM resin as well as the properties of the cured neat resin and fiber reinforced composite were investigated. The resin has a viscosity lower than 0.5 Pa · s after 4 hr at 100°C, and can be cured at 180°C. The tensile strength, modulus, and elongation of the cast resin are 94 MPa, 4.6 GPa, and 2.2%, respectively. The flexural strength and modulus of the cast resin are 160 MPa and 4.9 GPa. The flexural strength and modulus of its glass fiber laminate are 662 MPa and 30 GPa. It is very easy to control the viscosity and curing rate of the RTM resin through the addition of reactive dilute agents and catalysts according to the requirement of RTM processing. POLYM. COMPOS., 26:563–571, 2005. © 2005 Society of Plastics Engineers     

Synthesis and characterization of bis(4‐cyanato 3,5‐dimethylphenyl) naphthyl methane/epoxy/glass fiber composites

Bis(4‐cyanato 3,5‐dimethylphenyl) naphthylmethane was prepared by treating CNBr with bis(4‐hydroxy 3,5‐dimethylphenyl) naphthylmethane in the presence of triethylamine at −5 to 5°C. The dicyanate was characterized by FT‐IR and NMR techniques. The prepared dicyanate was blended with commercial epoxy resin in different ratios and cured at 120°C for 1 hr, 180°C for 1 hr, and post cured at 220°C for 1 hr using diamino diphenyl methane (DDM) as curing agent. Castings of neat resin and blends were prepared and characterized by FT‐IR technique. The morphology of the blends was evaluated by SEM analysis. The composite laminates were also fabricated from the same composition using glass fiber. The mechanical properties like tensile strength, flexural strength, and fracture toughness were measured as per ASTMD 3039, D 790, and D 5528, respectively. The tensile strength increased with increase in cyanate content (3, 6, and 9%) from 322 to 355 MPa. The fracture toughness values also increased from 0.7671 kJ/m² for neat epoxy resin to 0.8615 kJ/m² for 9% cyanate ester epoxy modified system. The thermal properties were also studied. The 10% weight loss temperature of pure epoxy is 358°C and it increased to 398°C with incorporation of cyanate ester resin. The incorporation of cyanate ester up to 9% loading level does not affect the T_g to a very great extent. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Melt spinning of poly(L‐lactic acid) and its biodegradability

The melt spinning and melt drawing of poly(L ‐lactic acid) (PLLA) were carried out with a melt‐spinning machine, and the mechanical properties, structure, and biodegradability of PLLA fiber were investigated. PLLA fiber with a tensile strength of 0.81 GPa was successfully obtained through two steps of drawing at a draw ratio of 18 in hot water. This fiber had enough tensile strength for common engineering use. The fiber could be degraded under controlled composting conditions at 70°C for 1 week. In scanning electron microscopy observations of the fiber, a regular pattern of cracks running along the vertical direction to the fiber axis was clearly observed. This suggested that the PLLA fiber built up a highly ordered structure arranged along the direction of the fiber axis. After the fiber was left to lie in the ground for 1 year, however, the surface of the fiber was still smooth, and the tensile strength did not decrease much. This PLLA fiber could not be hydrolyzed after 1 month of steeping in a buffer solution at 37°C, but it was rapidly hydrolyzed at more than 60°C. It was suggested that the degradation (hydrolysis) rate of PLLA depended on the glass‐transition temperature. Upon hydrolysis at 80°C for 48 h, a regular crack along the vertical direction to the fiber axis was found that was very similar to that observed in degradation under composting conditions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2118–2124, 2005     

Preparation of gelatin fiber by gel spinning and its mechanical properties

A gel‐spinning process was used in an attempt to prepare a gelatin fiber with a high level of drawability. A gel fiber prepared by extrusion of 15 wt % gelatin in dimethyl sulfoxide into methanol at ?20°C was drawn to sixteen times the original length. After extraction of the dispersion medium, the mechanical strength of the fiber increased markedly with the draw ratio, and the fiber exhibited a tensile strength of 146 MPa and a Young's modulus of 2.3 GPa when drawn to the maximum. A gelatin fiber with greater mechanical strength was obtained when ethylene glycol was used as the spinning solvent. The X‐ray diffraction profile indicated the formation of triple‐helical structures and their lateral association, which is responsible for the mechanical strength of the fiber. Heat‐treatment improved the water‐resistance of the prepared fiber. γ‐Irradiation and treatment with glutaraldehyde improved the mechanical strength of the fiber. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical properties and microstructure of poly(ethylene terephthalate) microfiber prepared by carbon dioxide laser heating

We determined that a poly(ethylene terephthalate) microfiber was easily obtained by irradiating a carbon dioxide laser to an annealed fiber. The annealed fiber was prepared by zone drawing and zone annealing. First, an original fiber was zone drawn at a drawing temperature of 90°C under an applied tension of 4.9 MPa, and the zone‐drawn fiber was subsequently zone annealed at 150°C under 50.9 MPa. The zone‐annealed fiber had a degree of crystallinity of 48%, a birefringence of 218.9 × 10^?3, tensile modulus of 18.8 GPa, and tensile strength of 0.88 GPa. The microfiber prepared by laser heating the zone‐annealed fiber had a diameter of 1.5 μm, birefringence of 172.8 × 10^?3, tensile modulus of 17.6 GPa, and tensile strength of 1.01 GPa. The draw ratio estimated from the diameter was 9165 times; such a high draw ratio has thus far not been achievable by any conventional drawing method. Microfibers may be made more easily by laser heating than by conventional technologies such as conjugate spinning. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1955–1958, 2003