(1 − x)CaTiO3–x(Li0.5Nd0.5)TiO3 for ultra-small dielectrically loaded antennas

Microwave (MW) dielectric ceramics based on the solid solution (1 ? x)CaTiO₃–x(Li_0.5Nd_0.5)TiO₃ (0.25 ≤ x ≤ 1.0) were prepared by conventional solid-state synthesis using the mixed oxide route. Compositions closest to zero τ_f (+65 ppm/°C) were obtained at x = 0.8 where ε_r = 110 and the microwave quality factor, Qf ₀ ? 2600 GHz for samples sintered at 1300 °C. To reduce the sintering temperature and compensate for any Li₂O loss during fabrication, ≤0.5 wt% 0.5Li₂O–0.5B₂O₃ was added as a sintering aid in the form of raw oxides (LBR) and also as a pre-reacted glass (LBG). 0.5 wt% LBR was the most effective, reducing the temperature to achieve optimum density by ~50 °C with no significant deterioration of microwave properties (ε_r = 115, τ_f = +65 ppm/°C and Qf ₀ ? 2500 GHz). The high permittivity and relatively low sintering temperatures (1250 °C) are ideal for the development of low cost ultra-small dielectric loaded antenna, assuming the system can be tuned closer to zero by fractionally increasing x.     

Microstructure and piezoelectric properties of lead-free 0.95(Na0.5K0.5)NbO3–0.05(Bi0.5K0.5)Zr1−x Ti x O3 ceramics

0.95(Na_0.5K_0.5)NbO₃–0.05(Bi_0.5K_0.5)Zr_1?x Ti _x O₃ (abbreviated as KNN–BKZT _x ) ceramics were prepared by the conventional solid state method, and the effect of the Ti content on the surface morphology, crystalline structure, and electrical properties of KNN–BKZT _x ceramics were mainly investigated. With the increase of Ti content, the temperature of the orthorhombic–tetragonal (O–T) phases transitions shifted to lower temperatures, and the O–T phase boundary of KNN–BKZT _x ceramics was identified in the composition with 0 ≤ x ≤ 0.3 at room temperature. It was considered that the piezoelectric properties of the ceramics were enhanced significantly owing to the more possible polarization states resulting from the coexistence of two phases. The ceramic with x = 0.2 exhibited optimum properties: d ₃₃ = 260 pC/N, k _p = 0.38, and T _C = 323 °C.     

Ferroelectric and piezoelectric properties of (1 − x) (Bi0.5Na0.5)TiO3–xBaTiO3 ceramics

Lead-free ceramics based on bismuth sodium titanate (Bi_0.5Na_0.5TiO₃, BNT)–barium titanate (BaTiO₃,BT) have been prepared by solid state reaction process. The (1?x)BNT–(x)BT (x = 0.01,0.03,0.05,0.07) ceramics were sintered at 1,150 °C for 4 h in air, show a pure perovskite structure. X-ray diffraction analysis indicates that a solid solution is formed in (1?x)BNT–(x)BT ceramics with presence of a morphotropic phase boundary (MPB) between rhombohedral and tetragonal at x = 0.07. Raman spectroscopy shows the splitting of (TO₃) mode at x = 0.07 confirming the presence of MPB region. The temperature dependence dielectric study shows a diffuse phase transition with gradual decrease in phase transition temperature (T_m). The dielectric constant and diffusivity increases with increase in BT content and is maximum at the MPB region. With the increase in BT content the maximum breakdown field increases, accordingly the coercive field (E_c) and remnant polarization (P_r) increases. The piezoelectric constant of (1 ? x)BNT–(x)BT ceramics increases with increase in BT content and maximum at x = 0.07, which is the MPB region. The BNT–BT system is expected to be a new and promising candidate for lead-free dielectric and piezoelectric material.     

Sr_(0.5)Ba_(0.5)TiO_3/La_(0.5)Sr_(0.5)CoO_3双层薄膜的微观结构

采用脉冲激光沉积法在(001)LaAlO_3衬底上制备了Sr_(0.5)Ba_(0.5)TiO_3/La_(0.5)Sr_(0.5)CoO_3薄膜,利用透射电子显微镜对薄膜的微观结构进行了研究。结果表明,底电极La_(0.5)Sr_(0.5)CoO_3在LaAlO_3衬底上外延生长并形成立方-立方取向关系。不同于块体结构,LSCO薄膜发生了结构转变,形成一种氧缺位有序调制结构。整个薄膜由大量取向畴组成,其中包含一些层错与反相畴界等缺陷。生长温度为500℃时,Sr_(0.5)Ba_(0.5)TiO_3薄膜为柱状多晶结构;当温度升高至820℃时,薄膜为缺陷较少的单晶结构。     

Effect of Te Substitution on (Tl0.5Pb0.5)Sr2(Ca1?x Te x )Cu2O7 (x=0.0 to 0.5) Superconductor

The (Tl_0.5Pb_0.5)Sr₂(Ca_1?x Te _x )Cu₂O_7??? (Tl-1212) superconductor for x=0.0 to 0.5 has been prepared and studied by a powder X-ray diffraction method, electrical resistance and AC susceptibility measurements. Most of the samples showed Tl-1212 as the major phase and Tl-1201 as the minor phases. Small amounts of Te substitution (x??0.3) maintained the formation of the Tl-1212 phase but larger amounts led to the formation of 1201 and an unknown impurity phase. The resistance versus temperature curve showed metallic behavior for all samples. The resistance versus temperature curves showed onset transition temperature ( $T_{\mathrm{c\ onset}}$ ) between 92 and 97 K. Our results indicated the combined effects of Te substitution, heating temperature and heating time on the formation and optimization of the (Tl_0.5Pb_0.5)Sr₂(Ca_1?x Te _x )Cu₂O₇ superconductor.     

Effect of bond valence on microwave dielectric properties of (1 − x)CaTiO3–x(Li0.5La0.5)TiO3 ceramics

The origins of microwave dielectric properties (1 ? x)CaTiO₃–x(Li_0.5La_0.5)TiO₃ (0.2 ≤ x ≤ 0.8) ceramics, prepared by a conventional solid-state reaction method, were investigated based on the theory of bond valence. The XRD and SEM results showed that complete solid solutions with orthorhombic perovskite structure were formed in the whole investigated compositional range. The dielectric constant (?_r), quality factor (Q × f) and temperature coefficient of resonant frequency (τ_f) were closely related to B-site, A-site and the difference between A-site and B-site bond valences of ABO₃ perovskite compounds, respectively. As x value increased from 0.2 to 0.8, the dielectric constant increased from 198.3 to 276.8, the Q × f value decreased from 4340 to 1880 GHz, and the τ_f value varied from +489.7 to ?178 ppm/°C. For practical applications, excellent microwave dielectric properties of ?_r = 245, Q × f = 2750 GHz and τ_f = +0.75 ppm/°C were obtained for 0.4CaTiO₃–0.6(Li_0.5La_0.5)TiO₃ ceramics.     

(0.84-x)Na_(0.5)Bi_(0.5)TiO_3-0.16K_(0.5)Bi_(0.5)TiO_(3-x)SrTiO_3系无铅压电陶瓷结构与电性能

采用固相法制备了Bi补偿的(0.84-x)Na0.5Bi0.5TiO3-0.16K0.5Bi0.5TiO3-x SrTiO3(简称NBTKBT-xST)无铅压电陶瓷,研究不同ST掺量对体系陶瓷的结构与电性能的影响规律。结果表明,在掺杂范围内(0≤x≤0.06),材料均能形成单一的钙钛矿固溶体结构。随着x的增加,陶瓷晶体结构逐渐由三方相向四方相过渡,且该体系的三方-四方准同型相界(MPB)位于0.03≤x≤0.04。在此组成区域内,体系陶瓷的铁电与压电性能较好,其中x=0.04时,材料的电性能较好:压电常数d33=156 pC/N,平面机电耦合系数k p=0.29,相对介电常数εr=1116,介质损耗tanδ=4.1%,剩余极化强度P r=30.5μC/cm2,矫顽场E c=23.9 kV/cm。介电温谱和变温电滞回线表明体系陶瓷在T d以上可能存在极性相与非极性相共存。     

Energy storage properties of (1 − x)(Bi0.5Na0.5)TiO3–xKNbO3 lead-free ceramics

In this study, a simple compound (1 ? x)(Bi_0.5Na_0.5)TiO₃–xKNbO₃ (x = 0 – 0.12) lead-free bulk ceramic was developed for high electric power pulse energy storage applications. The dielectric and ferroelectric properties of the ceramics were measured. The results illustrate that the energy storage density of the ceramics is enhanced by the addition of KNbO₃. The influence of applied electric field, temperature, and fatigue on the energy storage properties of the ceramics was evaluated for the composition-optimized (Bi_0.5Na_0.5)TiO₃–0.1KNbO₃ ceramic. The results demonstrate that (Bi_0.5Na_0.5)TiO₃–0.1KNbO₃ ceramic is a promising lead-free material for high power pulse capacitor applications. The excellent energy storage properties of the (Bi_0.5Na_0.5)TiO₃–0.1KNbO₃ ceramics are ascribed to the reversible relaxor–ferroelectric phase transition induced by the electric field.     

Effects of Co doping on microstructure and properties of (K0.5Na0.5)NbO3–LiSbO3–BiFe(1−x)Co x O3 lead-free piezoelectric ceramics

0.998 [(0.95(K_0.5Na_0.5)NbO₃–0.05LiSbO₃]–0.002BiFe_(1?x)Co _x O₃ (KNN–LS–BF_(1?x)C _x ) lead-free piezoelectric ceramics were prepared by conventional solid-state reaction method. The influences of Co content on the phase structure, microstructure, density and related electrical properties were investigated. The results reveal that the substitution of Co significantly improves the sinterability and the electrical properties of KNN–LS–BF_(1?x)C _x ceramics, sintered at a lower temperature of 1,030 °C, compared with that of KNN–LS–BF ceramics. With increasing x from 0 to 0.8, all samples show a pure perovskite structure, but the grain size increases continuously,and the porosity level reaches it’s lowest value at x = 0.2. The density ρ, piezoelectric constant d ₃₃, coupling factor k _p and dielectric constant ε _r increase with x up to 0.2, and then decrease with further increase in x value, but the variation of dielectric loss tan δ is opposite. The density and electrical properties achieve optimal value of ρ = 4.287 g/cm³, d ₃₃ = 276 pC/N, k _p  = 48 %, ε _r  = 1,284 and tan δ = 1.95 %, when x = 0.2. And Tc ≈ 340 °C at all the variation range of Co content.     

Reaction-sintering of lead-free piezoceramic compositions: (0.95 − x)Na0.5K0.5NbO3–0.05LiTaO3–xLiSbO3

Incorporation of LiSbO₃ into the lead-free piezoceramic composition 0.95Na_0.5K_0.5NbO₃–0.05LiTaO₃ produced a change from an orthorhombic to tetragonal crystal system in samples produced by reaction-sintering. The inferred limit of solid solution along the compositional join, (0.95 − x)Na_0.5K_0.5NbO₃–0.05LiTaO₃–xLiSbO₃, occurred at x ~ 0.06. Differential scanning calorimetry indicated broad peaks at temperatures associated with ferroelectric–paraelectric transitions. The transition temperatures decreased with increasing values of x, up to x = 0.06. Microstructures showed secondary grain growth; a slight decrease in grain-size with increasing LiSbO₃ modification was identified.     

Piezoelectric and dielectric properties of 0.98(Na0.5K0.5)NbO3–0.02Ba(ZrxTi(1−x))O3 ceramics

Lead-free 0.98(Na_0.5K_0.5)NbO₃–0.02Ba(Zr_xTi_(1?x))O₃ (0.98NKN–0.02BZT) ceramics with Zr contents were fabricated by a conventional mixed-oxide method. The results indicate that the Zr/Ti ratio significantly influences the structural, piezoelectric, dielectric, and ferroelectric properties of 0.98NKN–0.02BZT ceramics. For the 0.98NKN–0.02BZT (x = 0) ceramics sintered at 1090 °C, the bulk density increased as the Zr contents decreased and showed a maximum value at x = 0. The Curie temperature of the 0.98NKN–0.02BZT ceramics slightly decreased as the Zr contents increased. The dielectric constant, piezoelectric constant, and electromechanical coupling factor of samples were maximized at x = 0, which might be due to the increase in density. A high d₃₃ = 194 pC/N, k_p = 38% were obtained for the 0.98NKN–0.02BZT ceramics sintered at 1090 °C for 4 h.     

Glass-free LTCC microwave ceramic-Ca1−x(La0.5Na0.5)xWO4

The structure and microstructure of the Ca_1?x(La_0.5Na_0.5)_xWO₄ (0.1 ≤ x ≤ 1.0) ceramics were investigated using X-ray powder diffraction (XRD) and scanning electron microscopy (SEM) method. The microwave dielectric properties of the ceramics were studied with a network analyzer at the frequency of about 10–14 GHz. Continuous solid solutions Ca_1?x(La_0.5Na_0.5)_xWO₄ (0.1 ≤ x ≤ 1.0) with Scheelite structure (space group: I4₁/a) could be densified at 850 °C/2 h. The dielectric permittivity increased slightly with the increase in substitution amount. The Q × f value decreased with the increase of x up to x = 0.5, and then increased with further increase of x. The Q × f value increased when the sintering temperature increased from 850 to 950 °C for the x < 0.5 compositions, whereas it decreased with the increase in sintering temperature for the x > 0.5 compositions. The τ _f value changed a little with the variation of x. All samples exhibited negative τ _f values. Addition of 30 mol% TiO₂ to the x = 0.9 composition improved the τ _f to ?9.3 ppm/°C with ε_r = 14.4 and Q × f = 14,255 GHz after sintering at 850 °C/2 h. The chemical compatibility of Ca_0.1(La_0.5Na_0.5)_0.9WO₄ + 30 mol% TiO₂ composite with silver (Ag) powders was also investigated. The composite showed inert behavior with Ag when cofired at 875 °C for 2 h. However small amount of Na_0.86WO₃ impurity phase was detected in the co-fired specimen.     

Microstructure and microwave dielectric properties of xSm(Mg0.5Ti0.5)O3–(1 − x)Ca0.8Sr0.2TiO3 ceramics

xSm(Mg_0.5Ti_0.5)O₃–(1 ? x)Ca_0.8Sr_0.2TiO₃ (x = 0.50–0.95) ceramics are prepared by a conventional solid-state ceramic route. The microstructure and microwave dielectric properties are investigated as a function of the x-value and sintering temperature. The single phase solid solutions were obtained throughout the studied compositional range. The variation of bulk density and dielectric properties are related with the x-value. Increasing sintering temperature can effectively promote the densification and dielectric properties of xSm(Mg_0.5Ti_0.5)O₃–(1 ? x)Ca_0.8Sr_0.2TiO₃ ceramic system. With the content of Sm(Mg_0.5Ti_0.5)O₃ increasing, the temperature coefficient of resonant frequency τ _f value decreased, and a near-zero τ _f could be obtained for the samples with x = 0.80. The optimal microwave dielectric properties with a dielectric constant ε _r of 30.1, Q × f of 115,000 GHz (at 8.0 GHz), and τ _f of 8.9 ppm/°C were obtained for 0.80Sm(Mg_0.5Ti_0.5)O₃–0.20Ca_0.8Sr_0.2TiO₃ sintered at 1,550 °C for 3 h, which showed high density and well-developed grain growth.     

(Bi0.5Na0.5)1-x(BaaSrb)x TiO3无铅压电陶瓷体系的设计、制备与性能

综合考虑(Bi0.5Na0.5) TiO3(BNT)基无铅压电陶瓷的A-位、B-位原子的原子量差、离子半径差和电负性差,提出了一种BNT基无铅压电陶瓷的设计方法.依据BNT基无铅压电陶瓷所报道的相关数据,定义了ABO3型压电陶瓷的综合因子F(w)为 F(w)= M+R+100X,式中,M为A-位和B-位离子的质量差,R为A-位和B-位离子的离子半径差,X为A-位和B-位离子的电负性差.研究发现,F(w)与BNT基无铅压电陶瓷的压电耦合系数k33和kp, 以及压电常数d33有非常紧密的关系.根据该方法设计了(Bi0.5Na0.5)1-x(BaaSrb)xTiO3无铅压电陶瓷新体系,并申报了国家发明专利.研究结果表明,该体系压电陶瓷具有很好的工艺特性和压电响应,高的压电常数,其机电耦合系数kp为0.311,压电常数d33高达146pC/N,居里温度Tc为310℃,是一种很有实际应用前景的新型压电陶瓷材料体系.     

Microstructure and electrical properties of (1 − x)K0.5Na0.5NbO3–x(Ba0.85Ca0.15)(Zr0.1Ti0.9)O3 lead-free piezoelectric ceramics

The (1 ? x)K_0.5Na_0.5NbO₃ ? x(Ba_0.85Ca_0.15)(Zr_0.1Ti_0.9)O₃ (KNN–BCTZ) lead-free ceramics were fabricated by conventional solid-state sintering technique. The microstructure and electrical properties of the ceramics were investigated. The X-ray diffraction analysis revealed that the ceramics formed a single phase perovskite solid solutions with the symmetry of orthorhombic at x < 0.03. The crystal phase of the ceramics changed from orthorhombic phase to pseudocubic phase when x > 0.04. The coexistence of orthorhombic and pseudocubic (tetragonal) phases was observed near room temperature when 0.03 ≤ x ≤ 0.04. The grains grew up obviously when 2 mol% BCTZ was added, but the grain size was found to reduce gradually with further increasing BCTZ content. The T _C and T _O-T decreased with the increasing BCTZ content. The ferroelectric and piezoelectric properties were abruptly degraded as x ≥ 0.05. Optimum properties (d ₃₃ = 136 pC/N, k _p = 27 %, k _t = 26.5 %, Q _m = 25, P _r = 14.67 μC/cm², E _c = 11.23 kV/cm, T _C = 347 °C, $\varepsilon_{33}^{\text{T}} /\varepsilon_{0} = 8 6 1. 5$ ε 33 T / ε 0 = 8 6 1.5 , tan δ = 0.04) were obtained for the ceramica with x = 0.03.     

Microwave dielectric properties of (1 − y)Nd(1−2x/3)Bax(Mg0.5Sn0.5)O3–yCa0.8Sr0.2TiO3 ceramic

The (1 ? y)Nd_(1?2x/3)Ba_x(Mg_0.5Sn_0.5)O₃–yCa_0.8Sr_0.2TiO₃ ceramics were prepared by the conventional solid-state method. The X-ray diffraction patterns of the Nd_(1?2x/3)Ba_x(Mg_0.5Sn_0.5)O₃ ceramics revealed that Nd_(1?2x/3)Ba_x(Mg_0.5Sn_0.5)O₃ is the main crystalline phase, which is accompanied by a little Nd₂Sn₂O₇ as the second phase. An apparent density of 6.89 g/cm³, a dielectric constant (ε _r ) of 19.1, a quality factor (Q × f) of 212,000 GHz, and a temperature coefficient of resonant frequency (τ _f ) of ?68 ppm/°C were obtained when the Nd_2.94/3Ba_0.03(Mg_0.5Sn_0.5)O₃ ceramics were sintered at 1,550 °C for 4 h. The temperature coefficient of resonant frequency (τ _f ) increased from ?68 to +55 ppm/°C as y increased from 0 to 0.7 when the (1 ? y)Nd_2.94/3Ba_0.03(Mg_0.5Sn_0.5)O₃–yCa_0.8Sr_0.2TiO₃ ceramics were sintered at 1,600 °C for 4 h. 0.4Nd_2.94/3Ba_0.03(Mg_0.5Sn_0.5)O₃–0.6 Ca_0.8Sr_0.2TiO₃ ceramic that was sintered at 1,600 °C for 4 h had a τ _f of ?7 ppm/°C.     

Zr4+B位置换对(Pb0.5Ca0.5)(Fe(0.5)Nb0.5)O3

研究了Zr4+离子B位置换改性对(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3陶瓷微波介电性能.实验结果表明,(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3(PCFNZ)陶瓷样品呈现单一斜方钙钛矿相结构.随Zr(4+)离子的置换量增加,PCFNZ陶瓷体系的Qr值和晶粒尺寸逐渐减小;介电常数εr随着置换量增加...