Structure–properties relationship in toughening of poly(butylene terephthalate) with core–shell modifier

The performance of acrylonitrile–butadiene–styrene (ABS) core–shell modifier with different grafting degree, acrylonitrile (AN) content, and core–shell ratio in toughening of poly(butylene terephthalate) (PBT) matrix was investigated. Results show PBT/ABS blends fracture in ductile mode when the grafting degree is high, and with the decrease of grafting degree PBT/ABS blends fracture in a brittle way. The surface of rubber particles cannot be covered perfectly for ABS with low grafting degree and agglomeration will take place; on the other hand, the entanglement density between SAN and PBT matrix decreases because of the low grafting degree, inducing poor interfacial adhesion. The compatibility between PBT and ABS results from the strong interaction between PBT and SAN copolymer and the interaction is influenced by AN content. Results show ABS cannot disperse in PBT matrix uniformly when AN content is zero and PBT/ABS fractures in a brittle way. With the addition of AN in ABS, PBT/ABS blends fracture in ductile mode. The core–shell ratio of ABS copolymers has important effect on PBT/ABS blends. When the core–shell ratio is higher than 60/40 or lower than 50/50, agglomeration or cocontinuous structure occurs and PBT/ABS blends display lower impact strength. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 5363–5371, 2006     

Polylactide toughening with epoxy‐functionalized grafted acrylonitrile–butadiene–styrene particles

Glycidyl methacrylate functionalized acrylonitrile–butadiene–styrene (ABS‐g‐GMA) particles were prepared and used to toughen polylactide (PLA). The characteristic absorption at 1728 cm^?1 of the Fourier transform infrared spectra indicated that glycidyl methacrylate (GMA) was grafted onto the polybutadiene phase of acrylonitrile–butadiene–styrene (ABS). Chemical reactions analysis indicated that compatibilization and crosslinking reactions took place simultaneously between the epoxy groups of ABS‐g‐GMA and the end carboxyl or hydroxyl groups of PLA and that the increase of GMA content improved the reaction degree. Scanning electron microscopy results showed that 1 wt % GMA was sufficient to satisfy the compatibilization and that ABS‐g‐GMA particles with 1 wt % GMA dispersed in PLA uniformly. A further increase of GMA content induced the agglomeration of ABS‐g‐GMA particles because of crosslinking reactions. Dynamic mechanical analysis testing showed that the miscibility between PLA and ABS improved with the introduction of GMA onto ABS particles because of compatibilization reactions. The storage modulus decreased for the PLA blends with increasing GMA content. The decrease in the storage modulus was due to the chemical reactions in the PLA/ABS‐g‐GMA blends, which improved the viscosity and decreased the crystallization of PLA. A notched impact strength of 540 J/m was achieved for the PLA/ABS‐g‐GMA blend with 1 wt % GMA, which was 27 times than the impact strength of pure PLA, and a further increase in the GMA content in the ABS‐g‐GMA particles was not beneficial to the toughness improvement. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

环氧官能化ABS增韧PBT树脂的性能研究

采用乳液聚合方法合成了甲基丙烯酸环氧丙酯(GMA)共聚的丙烯腈/丁二烯/苯乙烯核壳粒子ABS-g-GMA,用于不同分子量聚对苯二甲酸丁二醇酯(PBT)的增韧。红外光谱证明GMA接枝共聚到了ABS粒子上。DMA测试发现PBT与ABS、ABS-g-GMA之间有一定的相容性。SEM表明ABS-g-GMA均匀分散在不同分子量的PBT树脂中。ABS-g-GMA可以实现对PBT树脂的有效增韧,PBT树脂的分子量越大,增韧效率越高,共混物的断裂伸长率越大。     

Influence of the degree of grafting on the morphology and mechanical properties of blends of poly(butylene terephthalate) and glycidyl methacrylate grafted poly(ethylene‐co‐propylene) (EPR)

Poly(ethylene‐co‐propylene) (EPR) was functionalized to varying degrees with glycidyl methacrylate (GMA) by melt grafting processes. The EPR‐graft‐GMA elastomers were used to toughen poly(butylene terephthalate) (PBT). Results showed that the grafting degree strongly influenced the morphology and mechanical properties of PBT/EPR‐graft‐GMA blends. Compatibilization reactions between the carboxyl and/or hydroxyl of PBT and epoxy groups of EPR‐graft‐GMA induced smaller dispersed phase sizes and uniform dispersed phase distributions. However, higher degrees of grafting (>1.3) and dispersed phase contents (>10 wt%) led to higher viscosities and severe crosslinking reactions in PBT/EPR‐graft‐GMA blends, resulting in larger dispersed domains of PBT blends. Consistent with the change in morphology, the impact strength of the PBT blends increased with the increase in EPR‐graft‐GMA degrees of grafting for the same dispersion phase content when the degree of grafting was below 1.8. However, PBT/EPR‐graft‐GMA1.8 displayed much lower impact strength in the ductile region than a comparable PBT/EPR‐graft‐GMA1.3 blend (1.3 indicates degree of grafting). Morphology and mechanical results showed that EPR‐graft‐GMA 1.3 was more suitable in improving the toughness of PBT. SEM results showed that the shear yielding properties of the PBT matrix and cavitation of rubber particles were major toughening mechanisms. Copyright © 2006 Society of Chemical Industry     

Toughening of poly(butylene terephthalate) with epoxy-functionalized acrylonitrile-butadiene-styrene

Glycidyl methacrylate (GMA) functionalized acrylonitrile-butadiene-styrene (ABS) copolymers have been prepared via an emulsion polymerization process. These functionalized ABS copolymers (ABS-g-GMA) were blended with poly(butylene terephthalate) (PBT). DMA result showed PBT was partially miscible with ABS and ABS-g-GMA, and DSC test further identified the introduction of GMA improved miscibility between PBT and ABS. Scanning electron microscopy (SEM) displayed a very good dispersion of ABS-g-GMA particles in the PBT matrix compared with the PBT/ABS blend when the content of GMA in PBT/ABS-g-GMA blends was relatively low (<8 wt% in ABS-g-GMA). The improvement of the disperse phase morphology was due to interfacial reactions between PBT chains end and epoxy groups of GMA, resulting in the formation of PBT-co-ABS copolymer. However, a coarse, non-spherical phase morphology was obtained when the disperse phase contained a high GMA content (≥8 wt%) because of cross-linking reaction between the functional groups of PBT and GMA. Rheological measurements further identified the reactions between PBT and GMA. Mechanical tests showed the presence of only a small amount of GMA (1 wt%) within the disperse phase was sufficient to induce a pronounced improvement of the impact and tensile properties of PBT blends. SEM results showed shear yielding of PBT matrix and cavitation of rubber particles were the major toughening mechanisms.     

ACR-g-GMA的制备及对PBT的增韧

要采用乳液聚合方法合成了以丙烯酸丁酯(BA)为橡胶相内核,甲基丙烯酸甲酯(MMA)为壳层,并在壳层接枝甲基丙烯酸环氧丙酯(GMA)的核壳结构聚合物(AcR-g-GMA)。用其增韧聚对苯二甲酸丁二醇酯(PBT),制备PBT/ACR-g-GMA合金。用傅立叶变换红外光谱考察接枝聚合物的环氧基团;用电子显微镜观察共混物中粒子分布的微观形态;测试了共混物的力学性能。结果表明:采用乳液聚舍方法能够将GMA接枝到ACR上,GMA可以增强两相间的界面结合力,ACR-g-GMA粒子能有效地增韧PBT。当ACR-g-GMA粒子中GMA的质量分数为3%,m(PBT)/m(ACR-g-GMA)为80/20时,共混物的缺口冲击强度可高达389 J/m。     

环氧官能化ABS增韧PBT及其共混物

合成了甲基丙烯酸环氧丙酯(GMA)接枝的丙烯腈-丁二烯-苯乙烯(ABS-g-GMA)核壳粒子增韧聚对苯二甲酸丁二醇酯(PBT),加入环氧树脂(Epoxy)为扩链剂进一步提高共混物的性能。红外光谱(FTIR)结果表明:GMA成功接枝到ABS粒子上;研究发现不同GMA含量的ABS-g-GMA粒子在PBT及PBT/Epoxy共混物中均匀分散;ABS-g-GMA对PBT增韧效果较好,Epoxy进一步提高了PBT/ABS-g-GMA共混物的冲击韧性及拉伸强度;ABS-g-GMA增韧PBT的机理是橡胶粒子的空洞化和PBT基体的剪切屈服。     

ABS-g-GMA增韧聚对苯二甲酸丁二醇酯的研究

用甲基丙烯酸环氧丙酯（（MA）接枝的丙烯腈／丁二烯／苯乙烯（ABs）接枝共聚物（ABS-g-GMA）改善聚对苯二甲酸丁二醇酯（PBT）的缺口冲击韧性。动态力学分析、差示扫描量热分析以及流变性能测试结果表明，GMA引入到ABS中，随GMA含量的增加，PBT与ABS的玻璃化转变温度相互靠近，PBT的熔点降低，共混体系的扭矩、温度提高，这些结果表明GMA提高了PBT与ABS之间的相容性；增容反应导致ABS在PBT基体中均匀、稳定分散，有利于共混物性能的改善；交联反应导致交联聚集网状结构的生成，使共混物性能变差。冲击强度结果表明，1％（质量含量。下同）GMA含量就可以导致PBT／ABS-g-GMA共混物冲击韧性显著改善，当ABS-g-GMA1含量为30％时，共混物冲击强度高达850J／m。     

Toughening modification of PS with n‐BA/MMA/styrene core–shell structured copolymer from emulsifier‐free emulsion polymerization

Core–shell structured particles, which comprise the rubbery core and glassy layers, were prepared by emulsifier‐free emulsion polymerization of poly(n‐butyl acrylate/methyl methacrylate)/polystyrene [P(n‐BA/MMA)/PS]. The particle diameter was about 0.22 μm, and the rubbery core was uncrosslinked and lightly crosslinked, respectively. The smaller core–shell structured particle–toughened PS blends were investigated in detail. The dynamic mechanical behavior and observation by scanning electron microscopy of the modified blend system with core–shell structured particles indicated good compatibility between PS and the particles, which is the necessary qualification for an effective toughening modifier. Notched‐impact strength and related mechanical properties were measured for further evaluation of the toughening efficiency. The notched‐impact strength of the toughened PS blends with uncrosslinked particles reached almost sixfold higher than that of the untoughened PS when 15 phr of the core–shell structured particles was added. For the crosslinked particles the toughening effect for PS was not obvious. The toughening mechanism for these smaller particles also is discussed in this article. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1290–1297, 2003     

Phase morphology development during processing of compatibilized and uncompatibilized PBT/ABS blends

The development of the multiphase morphology of uncompatibilized blends of poly(butylene terephthalate) (PBT) and acrylonitrile–butadiene–styrene terpolymer (ABS) and PBT/ABS blends compatibilized with methyl‐methacrylate glycidyl‐methacrylate (MMA‐GMA) reactive copolymers during compounding in a twin‐screw extruder and subsequent injection molding was investigated. Uncompatibilized PBT/ABS 60/40 (wt %) and compatibilized PBT/ABS/MMA‐GMA with 2 and 5 wt % of MMA‐GMA showed refined cocontinuous morphologies at the front end of the extruder, which coarsened towards the extruder outlet. Coarsening in uncompatibilized PBT/ABS blends is much more pronounced than in the compatibilized PBT/ABS/MMA‐GMA equivalents and decreases with increasing amounts of the MMA‐GMA. For both systems, significant refinement on the phase morphology was found to occur after the blends pass through the extruder die. This phenomenon was correlated to the capacity of the die in promoting particles break‐up due to the extra elongational stresses developed at the matrix entrance. Injection molding induces coarsening of the ABS domains in the case of uncompatibilized PBT/ABS blends, while the reactive blend kept its refined phase morphology. Therefore, the compatibilization process of PBT/ABS/MMA‐GMA blends take place progressively leading to a further refinement of the phase morphology in the latter steps, owing to the slow reaction rate relative to epoxide functions and the carboxyl/hydroxyl groups. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 102–110, 2007     

Poly(methyl methacrylate) toughening with refractive index‐controlled core–shell composite particles

Poly(butylacrylate‐co‐styrene)/poly(methyl methacrylate) (PMMA) core–shell composite particles having different refractive indexes were prepared by a two‐stage consecutive emulsion polymerization. The refractive index of the core phase was controlled by varying the incorporated amount of divinylbenzene (DVB) which acted as a crosslinking agent as well as a refractive index enhancer. The blends of these core–shell composite particles with PMMA showed an impact strength increment of about three times compared with that of the pure PMMA. However, as the amount DVB increased, the impact strength showed a tendency toward decreasing. This was caused by the loss of the elastic property of the core phase. The toughened PMMA blended with core–shell composite particles having the core crosslinked with 1 wt % DVB showed the best transparency. However, the transparency was rather decreased, as the difference of the refractive index between the core phase and the pure PMMA increased. This suggested that in the case of using the core–shell composite particles as a toughening agent for PMMA the matching of the refractive index of the core phase with that of the pure PMMA was one of key factors in maintaining the transparency of the toughened PMMA. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1607–1614, 1999     

Modification of the reactive core-shell particles properties to prepare PBT/PC blends with higher toughness and stiffness

Glycidyl methacrylate (GMA) functionalized methyl methacrylate-butadiene-styrene core-shell particles (PB-g-MSG) were prepared to toughen poly (butylene terephthalate) (PBT) and polycarbonate (PC) blends. T-dodecyl mercaptan (TDDM) was used to modify the grafting character of the core-shell particles. The addition of TDDM decreased the grafting degree, particles size and crosslinking degree of PB-g-MSG particles. At the same time, the free methyl methacrylate-co-styrene-co-glyceryl methacrylate copolymer (f-MSG) increased. The f-MSG reacted with PBT and suppressed the transesterification between PBT and PC. On the other hand, f-MSG promoted the crystallization of PBT by heterogeneous nucleation. When the TDDM content was lower than 0.76%, PB-g-MSG particles dispersed in the matrix uniformly, otherwise, agglomeration took place. The change of TDDM content in the PB-g-MSG particles influenced the toughening ability and tensile properties. When the TDDM content was 0.76%, the PBT/PC/PB-g-MSG blend showed the optimum impact toughness and yield strength, which are 908 J/m and 49.4Mpa. Fracture mechanism results indicated that cavitation induced shear yielding occurred in the PBT/PC/PB-g-MSG blend when no TDDM addition for the core-shell particles. With the addition of TDDM, the interfacial strength decreased between the PB-g-MSG core-shell particles and the matrix. So voids appeared due to debonding, which also could promote the shear yielding process.     

Surface modification effects of core–shell rubber particles on the toughening of poly(butylene terephthalate)

We toughened poly(butylene terephthalate) (PBT) by loading core–shell rubber (CSR) type impact modifiers, consisting of a rubbery poly(n‐butyl acrylate) core and a rigid poly(methyl methacrylate) shell. To optimize the dispersion of CSR particles into the PBT matrix during melt compounding, the shell surface was modified with different grafting ratios of glycidyl methacrylate (GMA) reactive with PBT chain ends. In PBT blends with a 20 wt % CSR loading, the dispersed rubbery phases showed discernible shapes depending on the grafted GMA content, from predetermined spheres with 0.25 ± 0.05 μm diameters to their aggregates in the 2–3 μm diameter range. As a result, the interparticle spacing (τ) could be controlled from 0.25 to 4.0 μm in the PBT blends containing the fixed rubber loading. The Izod impact strengths of these samples increased significantly below τ = 0.4 μm. Additional thermal and morphological analyses strongly supported the hypothesis that the marked increase in toughness of the blends was related to less ordered lamellar formation of the PBT matrix under the confined geometry. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of the molecular structure of impact modifier and compatibilizer on the toughening of PBT/SBS/PS‐GMA blends

This work aims at studying the toughening process of poly(butylene terephthalate) (PBT) through its blends with styrene‐butadiene‐styrene block copolymers (SBS), in the presence of poly(styrene‐ran‐glicydil methacrylate) (PS‐GMA) as reactive compatibilizer. High values of impact strength were attained for PBT/SBS blends without the compatibilizer; however, this improvement is achieved for blends with SBS having similar viscosity compared to PBT, at high SBS content (40 wt %) and for blends prepared under specific processing conditions. The efficiency of the in situ compatibilization of PBT/SBS blends by PS‐GMA was found to be strongly dependent on the SBS and PS‐GMA molecular characteristics. Better compatibilizing results were observed through fine phase morphologies and lower ductile to brittle transition temperatures (DBTT) as the interfacial interaction and stability of the in situ formed compatibilizer are maximized, that is, when the miscibility between SBS and PS‐GMA and reaction degree between PBT and PS‐GMA are maximized. For the PBT/SBS/PS‐GMA blends under study, this was found when it is used the SBS with higher polystyrene content (38 wt %) and with longer PS blocks (M_w = 20,000 g mol^?1) and also the PS‐GMA with moderate GMA contents (4 wt %) and with molecular weight similar to the critical one for PS entanglements (M_c = 35,000 g mol^?1). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5795–5807, 2006     

Preparation and characterization of poly(butadiene-stat-styrene)/poly(styrene-stat-acrylonitrile) structured latex particles

In rubber toughening of thermoplastics, core/shell polymers have been used extensively. This work introduces the synthesis and characterization of polybutadiene based core/shell latex particles with controlled particle size and crosslinking density of the core. A lithium soap recipe was employed to prepare a series of poly(butadiene-stat-styrene) (90/10 by wt) core particles by conventional emulsion polymerization through a batch process. The shell polymer, poly(styrene-stat-acrylonitrile) (72/28 by wt), was polymerized by a semicontinuous process in the presence of the core particles to form a core/shell morphology. The effects of initiator concentration, monomer feeding rate, core/shell ratio, and gel-fraction of the core on the core/shell particle morphology were studied. The degree of grafting of the shell polymer on the core particles was determined as well. The morphology and glass transitions of these particles were characterized by transmission electron microscopy, differential scanning calorimetry, and dynamic mechanical spectroscopy. These latex particles can be used specifically in toughening polycarbonate. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1123–1134, 1997     

Deformation mechanism of polystyrene toughened with sub‐micrometer monodisperse rubber particles

Core–shell polybutadiene‐graft‐polystyrene (PB‐g‐PS) rubber particles with different ratios of polybutadiene to polystyrene were prepared by emulsion polymerization through grafting styrene onto polybutadiene latex. The weight ratio of polybutadiene to polystyrene ranged from 50/50 to 90/10. These core‐shell rubber particles were then blended with polystyrene to prepare PS/PB‐g‐PS blends with a constant rubber content of 20 wt%. PB‐g‐PS particles with a lower PB/PS ratio (≤70/30) form a homogeneous dispersion in the polystyrene matrix, and the Izod notched impact strength of these blends is higher than that of commercial high‐impact polystyrene (HIPS). It is generally accepted that polystyrene can only be toughened effectively by 1–3 µm rubber particles through a toughening mechanism of multiple crazings. However, the experimental results show that polystyrene can actually be toughened by monodisperse sub‐micrometer rubber particles. Scanning electron micrographs of the fracture surface and stress‐whitening zone of blends with a PB/PS ratio of 70/30 in PB‐g‐PS copolymer reveal a novel toughening mechanism of modified polystyrene, which may be shear yielding of the matrix, promoted by cavitation. Subsequently, a compression‐induced activation method was explored to compare the PS/PB‐g‐PS blends with commercial HIPS, and the result show that the toughening mechanisms of the two samples are different. Copyright © 2006 Society of Chemical Industry     

Toughening of poly(l‐lactide) modified by a small amount of acrylonitrile−butadiene−styrene core‐shell copolymer

A small amount of acrylonitrile‐butadiene‐styrene (ABS) core shell copolymer particles are used to improve the toughness of poly(l ‐lactide) (PLLA) matrix. The incorporation of ABS copolymer dramatically increased the elongation yield at break of PLLA. For PLLA blend with 6.0 wt % ABS copolymer particles, the elongation yield at break increased by 28 times and the notched impact strength improved by 100% comparing with those of neat PLLA. Fourier transformed infrared (FTIR) and dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM) measurement results indicated that the special polarity interaction between ester group of PLLA matrix and nitrile group of PSAN shell phase enhanced the interfacial adhesion between PB rubber phase and PLLA matrix and promoted the fine dispersion of ABS particles in PLLA matrix. Meanwhile, ABS core shell particles also showed a certain extent of effects on the crystallinity behavior of PLLA. A small amount of ABS particles became the nucleating sites, and then the degree of crystallinity of PLLA/ABS blends increased. However, the notched impact of PLLA blends decreased because of the aggregation of more ABS particles. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42554.     

Relationship between structure and properties in high‐performance PA6/SEBS‐g‐MA/(PPO/PS) blends: The role of PPO and PS

This work aimed at studying the role of poly(phenylene oxide) (PPO) and polystyrene (PS) in toughening polyamide‐6 (PA6)/styrene‐ethylene‐butadiene‐styrene block copolymer grafted with maleic anhydride (SEBS‐g‐MA) blends. The effects of weight ratio and content of PPO/PS on the morphology and mechanical behaviors of PA6/SEBS‐g‐MA/(PPO/PS) blends were studied by scanning electron microscope and mechanical tests. Driving by the interfacial tension and the spreading coefficient, the “core–shell” particles formed by PPO/PS (core) and SEBS‐g‐MA (shell) played the key role in toughening the PA6 blends. As PS improved the distribution of the “core–shell” particles due to its low viscosity, and PPO guaranteed the entanglement density of the PPO/PS phase, the 3/1 weight ratio of PPO/PS supplied the blends optimal mechanical properties. Within certain range, the increased content of PPO/PS could supply more efficient toughening particles and bring better mechanical properties. Thus, by adjusting the weight ratio and content of PPO and PS, the PA6/SEBS‐g‐MA/(PPO/PS) blends with excellent impact strength, high tensile strength, and good heat deflection temperature were obtained. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45281.     

Toughening of PA6 nanocomposites by reactive acrylonitrile–butadiene–styrene core–shell rubber particles

The effect of addition of organoclay and the reactive ABS‐g‐MA core‐shell particles on the mechanical properties and morphology of blends of polyamide (PA6) were reported. The reactive rubber particles with core‐shell structure were selected as modifier instead of conventional reactive bulk rubber. The microstructure of the ternary nanocomposites was characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). Impact strength and stress–strain behavior of blends were measured as a function of organoclay content and core/shell ratio of ABS‐g‐MA. The organoclay plates affected the interfacial adhesion between polyamide and the core‐shell particles because of a shielding effect of organclay on the interacting of amine end groups of PA6 with the MA groups of ABS‐g‐MA. The poor dispersion behavior of ternary nanocomposites was observed when the core/shell ratio is 80/20, and with an increase of organoclay content, the core/shell dispersed phase size increased. Blends based on the maleated elastomer with the core/shell ratio 60/40 gave a more beneficial balance of toughness versus stiffness. POLYM. COMPOS., 35:864–871, 2014. © 2013 Society of Plastics Engineers     

Toughness of ABS/PBT blends: The relationship between composition,morphology, and fracture behavior

A series of acrylonitrile–butadiene–styrene (ABS) copolymer/poly(butylene terephthalate) (PBT)/acrylonitrile‐styrene‐glycidyl methacrylate (ASG) blends with various compositions were prepared and characterized in this study. When the fraction of ABS exceeds a critical value there is a rapid increase in notched impact strength of ABS/PBT blends no matter whether the compatibilizer ASG is present. By combining morphology observation and notched impact results, we found that the ductile‐brittle transition of the blends is closely related to the morphology inversion. The notched impact strength jumps from 15.9 to 33.4 kJ/m² when phase inversion of ABS occurs at its fraction of 58 wt %. Accordingly, a possible toughening mechanism involved in the blends is proposed on the basis of a careful analysis of fracture energy, crack propagation behavior and fracture surface morphology. It is believed that the continuous ABS phase plays the critical role in toughening ABS/PBT blends. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46051.