Effect of stacking sequence on mechanical properties of hybrid flax/jute fibers reinforced thermoplastic composites

In this study, the hybrid composites were prepared by stacking jute/PP nonwoven and flax/MAPP woven fabrics in defined sequences. Polypropylene (PP) and maleic anhydride grafted polypropylene (MAPP) were used as matrix materials. Jute and flax fibers were treated with alkali solution in order to improve the interface properties of the resultant composites. The mechanical properties of these hybrid composites were analyzed by means of tensile, flexural, and drop‐weight impact tests. The effect of fabric stacking sequence on the mechanical properties of the composites was investigated. The stacking of nonwovens at the top and in alternate layers has resulted in maximum flexural strength, flexural stiffness, and impact force. It was also shown that hybrid composites have improved tensile, flexural, and impact properties in comparison to neat PP matrix. POLYM. COMPOS., 36:2167–2173, 2015. © 2014 Society of Plastics Engineers     

Silica‐filled polypropylene composites: The effect of ethylene diamine dilaurate and maleic anhydride grafted polypropylene on mechanical properties,water absorption,morphology, and thermal properties

The effect of two compatibilizers, i.e. ethylene diamine dilaurate (EDD) and maleic anhydride grafted polypropylene (MAPP) on the mechanical properties, water absorption, morphology, and thermal properties of silica‐filled polypropylene (PP/Sil) composites were studied. The results show that the tensile, impact and flexural strengths (up to 2 php), Young's modulus, and elongation at break (Eb) increased with increasing EDD content. However, increasing MAPP content increases the tensile strength, Young's modulus, impact and flexural strengths, and water absorption resistance. At a similar compatibilizer content, EDD exhibits higher Eb, impact and flexural strengths but lowers tensile strength, Young's modulus, and water absorption resistance compared with MAPP. Scanning electron microscopy study of tensile fractured surfaces exhibits the evidence of better silica‐PP adhesion with MAPP and EDD compared with the similar composites but without compatibilizer. Fourier transform infra red spectra provide an evidence of interaction between EDD or MAPP with PP/Sil composites. Termogravimetry analysis results indicate that the addition of EDD or MAPP slightly increases the thermal stability of PP/Sil composites. Differential scanning calorimetry also indicates that PP/Sil composites with EDD or MAPP have higher heat fusion (ΔH_f(com)) and crystallinity (X_com) than similar composites but without compatibilizer. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

High Stiffness Natural Fiber‐Reinforced Hybrid Polypropylene Composites

Abstract

Natural fibers are potentially a high‐performance non‐abrasive reinforcing fiber source. In this study, pulp fibers [including bleached Kraft pulp (BKP) and thermomechanical pulp (TMP)], hemp, flax, and wood flour were used for reinforcing in polypropylene (PP) composite. The results show that pulp fibers, in particular, TMP‐reinforced PP has the highest tensile strength, possibly because pulp fibers were subjected to less severe shortening during compounding, compared to hemp and flax fiber bundles. Maleic‐anhydride grafted PP (MAPP) with high maleic anhydride groups and high molecular weight was more effective in improving strength properties of PP composite as a compatiblizer. Coupled with 10% glass fiber, 40% TMP reinforced PP had a tensile strength of 70 MPa and a specific tensile strength comparable to glass fiber reinforced PP. Thermomechanical pulp was more effective in reinforcing than BKP. X‐ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) were used to aid in the analysis. Polypropylene with high impact strength was also used in compounding to improve the low‐impact strength prevalent in natural fiber‐reinforced PP from injection molding.     

Maleic anhydride polypropylene modified cellulose nanofibril polypropylene nanocomposites with enhanced impact strength

Development of cellulose nanofibrils (CNFs) reinforced polypropylene (PP) nanocomposites using melt compounding processes has received considerable attention. The main challenges are to obtain well‐dispersed CNFs in the polymer matrix and to establish compatible linkages between the CNFs and PP. Manufacturing of CNF reinforced PP nanocomposites was conducted using a twin‐screw co‐rotating extruder with the masterbatch concept. Modifications of CNFs using maleic anhydride polypropylene were performed. The best mechanical properties of the nanocomposites are 1.94 GPa (tensile modulus), 32.8 MPa (tensile strength), 1.63 GPa (flexural modulus), 50.1 MPa (flexural strength), and 3.8 kJ m⁻² (impact strength), which represents about 36, 11, 21, 7, and 23% improvement, respectively, compared to those of pure PP (1.43 GPa, 29.5 MPa, 1.35 GPa, 46.9 MPa, and 3.1 kJ m⁻²). Fracture morphology examination indicated good dispersion of CNFs in the PP matrix was achieved through this specific manufacturing process. MAPP treatments enhanced the interfacial adhesion between the CNFs and PP. POLYM. COMPOS., 37:782–793, 2016. © 2014 Society of Plastics Engineers     

Influence of interfacial adhesion on the structural and mechanical behavior of PP‐banana/glass hybrid composites

Hybrid composites of polypropylene (PP), reinforced with short banana and glass fibers were fabricated using Haake torque rheocord followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both fibers into PP matrix resulted in increase of tensile strength, flexural strength, and impact strength upto 30 wt% with an optimum strength observed at 2 wt% MAPP treated 15 wt% banana and 15 wt% glass fiber. The rate of water absorption for the hybrid composites was decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has been analyzed to investigate the interfacial properties. An increase in storage modulus (E′) of the treated‐composite indicates higher stiffness. The loss tangent (tan δ) spectra confirms a strong influence of fiber loading and coupling agent concentration on the α and β relaxation process of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out through differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA), indicated an increase in the crystallization temperature and thermal stability of PP with the incorporation of MAPP‐treated banana and glass fiber. POLYM. COMPOS., 31:1247–1257, 2010. © 2009 Society of Plastics Engineers     

Impact modification of polypropylene‐based composites using surface‐coated waste rubber crumbs

Blends of maleated polypropylene (MAPP) with high contents of waste rubber powder, namely ground tire rubber and waste ethylene propylene diene monomer (EPDM) powder, were used as impact modifiers for polypropylene (PP) based composites with different reinforcements (hemp, talc, and milled glass fiber). Adding reinforcements led to increase in modulus (tensile, flexural, and torsion moduli) of PP, while its impact strength decreased noticeably. Impact modification of PP‐based composites was successfully performed via inclusion of MAPP/waste rubber compounds, especially compounds containing waste EPDM powder. Inclusion of such impact modifiers increased impact strength of composites over 80%. The effects of impact modification were more significant for hemp‐ and glass‐filled composites compared to composites containing talc. However, slight decrease in tensile, flexural, and torsion moduli (up to 30%) of the composites was also observed after inclusion of impact modifiers. POLYM. COMPOS., 35:2280–2289, 2014. © 2014 Society of Plastics Engineers     

Morphological,mechanical, and physical properties of composites made with wood flour‐reinforced polypropylene/recycled poly(ethylene terephthalate) blends

Wood flour (WF)‐filled composites based on a polypropylene (PP)/recycled polyethylene terephthalate (r‐PET) matrix were prepared using two‐step extrusion. Maleic anhydride grafted polypropylene (MAPP) was added to improve the compatibility between polymer matrices and WF. The effects of filler and MAPP compatibilization on the water absorption, mechanical properties, and morphological features of PP/r‐PET/WF composites were investigated. The addition of MAPP significantly improved mechanical properties such as tensile strength, flexural strength, tensile modulus, and flexural modulus compared with uncompatibilized composites, but decreased elongation at break. Scanning electron microscopic images of fracture surface specimens revealed better interfacial interaction between WF and polymer matrix for MAPP‐compatibilized PP/r‐PET/WF composites. MAPP‐compatibilized PP/r‐PET/WF composites also showed reduced water absorption due to improved interfacial bonding, which limited the amount of absorbable water molecules. These results indicated that MAPP acts as an effective compatibilizer in PP/r‐PET/WF composites. POLYM. COMPOS., 38:1749–1755, 2017. © 2015 Society of Plastics Engineers     

Effects of hygrothermal ageing on mechanical properties of flax pulps and their polypropylene matrix composites

The aim of this work was to study the kinetics of water uptake and its influence on mechanical behavior of both flax pulps and their composites with a maleic anhydride polypropylene copolymer (MAPP) modified polypropylene (PP) matrix by immersion in distilled water at 30, 50, 70, and 100°C. Both the influence of two different MAPP compatibilizers and the optimum doses of each ones were analyzed. The kinetics of water uptake was studied from weight measurements at regular interval times. The diffusion coefficient was dependent on the immersion temperature and MAPP content. Tensile modulus and strength of single flax fiber decreased by water immersion. Both flexural strength and modulus of composites decreased as a result of the combined effect of thermal ageing and moisture absorption. MAPP coupling agent increases moisture resistance and mechanical properties for MAPP‐modified systems with respect to the unmodified ones. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3438–3445, 2006     

Impact and flexural properties of stone‐ground wood pulp‐reinforced polypropylene composites

This study analyses the flexural and impact strength of polypropylene reinforced with stone ground wood pulp (SGWP) and the effect of a maleated‐polypropylene (MAPP) coupling agent on the mechanical properties of these composites. Composites prepared in the absence of the coupling agent showed a very light positive linear evolution of the flexural strength with the percentage of reinforcing fiber. In contrast, composites that included MAPP in their formulation presented highly noticeable improvements with fiber content. By applying mathematical modeling strategies, the flexural modulus has been analyzed using the Cox–Krenchel model. Similarly, the flexural and tensile strength factors for the reinforcing fiber have been defined and utterly allowed for the determination of intrinsic fiber flexural strength. POLYM. COMPOS., 34:842–848, 2013. © 2013 Society of Plastics Engineers     

Maleic anhydride grafted polypropylene as a coupling agent for polypropylene composites filled with ink‐eliminated waste paper sludge flour

Ink‐eliminated sludge flour (IESF), a waste residue from the recycling treatment of waste paper, is a promising new kind of filler for thermoplastic polymers with a good price/performance ratio and advantages for environmental protection. In this study, high‐impact polypropylene (PP) and maleic anhydride grafted polypropylene (MAPP) were chosen as a polymer matrix and a coupling agent, respectively, for the preparation of IESF/PP composites, and the structures and properties of the obtained composites were also investigated. The experimental results revealed that IESF not only induced the crystallization orientation of PP along the b axis but also had a restraining effect on the formation of the β phase during the recrystallization of PP from the melt; the addition of MAPP further strengthened this effect to some extent. In addition, the proper addition of MAPP was helpful for improving the thermal stability of the IESF/PP composites. With the strengthening of the interfacial interaction between the IESF and PP matrix by MAPP, the resultant efficient stress transfer from the PP matrix to the IESF particles led to increased tensile and flexural strength. However, the original greater rigidity of MAPP, with respect to PP, reduced the toughness of the composites and caused some negative effects on the impact strength and the elongation at break. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2320–2325, 2004     

Effect of fiber/matrix chemical modification on the mechanical properties and water absorption of extruded flax/polypropylene composite

Compound of flax/polypropylene (PP) is characterized concerning the mechanical properties of stiffness, strength, and impact in addition to the water absorption behavior. Manufacturing takes place by twin‐screw extruder. The extruder screw layout is modified through different kneading elements to get high fiber aspect ratio. Sodium hydroxide solution was used as a washing solution for the flax fibers' surfaces. Both fiber and matrix are chemically modified. Selected groups of the fibers were further treated using trimethoxyvinylsilan TMVS and acrylic acid AA. The PP matrix is also treated with different coupling agents; namely, maleated PP MAPP, TMVS‐MAPP, and acrylic acid‐functionalized PP AAPP. The combinations of different fiber/matrix are extruder compounded, injection molded, and finally tested. Fiber modification seems to be positive with AA‐modified surface. AAPP matrix modification improves the stiffness four times that of the untreated flax/PP. Till 30 and 40 wt %, the more the fiber is the more the strength and stiffness, respectively. MAPP‐modified matrix improves the mechanical properties and keeps low water absorption values. AAPP‐modified matrix shows the best stiffness values. TMVS‐MAPP does not seem to have distinguished improvement compared with MAPP. NaOH‐TMVS/MAPP and NaOH‐TMVS/AAPP systems can serve as alternatives to the normal NaOH/MAPP treatment. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of wheat straw fiber content and characteristics,and coupling agent concentration on the mechanical properties of wheat straw fiber‐polypropylene composites

Wheat straw fiber‐polypropylene (PP) composites were prepared to investigate the effects of wheat straw fiber content (10, 20, 30, 40, and 50 wt %), fiber size (9, 28, and 35 mesh), and maleic anhydride grafted polypropylene (MAPP) concentration (1, 2, 5, and 10 wt %) on the static and dynamic mechanical properties of the wheat straw fiber‐PP composites in this study. The tensile modulus and strength of the composites increased linearly with increasing wheat straw fiber content up to 40%, whereas the elongation at break decreased dramatically to 3.78%. Compared with the composites made of the longer wheat straw fiber, the composites made of the fines (>35 mesh) had a slightly higher tensile strength of 31.2 MPa and tensile elongation of 5.39% at break. With increasing MAPP concentration, the composites showed an increase in tensile strength, and the highest tensile strength of 34.0 MPa occurred when the MAPP concentration reached 10 wt %. As wheat straw fiber content increased from 0 to 40%, the flexural modulus of the composites increased gradually from 1335 to 3437 MPa. The MAPP concentration and wheat straw fiber size distribution had no appreciable effect on the static flexural modulus of the composites. The storage flexural modulus of the composites increased with increasing wheat straw fiber content. The scanning electron microscopy (SEM) observation on the fracture surface of the composites indicated that a high wheat straw fiber content (>30 wt %) resulted in fiber agglomeration and a reduction in interfacial bonding strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

热塑性复合材料板材拉伸强度近似计算

针对热塑性复合材料拉伸强度,以亚麻增强聚丙烯机织层合复合材料板材为例,结合理论分析,首先对其进行理想条件下的强度计算,通过推导得到理想状况下的强度理论计算公式,进而结合具体试验条件,在此理论计算公式基础上引进板材经、纬向纤维伸直系数aj、aw作为修正系数进行修正。利用多项式拟合,最终得出符合试验条件下的强度近似计算公式及拟合曲线。     

Effect of hybridization and compatibilization on the mechanical properties of recycled polypropylene‐hemp composites

Hemp fibers and particles, with different sizes and contents, were used to make hybrid composites based on recycled polypropylene (PP). In particular, the effect of maleated polypropylene (MAPP) addition on the morphology and mechanical properties is reported. The results show that better adhesion is obtained with MAPP addition. In general, fiber content and size had a substantial effect on the tensile, flexural, torsion, and impact properties of the resulting composites. Although, adding MAPP to the samples improved the impact strength of the composites, the values were always lower than neat PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

亚麻增强热塑性树脂复合材料板材的研究与应用

以亚麻纤维为增强体,与聚丙烯(PP)纤维按一定比例进行混合,然后制备加捻纱及PP长丝包覆的包覆纱,并利用机织工艺织成二维机织布作为复合材料的预制铺层.采用层合热压方法制备PP/亚麻纤维复合材料板材.通过对板材弯曲性能的测试及分析,研究了制备工艺、纱线结构及亚麻纤维含量等因素对复合材料弯曲性能的影响.     

Flax fibre physical structure and its effect on composite properties: Impact strength and thermo-mechanical properties

Earlier investigations by the authors showed that the tensile modulus of flax fibre mat polypropylene composites (NMT) could surpass the values of glass mat reinforced thermoplastic (GMT) on fibre weight basis. The tensile and flexural strength could reach values of up to 65% of the GMT strength values, however, very much dependent on the fibre physical structure. This study deals with the Charpy impact and the thermo-mechanical properties of flax NMT materials. The trend is that the Charpy impact strength decreases with increasing fibre internal bonding and enhanced fibre-matrix adhesion, which is opposite to the trend for the tensile and flexural properties. The impact strength of the NMT materials is lower than generally reported for GMT materials. Dynamic mechanical thermal analysis reveals that with increasing temperature the storage modulus of the NMT materials reduces more slowly when the fibre internal bonding and the fibre-matrix adhesion are improved. In order to approach the tensile, flexural and impact strength of GMT materials, composites should be based on the strong elementary flax fibres. The axial tensile strength of elementary fibres approaches the strength of glass fibres and the lateral strength of the elementary fibres is higher than the technical flax fibres lateral strength. The thermo-mechanical properties can probably be improved when non-cellulosic material can be removed from the flax fibre surface without damaging the fibre.     

MAPP/EAA处理对聚丙烯/小麦秸秆粉复合材料性能的影响

研究了马来酸酐接枝聚丙烯（MAPP）、乙烯丙烯酸共聚物（EAA）处理对聚丙烯（PP） /小麦秸秆粉（WSP）复合材料性能的影响。结果表明,随着体系中MAPP质量份数的增加,PP/WSP的拉伸强度和弯曲强度均逐渐增大,但冲击强度却先增加后减小,复合材料达到塑化峰的时间逐渐延长;使用EAA后,无论体系中是否已经使用了MAPP,PP/WSP的拉伸、弯曲和冲击强度均可得以提高,特别对于未使用MAPP的体系,效果更加明显,可分别提高65.04 %、45.42 %和6.75 %,储能模量增加,表面疏水性增强,平衡扭矩从13.9 N·m降至11.8 N·m,吸水尺寸变化率及吸水率下降,吸水平衡时间缩短;使用EAA可改善PP/WSP中WSP与PP间的界面结合,改善PP/WSP力学性能、热稳定性能、表面疏水性能、尺寸稳定性能和加工性能,降低其吸水率。     

Preparation and characteristics of composites of high‐crystalline cellulose with polypropylene: Effects of maleated polypropylene and cellulose content

Binary composites of high‐crystalline fibrous cellulose with polypropylene (PP) or maleic anhydride‐grafted polypropylene (MAPP) were prepared by melt‐mixing with different contents of cellulose from 0 to 60 wt %. Ternary composites of cellulose with PP and MAPP were also prepared to investigate the effects of MAPP as a compatibilizer between cellulose and PP. Scanning electron microscopy revealed that the addition of MAPP generates strong interactions between a PP matrix and cellulose fibers: All cellulose fibers are encapsulated by layers of the matrix and connected tightly within the matrix. Thus, the tensile strength and Young's modulus of MAPP‐containing composites increase with an increase in MAPP and cellulose content, in contrast to the decrease in tensile strength of a PP‐based binary composite with an increase in cellulose. Cellulose fibers act as a nucleating agent for the crystallization of PP, which is promoted by the addition of MAPP through an increase of the crystallization temperature of PP in the composite. Accordingly, both cellulose and MAPP facilitate the thermooxidative stability of PP composites in the following order: MAPP/cellulose > PP/MAPP/cellulose > PP/cellulose > PP. Relative water absorption increases with an increase in cellulose content, decreasing with the addition of MAPP. MAPP‐containing cellulose composites have high potential for applications as environmentally friendly materials. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 337–345, 2003     

Strength degradation and fractographic analysis of carbon fiber reinforced polymer composite laminates with square / circular hole using scanning electron microscope micrographs

In this article, experimental study has been carried out to obtain comparative information intended for designing and assembly of structural components made of carbon fiber reinforced polymer (CFRP) composite. Investigation on tensile strength has been done on unidirectional CFRP composite laminates with hole. Effect of stacking sequence, hole size, and hole shape on tensile strength has been examined independently by open hole tensile (OHT) test. Reduction in OHT strength is observed when stacking sequence is changed from [0]₈ to [0/90]_2s and when the hole size is increased. However, OHT strength is noticed to get increased when hole shape is changed from circular to square. Laminates containing square shaped hole demonstrate less sensitiveness towards tensile strength and show negligible effect of stacking sequences on the normalized strength than the circular hole. Fractographic analysis figures out the failure mechanism of tested specimens by correlating their mechanical properties. SEM micrographs and data analysis reveal that axial splits and local delamination effectively blunt the stress concentration around the hole resulting in higher OHT strength and less notch sensitiveness towards tensile strength.     

Mechanical and open hole tensile properties of self‐reinforced PET composites with recycled PET fiber reinforcement

The tensile strength of notched composites is an important factor for composite structural design. However, no literature is available on the notch sensitivity of self‐reinforced polymer composites. In this study, self‐reinforced recycled poly (ethylene terephthalate) (srrPET) composites were produced by film stacking from fabrics composed of double covered uncommingled yarns (DCUY). Composite specimens were subjected to uniaxial tensile, flexural, and Izod impact tests and the related results compared with earlier ones achieved on srPET composites reinforced with nonrecycled technical PET fibers. Effects of open circular holes on the tensile strength of srrPETs were studied at various width‐to‐hole diameter (W/D) ratios of the specimens. In the open hole tensile (OHT) measurements bilinear (yielding followed by post‐yield hardening) stress–strain curves were recorded. The srrPET composites had extremely high yield strength retention (up to 142%) and high breaking strength retention (up to 81%) due to the superior ductile nature of the srrPETs, which induces plastic yielding near the hole thereby reducing the stress concentration effect. The results proved that srrPET composites are tough, ductile notch‐insensitive materials. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43682.