吸波材料辅助的液体物料微波冷冻干燥多物理场耦合模型

为了研究吸波材料辅助微波加热对传统冷冻干燥过程的强化作用,建立了多孔介质温度、浓度和电磁场耦合的多相传递模型;以烧结的碳化硅(SiC)为吸波材料、以甘露醇水溶液为待干料液进行了微波冷冻干燥实验,并测定了甘露醇固体的介电特性。模拟和实验结果均表明,吸波材料对初始非饱和多孔物料微波冷冻干燥具有显著的强化作用。初始非饱和样品微波冷冻干燥时间比传统冷冻干燥缩短了18%,比常规饱和样品传统冷冻干燥缩短了30%。模拟结果与实验数据吻合良好。这表明提出的新型干燥方法确实能够实现过程传热传质的同时强化。通过考察样品内部温度、饱和度和电场强度的实时分布,分析了微波冷冻干燥过程的传热传质和电磁波传播与耗散机理。在微波冷冻干燥过程中,初始非饱和样品累计吸收的辐射能和微波能的总和与传统冷冻干燥相当。这说明,该干燥方法只是提高了能量效率,从而大幅缩短了冷冻干燥时间。     

具有预制孔隙的维生素C水溶液微波冷冻干燥

设计和组装了一套实验室规模的多功能微波冷冻干燥装置,探究了具有初始孔隙的非饱和物料微波冷冻干燥过程。以维生素C为溶质,采用"软冰"冷冻技术制备了初始饱和与非饱和的冷冻样品。结果表明,软冰冷冻制备的样品能够避免崩塌。在35℃和20 Pa条件下,初始非饱和物料的干燥时间比饱和物料缩短了30.4%。SEM表征显示,非饱和物料具有疏松的球状孔隙结构、连通性好,有利于水蒸气的迁移。采用吸波材料碳化硅辅助的微波加热能够进一步强化冷冻干燥过程。在相同条件下,非饱和物料的微波冷冻干燥(5 W功率)时间比常规冷冻干燥(0 W功率)缩短了28.1%,比饱和物料的常规冷冻干燥缩短了50.0%。吸波材料辅助的初始非饱和物料微波冷冻干燥实现了传热传质的同时强化。     

具有预制孔隙的维生素C水溶液微波冷冻干燥

设计和组装了一套实验室规模的多功能微波冷冻干燥装置，探究了具有初始孔隙的非饱和物料微波冷冻干燥过程。以维生素C为溶质，采用“软冰”冷冻技术制备了初始饱和与非饱和的冷冻样品。结果表明，软冰冷冻制备的样品能够避免崩塌。在35℃和20 Pa条件下，初始非饱和物料的干燥时间比饱和物料缩短了30.4%。SEM表征显示，非饱和物料具有疏松的球状孔隙结构、连通性好，有利于水蒸气的迁移。采用吸波材料碳化硅辅助的微波加热能够进一步强化冷冻干燥过程。在相同条件下，非饱和物料的微波冷冻干燥(5 W功率)时间比常规冷冻干燥(0 W功率)缩短了28.1%，比饱和物料的常规冷冻干燥缩短了50.0%。吸波材料辅助的初始非饱和物料微波冷冻干燥实现了传热传质的同时强化。     

具有初始孔隙的多孔物料冷冻干燥

实验研究了具有一定孔隙的非饱和多孔物料对液体物料冷冻干燥过程的影响。以甘露醇为主要溶质的待干料液采用“液氮制冰激凌法”制备非饱和物料进行冷冻干燥,并与常规饱和的冷冻物料相比较。结果表明,非饱和冷冻物料确实能够显著地强化液体物料的冷冻干燥过程。干燥产品SEM形貌分析显示,初始非饱和冷冻物料具有连续均匀的固体骨架和孔隙,固体基质更加纤细,孔隙空间更大,可以大大减小传质阻力。考察物料内部各点的温度变化发现,初始非饱和物料内部冰晶确实发生整体升华,但仍然存在主要升华区域;非饱和多孔物料的冷冻干燥过程主要是传热控制,而常规饱和物料冷冻干燥主要是传质控制。操作压力对过程的影响可以忽略。采用辐射/导热组合加热方式可改善初始非饱和多孔物料冷冻干燥过程的传热,进一步缩短干燥时间。     

具有预制孔隙多孔介质冷冻干燥的多相传递模型

基于局部质量非平衡假设,建立了多相多孔介质热、质耦合传递数学模型,理论验证具有预制孔隙的初始非饱和多孔物料对冷冻干燥过程的强化作用。模型考虑了多孔介质的吸湿效应,构建了3种吸附-解吸平衡关系。模型使用基于有限元法的COMSOL Multiphysics软件平台数值求解,并与实验数据进行了比较。结果表明,初始非饱和冷冻物料能够有效地强化冷冻干燥过程。采用不同函数形式的吸附-解吸平衡关系模拟的干燥曲线均与实验数据非常吻合。通过分析物料内部的饱和度、温度和质量源分布,探讨了初始非饱和物料冷冻干燥过程的传热传质机理。初始非饱和物料的干燥速率控制因素主要是传热。模拟考察环境辐射温度对冷冻干燥过程影响的结果表明,所建模型具有良好的预测能力。     

具有预制孔隙多孔介质冷冻干燥的多相传递模型

基于局部质量非平衡假设,建立了多相多孔介质热、质耦合传递数学模型,理论验证具有预制孔隙的初始非饱和多孔物料对冷冻干燥过程的强化作用。模型考虑了多孔介质的吸湿效应,构建了3种吸附-解吸平衡关系。模型使用基于有限元法的COMSOL Multiphysics软件平台数值求解,并与实验数据进行了比较。结果表明,初始非饱和冷冻物料能够有效地强化冷冻干燥过程。采用不同函数形式的吸附-解吸平衡关系模拟的干燥曲线均与实验数据非常吻合。通过分析物料内部的饱和度、温度和质量源分布,探讨了初始非饱和物料冷冻干燥过程的传热传质机理。初始非饱和物料的干燥速率控制因素主要是传热。模拟考察环境辐射温度对冷冻干燥过程影响的结果表明,所建模型具有良好的预测能力。     

初始非饱和多孔物料冷冻干燥的数值模拟

为了提高冷冻干燥过程的经济性,本文主要对初始非饱和物料的冷冻干燥过程进行数值模拟。建立了二维含湿多孔介质冷冻干燥数学模型,使用COMSOL Multiphysics 4.3a软件进行求解。液体物料的主要溶质为甘露醇。提出两种新的吸附-解吸平衡关系,并与实验数据进行了对比,分析了其适用条件。结果显示,初始非饱和冷冻物料能够有效减少干燥时间,模拟结果与实验数据吻合良好。通过分析物料内部温度、饱和度分布得知,升华界面随着干燥过程的进行逐渐向物料内部转移,干燥过程也发生在物料冰冻区域。适当提高环境温度有利于强化整个干燥过程。     

初始非饱和多孔物料对冷冻干燥过程的影响

提出了“初始非饱和多孔物料冷冻干燥”的思想,从实验上验证具有一定初始孔隙的非饱和多孔物料对液体物料冷冻干燥过程的强化作用。设计、加工和组装了一套实验室规模的多功能冷冻干燥装置。采用“液氮制作冰激凌法”,将以甘露醇为主要溶质的液体物料制备成具有不同初始孔隙的冷冻物料。对于相同质量和相同湿含量的非饱和冷冻物料,在相同的操作条件下,进行冷冻干燥实验,并与常规冷冻干燥相比较。结果表明,初始非饱和物料对冷冻干燥过程确实具有显著的强化作用。非饱和冷冻物料(初始饱和度0.28)的干燥时间比常规冷冻物料(初始饱和度1.00)能够节省36.4%。初始饱和度越小,干燥时间越短,干燥产品的含水率越低。     

吸湿多孔介质冷冻干燥传质传热模型

本研究在作者提出的吸附—解吸平衡关系的基础上,建立了一个全新的考虑吸湿效应的多孔介质冷冻干燥数学模型。模型用有限差分法进行求解,并带有一个移动边界,以模拟介电材料辅助的微波冷冻干燥过程。介电材料选用碳化硅（SiC）,原料液为脱脂奶。模拟结果表明：介电材料能够有效强化微波冷冻干燥过程。在典型操作条件下,介电材料辅助的微波冷冻干燥所用的时间比普通微波冷冻干燥减少33.1%。当料液中固体含量较低或者固体产品的损耗因子较小时,介电材料对微波加热的效果不明显。基于冰饱和度、温度和水蒸气浓度的分布,本文分析了干燥过程中的传质传热机理,并对干燥速率控制因素进行了讨论。     

吸波材料辅助的初始非饱和物料微波冷冻干燥

为了强化冷冻干燥过程,制备咖啡溶液的初始饱和与非饱和2种冷冻样品,分别使用石英与碳化硅底盘进行常规和微波冷冻干燥实验,同时采用电阻法测定溶液的共晶温度.结果表明,在温度为25℃、压力为22 Pa时采用石英底盘,初始非饱和物料冷冻干燥时间比饱和物料缩短了14.9％,适当提高操作温度可以强化冷冻干燥过程.在25℃、22 P...     

Numerical Investigation on Dielectric Material Assisted Microwave Freeze-Drying of Aqueous Mannitol Solution

The dielectric material assisted microwave freeze-drying was investigated theoretically in this study. A coupled heat and mass transfer model was developed considering distributions of the temperature, ice saturation and vapor mass concentration inside the material being dried, as well as the vapor sublimation-desublimation in the frozen region. The effects of temperature and saturation on the effective conductivities were analyzed based on heat and mass flux equations. The model was solved numerically by the variable time-step finite-deference technique with two movable boundaries in an initially unsaturated porous sphere frozen from an aqueous solution of mannitol. The sintered silicon carbide (SiC) was selected as the dielectric material. The results show that dielectric material can significantly enhance microwave freeze-drying process. For case of the dielectric field strength, E = 4000 V/m under typical operating conditions, the drying time is 2081 s, 30.1% shorter and 47.2% longer, respectively, than those for E = 2000V/m and E = 6000 V/m. The heat and mass transfer mechanisms during the drying process were discussed.     

Numerical Investigation on Dielectric Material Assisted Microwave Freeze-Drying of Aqueous Mannitol Solution

Abstract

The dielectric material assisted microwave freeze-drying was investigated theoretically in this study. A coupled heat and mass transfer model was developed considering distributions of the temperature, ice saturation and vapor mass concentration inside the material being dried, as well as the vapor sublimation-desublimation in the frozen region. The effects of temperature and saturation on the effective conductivities were analyzed based on heat and mass flux equations. The model was solved numerically by the variable time-step finite-deference technique with two movable boundaries in an initially unsaturated porous sphere frozen from an aqueous solution of mannitol. The sintered silicon carbide (SiC) was selected as the dielectric material. The results show that dielectric material can significantly enhance microwave freeze-drying process. For case of the dielectric field strength, E = 4000 V/m under typical operating conditions, the drying time is 2081 s, 30.1% shorter and 47.2% longer, respectively, than those for E = 2000V/m and E = 6000 V/m. The heat and mass transfer mechanisms during the drying process were discussed.     

Effect of Dielectric Material on Microwave Freeze Drying of Skim Milk

Abstract:

A simultaneous heat and mass transfer model of the dielectric material–assisted microwave freeze drying was derived in this study considering the vapor sublimation-desublimation in the frozen region. The mathematical model was solved numerically by using the finite-difference technique with two moving boundaries. Silicon carbide (SiC) was selected as the dielectric material, and the skim milk was used as the representative solid material in the aqueous solution to be freeze-dried. The results show that the dielectric material can significantly enhance the microwave freeze drying process. The drying time is greatly reduced compared to cases without the aid of the dielectric material. Profiles of the temperature, ice saturation, vapor concentration, and pressure during freeze drying were presented. Mechanisms of the heat and mass transfer inside the material sphere were analyzed. For an initially unsaturated frozen sample of 16 mm in diameter with a 4-mm-diameter dielectric material core, the drying time is 288.2 min, much shorter than 380.1 min of ordinary microwave freeze drying and 455.0 min of conventional vacuum freeze drying, respectively, under typical operating conditions.     

具有预制孔隙多孔物料的冷冻干燥

实验探究了具有初始预制孔隙多孔物料对冷冻干燥过程的强化作用。以注射用抗生素药剂--头孢曲松钠为主要溶质,采用“液氮制作冰激凌法”制备了具有不同初始孔隙率的冷冻物料,在相同的条件下进行冷冻干燥实验。结果表明,初始饱和度为0.3的冷冻物料（初始孔隙率为0.67）干燥时间比饱和物料（初始孔隙率为0）缩短了21.3%。干燥产品的SEM图显示,初始非饱和冷冻物料的固体骨架和孔隙结构连续而均匀,初始饱和度越低,骨架越纤细,可大大地降低传质阻力。对冷冻速率和退火处理的研究表明,冷冻速率对于两种物料干燥过程的影响甚微;退火处理能够提高冷冻干燥速率。适当提高操作温度可以明显缩短两种物料的干燥时间;操作压力对冷冻干燥过程几乎没有影响。     

Theoretical Study on Microwave Freeze-Drying of an Aqueous Pharmaceutical Excipient with the Aid of Dielectric Material

Abstract

A mathematic model of simultaneous heat and mass transfer for the dielectric material assisted microwave freeze-drying was derived and solved numerically using the finite-deference technique with two moving boundaries. Lactose, a typical pharmaceutical excipient, was used as the representative solid material in the aqueous solution to be freeze-dried. Silicon carbide (SiC) was selected as the dielectric material. Numerical results show that the dielectric material can significantly enhance the microwave freeze-drying process. Under typical operating conditions, the drying time is 43% shorter than that of ordinary microwave freeze-drying. Temperature variations at sublimation fronts were examined in order to determine the appropriate microwave power input. Profiles of temperature, ice saturation, vapor concentration, and pressure during freeze-drying are presented, and rate-controlling mechanisms are discussed.     

Heat and mass transfer model of dielectric-material-assisted microwave freeze-drying of skim milk with hygroscopic effect

A new porous media mathematical model for freeze-drying was developed based on the adsorption-desorption relationship proposed in this paper. A finite difference solution was obtained from a moving boundary problem for the dielectric-material-assisted microwave freeze-drying process. Silicon carbide (SiC) was selected as the dielectric material; and frozen skim milk was used as the aqueous solution to be dried. Simulation results showed that the dielectric material can significantly enhance the microwave freeze-drying process. The drying time was 33.1% shorter than that of ordinary microwave freeze-drying under typical operating conditions. When the solid content of the solution to be freeze-dried was very low, or the solid product had a very small loss factor, microwave heating was less effective without the assistance of dielectric material. The mechanisms of heat and mass transfer during drying were analyzed based on profiles of ice saturation, temperature and vapor concentration. Drying rate-controlling factors were discussed. A comparison was made between the model predictions and the reported experimental data.