喷动流化床最大喷动压降的多因素影响与关联

基于截面200 mm×20 mm,高1600 mm,锥角60°的矩形喷动流化床,以二组分混合颗粒、单一组分球形颗粒及非球形颗粒为物料进行最大喷动压降的实验研究.结果表明,最大喷动压降随静止床高、颗粒密度、颗粒球形度及二组分混合颗粒体系中沉积组分分率增加而增大,随流化气速增大而减小;增大颗粒粒径或喷口宽度,呈现先减小后增...     

细颗粒喷动床的流体力学特性

在直径186 mm的喷动床中考察了细颗粒(d_p＝0.241～0.874 mm)体系的流体力学性质及夹带和磨损特性.采用不同的喷嘴直径(D_i＝6～14 mm)和锥底顶角(θ＝45°～80°)对其操作状态进行了研究,发现当D_i/d_p<19～21时可以形成稳定喷动.随着气体速度的增加,床层依次出现固定床、稳定喷动、不良喷动和腾涌等4个流动区域.实验测量的最小喷动速度与Mathur-Gishler关联式的误差在±15%之内.采用γ射线扫描仪测量了固体密度分布,结果表明喷动区的固体密度随高度的增加而增加,环流区的密度比松堆密度大3%～10%.颗粒的磨损和夹带随着气速的增大而增大,在稳定有序的喷动状态下变得最小.     

喷动流化床流动形态变化的试验研究国家

在一个可视化的半圆柱喷动流化床试验台上研究了喷动流化床的流形变化规律。研究表明：随着喷动气量和流化气量的改变,床内会呈现不同的流动形态：固定床、带射流的流化床、喷动床、充气喷动床和喷动流化床。同时研究了量小喷动速度和最小喷动流化速度随喷动管内径、颗粒粒径、静止床高的变化规律,归纳了预测量小喷动速度和最小喷动流化速度的试验关联式,绘制了喷动流化床的流形划分相图。     

导向管充气喷动床流体力学性能

在内径92mm的有机玻璃床内,对导向管充气喷动床的操作相图、床层压降、最小喷动速度及最大弃气速度进行了研究.实验采用4种颗粒为实验物料并采用空气为 喷动和弃气气体,通过对实验数据的回归得到用于计算或判别导向管弃气喷动床最小喷动速度和最大充气速度的计算式,以便为其设计和操作提供依据.     

喷动流化床的最小喷动流化速度和床层压降

在一喷动流化床（直径 ５０ ｍｍ）实验台上采用 ０．６３～１．６０ ｍｍ的神府原煤颗粒,在连续进料的情况下进行了最小喷动流化速度以及固定流化气、改变喷动气和固定喷动气、改变流化气的床层压降变化的实验研究．结果表明,最小喷动流化速度可以参考鼓泡流化床的临界流化速度的计算方法;床层压降变化证实,喷动流化床具有良好的调节能力．     

加压喷动床中细颗粒喷动特性

在内径分别为 186mm和 80mm的加压喷动床中 ,以空气为喷动介质 ,在 10 1～ 70 0kPa的压力范围内考察了几种不同粒度的细颗粒在加压下的喷动特性 .研究结果表明在不同的Re_t 内压力对最小喷动速度的影响不同 .实验还发现 ,随着压力的升高 ,喷动区直径增大 ,稳定操作区域增大 ,加压可明显改善喷动床的操作稳定性     

导向管喷动流化床的喷动气旁路分率

在内径为182 mm的喷动流化床中安装内径80 mm的导向管,以平均粒径为2.2 mm的尿素颗粒为物料,对喷动气旁路特性进行了实验研究,分别考察了夹带区高度、导向管长度、喷嘴内径、床层高度、喷动气速和流化气速对喷动气旁路分率的影响,结果表明随着喷动气速的增大,喷动气体旁路分率先增后减。导向管安装高度越高,气体旁路分率越大。床层高度增大喷动气体旁路分率略有降低。而喷嘴直径小于50 mm时气体旁路分率随喷嘴直径增大而提高,在大于50 mm时气体旁路分率随喷嘴直径增大维持不变。当气速较小时,导向管高度增大会引起气体旁路分率增大,引入少量流化气能有效地抑制喷动气旁路。     

双喷嘴矩形喷动床流动性能实验研究

在120 mm×240 mm的双喷嘴矩形不锈钢床内,对新型双喷嘴矩形导流管喷动床的最小喷动速度和喷动高度进行了研究,考察了喷动气速、粒径、静床层高度、导流管直径、导流管安装位置对最小喷动速度和喷动高度的影响。结果表明:最小喷动速度随颗粒直径、导流管直径、导喷距的增大而增大,随静床层高度的增大而减小;喷动高度随喷动气速的增大而增大,随导流管直径的增大而减小,受静床层高度和导喷距的影响不大,并得出了最小喷动速度的关联式。     

狭缝式矩型喷动床中多粒度颗粒体系的最小喷动速度

在150 mm×50 mm×1100 mm的矩形喷动床中,采用宽度为2, 4, 6 mm 的3种狭缝式气体分布板,研究了单一粒度组成和多粒度组成玻璃珠的最小喷动速度. 实验证明,矩形喷动床的最小喷动速度与物料的粒度和组成有关. 给出了最小喷动速度与颗粒粒径和粒度组成的关联式,作出了多粒度组成颗粒体系最小喷动速度的相图.     

狭缝式矩形喷动床中多粒度颗粒体系的最大喷动压降

在 15 0 mm× 5 0 mm× 110 0 mm的矩形喷动床中 ,研究了单一粒径体系和二组分及三组分混合粒径颗粒体系的最大喷动压降受颗粒粒径及粒度组成、静止床高和气体入口狭缝宽度的影响情况。实验采用宽度为2、4、6 mm三种宽度的狭缝式气体分布板 ,实验物料为单一粒径分别为 1、1.5、2 mm的玻璃珠。实验表明矩形喷动床的最大喷动压降与上述三种影响因素都有关系。本文还给出了最大喷动压降随这三种因素变化的实验关联式     

气固流化床内射流穿透深度的CFD模拟及其实验验证

在经典的Gidaspow无黏性双流体模型中考虑离散颗粒对流体和固体动量守恒方程的影响后,建立了一个具有模拟大规模流化床内气固两相流体动力学特性潜在优势的简化数学模型。在CFX4.4商业化软件平台上通过增加用户自定义子程序考察了二维气固流化床(高2.00 m、宽0.30 m)内射流气速、喷嘴尺寸、环隙气速和静床高度对射流穿透深度的影响,并以树脂颗粒(粒径670 μm、密度1474 kg·m^-3)为研究对象在厚度为0.025 m的矩形床内进行了对比实验。结果表明,选取空隙率为0.8的等高线作为射流边界比较合适;射流穿透深度随射流气速或射流喷口尺寸的增加而增大;射流周围环隙气速由0变到最小流化速度时,射流穿透深度随环隙气速增加而增大,在最小流化速度时达到最大值,然后随环隙气速增加单调减小,当环隙气速大于2.5倍最小流化速度时,射流穿透深度减小程度变缓;在相同射流气速下射流穿透深度随着静床高度的增加而减小,静床高度对射流穿透深度的影响随着射流气速增加呈现扩大的趋势。     

Separation and residence times of larger particles in a spout-fluid bed

Optimum conditions for the separation of added large particles from a spout-fluid bed of Geldart Type B powder have been determined. A shallow bed, 100 mm in diameter, with porous conical distributor was used. Mean and distributions of residence time of the large particles depend on the two gas flow rates, especially that to the distributor, and on spout inlet diameter and large particle size. Bed regimes studied were mainly spouting with aeration and spout-fluidization. In the latter regime an optimum range of fluidizing gas flow rates that minimised mean and spread of residence times was identified. RTD data were correlated by a model incorporating a minimum time supplemented by a distribution for an ideally mixed system.     

Jet penetration depth in a two-dimensional spout-fluid bed

The jet penetration depth was proposed to be an important parameter to describe the jet action during the chemical process of spout-fluid bed coal gasification. A two-dimensional cold model of a spout-fluid bed coal gasifier with its cross section of and height of 2000 mm was established to investigate the jet penetration depth. Four types of Geldart group D particles were used as bed materials. A multi-channel pressure sampling system and a high-resolution digital CCD camera were employed for experimental investigations. The effects of spouting gas velocity, spout nozzle diameter, static bed height, particle property and fluidizing gas flow rate on the jet penetration depth have been systematically studied by pressure signal analysis and image processing. Experimental results indicate that the jet penetration depth increases with increasing spouting gas velocity and spout nozzle diameter, while it decreases with increasing particle density, particle diameter, static bed height and fluidizing gas flow rate. Additional, a new correlation considered all of the above effects especially static bed height and fluidizing gas flow rate, was developed for predicting the jet penetration depth in spout-fluid beds. The correlation was compared with published experimental data or correlations, which was in well agreement with the present experimental results and some other references.     

Pressure Fluctuations in Jet Spouted Beds

Jet spouted beds that consisted of a transparent Plexiglas cylindrical column of 1 m high and a conical base with cone angles of 30°, 36°, and 40° were used in this study. The particles used were spherical glass beads with an average diameter of 1.7, 2.1 and 3 mm, respectively, and particle size of 2.2 – 3.1 mm, non‐spherical rice particles. The effect of size and shape of particles, and static bed height on the minimum jet spouting velocity, and standard deviation of pressure fluctuations, was investigated. The results show that the minimum jet spouting velocity and pressure drop increased as the bed height and particle size increased. The minimum jet spouting velocity could be determined from the plot of standard deviation of pressure fluctuations vs. superficial gas velocity. The results obtained were in close agreement with the results of other methods in the literature.     

Pressure and flow characteristics of a gas phase spout-fluid bed and the minimum spout-fluid condition

Spoutfluidization is a new technique for solid-fluid contact which aims at incorporating the advantages of spouted bed and fluidized bed technique. The characteristics of physical state of the bed with the variation of the variables which include flow of fluid, particle diameter, orifice diameter, bed height, are studied in this investigation. Experimental study of minimum spoutfluidizing velocity using glass beads with mean particle diameters from 0.254 to 0.600 mm has been carried out in a 90 mm glass column with three spouting inlet orifice sizes at different bed heights. Phase diagrams indicate that the minimum spout-fluid flow rate in a gas-solid system may be a point property for a given bed. A correlation is presented in which the standard deviation of experimental from calculated minimum spoutfluidizing velocity is within 5%.     

基于颗粒流运动论的喷动流化床气固流动行为三维模拟

1 INTRODUCTION Spout-fluid beds have been of increasing interest in the petrochemical, chemical and metallurgic indus-tries since spout-fluid beds can reduce some of the limitations of both spouting and fluidization by su-perimposing the two type of systems[1―4]. In recent years, spout-fluid beds have become an alternative for gas/solid contactors in coal gasification. Spout-fluid bed coal gasifiers have been adopted for APFBC-CC (advanced pressurized fluidized bed combus-tion-combined…     

Pressure drop and flowrate characteristics of a liquid phase spout-fluid bed at the minimum spout-fluid flowrate

Data on the minimum spout-fluid flowrates and the pressure drop in the annulus at that flowrate are presented as a function of bed height and nozzle diameter for a bed spout-fluidized with water. The column was 62.6 mm. in diameter and contained 3.09 mm. glass particles. The particle Reynolds number at the minimum fluidizing velocity was 91.6. A plot of the annular vs. the nozzle flowrate shows that the minimum spout-fluid flowrates fall on a straight line between the minimum fluidizing and minimum spouting flowrates. The annular pressure drop is explained using an extension of the theory of Mamuro and Hattori.     

一个基于双流体理论预测三维流化床内流动特性的数学模型(Ⅰ)气固体系散式或鼓泡流态化特性

将考虑拟平衡状态下颗粒与流体相互作用的附加力添加到基于双流体理论动量方程的数学模型中,用于Geldart A类物料散式流态化和B类物料鼓泡/床层塌落特性的三维数值模拟。该模型主要特点是将表征颗粒离散属性的特征长度视为颗粒直径的同一数量级且只需曳力系数一个关联式来封闭控制方程。在商业软件CFX4.4平台上,通过增加用户自定义子程序模拟了长0.2 m、宽0.2 m和高0.5 m流化床内瞬态流动特性。为了检验数学模型的实用性和数值模拟的可靠性,首先考察了两种A类物料在表观气速为u_mf和1.5u_mf下的散式流态化特性,结果展示出床层均匀膨胀的固有属性。随后,考察了扰动对A类物料在网格尺度上的局部空隙率和固体速度分布以及在设备尺度上床层压降的影响,探索了B类物料在网格尺度上鼓泡和床层塌落以及在设备尺度上鼓泡过程中床层压降和塌落过程中平均床层高度和相界面标准偏差的动态特性。上述模拟结果与经典的Geldart理论、前人的实验或模拟结果相吻合,说明该模型可以用来预报三维气固流化床内A类物料散式流态化和B类物料鼓泡及塌落的时空特性。     

超细粉在导向管喷动床中的固体循环速率

Ultra-fine powders are difficult to be fluidized due to the strong particle to particle cohesiveness.However, the authors‘ experiments showed that the ultra-fine powder CaCO3 could be stably fluidized in a spouted bed with a draft tube. The effects of geometric and operating parameters on solid circulation rate of ultra-fine powder CaCO3 were investigated in a 120 mm diameter transparent semicircular spouted bed with a draft tube. Three draft tubes with different sizes were used in this study. It was found that the solids circulation rate was mainly dependent on the drawing rate of the gas jet from the nozzle, then on the gas transport capacity in the draft tube. With increasing gas feed rate, distance between the nozzle and the draft tube inlet and draft tube diameter, the solids circulation rate could be increased. Based on the jet theory, a quantitative correlation was proposed for predicting the solid circulation rate of ultra-fine powders in a spouted bed with a draft tube by taking into account the gas transport capacity in the draft tube.