气固流化床中侧向射流穿透深度的研究

本文以小米和两种硅胶为物料，在314×25mm的二维射流流化床中，用摄像法研究侧向射流穿透深度，并得到了关联式，误差小于25％．当射流倾角变化范围不大、并忽略射流位置的影响时，可以得到简化公式，误差小于40％使用基于对流体模型的计算机程序进行模拟，分析了射流产生的机理，研究了射流气速、直径、倾角和位置对射流穿透深度的影响．模拟值和实验值较吻合．     

气固流化床中倾斜分布板上射流深度的研究

在二维流化床中,用摄像法研究了锥形分布板上射流。实验中发现,锥形分布板上射流可分为I类射流和II类射流,60°分布板上射流都是I类射流,45°分布板上观察到了II类射流,随着条件的变化射流类型也发生了改变。射流的类型与分布板角度、孔速、颗粒性质、孔的位置有关。相同气速下,0°(水平)分布板上的射流深度要大于45°和60°分布板。床层高度对射流深度的影响可以忽略。对实验数据进行拟合得到了锥形分布板上单孔射流深度关联式。     

气固流化床内射流穿透深度的CFD模拟及其实验验证

在经典的Gidaspow无黏性双流体模型中考虑离散颗粒对流体和固体动量守恒方程的影响后,建立了一个具有模拟大规模流化床内气固两相流体动力学特性潜在优势的简化数学模型。在CFX4.4商业化软件平台上通过增加用户自定义子程序考察了二维气固流化床(高2.00 m、宽0.30 m)内射流气速、喷嘴尺寸、环隙气速和静床高度对射流穿透深度的影响,并以树脂颗粒(粒径670 μm、密度1474 kg·m^-3)为研究对象在厚度为0.025 m的矩形床内进行了对比实验。结果表明,选取空隙率为0.8的等高线作为射流边界比较合适;射流穿透深度随射流气速或射流喷口尺寸的增加而增大;射流周围环隙气速由0变到最小流化速度时,射流穿透深度随环隙气速增加而增大,在最小流化速度时达到最大值,然后随环隙气速增加单调减小,当环隙气速大于2.5倍最小流化速度时,射流穿透深度减小程度变缓;在相同射流气速下射流穿透深度随着静床高度的增加而减小,静床高度对射流穿透深度的影响随着射流气速增加呈现扩大的趋势。     

大型单射流流化床的流动特性

在φ500mm×8000mm的大型单射流半圆形流化床中,采用内径为42mm的半圆形射流管,以小米为实验物料,利用摄像法研究了射流气速、静床高度与射流深度的关系,得出了射流深度的定量关联式．藉PC—4光导纤维测浓仪,研究了大型射流流化床径向、轴向空隙率分布规律,最后得出了射流区各点空隙率分布的定量关系式．     

半圆流化床中垂直双射流喷射深度及气体合并行为

在内径５００ｍｍ的半圆形流化床中,考察了２个内径４２ｍｍ的半圆喷口的射流深度及气体合并行为．结果表明,双射流条件下每个单射流的喷射深度与喷口间距无关,进一步证明了二维流化床中得到的研究结果．给出了一个适用范围较宽的射流深度经验关联式．在双射流相互干扰的研究中,发现存在两种合并特征,即射流区合并及射流区外的气泡合并,并就这两种合并的判据、合并高度与操作及几何条件的关系进行了讨论．     

供气系统对流化床气-固流动行为的影响简

流态化技术在过程工业中广泛应用。供气系统是流化床裂置系统的重要组成部分之一，本文总结了供气系统对流化床内气-固流动行为的影响，包括耦合作用形式、气泡流形式与相互作用，并讨论了气体分布板对流化床流动行为的影响，包括分布板气体流率的不均匀性、分布板进风方向的影响和分布板开孔率的影响。最后展望今后的研究重点方向。     

多组分射流床中的射流深度

采用多路毕托管、电磁阀、微压传感器检测技术，考察了气固射流流化床中GeldartB、D类的单一物料及混合物的射流深度．指出物料的平均密度或粒径的增加都会造成射流深度的降低；得到的包括气团惯性准数在内的经验关联式能成功地预测多组分床层的射流深度．     

基于双流体模型的流化床模拟

从单相流体力学中描述气体流动的Navier-Stokes方程和单颗粒运动的Newton方程出发,使用比较严格的体积平均法推导出描述气固两相宏观流动的模型方程组并设法确定了模型参数,把该方程组加以简化,能得到Gidaspow、Blake和Davidson等人的模型方程,初步证明了模型的正确性,求解使用了经本文改进的基于控制容积有限差分的IPSA方法,编制了通用程序,模拟了二维射流流化床中浓密气固两相的流动,并计算出射流的穿透深度。     

喷动流化床流动特性数值模拟

为了捕捉喷动流化床中微观层次上的颗粒运动信息,建立了基于CFD的二维非稳态喷动流化床欧拉-欧拉两相流模型。分析了不同流化气速对喷动流化床气固流动特性的影响,即不同工况下的炉内压力降、颗粒浓度、床内空隙率分布、气体速度分布和固体颗粒速度分布。数值模拟研究结果表明:随流化气速的增大,压降和炉内平均空隙率逐渐增大,密相床层高度逐渐增加,沿着轴向方向的气体流量增大,喷动气的射流深度逐渐增加,同时射流半径也逐渐增加。     

灰熔聚气化装置冷模射流流化床的研究

概述了灰熔聚冷模气固射流流化床的研究现状，内容主要包括：射流形成的条件及流型划分、射流深度、射流势能区、颗粒混合及运动、空隙率分布、气泡行为、分离特性；并预测了今后的研究趋势。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。