无直流电压传感器的单相APFC变换器

文章对一种只检测交流输入电压而不需要检测输出直流电压的简化单相PFC变换器进行了理论分析和研究。在构建控制电路时,不需要常规PFC变换器中的输出电压传感器和输入电流传感器。PFC变换器的主电路为整流电路的直流侧接一级Boost电路。在控制电路中,使用电感L、等效负载电阻Rd等电路参数产生正弦电流波形基准,输出电压直接由控制量Kd(=Ed/Ea)来调节。通过控制,可以得到恒定的直流输出电压和与交流输入电压同相位的正弦电流波形。仿真结果证明了该变换器的可行性。     

单相两级有源功率因数校正变换器的研究

文中对两级有源功率因数校正变换器进行研究,设计了一台510W两级式开关电源。该电源前级采用平均电流控制的Boost型PFC电路,实现功率因数校正;后级采用不对称半桥型DC／DC变换器,实现开关管的零电压开关。控制电路采用PFC／PWM复合控制芯片ML4824,缩小电源体积。通过实验证实该开关电源具有高功率因数与高效率的特点。     

A new modulation strategy for a buck-boost input AC/DC converter

This paper presents a novel modulation strategy for a power factor corrected (PFC), isolated AC/DC converter derived from the integration of a nonisolated, two switch buck-boost AC/DC converter with an isolated dual active bridge DC/DC converter (2SBBDAB). This strategy, termed discontinuous leading/trailing edge (DLTE) modulation, serves to maximize the duty cycle of the input switch while keeping the current in the buck-boost inductor discontinuous. Hence, the crest factors of the currents in the switching devices are minimized, the input switch is turned on at zero current and the zero-voltage switching ranges of the bridge switches are unaffected by the integration. A conventional isolated, PFC AC/DC converter typically consists of a boost converter cascaded with a forward converter. The ratings required of the power switching devices of the 2SBBDAB employing the DLTE modulation strategy are similar to those required of the conventional design for wide line voltage operation. However, the 2SBBDAB converter has higher line voltage surge immunity than that of the conventional design and, unlike the conventional design, it has inherent inrush current limiting. The DLTE modulation strategy may be applied to the family of converters composed of the two switch buck-boost integrated with half and full-bridge forward converters     

A soft-switching mode rectifier with power factor correction andhigh frequency transformer link

This paper presents a soft-switching mode rectifier (SSMR) consisting of a power factor correction zero-voltage-transition-pulse-width-modulated (PFC ZVT-PWM) converter and a high-frequency transformer-coupled DC/DC zero voltage switching clamped voltage (ZVS-CV) converter. An easily implemented ZVT soft-switching mechanism is developed to reduce the switching losses and stresses of the power switches in the PFC ZVT-PWM converter. The operations of the proposed SSMR in various modes are analyzed in detail and the associated governed equations are derived. Then accordingly, a quantitative design procedure is developed to find the values of soft-switching circuit components. In the control aspect, the dynamic model of the SSMR is derived and a current waveform controller is designed, such that sinusoidal line current with low harmonics and near unity power factor is obtained. Under this condition, a voltage controller is also designed for yielding good DC output voltage control characteristics. Validity of the designed SSMR is verified experimentally     

A digital power factor correction (PFC) control strategy optimized for DSP

A predictive algorithm for digital control power factor correction (PFC) is presented in this paper. Based on this algorithm, all of the duty cycles required to achieve unity power factor in one half line period are calculated in advance by digital signal processors (DSP). A boost converter controlled by these precalculated duty cycles can achieve sinusoidal current waveform. One main advantage is that the digital control PFC implementation based on this control strategy can operate at a high switching frequency which is not directly dependent on the processing speed of DSP. Input voltage feed-forward compensation makes the output voltage insensitive to the input voltage variation and guarantees sinusoidal input current even if the input voltage is distorted. A prototype of boost PFC controlled by a DSP evaluation board was set up to implement the proposed predictive control strategy. Both the simulation and experimental results show that the proposed predictive strategy for PFC achieves near unity power factor.     

An active power factor correction technique for three-phase dioderectifiers

A novel active power factor correction method for power supplies with three-phase front-end diode rectifiers is proposed and analyzed. The implementation of this method requires the use of an additional single switch boost chopper. The combined front-end converter draws sinusoidal AC currents from the AC source with nearly unity input power factor while operating at a fixed switching frequency. It is shown that when the active input power factor correction stage is also used to regulate the converter DC bus voltage, the converter performance can improve substantially in comparison with the conventional three-phase AC-to-DC converters. These improvements include component count reduction, simplified input synchronization logic requirements, and smaller filter refractive components. Theoretical results are verified experimentally. The proposed method has the disadvantage of substantially increasing the current stresses of the switching devices and the high-frequency ripple content of the prefiltered AC input currents     

基于BOOSt结构下不连续导电模式的PFC电路

采用现代高频功率变换技术的有源功率因数校正（Power Factor Corrector,PFC)技术是解决高频开关变换器谐波污染的有效手段。与传统的PFC电路相比，有源PFC电路的输入电流接近正弦波且与输与电压同相位，能有效抑制电流波形畸变和谐波，因此避免了对同一电网设施的干扰。在PFC电路中，Boost变换器是研究和应用得最多的一种变换器。本文着重分析了Boost电路在不连续导电模式状态下，PFC电路的临界条件，对实际电路结构的设计有很好的指导意义。     

基于有源功率因数校正的高功率因数电源设计

构建有源功率因数校正（APFC）的高功率因数直流电源。该系统采用TI公司专用APFC整流控制芯片UCC28019作为控制核心,构成电压外环和电流内环的双环控制。其中内环电流环作用是使网侧交流输入电流跟踪电网电压的波形与相位;外环电压环为输出直流电压控制环。外环电压调节器的输出控制内环电流调节器的增益,使输出直流电压稳定。系统采用ATmega16单片机进行监控,完成输出电压的可调以及输入功率因数、输出电压、输出电流等的实时测量与显示和输出过流保护等功能。实测表明,系统性能指标完全达到或超过设计要求。     

Voltage and current stress reduction in single-stage power factorcorrection AC/DC converters with bulk capacitor voltage feedback

Single-stage power factor correction (PFC) AC/DC converters integrate a boost-derived input current shaper (ICS) with a flyback or forward DC/DC converter in one single stage. The ICS can be operated in either discontinuous current mode (DCM) or continuous current mode (CCM), while the flyback or forward DC/DC converter is operated in CCM. Almost all single-stage PFC AC/DC converters suffer from high bulk capacitor voltage stress and extra switch current stress. The bulk capacitor voltage feedback with a coupled winding structure is widely used to reduce both the voltage and current stresses in practical single-stage PFC AC/DC converters. This paper presents a detailed analysis of the bulk capacitor voltage feedback, including the relationship between bulk capacitor voltage, input current harmonics, voltage feedback ratio, and load condition. The maximum bulk capacitor voltage appears when the DC/DC converter operates at the boundary between CCM and DCM. This paper also reveals that only the voltage feedback ratio determines the input current harmonics under DCM ICS and CCM DC/DC operation. The theoretical prediction of the bulk capacitor voltage as well as the predicted input harmonic contents is verified experimentally on a 60 W AC/DC converter with universal-line input     

Characteristics of load resonant converters operated in ahigh-power factor mode

The performance of the parallel resonant power converter and the combination series/parallel resonant power converter (LCC converter) when operated above resonance in a high power factor mode are determined and compared for single phase applications. When the DC voltage applied to the input of these converters is obtained from a single phase rectifier with a small DC link capacitor, a relatively high power factor inherently results, even with no active control of the input line current. This behavior is due to the pulsating nature of the DC link and the inherent capability of the converters to boost voltage during the valleys of the input AC wave. With no active control of the input line current, the power factor depends on the ratio of operating frequency to tank resonant frequency. With active control of the input line current, near-unity power factor and low-input harmonic currents can be obtained     

A novel voltage sensorless control technique for a bidirectional AC/DC converter

A novel voltage sensorless control technique for a bidirectional AC/DC converter is presented. Only a single current sensor that measures the inductor current is needed in the whole system. The sensed inductor current is used for two functions. The first one is for shaping the current waveform at the AC side and the second one is for deriving the inductor voltage by determining the rate of change of the inductor current. The AC-side and DC-side voltages, which are used for AC current synchronization and DC voltage regulation, respectively, are obtained by extracting the envelopes of the derived inductor voltage. Apart from reducing the number of sensing elements, the proposed method has additional advantages of: (1) inherent electrical isolation and reducing noise coupling between the power circuit and the controller; (2) wide operating range. Design criteria for the differentiator and the envelope detector circuit has been described. The applicability of the proposed method is verified with the experimental results of a laboratory prototype.     

Asymmetrical pulse-width-modulated resonant DC/DC convertertopologies

This paper presents asymmetrical pulse-width-modulated (APWM) DC/DC resonant converter topologies that exhibit near-zero switching losses while operating at constant and very high frequencies. The converters include a bridged chopper to convert the DC input voltage to a high-frequency unidirectional AC voltage, which in turn is fed to a high-frequency transformer through a resonant circuit. The bridged chopper has two switches that alternately conduct. The duty cycles of the conduction of the switches are complementary with one another and are varied to control the output voltage. Three resonant circuit configurations suitable for this type of control are presented. Frequency domain analysis of the converter is given, and performance characteristics are presented. Experimental results for a 48-5 V, 30 W converter show an efficiency of 88% at a constant operating frequency of 1 MHz     

A new passive 28-step current shaper for three-phase rectification

A new passive 28-step current shaper for three-phase rectification is proposed in this paper. With a phase-shifting transformer on the AC side and six interphase transformers on the DC side, per-phase input current can be shaped into a 28-step sinusoidal waveform. The total harmonic distortion of AC input currents obtained is 6.53%, lower than one-half of that in a conventional 12-pulse converter. The transformer voltampere rating is also lowered down to one-fifth of that in a 12-pulse converter. A 2 kW experiment is performed to verify the proposed circuit.     

LIMITATION OF SOFT-SWITCHING TECHNIQUE IN AC/DC POWER CONVERTER'S EFFICIENCY IMPROVEMENT

Soft-switching techniques are attractive to unity-power-factor AC/DC converter in the view of the size reduction and EMI suppression. A soft-switched boost PFC converter has been studied based on its topology analysis, PSIM simulation and circuit experiment. A special limitation of soft-switching techniques has been found in their AC/DC applications.     

A Very Simple Control Strategy for Power Factor Correctors Driving High-Brightness LEDs

This paper presents a new control strategy for power factor correctors (PFCs) that are used to drive high-brightness LEDs. This control strategy is extremely simple and is based on the use of a conventional peak-current-mode controller with a suitable selection of the compensation ramp waveform. Neither an analog multiplier nor an input voltage sensor is needed to achieve quasi-sinusoidal line waveforms at nominal conditions and full load. If the converter belongs to the flyback family (flyback, buck–boost, SEPIC, Cuk and Zeta), the line waveform appears notably distorted if the compensation function is a linear ramp, but becomes almost sinusoidal if the linear ramp is substituted by a properly chosen exponential function. The line waveform is slightly distorted when the load varies or when the converter works under either overvoltage or undervoltage conditions. However, the waveform maintains a very high power factor (PF) even under these conditions. Moreover, the line current is cycle-by-cycle-controlled due to the peak-current-mode control, and hence, the input-current feedback loop is extremely fast, thereby allowing this type of control to be used with high-frequency lines (above 400 Hz).      

Unified constant-frequency integration control of active powerfilters-steady-state and dynamics

An active power filter (APF) is a device that is connected in parallel to and cancels the reactive and harmonic currents from a group of nonlinear loads so that the resulting total current drawn from the AC mains is sinusoidal. This paper presents a unified constant-frequency integration (UCI) APF control method based on one-cycle control. This method employs an integrator with reset as its core component to control the pulse width of an AC-DC converter so that its current draw is precisely opposite to the reactive and harmonic current draw of the nonlinear loads. In contrast to previously proposed methods, there is no need to generate a current reference for the control of the converter current, thus no need for a multiplier and no need to sense the AC line voltage, the APF current, or the nonlinear load current. Only one AC current sensor is used to sense the AC main current and one DC voltage sensor is used to sense the DC capacitor voltage. The control method features constant switching frequency operation, minimum reactive and harmonic current generation, and simple analog circuitry. It provides a low cost and high performance solution for power quality control. Steady-state and dynamic study is presented in this paper. Design example is given using a two-level AC-DC boost topology. A prototype was developed to demonstrate the performance of the proposed APF. This control method is generalized to control a family of converters that are suitable for APF applications. All findings are supported by experiments and simulation     

A novel ZCS-PWM power-factor preregulator with reduced conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the active switches and zero-voltage switching in the passive switches. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Nine transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 50 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.3% and power factor over 0.99 has been measured. Analysis, design, and the control circuitry are also presented in this paper.     

A novel three-phase utility interface minimizing line currentharmonics of high-power telecommunications rectifier modules

Based on the combination of a three-phase diode bridge and a DC/DC boost converter, a new three-phase three-switch three-level pulsewidth modulated (PWM) rectifier system is developed. It can be characterized by sinusoidal mains current consumption, controlled output voltage, and low-blocking voltage stress on the power transistors. The application could be, e.g., for feeding the DC link of a telecommunications power supply module. The stationary operational behavior, the control of the mains currents, and the control of the output voltage are analyzed. Finally, the stresses on the system components are determined by digital simulation and compared to the stresses in a conventional six-switch two-level PWM rectifier system     

一种改善PFC变换器输入电流过零畸变的方法

功率因数校正（PFC）变换器普遍存在输入电流在输入电压过零点附近发生畸变的现象。文中详细分析了PFC变换器输入电流在输入电压过零点附近产生畸变的原因,指出了Boost PFC变换器的输入电流超前于输入电压是导致位移因数不为1和输入电流过零畸变的主要原因;提出了根据输入电流在输入电压过零时刻的值实时修正参考输入电压的初相角,以改善PFC变换器输入电流过零畸变的数字控制方法。仿真结果证明了文中所提出的方法的有效性,特别是在400Hz输入电压下有很好的效果。     

Limitation of soft-switching technique in AC/DC power converter’s efficiency improvement

Soft-switching techniques are attractive to unity-power-factor AC/DC converter in the view of the size reduction and EMI suppression. A soft-switched boost PFC converter has been studied based on its topology analysis, PSIM simulation and circuit experiment. A special limitation of soft-switching techniques has been found in their AC/DC applications. Sponsored by the Scientific Research Foundation for the Returned Overseas Chinese Scholars, Ministry of Education