椭圆环形截面钢柱的设计

对椭圆环形截面钢柱进行数值模拟和设计。建立准确的有限元模型,模拟两端固接的椭圆环形钢柱。对拉伸试验得出的材料非线性及初始局部(整体)几何缺陷都进行了考虑,通过收敛性研究,以获得最佳的单元网格尺寸。采用此数值模型,对100根柱试件进行参数化研究。对材料屈服、局部屈曲、弯曲屈曲及局部屈曲与弯曲屈曲同时发生的破坏模型进行了分析。将柱的承载力试验值和数值分析结果与基于北美规范、澳大利亚规范、新西兰规范和欧洲规范的计算值进行对比。另外,还采用了不适用于椭圆环形截面钢杆的直接强度法进行分析。对这些设计方法均进行了可靠度分析。     

Design of cold-formed steel unequal angle compression members

Cold-formed steel unequal angles are non-symmetric sections. The design procedure of non-symmetric sections subjected to axial compression load could be quite difficult. The unequal angle columns may fail by different buckling modes, such as local, flexural and flexural–torsional buckling as well as interaction of these buckling modes. The purpose of this study is to investigate the behaviour and design of cold-formed steel unequal angle columns. A nonlinear finite element analysis was conducted to investigate the strength and behaviour of unequal angle columns. The measured initial local and overall geometric imperfections as well as the material properties of the angle specimens were included in the finite element model. The finite element analysis was performed on fixed-ended columns for different lengths ranged from stub to long columns. It is demonstrated that the finite element model closely predicted the experimental ultimate loads and the behaviour of cold-formed steel unequal angle columns. Hence, the model was used for an extensive parametric study of cross-section geometries. The column strengths obtained from the parametric study were compared with the design strengths calculated using the North American Specification for cold-formed steel structural members. It is shown that the current design rules are generally unconservative for short and intermediate column lengths for the unequal angles. Therefore, design rules of cold-formed steel unequal angle columns are proposed.     

Structural performance of cold-formed high strength stainless steel columns

This paper describes an accurate finite element model for the structural performance of cold-formed high strength stainless steel columns. The finite element analysis was conducted on duplex stainless steel columns having square and rectangular hollow sections. The columns were compressed between fixed ends at different column lengths. The effects of initial local and overall geometric imperfections have been taken into consideration in the finite element model. The material nonlinearity of the flat and corner portions of the high strength stainless steel sections were carefully incorporated in the model. The column strengths and failure modes as well as the load-shortening curves of the columns were obtained using the finite element model. Furthermore, the effect of residual stresses in the columns was studied. The nonlinear finite element model was verified against experimental results. An extensive parametric study was carried out using the verified finite element model to study the effects of cross-section geometries on the strength and behaviour of cold-formed high strength stainless steel columns. The column strengths predicted from the parametric study were compared with the design strengths calculated using the American Specification, Australian/New Zealand Standard and European Code for cold-formed stainless steel structures. The results of the parametric study showed that the design rules specified in the American, Australian/New Zealand and European specifications are generally conservative for cold-formed high strength stainless steel square and rectangular hollow section columns, but unconservative for some of the short columns.     

Buckling analysis of high strength stainless steel stiffened and unstiffened slender hollow section columns

This paper investigates the buckling behaviour of cold-formed high strength stainless steel stiffened and unstiffened slender square and rectangular hollow section columns. The high strength duplex material is austenitic-ferritic stainless steel approximately equivalent to EN 1.4462 and UNS S31803. The columns were compressed between fixed ends at different column lengths. A nonlinear finite element model has been developed to investigate the behaviour of stiffened slender square and rectangular hollow section columns. The column strengths, load-shortening curves as well as failure modes were predicted for the stiffened and unstiffened slender hollow section columns. An extensive parametric study was conducted to study the effects of cross-section geometries on the strength and behaviour of the stiffened and unstiffened columns. The investigation has shown that the high strength stainless steel stiffened slender hollow section columns offer a considerable increase in the column strength over that of the unstiffened slender hollow section columns. The column strengths predicted from the parametric study were compared with the design strengths calculated using the American Specification, Australian/New Zealand Standard and European Code for cold-formed stainless steel structures. It is shown that the design strengths obtained using the three specifications are generally conservative for the cold-formed stainless steel unstiffened slender square and rectangular hollow section columns, but slightly unconservative for the stiffened slender square and rectangular hollow section columns.     

Design of cold-formed steel channels with stiffened webs subjected to bending

The objectives of this study are to investigate the structural behaviour and evaluate the appropriateness of the current direct strength method on the design of cold-formed steel stiffened cross-sections subjected to bending. The stiffeners were employed to the web of plain channel and lipped channel sections to improve the flexural strength of cold-formed steel sections that are prone to local buckling and distortional buckling. An experimental investigation of simply supported beams with different stiffened channel sections has been conducted. The moment capacities and observed failure modes at ultimate loads were reported. A nonlinear finite element model was developed and verified against the test results in terms of strengths, failure modes and moment–curvature curves. The calibrated model was then adopted for an extensive parametric study to investigate the moment capacities and buckling modes of cold-formed steel beams with various geometries of stiffened sections. The strengths and failure modes of specimens obtained from experimental and numerical results were compared with design strengths predicted using the direct strength method specified in the North American Specification for cold-formed steel structures. The comparison shows that the design strengths predicted by the current direct strength method (DSM) are conservative for both local buckling and distortional buckling in this study. Hence, the DSM is modified to cover the new stiffened channel sections investigated in this study. A reliability analysis was also performed to assess the current and modified DSM.     

Aluminum alloy tubular columns—Part II: Parametric study and design using direct strength method

A parametric study of aluminum alloy columns of square and rectangular hollow sections was performed using finite element analysis (FEA). The columns were compressed between fixed ends. The parametric study included 120 columns with and without transverse welds at the ends of the columns. An accurate and reliable finite element model was used for the parametric study. Design approaches for aluminum alloy tubular columns with and without transverse welds were proposed. Column strengths predicted by the FEA were compared with the design strengths calculated using the current American, Australian/New Zealand and European specifications for aluminum structures. In addition, the direct strength method (DSM), which was developed for cold-formed carbon steel members, was used in this study for aluminum alloy columns. The design strengths calculated using the DSM were compared with the numerical results. Furthermore, design rules modified from the DSM were proposed. It is shown that the proposed design rules accurately predicted the ultimate strengths of aluminum welded and non-welded columns. The reliability of the current and proposed design rules was evaluated using reliability analysis.     

Structural performance of cold-formed lean duplex stainless steel columns

The structural performance of cold-formed lean duplex stainless steel columns was investigated. A wide range of finite element analysis on square and rectangular hollow sections and other available data, with a total number of 259 specimens, were considered. An accurate finite element model has been created to simulate the pin-ended cold-formed lean duplex stainless steel columns. Extensive parametric study was carried out using the validated finite element model. The column strengths predicted from the parametric study together with the available data are compared with the design strengths calculated from various existing design rules for cold-formed stainless steel structures. It is shown that the existing design rules, except for the ASCE Specification as well as the stub column and full area approach, are conservative. Modifications are proposed for the AS/NZS Standard, EC3 Code, and direct strength method. Reliability analysis was performed to assess the existing and modified design rules. It is also shown that the modified design rules are able to provide a more accurate and reliable predictions for lean duplex stainless steel columns. In this study, it is suggested that the modified design rules in the AS/NZS Standard and the modified direct strength method to be used in designing cold-formed lean duplex stainless steel columns.     

Numerical investigation of channel columns with complex stiffeners—part II: parametric study and design

A parametric study of cold-formed steel channel columns with complex stiffeners is performed using finite element analysis. An accurate and reliable finite element model is used for the parametric study in which different sizes of complex stiffeners are investigated. Column strengths predicted by the finite element analysis are compared with the unfactored design column strengths calculated using the American Specification and the Australian/New Zealand Standard for cold-formed steel structures. It is shown that the design strengths obtained from the specification and standard are generally conservative for fixed-ended cold-formed steel channel columns with complex stiffeners for the more slender sections having a plate thickness of 1 mm with the flat flange width to thickness ratio of 57, but unconservative for sections having a plate thickness of 2 mm with the flat flange width to thickness ratio of 27.     

Experimental and numerical investigation of cold-formed lean duplex stainless steel flexural members

Experimental and numerical investigation of cold-formed lean duplex stainless steel flexural members is presented in this paper. The test specimens were cold-rolled from flat plates of lean duplex stainless steel with the nominal 0.2% proof stress of 450 MPa. Specimens of square and rectangular hollow sections subjected to both major and minor axes bending were tested. A finite element model has been created and verified against the test results using the material properties obtained from coupon tests. It is shown that the model can accurately predict the behaviour of lean duplex stainless steel flexural members. An extensive parametric study was carried out using the verified finite element model. The test and numerical results as well as the available data on lean duplex beams are compared with design strengths predicted by various existing design rules, such as the American Specification, Australian/New Zealand Standard, European Code and direct strength method for cold-formed stainless steel. Reliability analysis was performed to evaluate the reliability of the design rules. It is shown that these current design rules provide conservative predictions to the design strengths of lean duplex stainless steel flexural members. In this study, modified design rules on the American Specification, Australian/New Zealand Standard, European Code and direct strength method are proposed, which are shown to improve the accuracy of these design rules in a reliable manner.     

Experimental investigation of built-up cold-formed steel section battened columns

This paper presents an experimental investigation on behaviour and design of built-up cold-formed steel section battened columns. The built-up columns were pin-ended and consisted of two cold-formed steel channels placed back-to-back at varied spacing of intersection. The two channels were connected using batten plates, with varying longitudinal spacing. The cold-formed steel channel sections were manufactured by brake-pressing flat strips having a plate thickness of 2 mm. The built-up cold-formed steel section battened columns had different slenderness and geometries but had the same nominal length of 2200 mm. The column strengths, load–axial shortening, load–lateral displacement and load–axial strain relationships were measured in the tests. In addition, the failure modes and deformed shapes at failure were observed in the tests and reported in this paper. Overall, the built-up column tests provided valuable experimental data regarding the column behaviour that compensated the lack of information on this form of construction as well as used to develop nonlinear 3-D finite element models. The column strengths measured experimentally were compared against design strengths calculated using the North American Specification, Australian/New Zealand Standard and European Code for cold-formed steel columns. Generally, it is shown that the specifications were unconservative for the built-up cold-formed steel section battened columns failing mainly by local buckling, while the specifications were conservative for the built-up columns failing mainly by elastic flexural buckling.     

国际期刊导读

采用有限元方法,对冷弯不锈钢方管、矩形管支撑和弦杆中的T型、X型及预应力X型节点进行数值分析。考虑几何非线性和材料非线性,获得节点承载力、破坏模式及荷载-位移曲线。利用试验结果,对T型、X型矩形管、方管节点的非线性有限元模型进行修正,直到有限元结果和试验结果足够吻合。采用修正后的有限元模型对172个T型、X型节点进行参数分析,研究冷弯不锈钢管节点强度和性能的影响。将数值分析和试验中获得的节点承载力与按规范计算的设计承载力进行对比。对不锈钢管结构,采用澳大利亚规范、新西兰规范计算;对碳素钢管结构,采用国际管结构发展与研究委员会设计规范和欧洲设计规范计算。通过可靠性分析,分别评价本文提出的设计方法和现有规范的可靠度。结果表明：采用本文方法计算的设计承载力更准确、更可靠。     

New design rules for the shear strength of LiteSteel beams

The LiteSteel Beam (LSB) is a new cold-formed hollow flange channel section produced using dual electric resistance welding and automated continuous roll-forming technologies. The innovative LSB sections have many beneficial characteristics and are commonly used as flexural members in building construction. However, limited research has been undertaken on the shear behaviour of LSBs. Therefore a detailed investigation, including both numerical and experimental studies, was undertaken to investigate the shear behaviour of LSBs. Finite element models of LSBs in shear were developed to simulate the nonlinear ultimate strength behaviour of LSBs, including their elastic buckling characteristics, and were validated by comparing their results with experimental test results. Validated finite element models were then used in a detailed parametric study into the shear behaviour of LSBs. The parametric study results showed that the current design rules in cold-formed steel structures design codes are very conservative for the shear design of LSBs. Significant improvements to web shear buckling occurred due to the presence of torsionally rigid rectangular hollow flanges, while considerable post-buckling strength was also observed. This paper therefore proposes improved shear strength design rules for LSBs within the current cold-formed steel code guidelines. It presents the details of the parametric study and the new shear strength equations. The new equations were also developed based on the direct strength method. The proposed shear strength equations have the potential to be used with other conventional cold-formed steel sections such as lipped channel sections.     

Design of cold-formed stainless steel tubular T- and X-joints

This paper describes the numerical investigation of cold-formed stainless steel tubular T-joints, X-joints and X-joints with chord preload using finite element analysis. The stainless steel joints were fabricated from square hollow section (SHS) and rectangular hollow section (RHS) brace and chord members. The geometric and material nonlinearities of stainless steel tubular joints were carefully incorporated in the finite element models. The joint strengths, failure modes as well as load-deformation curves of stainless steel tubular joints were obtained from the numerical analysis. The nonlinear finite element models were calibrated against experimental results of cold-formed stainless steel SHS and RHS tubular T- and X-joints. Good agreement between the experimental and finite element analysis results was achieved. Therefore, an extensive parametric study of 172 T- and X-joints was then carried out using the verified finite element models to evaluate the effects of the strength and behaviour of cold-formed stainless steel tubular joints. The joint strengths obtained from the parametric study and tests were compared with the current design strengths calculated using the Australian/New Zealand Standard for stainless steel structures, CIDECT and Eurocode design rules for carbon steel tubular structures. Furthermore, design formulae of cold-formed stainless steel tubular T- and X-joints are proposed. A reliability analysis was performed to assess the reliability of the current and proposed design rules. It is shown that the design strengths calculated using the proposed equations are generally more accurate and reliable than those calculated using the current design rules.     

不锈钢轴心受压柱弯曲屈曲承载力分析

为给我国《不锈钢结构技术规范》中轴心受压柱弯曲屈曲稳定部分的编制提供依据,对国外已有的同类构件的设计方法和试验研究数据进行搜集和对比。结果表明：目前的欧洲不锈钢结构设计规范和美国冷成型不锈钢结构设计规范中计算该类构件的公式均存在一定不足。依据搜集到的199个方管、矩形管、圆管、椭圆管、焊接H形钢和冷弯C型钢截面柱的试验数据,根据冷弯效应及残余应力对轴心受压构件稳定性能的影响,将构件依据截面形式分为A、B、C三类,其中方管、矩形管和冷弯C型钢为A类,圆管和椭圆管为B类,焊接H形钢为C类,三类轴心受压稳定曲线均采用Perry公式形式表达。与试验数据对比表明：采用三类曲线能较好地估算构件的稳定承载力且离散性较小。对提出的计算式进行可靠度分析,结果表明其可靠度指标β满足我国GB 50068-2001《建筑结构可靠度设计统一标准》的要求。     

Experimental and numerical investigations of cold-formed stainless steel tubular sections subjected to concentrated bearing load

Experimental and numerical investigations of cold-formed stainless steel square and rectangular hollow sections subjected to concentrated bearing load are presented in this paper. A total of 124 data are presented that include 64 test results and 60 numerical results. The tests were performed on austenitic stainless steel type 304, high strength austenitic and duplex material. The measured web slenderness value of the tubular sections ranged from comparatively stocky webs of 6.2 to relatively more slender webs of 61.4. The tests were carried out under end and interior loading conditions. A non-linear finite element model is developed and verified against experimental results. Geometric and material non-linearities were included in the finite element model. The material nonlinearity of the flat and corner portions of the specimen sections were carefully incorporated in the model. It was shown that the finite element model closely predicted the web crippling strengths and failure modes of the tested specimens. Hence, the model was used for an extensive parametric study of cross-section geometries, and the web slenderness value ranged from 52.0 to 206.7. The test results and the web crippling strengths predicted from the finite element analysis were compared with the design strengths obtained using the American, Australian/New Zealand and European specifications for stainless steel structures. A unified web crippling equation with new coefficients for cold-formed stainless steel square and rectangular hollow sections subjected to concentrated bearing load is proposed. It is demonstrated that the proposed web crippling equation is safe and reliable using reliability analysis.     

Nonlinear analysis of concrete-filled steel SHS and RHS columns

This paper presents an accurate nonlinear finite element model for the behaviour and design of axially loaded concrete-filled square hollow section (SHS) and rectangular hollow section (RHS) steel tube columns. The nonlinear material models for confined concrete and steel tubes were carefully modeled in the finite element analysis. The column strengths and load-axial shortening curves were evaluated. The results obtained from the finite element analysis were verified against experimental results. An extensive parametric study was conducted to investigate the effects of different concrete strengths and cross-section geometries on the strength and behaviour of concrete-filled SHS and RHS steel tube columns. The study was conducted over a wide range of concrete cube strengths ranged from 30 to 110 MPa. The overall depth of the steel tube-to-plate thickness ratio ranged from 10 to 40 covering compact SHS and RHS steel tube sections. The column strengths predicted from the finite element analysis were compared with the design strengths calculated using the American, Australian and European specifications. Based on the results obtained from the parametric study, it is found that the design strengths calculated using the American Specifications and Australian Standards are conservative, while the design strengths calculated using the European Code are accurate, except for the concrete-filled RHS compact steel tube columns having the overall depth of the steel tube-to-plate thickness ratio of 40.     

Structural response of stainless steel oval hollow section compression members

Cold-formed stainless steel oval hollow sections (OHS) offer the combined aesthetic appeal of circular hollow sections and stainless steel, together with the structural efficiency associated with cross-sections of differing geometric properties about their two principal axes. To date, no structural design guidance exists for these cross-sections, principally due to their relatively recent introduction and a lack of fundamental structural test data. This paper examines the structural response of stainless steel OHS compression members and presents design recommendations. A series of laboratory tests was carried out to generate fundamental structural performance data. Tensile coupon tests were initially performed to establish the basic material stress–strain characteristics of the sections. These were followed by stub column tests to determine the average compressive response of the cross-sections and flexural buckling tests to obtain ultimate load carrying capacity data for use in the determination of a suitable buckling curve for stainless steel OHS. Measurements of the geometric properties of the test specimens including initial imperfections were carried out. The full load–displacement responses of the specimens were recorded and have been presented herein. A finite element (FE) modelling programme was performed in parallel with the experimental study. Once the FE models had been validated against the test results, parametric studies were carried out to further investigate the influence of individual key parameters, including the aspect ratio and local slenderness of the cross-sections as well as the member slenderness. Based on the obtained experimental and numerical results, a class 3 limit for stainless steel OHS in compression and a suitable buckling curve for OHS columns have been proposed.     

Local and distortional buckling of cold-formed steel beams with both edge and intermediate stiffeners in their compression flanges

The true buckling behaviour of cold-formed steel beams with both edge and intermediate stiffeners in their compression flanges has been predicted with the aid of advanced numerical modelling. A series of nonlinear finite element analyses has been carried out to investigate the flexural behaviour of cold-formed Z sections with both edge and intermediate stiffeners in their flanges, when the failure is controlled by local and/or distortional buckling. The effect of the size and position of intermediate stiffeners as well as the effect of the edge stiffener/intermediate stiffener interaction on the buckling behaviour and ultimate strength of these sections has been studied. The knowledge gained from FE analyses was used to check the accuracy of the Eurocode design rules in predicting the ultimate strengths for these sections.     

受压翼缘外带卷边和中间加劲肋的冷弯型钢梁的局部和扭转屈曲特性

采用数值模型分析受压翼缘含卷边和中间加劲肋的冷弯型钢梁的屈曲特性。通过一系列非线性有限元分析,研究了由局部或扭转屈曲导致失稳的两侧翼缘处均含卷边和中间加劲肋的冷弯Z型钢的弯曲性能。研究了中间加劲肋的尺寸和位置以及卷边加劲肋和中间加劲肋的相互作用对型材的屈曲特性和极限强度的影响。有限元分析结果常可用来检验用欧洲设计规范在预测这类断面极限强度时的精确度。     

Design of high strength steel columns at elevated temperatures

The main objective of this paper is to study the behaviour and design of high strength steel columns at elevated temperatures using finite element analysis. In this study, equations predicting the yield strength and elastic modulus of high strength steel and mild steel at elevated temperatures are proposed. In addition, stress-strain curve model for high strength steel and mild steel materials at elevated temperatures is also proposed. The numerical analysis was performed on high strength steel columns over a range of column lengths for various temperatures. The nonlinear finite element model was verified against experimental results of columns at normal room and elevated temperatures. The effects of initial local and overall geometrical imperfections have been taken into consideration in the analysis. The material properties and stress-strain curves at elevated temperatures used in the finite element model were obtained from the proposed equations based on the material tests. Two series of box and I-section columns were studied using the finite element analysis to investigate the strength and behaviour of high strength steel columns at elevated temperatures. Both fixed-ended stub columns and pin-ended slender columns were considered. The column strengths predicted from the finite element analysis were compared with the design strengths predicted using the American, European and Australian specifications for hot-rolled steel columns at elevated temperatures by substituting the reduced material properties. In addition, the direct strength method, which was developed for the design of cold-formed steel columns at normal room temperature, was also used in this study to predict the high strength steel column strengths at elevated temperatures. The suitability of these design rules for high strength steel columns at elevated temperatures is assessed. Generally, it is shown that the American and European specifications as well as the direct strength method conservatively predicted the column strengths of high strength steel at elevated temperatures. The European Code predictions are slightly more conservative than the American Specification and the direct strength method predictions.