Fabrication and properties of porous Si3N4 ceramics by aqueous gelcasting using low-toxic DMAA gelling agent

A low-toxic and water-soluble monomer N, N-dimethylacrylamide (DMAA) was employed as a gelling agent in the gelcasting of porous Si₃N₄ ceramics. The process conditions and composition for slurry preparation (with a solid loading of 36?vol%), the consolidation and sintering of green bodies were investigated and optimized. The effects of various factors such as zeta potential, pH value of the premix solution, dispersant dosage and ball milling time on the rheological properties of the slurries were investigated. The results suggest that the best rheological properties (66.5 mPa.s at a shear rate of 96.3?s^?1) of the slurries were obtained when pH value ranged between 9 and 11, dispersant dosage reached 1?wt%, and ball milling time was 6?h. All the as-prepared green bodies showed a homogeneous microstructure and high flexural strength ≥ 26?MPa with a maximum up to 46.3?MPa when the ratio of DMAA to MBAM, initiator dosage, polymerization temperature and time were 14, 1?wt%, 70?°C and 90?min, respectively. The sintered bodies had a homogeneous microstructure, excellent and regulatable properties, a flexural strength of 216.3–327.3?MPa, and a porosity of 39.6–29.1% by varying the sintering temperature from 1710?°C to 1810?°C and the holding time from 1?h to 3?h. The superior comprehensive effect makes DMAA a promising candidate for an environmentally friendly gelling agent in gelcasting of porous Si₃N₄ ceramics.     

The effect of gelcasting parameters on microstructural optimization of porous Si3N4 ceramics

In this article we are reporting the optimization of gelcasting process which enabled us to manufacture silicon nitride bodies with around 30–37% porosity and 182–250?MPa flexural strength. Owing to their potential applications mainly in biomedical and aerospace, porous ${\text{Si}}_3{\text{N}}_4$ ceramics have gained ever increasing interests. However, the main challenge has been ensuring their high strength while maintaining high porosity. ${\text{Si}}_3{\text{N}}_4$ bodies were prepared via a controlled gelcasting followed by pressureless sintering in a coke bed. Monomers including acrylamide (AM) and $\text{N},{\text{N}}^{\text{'}}$ -methylenebisacrylamide (MBAM) were employed to formulate the primary slurry. Sub-micron ${\text{Si}}_3{\text{N}}_4$ powder of 35?vol% was used as solid loading where ammonium persulfate (APS) and $\text{N},\text{N},{\text{N}}^{\text{'}},{\text{N}}^{\text{'}}$ -tetramethylethylenediamine (TEMED) were added to initiate and catalyze polymerization reactions. Sintering was carried out at 1650?°C for 2–6?h and at 1750?°C for 2?h where 6?wt% mixture of ${\text{Al}}_2{\text{O}}_3?{\text{Y}}_2{\text{O}}_3$ was included as a sintering aid. Phase characterization and microstructural evolution were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively; while mechanical evaluation was based on bending test. It was found that by optimizing the viscosity of slurry and the idle time of gelation, a well distribution of high porosity structure is developed. The high strength of the sintered bodies is related to a high volume and unique microstructure of fine and elongated β- ${\text{Si}}_3{\text{N}}_4$ grains evolved during optimized sintering conditions. At temperatures above 1650?°C and sintering times of more than 4?h, the strength is decreased due to coarsening of β- ${\text{Si}}_3{\text{N}}_4$ grains, however.     

The effect of oxidation on the mechanical properties and dielectric properties of porous Si3N4 ceramics

The effect of oxidation temperature and time on the microstructures, phase compositions, mechanical properties, and dielectric properties of porous Si₃N₄ ceramics was investigated in the temperature range from 900 °C to 1300 °C for 1 h, 5 h, and 24 h. The weight gain measured either at lower temperature (900 °C) for long time (24 h) or at higher temperature (1300 °C) for 1 h demonstrated that the porous Si₃N₄ ceramics were easily oxidized under the current test conditions. Results showed that the amount of open pores, flexural strength, compressive strength, and dielectric constant all decreased with the increase of oxidation temperature independent upon the oxidation time. The oxidation product SiO₂ was low-temperature quartz in mild condition (low temperature, short time) and cristobalite in severe condition (high temperature, long time). The existence of cracks on the oxide scale was due to the phase transformation of SiO₂ and thermal expansion coefficient mismatch between SiO₂ and Si₃N₄.     

Preparation,mechanical, dielectric and microwave absorption properties of hierarchical porous SiCnw-Si3N4 composite ceramics

Herein, hierarchical porous SiC_nw-Si₃N₄ composite ceramics with good electromagnetic absorption properties were prepared. A porous Si₃N₄ matrix with different pore structures was first prepared by gelcasting-pressureless sintering (G-PLS) and gelcasting combined with particle stabilized foam-pressureless sintering (G-PSF-PLS). SiC_nw was then introduced by catalytic chemical vapor deposition (CCVD). An increase in solid loading (25–40 vol%) decreased apparent porosity (47.7–41.3%) and improved flexural strength (142.19–240.36 MPa) and fracture toughness (2.25–3.68 MPa·m^1/2). The addition of foam stabilizer propyl gallate (PG, 0.5–1.0 wt%) significantly increased apparent porosity (73.2–86.4%) and realized large-sized spherical pores, reducing flexural strength (58.23–38.56 MPa) and fracture toughness (0.75–0.41 MPa·m^1/2). High apparent porosity and large-sized pores facilitated the introduction of SiC_nw. The 25 vol% sample exhibited a reflection loss of ? 14.67 dB with an effective absorption bandwidth of 3.47 GHz, suggesting a development potential in the electromagnetic wave absorption field.     

Microstructure and mechanical properties of in-situ grown mullite toughened 3Y-TZP zirconia ceramics fabricated by gelcasting

In-situ grown mullite toughened zirconia ceramics (mullite-zirconia ceramics) with excellent mechanical properties for potential applications in dental materials were fabricated by gelcasting combined with pressureless sintering. The effect of sintering temperature on the microstructure and mechanical properties of mullite-zirconia ceramics was investigated. The results indicated that the columnar mullite produced by reaction was evenly distributed in the zirconia matrix and the content and size of that increased with the increase of sintering temperature. Mullite-zirconia ceramics sintered at 1500 °C had the optimum content and size of the columnar mullite phase, generating the excellent mechanical properties (the bend strength of 890.4 MPa, the fracture toughness of 10.2 MPa.m^1/2, the Vickers hardness of 13.2 GPa and the highest densification). On the other hand, zirconia particles were evenly distributed inside the columnar mullite, which improved the mechanical properties of columnar mullite because of pinning effect. All of this clearly confirmed that zirconia grains strengthened columnar mullite, and thus the columnar mullite was more effective in enhancing the zirconia-based ceramics. Simultaneously, the residual alumina after reaction was distributed evenly in the form of particle, which improved the mechanical properties of the sample because of pinning effect. Overall, the synergistic effect of zirconia phase transformation toughening with mullite and alumina secondary toughening improved the mechanical properties of zirconia ceramics.     

Microstructure and mechanical properties of Si3N4f/Si3N4 composites with different coatings

The Si₃N₄ coating and Si₃N₄ coating with Si₃N₄ whiskers as reinforcement (Si₃N_4w-Si₃N₄) were prepared by chemical vapor deposition (CVD) on two-dimensional silicon nitride fiber reinforced silicon nitride ceramic matrix composites (2D Si₃N_4f/Si₃N₄ composites). The effects of process parameters of as-prepared coating including the preparation temperature and volume fraction of Si₃N_4w on the microstructure and mechanical properties of the composites were investigated. Compared with Si₃N₄ coating, Si₃N_4w-Si₃N₄ coating shows more significant effect on the strength and toughness of the composites, and both strengthening and toughening mechanism were analyzed.     

Novel porous Si3N4 ceramics prepared by aqueous gelcasting using Si3N4 poly-hollow microspheres as pore-forming agent

In this paper, novel porous Si₃N₄ ceramics were prepared by aqueous gelcasting using Si₃N₄ poly-hollow microspheres as pore-forming agent. The effect of Si₃N₄ poly-hollow microsphere content on the phase composition, microstructure, shrinkage, porosity and mechanical properties of the prepared porous Si₃N₄ ceramics were investigated. It is found that there is only β-Si₃N₄ phase in all the prepared porous Si₃N₄ ceramics. Meanwhile, the SEM results show that the pores in the porous Si₃N₄ ceramics distribute uniformly, the added Si₃N₄ poly-hollow microspheres and the basal body contact closely. With the increase of Si₃N₄ poly-hollow microsphere content, the shrinkage of the porous Si₃N₄ ceramics decreases gradually, and the porosity of the porous Si₃N₄ ceramics decreases firstly and then increases. Furthermore, the flexural strength and fracture toughness of the porous Si₃N₄ ceramics decrease with the increase of the Si₃N₄ poly-hollow microsphere content.     

Enhanced mechanical properties of Si3N4 ceramics with ZrB2-B binary additives prepared at low temperature

Phase composition, microstructures, and mechanical properties of silicon nitride (Si₃N₄) ceramics were investigated with ZrB₂ and B additives. Results showed that the addition of ZrB₂ and/or B in 2.5 and 5 vol.% promoted the phase transformation of α- to β-Si₃N₄ phase and the formation of bimodal microstructure after hot-pressing at 1500 °C. With the introduction of 2.5 vol.% (ZrB₂-B) binary additives, fracture toughness and strength of Si₃N₄ ceramics increased significantly from 5.2 MPa m^1/2 and 384 MPa to 7.2 MPa m^1/2 and 675 MPa, respectively. However, the hardness of ceramics decreased slightly from 23.5 GPa to 21.3 GPa, which was still higher than typical values reported on Si₃N₄ ceramics (15˜17 GPa).     

Effects of fiber aspect ratio and fabrication temperature on the microstructure and mechanical properties of elastic fibrous porous ceramics by press-filtration method

The inherent brittleness of fibrous porous ceramics (FPCs) results in their fragility, limiting their application in thermal protection. In this paper, a novel elastic fibrous porous ceramic (EFPCs) with quasi-layered structure were successfully prepared by facile press-filtration method. To further investigate the characteristics of EFPCs, the effect of fiber aspect ratio and fabrication temperature on the microstructures and properties were studied. Results demonstrated that both fiber aspect ratio and fabrication temperature had influence on the microstructure and mechanical properties on EFPCs. The prepared EFPCs exhibited low density (0.124–0.181 g cm^?3), relatively high compressive stress (0.096–0.377 MPa) compared to flexible fibrous ceramics, high porosity (91.73%–94.86%) and low thermal conductivity (～0.03 W m^?1 k^?1). According to these excellent properties, the EFPCs may have potential use in thermal insulation fields.     

Influence of hexagonal boron nitride nanosheets on phase transformation,microstructure evolution and mechanical properties of Si3N4 ceramics

Fully dense Si₃N₄ materials with 1 wt.% (～ 1.5 vol.%) and 2 wt.% (～ 3.0 vol.%) h-BN nanosheets were prepared by spark plasma sintering at 1750 °C with the dwell of 7 min under a pressure of 50 MPa in a vacuum. BN nanosheets with different dimensions were prepared by ultrasound-assisted liquid phase exfoliation of h-BN powder, followed by centrifugation at different speeds (1000 rpm and 3000 rpm). The addition of BN nanosheets hindered the particle rearrangement stage of sintering, which resulted in the delayed α→β phase transformation of Si₃N₄. To study a direct effect of BN nanosheets on the mechanical properties of Si₃N₄, the results were compared to the monolithic Si₃N₄ with similar grain size and α/β-Si₃N₄ ratio. The addition of 2 wt.% h-BN nanosheets (1000 rpm) increased both the fracture toughness (～ 26 %) and the strength (～ 45 %) of Si₃N₄, when compared to the monolithic Si₃N₄ with similar microstructure.     

Microstructure and mechanical properties of tantalum carbide ceramics: Effects of Si3N4 as sintering aid

Stoichiometric Tantalum carbide (TaC) ceramics were prepared by reaction spark plasma sintering using 0.333–2.50 mol% Si₃N₄ as sintering aid. Effects of the Si₃N₄ addition on densification, microstructure and mechanical properties of the TaC ceramics were investigated. Si₃N₄ reacted with TaC and tantalum oxides such as Ta₂O₅ to form a small concentration of tantalum silicides, SiC and SiO₂, with significant decrease in oxygen content in the consolidated TaC ceramics. Dense TaC ceramics having relative densities >97% could be obtained at 0.667% Si₃N₄ addition and above. Average grain size in the consolidated TaC ceramics decreased from 11 µm at 0.333 mol% Si₃N₄ to 4 µm at 2.50 mol% Si₃N₄ addition. The Young's modulus, Vickers hardness and flexural strength at room temperature of the TaC ceramic with 2.50 mol% Si₃N₄ addition was 508 GPa, 15.5 GPa and 605 MPa, respectively. A slight decrease in bending strength was observed at 1200 °C due to oxidation of the samples.     

Effect of polystyrene addition on properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics with high strength and high transmittance have been widely used in the field of defense and military. Additive manufacturing (AM) technology is one of the effective means to fabricate porous Si₃N₄ ceramics. Nevertheless, it is difficult to prepare porous Si₃N₄ ceramics by using digital light processing (DLP) because of the large refractive index difference between Si₃N₄ powders and photosensitive resin. In this study, the effects of the amount of polystyrene (PS) powders on the properties of Si₃N₄ ceramic slurries and sintered ceramics were systematically discussed. The addition of PS reduced the overall refractive index of powders and increased the average particle size of powders, thus improving the cure depth of Si₃N₄ ceramic slurries from 11.0 ± 2.0 μm to 55.7 ± 1.8 μm. With the increase of PS content, the shrinkage and porosity of Si₃N₄ ceramics gradually increased, and the bulk density and flexural strength showed the opposite trend. The slurry with low viscosity (2.38 Pa٠s at a shear rate of 30 s⁻¹) and high cure depth (51.2 ± 4.6 μm) was obtained when the content of PS was 15 wt%, which met the thickness requirements for printing. The total porosity of Si₃N₄ ceramics reached the maximum values at 28.21 ± 2.58%. The addition of PS solved the problem of low cure depth of slurries, and PS as a pore-forming agent could help Si₃N₄ ceramics form porous structure. This research provides valuable insights into the fabrication of non-oxide ceramics with high refractive index using DLP technology.     

Influence of solid loading on densification behavior,micromorphology and dielectric properties of Ba0.67Sr0.33TiO3 ceramics fabricated by a novel DCC-HVCI method

Ba_0.67Sr_0.33TiO₃ (BST) ceramics with highly improved dielectric performance were fabricated by a novel direct coagulation casting via high valence counter ions (DCC-HVCI) method. The influence of solid loading on densification behavior, micromorphology, and dielectric performance of the samples was investigated. With the increase of solid loading from 40 to 50 vol%, the maximum densification rate of BST ceramics increased from 0.090 to 0.122 s⁻¹, and the densification temperature decreased from 1424 to 1343 °C, which indicated that high solid loading could promote the densification behavior of samples during sintering. BST ceramics fabricated by the DCC-HVCI method showed uniform grain size and microstructure, which was beneficial for the dielectric properties of BST ceramics. Samples obtained from 45 vol% suspensions possessed the lowest dielectric permittivity (ε_r ≈ 2801), and the dielectric loss (tanδ≈0.0262) was about 1/10 of that of dry-pressed samples (tanδ≈0.301), which could be attributed to the composition homogenization.     

Effects of AlN inorganic binder on the properties of porous Si3N4 ceramics prepared by selective laser sintering

Porous Si₃N₄ ceramics are widely used in the aerospace field due to its lightweight, high-strength, and high wave transmission. Traditional manufacturing methods are difficult to fabricate complex structural and functional ceramic parts. In this paper, selective laser sintering (SLS) technology was applied to prepare porous Si₃N₄ ceramics using AlN as an inorganic binder. And the effects of AlN content on the properties of the obtained ceramic samples were explored. As the AlN content increased, nano-Al₂O₃ and nano-SiO₂ formed the eutectic liquid phase, enhancing the sintering densification and phase transformation of Si₃N₄ poly-hollow microspheres (PHMs). The island-like partial densification structures in Si₃N₄ green bodies increased. During the high-temperature sintering, the eutectic liquid phase partially transformed into the mullite phase or reacted with AlN and Si₃N₄ to form the Sialon phase. With the increase of AlN content, the fracture mode of Si₃N₄ ceramics changed from fracturing along PHMs to fracturing across PHMs. The bonding depth between PHMs increased and the connection between the grains was tighter, so the Si₃N₄ ceramics became denser. With the increase of AlN addition, the total porosity of the porous Si₃N₄ ceramics tended to decrease and the flexural strength gradually increased. When AlN content was 20 wt%, the total porosity and the flexural strength were 33.6% and 23.9 MPa, respectively. The addition of AlN inorganic binder was carried out to develop a novel way to prepare high-performance porous Si₃N₄ ceramics by SLS.     

Preparation and properties of porous ceramics from nickel slag by aerogel gelcasting

To further resource industrial solid waste, porous ceramics with high porosity were prepared by a gelcasting method using nickel slag and kaolin as raw materials and hydrophilic nontoxic SiO₂ aerogel as a gelling agent. The effects of nickel slag content, dispersant and solid content on the properties and microstructure of porous ceramics were investigated in detail in terms of density, compressive strength, porosity, phase composition and micromorphology. The results confirmed that a certain amount of nickel slag can effectively improve the porosity of porous ceramics, while the addition of dispersant can promote the flow of the slurry, enhanced the denseness of the raw billet and significantly improved the compressive strength. However, its excessive use had a negative effect on the ceramic density and porosity. At the same time, the solid content played a key role in the performance of porous ceramics prepared by gelcasting, and too much solid content was also not conducive to the generation of pores. When the nickel slag content was 55%, the amount of dispersant was 2%, and the solid content was 60 vol%, the porous ceramic had a better overall performance, the density of the porous ceramic was 510 kg/m³, the compressive strength was 1.3 MPa, and the porosity reached 80.1%. The major crystalline phases of porous ceramics prepared by nickel slag were cordierite and anorthite.     

Mechanical properties and microstructure of Al2O3-SiCw ceramic tool material toughened by Si3N4 particles

Al₂O₃-SiC_w toughened ceramic tools play vital role in high-speed machining of nickel-based superalloys due to their superior mechanical properties. Herein, owing to synergistic toughening mechanism, α-Si₃N₄ particles are employed as reinforcement phase into Al₂O₃-SiC_w ceramic composite to optimize mechanical properties of Al₂O₃-SiC_w ceramic tools. Moreover, the influence of Si₃N₄ content and sintering parameters on microstructure and mechanical properties of Al₂O₃-20 vol%SiC_w ceramic tool material is systematically investigated. Results reveal that appropriate amount of Si₃N₄ particles is required to effectively increase the density of Al₂O₃-SiC_w ceramic composites. The presence of Si₃N₄ particles leads to formation of novel β-sialon phase during hot-press sintering, which effectively enhances fracture toughness and flexural strength of Al₂O₃-SiC_w ceramic composites. It is observed that grain size of newly formed β-sialon phase is extremely sensitive to hot-pressing sintering conditions. The degree of chemical transformation of α-Si₃N₄ into Si_6-zAl_zO_zN_8-z (β-sialon) and z-value of Si_6-zAl_zO_zN_8-z are significantly influenced by sintering temperature. Overall, Al₂O₃-20 vol%SiC_w-15 vol%Si₃N₄ ceramic tool material, with 1.5 vol%Y₂O₃-0.5 vol%La₂O₃-0.5 vol%CeO₂ (YLC) sintering additive, rendered optimal mechanical properties after sintering at 1600 °C under 32 MPa for 30 min. Improved mechanical performance can be ascribed to synergistic toughening and strengthening influence of whiskers and particles.     

The preparation of silicon nitride ceramics by gelcasting and pressureless sintering

A new gelling system based on the polymerization of hydantion epoxy resin and 3,3′-Diaminodipropylamine (DPTA) was successfully developed for fabricating silicon nitride (Si₃N₄) ceramics. The effects of pH value, the dispersant content, solid volume fraction and hydantion epoxy resin amount on the rheological properties of the Si₃N₄ slurries were investigated. The relative density of green body obtained from the solid loading of 52 vol% Si₃N₄ slurry reached up to 62.7%. As the concentration of hydantion epoxy resin increased from 5 wt% to 20 wt%, the flexural strength of Si₃N₄ green body enhanced from 5.3 MPa to 31.6 MPa. After pressureless sintering at 1780 °C for 80 min, the sintered samples exhibited the unique interlocking microstructure of elongated β-Si₃N₄ grains, which was beneficial to improve the mechanical properties of Si₃N₄ ceramics. The relative density, flexural strength and fracture toughness of Si₃N₄ ceramics reached 97.8%, 687 MPa and 6.5 MPa m^1/2, respectively.     

Effect of ZrB2 and its oxide impurities (ZrO2 and B2O3) on hot-pressed Si3N4 ceramics at low temperature

Based on the previous work on Si₃N₄-ZrB₂, the addition of 2.5 vol.% ZrB₂ promoted α- to β-Si₃N₄ phase transformation, bimodal microstructure, and toughness and strength improvement after hot-pressing at 1500 °C. However, the mechanism needed to be further explored. In the present work, the effect of ZrB₂ and its oxide impurities (ZrO₂ and B₂O₃) on phase composition, microstructure and mechanical properties of Si₃N₄ ceramics with MgO-Yb₂O₃ additives were studied. Results showed that the addition of B₂O₃ had no influence on Si₃N₄ ceramics, whereas the addition of ZrO₂ inhibited the α- to β-Si₃N₄ phase transformation, formed an uniform equiaxed microstructure, and deceased the toughness and strength. The positive effect of oxide impurities can be eliminated. Based on the STEM analysis, the possible reason was that the addition of ZrB₂ led to the formation of Si-Mg-O-N-Yb-Zr-B liquid phase, and then promoted α- to β-Si₃N₄ phase transformation.     

Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics are highly regarded as ideal materials for radomes due to their unique characteristics. However, the slurry used for the preparation of porous Si₃N₄ ceramics suffers from a low cure depth, making it challenging to fabricate ceramic components using DLP technology. In this study, porous Si₃N₄ ceramics were prepared by combining DLP technology with pore-forming agent method. The addition of polymethyl methacrylate (PMMA) powders with lower refractive index than that of Si₃N₄ powders can improve the penetration depth of ultraviolet light in the Si₃N₄ slurry. A systematic study was conducted to investigate the influence of the addition of PMMA powders on the properties of Si₃N₄ slurries and porous Si₃N₄ ceramics. When PMMA powders were added at 10 wt%, the slurry with a lowest viscosity of 0.13 Pa s (the shear rate is 30 s⁻¹) and cure depth of 40.0 μm (the exposure energy is 600 mJ/cm²) was obtained. With the increase of PMMA content, porous Si₃N₄ ceramics experienced a gradual decrease in both the flexural strength and bulk density, while the porosity increased from 14.41% to 27.62%. Specifically, when 20 wt% PMMA was added, the resulting porous Si₃N₄ ceramics had a lowest bulk density (2.41 g/cm³), a maximum porosity (27.62%), and a flexural strength (435.87 MPa). The study is of great significance in establishing an experimental foundation for fabricating porous Si₃N₄ ceramics by using DLP technology.     

Si3N4-BN-SiCN ceramics with unique hetero-interfaces for enhancing microwave absorption properties

SiCN-based ceramics with broadband and strong microwave absorption properties are desired for the structural and functional integration of ceramic matrix composites. The elemental composition and thermal expansion coefficients of the ceramics matrix crucially affect its microstructure and electromagnetic wave (EMW) absorption properties. BN layer with lower electrical conductivity and higher specific area, exhibits both the impedance matching characteristic and EMW attenuation in the process of multiple reflections, electrical conductivity loss, dipole polarization and interfacial polarization. Therefore, Si₃N₄-BN-SiCN ceramics, which were synthesized using chemical vapor infiltration (CVI) method, construct unique hetero-interface of Si₃N₄-BN, Si₃N₄–SiCN and BN-SiCN. Therefore, the Si₃N₄-BN-SiCN ceramics have outstanding EMW absorption performance and realize an effective absorption bandwidth (EAB) that covers the whole X band and the minimum reflection coefficient (RC) reaches -18.43 dB at a thickness of 3.37 mm.