A study of blending and complexation of poly(acrylic acid)/poly(vinyl pyrrolidone)

Poly(acrylic acid) (PAA) and poly(vinyl pyrrolidone) (PVP) were chosen to prepare polymer complex and blends. The complex was prepared from ethanol solution and the blends were prepared from 1-methyl-2-pyrrolidone solution. DSC results show that the T_gs of the PAA/PVP blends lie between those of the two constituent polymers, whereas T_g of the PAA/PVP complex is higher than both blends and the two constituent polymers. TGA results show that degradation temperature, T_d, of PAA increases upon adding PVP in the blend, but thermal stability of the complex is higher than that of the blends as reflected by the higher T_d. Both FTIR and high-resolution solid state NMR show strong hydrogen bonding between PAA and PVP by showing significant chemical shift. The T_1ρ(H) measurement shows that the homogeneity scale for the blend is at ∼20 Å and that for the complex is ∼15 Å.     

Formation of polymer-polymer complexes and blends in the system poly(acrylic acid)-poly(vinyl methyl ether)

The formation of a 1:1 polymer-polymer complex from poly(acrylic acid) and poly(vinyl methyl ether) has been detected by viscosity measurements in aqueous solution, and the glass transition temperature of the isolated complex has been determined. Infrared spectroscopy indicates that specific hydrogen bonding occurs between the components of the complex. Miscible blends of the two polymers can also be formed (at all compositions) and, although hydrogen bonding occurs, the structures of the blends are likely to be dissimilar to that of the complex.     

Miscibility and crystallization of poly(ethylene succinate)/poly(vinyl phenol) blends

Miscibility of biodegradable poly(ethylene succinate) (PES)/poly(vinyl phenol) (PVPh) blends has been studied by differential scanning calorimetry (DSC) in this work. PES is found to be miscible with PVPh as shown by the existence of single composition dependent glass transition temperature over the entire composition range. Spherulitic morphology and the growth rates of neat and blended PES were investigated by optical microscopy (OM). Both neat and blended PES show a maximum growth rate value in the crystallization temperature range of 45-65 °C, with the growth rate of neat PES being higher than that of blended PES at the same crystallization temperature. The overall crystallization kinetics of neat and blended PES was also studied by DSC and analyzed by the Avrami equation at 60 and 65 °C. The crystallization rate decreases with increasing the temperature for both neat and blended PES. The crystallization rate of blended PES is lower than that of neat PES at the same crystallization temperature. However, the Avrami exponent n is almost the same despite the blend composition and crystallization temperature, indicating that the addition of PVPh does not change the crystallization mechanism of PES but only lowers the crystallization rate.     

Crystallization kinetics and morphology of poly(butylene succinate)/poly(vinyl phenol) blend

Biodegradable crystalline poly(butylene succinate) (PBSU) can form miscible polymer blends with amorphous poly(vinyl phenol) (PVPh). The isothermal crystallization kinetics and morphology of neat and blended PBSU with PVPh were studied by differential scanning calorimetry (DSC), optical microscopy (OM), wide angle X-ray diffraction (WAXD), and small angle X-ray scattering (SAXS) in this work. The overall isothermal crystallization kinetics of neat and blended PBSU was studied with DSC in the crystallization temperature range of 80-88 °C and analyzed by applying the Avrami equation. It was found that blending with PVPh did not change the crystallization mechanism of PBSU, but reduced the crystallization rate compared with that of neat PBSU at the same crystallization temperature. The crystallization rate decreased with increasing crystallization temperature, while the crystallization mechanism did not change for both neat and blended PBSU irrespective of the crystallization temperature. The spherulitic morphology and growth were observed with hot stage OM in a wide crystallization temperature range of 75-100 °C. The spherulitic morphology of PBSU was influenced apparently by the crystallization temperature and the addition of PVPh. The linear spherulitic growth rate was measured and analyzed by the secondary nucleation theory. Through the Lauritzen-Hoffman equation, some parameters of neat and blended PBSU were derived and compared with each other including the nucleation parameter (K_g), the lateral surface free energy (σ), the end-surface free energy (σ_e), and the work of chain folding (q). Blending with PVPh decreased all the aforementioned parameters compared with those of neat PBSU; however, the decrease extent was limited. WAXD result showed that the crystal structure of PBSU was not modified after blending with PVPh. SAXS result showed that the long period of blended PBSU increased, possibly indicating that the amorphous PVPh might reside mainly in the interlamellar region of PBSU.     

Glass polyalkenoate dental cements based on physical blends of poly(acrylic acid) and poly(vinyl phosphonic acid)

Physical blends of spray-dried poly(acrylic acid), PAA, with poly(vinyl phosphonic acid), PVPA, have been prepared and used in experimental dental cements by mixing them with basic sub-45 μm acid-degradable fluoroaluminosilicate glass powders and adding water. The effect of varying the ratio of PAA to PVPA, of altering the molar mass of PAA, and of using glasses of differing basicity have been investigated. The compressive strengths of the best of the cements formed from these blends were comparable to those formed from the individual polyacids, i.e. about 160 MPa.     

Poly(butylene succinate)/poly(vinyl phenol) blends. Part 1. Miscibility and crystallization

Miscibility has been investigated in blends of poly(butylene succinate) (PBSU) and poly(vinyl phenol) (PVPh) by differential scanning calorimetry in this work. PBSU is miscible with PVPh as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer–polymer interaction parameter, obtained from the melting depression of PBSU using the Nishi–Wang equation, is composition dependent, and its value is always negative. This indicates that PBSU/PVPh blends are thermodynamically miscible in the melt. Preliminary morphology study of PBSU/PVPh blends was also studied by optical microscopy (OM). OM experiments show the spherulites of PBSU become larger with the PVPh content, indicative of a decrease in the nucleation density, and the coarseness of PBSU spherulites increases too with increasing the PVPh content in the blends.     

Bending behaviour of electroresponsive poly(vinyl alcohol)/poly(acrylic acid) semi‐interpenetrating network hydrogel fibres under an electric stimulus

Poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) composite fibres were prepared via solution spinning and subsequently, semi‐interpenetrating networks (SIPN) were obtained by crosslinking the fibres with glutaraldehyde. The hydrogel fibres exhibited bending behaviour under DC electric stimulation. The effects of a number of factors have been systematically studied, including the PAA content within the network, electric voltage imposed across the fibre, the fibre diameter, concentration of the crosslinking agent, pH and ionic strength of the bath solution. Our experimental results show a stable reversibility of bending behaviour under the applied electric field. The degree of bending at equilibrium and the bending speed of the hydrogel fibre increased with the intensity of the applied electric voltage and the PAA content having negatively charged ionic groups within the SIPN. The electroresponsive behaviour of the present SIPN hydrogel fibre was also affected by the aforementioned extrinsic factors. These observations are interpreted in terms of fibre stiffness, fixed charge density and swelling pressure, which depend on the hydrogel equilibrium states in different pH and ionic environments together with the electrochemical reactions under DC electric field. © 2002 Society of Chemical Industry     

Fabrication of tissue engineering scaffold from poly(vinylalcohol-co-ethylene)/poly(D,L-lactic-co-glycolic acid) blend: Miscibility,thermomechanical properties,and morphology

A series of poly(DL-lactide-co-glycolic acid) (PLGA) with poly(vinylalcohol-co-ethylene) (PEVAL) blends were prepared by solution casting method. The miscibility, thermal and mechanical properties have been investigated using FTIR, DSC, and DMA techniques. The miscibility of this pair of polymers throughout compositions was proved by these methods through the single T_g and the presence of interactions between the constituents. The TGA analysis revealed three degradation zones and no sensible enhancement in the thermal stability of PLGA was noted with addition of PEVAL content. The SEM analysis revealed that the draying method dramatically influence the surface morphology of copolymers and blend. The cross section micrograph of blend scaffold containing 50 wt% of PEVAL presents microcavities of diameter pores ranged between 70 and 170 µm interconnected and uniformly distributed in the polymer matrix.     

A mucoadhesive polymer prepared by template polymerization of acrylic acid in the presence of poly(vinyl alcohol) for mucosal drug delivery

The interpolymer complexes composed of PVA and PAA were prepared by template polymerization of acrylic acid in the presence of PVA with different molecular weights and degrees of saponification. The carbonyl absorption band of the PAA in the PAA/PVA interpolymer complexes was shifted to a lower wavenumber due to H‐bonding between the carboxyl group of PAA and the hydroxyl group of PVA. The swelling ratio and the degree of dissolution of the PVA/PAA interpolymer complexes were dependent on the pH of the medium, the molecular weight, and the degree of saponification of the PVA. The release rate of a model drug, lidocaine, from the complexes decreased with increasing degree of saponification of the PVA due to the lower swelling degree of the complex. The adhesive force of the PVA/PAA interpolymer complexes with a plastic plate (poly propylene) was stronger than that of the commercial Carbopol 971P. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 327–331, 2004     

Miscibility and interactions in poly(methylthiomethyl methacrylate)/poly(vinyl alcohol) blends

Poly(methylthiomethyl methacrylate) (PMTMA) is miscible with poly(vinyl alcohol) (PVA) over the whole composition range as shown by the existence of a single glass transition temperature in each blend. The interaction between PMTMA and PVA was examined by Fourier transform infrared spectroscopy, solid-state nuclear magnetic resonance spectroscopy and X-ray photoelectron spectroscopy. The interactions mainly involve the hydroxyl groups of PVA and the thioether sulfur atoms of PMTMA, and the involvement of the carbonyl groups of PMTMA in interactions is not significant. The measurements of proton spin-lattice relaxation time reveal that PMTMA and PVA do not mix intimately on a scale of 1-3 nm, but are miscible on a scale of 20-30 nm. In comparison, we have previously found that PMTMA is miscible with poly(p-vinylphenol) and the two polymers mix intimately on a scale of 1-3 nm.     

Miscibility of poly(vinyl alcohol)/polyacrylamide blends before and after gamma irradiation

Films of polymer blends having various contents of poly(vinyl alcohol) (PVA) and polyacrylamide (PAM) were prepared by the solution casting technique using water as a common solvent. The thermal, mechanical and morphological properties of these blends before and after exposure to various doses of gamma radiation, up to 100 kGy, have been investigated. The visual observation and reflectance measurements show that PVA/PAM blends are miscible over a wide range of composition. Moreover, the differential scanning calorimetry (DSC) thermograms show only a single glass transition temperature (T_g), but not those of PVA or PAM homopolymers, giving further support to the complete compatibility of such blends. The T_g of PVA/PAM blends decreases with increasing content of PAM but increases after exposure to gamma irradiation, indicating the occurrence of crosslinking. These findings were demonstrated by the scanning electron micrographs of the fracture surfaces and the tensile mechanical properties. The TGA thermograms and percentage mass loss at different decomposition temperatures show that unirradiated PVA homopolymer possesses higher thermal stability than PAM homopolymer and their blends within the heating temperature range investigated, up to 250 °C. An opposite trend is observed within the temperature range 300–500 °C. In general, the thermal stability of homopolymers or their blends improves slighly after exposure to an irradiation dose of 100 kGy. These findings are clearly confirmed by the calculated activation energies of the thermal decomposition reaction of the homopolymers and the blends. © 2003 Society of Chemical Industry     

Miscibility and crystallization behavior of poly(ether ether ketone ketone)/poly(ether imide) blends

The miscibility and crystallization behavior of poly(ether ether ketone ketone) (PEEKK)/poly(ether imide) (PEI) blends prepared by melt‐mixing were investigated by differential scanning calorimetry. The blends showed a single glass transition temperature, which increased with increasing PEI content, indicating that PEEKK and PEI are completely miscible in the amorphous phase over the studied composition range (weight ratio: 90/10–60/40). The cold crystallization of PEEKK blended with PEI was retarded by the presence of PEI, as is apparent from the increase of the cold crystallization temperature and decrease of the normalized crystallinity for the samples anealed at 300°C with increasing PEI content. Although the depression of the apparent melting temperature of PEEKK blended with PEI was observed, there was no evidence of depression in the equilibrium melting temperature. The analysis of the isothermal crystallization at 313–321°C from the melt of PEEKK/PEI (100/0, 90/10, and 80/20) blends suggested that the retardation of crystallization of PEEKK is caused by the increase of the crystal surface free energy in addition to the decrease of the mobility by blending PEI with a high glass transition temperature. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 769–775, 2001     

Preparation of poly(acrylic acid)/poly(vinyl alcohol) membrane for the facilitated transport of CO2

Poly(acrylic acid) (PAA)/poly(vinyl alcohol) (PVA) membrane was prepared for the facilitated transport of CO₂. The carrier of CO₂ was monoprotonated ethylenediamine and was introduced in the membrane by ion exchange. The ion‐exchange capacity of the membrane was 4.5 meq/g, which was much higher than that of the Nafion 117 membrane. The membrane was highly swollen by the aqueous solution. Much higher selectivity of CO₂ over N₂ and higher CO₂ permeability were obtained in the PAA/PVA membrane than in the Nafion membrane because of the higher ion‐exchange capacity and solvent content. The highest selectivity was more than 1900 when the CO₂ partial pressure in the feed gas was 0.061 atm. Effects of ion‐exchange capacity, membrane thickness, and annealing temperature in conditions of membrane preparation on membrane performance were investigated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 936–942, 2001     

Enhanced oxygen‐barrier and water‐resistance properties of poly(vinyl alcohol) blended with poly(acrylic acid) for packaging applications

To enhance the oxygen‐barrier and water‐resistance properties of poly(vinyl alcohol) (PVA) and expand its food packaging applicability, five crosslinked poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) blend films were prepared via esterification reactions between hydroxyl groups in PVA and carboxylic acid groups in PAA. The physical characteristics of the blends, including the thermal, barrier, mechanical and optical properties, were investigated as a function of PAA ratio. With increasing PAA content, the crosslinking density was significantly increased, resulting in changes in the chemical structure, morphology and crystallinity of the films. The oxygen transmission rate of pure PVA decreased from 5.91 to 1.59 cc m^?1 day^?1 with increasing PAA ratio. The water resistance, too, increased remarkably. All the blend films showed good optical transparency. The physical properties of the blend films were strongly correlated with the chemical structure and morphology changes, which varied with the PAA content. © 2016 Society of Chemical Industry     

Drug release behavior of electrical responsive poly(vinyl alcohol)/poly(acrylic acid) IPN hydrogels under an electric stimulus

The electrically modulated properties of interpenetrating polymer networks (IPN) composed of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAAc) under electric field were investigated for drug delivery systems. PVA/PAAc IPNs with various compositions were synthesized by a sequential method, that is, ultraviolet polymerization of AAc in the mixture of PVA and aqueous AAc monomer solution, followed by a freeze‐thawing process to prepare elastic hydrogels. The amount of loaded drug significantly increased with the content of PAAc containing ionizable groups in IPN. The amount of introduced ionic drug (cefazoline) was greater than that of the nonionic drug (theophylline). Release behaviors of drug molecules from negatively charged PVA/PAAc IPN were switched on and off in a pulsatile pattern depending on the applied electric stimulus. The released amount and the release rate of drug were influenced significantly by the applied voltage, ionic group contents in IPN, ionic properties of drug solute, and the ionic strength of release medium. In addition, the ionic properties of drug molecules dramatically affected release behaviors, thus the release of ionic drug was much more enhanced than that of the nonionic drug. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1752–1761, 1999     

Swelling and morphological properties of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) hydrogels in solution with high salt concentration

Understanding the swelling properties of hydrogels and how they affect the hydrogel's morphology is of fundamental importance in the development of hydrogel-based artificial muscles, bio-actuators, sensors and other devices. In this paper, the swelling behavior of PVA-PAA hydrogel films in saline water and in buffer solutions of different pH values was investigated. It was observed that the swelling factor of the hydrogel decreases when the ionic strength of the solvent solution increases. Scanning Electron Microscopy (SEM) revealed structures with different pore shapes and sizes depending on the type of solution used for hydration. In saline water, Energy Dispersive X-Ray (EDS) analysis indicated the formation of NaCl crystals within the polymeric network. Finally, the PVA-PAA hydrogel was used as an actuator to strain a fiber Bragg grating sensor, thus providing an indirect measurement of the pH value of the surrounding solution.     

Properties of mineral filled poly(lactic acid)/poly(methyl methacrylate) blend

This study examines the influence of three different minerals, that is, clay, calcium carbonate, and quartz on the physical, thermal, and mechanical properties of poly(lactic acid) (PLA)/poly(methyl methacrylate) blend. Rheological behavior and phase structure were initially studied by small-amplitude oscillatory shear rheology. Clay- and quartz-filled materials presented an increase in viscosity at low frequency associated with the presence of a yield stress. However, this behavior was not observed for calcium carbonate filled materials due to a matrix degradation effect. To elucidate this aspect, thermal stability and thermal properties were examined by thermogravimetric analysis and differential scanning calorimetry, showing that calcium carbonate promotes degradation of the PLA phase. No nucleating effect was observed in the presence of the minerals. Dynamical mechanical analysis and mechanical characterization revealed an increase of the overall softening temperature and, a reinforcing effect for clay- and quartz-based composites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46927.     

Poly(vinyl alcohol) and poly(vinyl amine) blend membranes for isopropanol dehydration

Blended membranes of hydrophilic polymers poly(vinyl alcohol) (PVA) and poly(vinyl amine) (PVAm) were prepared and crosslinked with glutaraldehyde. The prepared membranes were characterized using infrared (attenuated total reflection mode) spectroscopy, differential scanning calorimetry, X‐ray diffractometry, and scanning electron microscopy measurements. Pervaporation performances of the membranes were evaluated for the separation of water‐isopropanol (IPA) mixtures. As the PVAm content increased from PVAm0 to PVAm1.5, the flux through a 70 μm film increased from 0.023 to 0.10 kg/m² h at an IPA/water feed ratio of 85/15 at 30 °C. The driving force for permeation of water increased due to the temperature but it has no effect on IPA permeation. Activation energies for the permeation of IPA and water were calculated to be 17.11 and 12.46 kJ/mol, respectively. Controlling the thickness of the blend membrane could improve the permeation flux with only a marginal reduction in the separation factor. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45572.     

Supercritical CO2‐assisted synthesis of poly(acrylic acid)/nylon1212 blend

PAA/nylon1212 blend was prepared using supercritical CO₂ as substrate‐swelling agent and monomer/initiator carrier. Both supercritical CO₂/nylon1212 binary system and SC CO₂/monomer/nylon1212 ternary system have been studied. Virgin nylon1212 and blends were characterized through differential scanning calorimetry (DSC), infrared spectroscopy (IR), and scanning electron microscopy (SEM). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2040–2044, 2003     

The effect of addition of poly(propylene‐g‐acrylic acid) on the morphology of poly(vinyl methylether) and isotactic polypropylene blend

The interfacial adhesion of blend of isotactic polypropylene/poly(vinyl methylether) (i‐PP/PVME) has been improved by the addition of poly(propylene‐g‐acrylic acid) (PP‐g‐AA) as a compatibilizing agent. The phase morphologies of the blends are investigated by optical microscopy (OM) and lateral force microscopy (LFM). The i‐PP/PVME (80/20) blend with no addition of PP‐g‐AA from extrusion process shows a coarse morphology with the dispersed domain size as large as several micrometers; After the addition of 2.5% PP‐g‐AA in the blends, the dispersed PVME domain size decreases greatly. The addition of 5% PP‐g‐AA results in a homogeneous morphology. The blending of PP‐g‐AA with PVME reduces the crystallization temperature of PP‐g‐AA, which is different from that of blending i‐PP with PVME. The increase of the interfacial adhesion is attributed to the specific intermolecular interaction between the acrylic acid group of PP‐g‐AA and the ether group of PVME. The specific interaction is studied by Fourier transform infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4098–4103, 2006