Impedance analysis of PLD LiNi0.8Co0.2O2 film electrode

The kinetics of intercalation are discussed using a pulsed laser deposition (PLD) film electrode and electrochemical impedance analysis. Films of LiNi_0.8Co_0.2O₂, deposited on single crystal substrates, were used for the study. The films have intercalative or blocking orientations on different crystal surfaces of the substrates. Impedance spectra show that there are at least three elemental processes in intercalation. Two processes at higher frequencies suggest that they occur at the electrode surface and are influenced by the orientation of the film. The third process appearing at low frequencies below 1 Hz indicates lithium motion in the bulk structure and shows the largest resistance among the three processes. This lithium conduction in a thin PLD film shows a semicircular response and is considered to be influenced more by the structure due to the nanometer-scale thickness.     

State of charge (SOC) dependence of lithium carbonate on LiNi0.8Co0.15Al0.05O2 electrode for lithium-ion batteries

Lithium-ion batteries using LiNi_0.8Co_0.15Al_0.05O₂ (NCA) as the positive electrode material and hard carbon as the negative electrode material with electrolyte of mixture of ethylene carbonate and dimethyl carbonate containing LiPF₆ were fabricated, and the surface materials on the positive electrode were observed by ATR spectroscopy of FT-IR measurement. Lithium carbonate was mainly observed as the surface material and the intensity of IR absorption peaks were depended on state of charge (SOC) of the batteries. The result suggests that the amount of lithium carbonate increases by discharge and decreases by charge.     

Electrochemical performance of In2O3 thin film electrode in lithium cell

Indium oxide (In₂O₃) coating on Pt, as an electrode of thin film lithium battery was carried out by using cathodic electrochemical synthesis in In₂(SO₄)₃ aqueous solution and subsequently annealing at 400 °C. The coated specimens were characterized by X-ray photoelectron spectroscopy (XPS) for chemical bonding, X-ray diffraction (XRD) for crystal structure, scanning electron microscopy (SEM) for surface morphology, cyclic voltammetry (CV) for electrochemical properties, and charging/discharging test for capacity variations. The In₂O₃ coating film composed of nano-sized particles about 40 nm revealing porous structure was used as the anode of a lithium battery. During discharging, six lithium ions were firstly reacted with In₂O₃ to form Li₂O and In, and finally the Li_4.33In phase was formed between 0.7 and 0.2 V, revealing the finer particles size about 15 nm. The reverse reaction was a removal of Li⁺ from Li_4.33In phase at different oxidative potentials, and the rates of which were controlled by the thermodynamics state initially and diffusion rate finally. Therefore, the total capacity was increased with decreasing current density. However, the cell delivering a stable and reversible capacity of 195 mAh g⁻¹ between 1.2 and 0.2 V at 50 μA cm⁻² may provide a choice of negative electrode applied in thin film lithium batteries.     

Preparation of LiNi0.80Co0.15Al0.05O2 cathode material via Li-rich method

本文采用共沉淀法制备球形Ni_0.80Co_0.15Al_0.05(OH)_2.05前驱体,经预氧化后,采用富锂配比在氧气和空气气氛下烧结合成LiNi_0.80Co_0.15Al_0.05O₂正极材料.用X射线衍射,扫描电镜和恒电流充放电测试等方法对该材料的结构,形貌及电化学性能进行表征.结果表明:当锂配比为1.15时,氧气和空气中烧结合成的LiNi_0.80Co_0.15Al_0.05O₂正极材料的形貌,结构和电化学性能相当.富锂配比方法可在空气气氛下制备出电化学性能优异的LiNi_0.80Co_0.15Al_0.05O₂正极材料.0.1 C放电克比容量在200 mA·h/g以上,首次效率在87%左右;1 C放电克比容量在168 mA·h/g以上;800周循环容量保持率在80%以上.     

Preparation and electrochemical characteristics of LiNi1/3Mn1/3Co1/3O2 coated with metal oxides coating

LiNi_1/3Mn_1/3Co_1/3O₂ prepared by a spray drying method exhibited poor cyclic performance when it was operated at rates of 0.5C and 2C in 3–4.6 V. A metal oxide (ZrO₂, TiO₂, and Al₂O₃) coating (3 wt%) could effectively improve its cyclic performance at both 0.5C and 2C. Electrochemical impedance spectroscopy (EIS) studies suggested that both the surface resistance and the charge transfer resistance of the bare LiNi_1/3Mn_1/3Co_1/3O₂ significantly increase after 100 cycles, whose origin is mainly related to the change in both the particle surface and electrode morphologies. The presence of a thin metal oxide layer could remarkably suppress the increase in the total resistance (sum of the surface resistance and the charge transfer resistance), which was attributed to the improvement in good cyclic performances.     

The effect of Ni content on a highly active Ni-Al2O3 catalyst prepared by the homogeneous precipitation method

Highly active Ni-Al₂O₃ catalysts were prepared by the homogeneous precipitation method with a variety of high nickel contents ranging from 30 to 70 wt.%. The effects of nickel content on the physicochemical properties and catalytic activities of the Ni-Al₂O₃ catalysts were investigated. XRD measurements showed that the catalyst with 30 Ni wt.% only had a diffraction peak corresponding to NiAl₂O₄, whereas the catalysts of 50, 60 and 70 Ni wt.% had diffraction peaks corresponding to NiO and NiAl₂O₄. Hydrogen chemisorption results showed that the nickel surface area increased with increasing nickel content in the order: 30 < 40 < 50 < 60 < 70 Ni wt.%. Specifically, the nickel surface area increased steadily from 11 to 22 m²/g with increasing the nickel content from 30 to 50 wt.%, after which it stayed nearly constant at 22 m²/g despite the increase in nickel content from 50 to 70 wt.%. TEM images of the reduced Ni-Al₂O₃ catalysts revealed that the average sizes of the Ni particles were 12, 13 and 16 nm for the catalysts with 30, 50 and 70 Ni wt.%, respectively, suggesting that a higher nickel content yielded a larger Ni particle. The catalytic performance of methane steam reforming showed that the catalytic reaction rate increased steadily with increasing nickel content from 30 to 50 wt.%, after which it stayed nearly constant despite that the nickel content increased to over 50 wt.%. As a result, about 50 wt.% of nickel was found to be a reasonable nickel content to obtain the maximum catalytic activity.     

Reforming of bioethanol over Ni/Al2O3 and Ni/CeZrO2/Al2O3 catalysts in supercritical water for hydrogen production

Bioethanol was reformed in supercritical water (SCW) at 500 °C and 25 MPa on Ni/Al₂O₃ and Ni/CeZrO₂/Al₂O₃ catalysts to produce high-pressure hydrogen. The results were compared with non-catalytic reactions. Under supercritical water and in a non-catalytic environment, ethanol was reformed to H₂, CO₂ and CH₄ with small amounts of CO and C2 gas and liquid products. The presence of either Ni/Al₂O₃ or Ni/CeZrO₂/Al₂O₃ promoted reactions of ethanol reforming, dehydrogenation and decomposition. Acetaldehyde produced from the decomposition of ethanol was completely decomposed into CH₄ and CO, which underwent a further water-gas shift reaction in SCW. This led to great increases in ethanol conversion and H₂ yield on the catalysts of more than 3-4 times than that of the non-catalytic condition. For the catalytic operation, adding small amounts of oxygen at oxygen to ethanol molar ratio of 0.06 into the feed improved ethanol conversion, at the expense of some H₂ oxidized to water, resulting in a slightly lower H₂ yield. The ceria-zirconia promoted catalyst was more active than the unpromoted catalyst. On the promoted catalyst, complete ethanol conversion was achieved and no coke formation was found. The ceria-zirconia promoter has important roles in improving the decomposition of acetaldehyde, the enhancement of the water-gas shift as well as the methanation reactions to give an extremely low CO yield and a tremendously high H₂/CO ratio. The SCW environment for ethanol reforming caused the transformation of gamma-alumina towards the corundum phase of the alumina support in the Ni/Al₂O₃ catalyst, but this transformation was slowed down by the presence of the ceria-zirconia promoter.     

Synthesis and electrochemical studies on Al2O3 coated LiNi0.5Co0.44Fe0.06VO4 for lithium ion batteries

LiNi_0.5Co_0.44Fe_0.06VO₄ cathode material has been synthesized by a citric acid:polyethylene glycol polymeric method at 723 K for 5 h in air. The surface of the LiNi_0.5Co_0.44Fe_0.06VO₄ was coated with various wt.% of Al₂O₃ by a wet chemical procedure and heat treated 873 K for 2 h in air. The samples were characterized by XRD, FTIR, SEM, and TEM techniques. XRD patterns expose that the complete crystalline phase occurred at 723 K and there was no indication of new peaks for the coated samples. FTIR spectra show that the complete removal of organic residues and the formation of LiNi_0.5Co_0.44Fe_0.06VO₄. TG/DTGA results reveal that the formation of LiNi_0.5Co_0.44Fe_0.06VO₄ occurred between 480 and 670 K and the complete crystalline occurred at 723 K. SEM micrographs show the various morphological stages of the polymeric intermediates. TEM micrographs of the pristine LiNi_0.5Co_0.44Fe_0.06VO₄ reveal that the particle size ranged from 130 to 150 nm and Al₂O₃ coating on the fine particles was compact and had an average thickness of about 15 nm. The charge–discharge experiments were carried out between 2.8 and 4.9 V (versus Li) at a current rate of 0.15 C. The 1.0 wt.% Al₂O₃ coated sample had the best electrochemical performance, with an initial capacity of 65 mAh g⁻¹ and capacity retention of 60% after 50 cycles. The electrochemical impedance behavior suggests that the failure of pristine cathode performance is associated with an increase in the impedance growth on the surface of the cathode material upon continuous cycling.     

Electrode performance of a new La0.6Sr0.4Co0.2Fe0.8O3 coated cathode for molten carbonate fuel cells

To improve the cathode performance in molten carbonate fuel cells (MCFCs), Lanthanum Strontium Cobalt Ferrite (La_0.6Sr_0.4Co_0.2Fe_0.8O₃, LSCF) of perovskite structure was coated on a porous Ni plate by a vacuum suction method. The electrochemical performance of modified cathode was examined and compared with that of uncoated conventional cathode via single cell operation and electrochemical impedance analysis (EIS). The cell voltage of the single cell using the LSCF coated cathode, measured at 650 °C with current density of 150 mA/cm² is 0.837 V and it is higher than that of the cell with uncoated conventional cathode, 0.805 V. The higher performance and the lower charge transfer resistance were obtained at 600–700 °C after LSCF coating. The lower activation energy of oxygen reduction reaction was also obtained. The lower activation energy of oxygen reduction reaction after LSCF coating shows that LSCF on lithiated NiO cathode plays a role of catalyst on the oxygen reduction reaction in cathode.     

A highly active catalyst, Ni/Ce–ZrO2/θ-Al2O3, for on-site H2 generation by steam methane reforming: pretreatment effect

The steam treatment effect has been investigated over the doubly impregnated catalyst, Ni/Ce–ZrO₂/θ-Al₂O₃, in steam methane reforming (SMR). The catalyst was remarkably deactivated by steam treatment but reversibly regenerated by H₂-reduction. XRD results showed that the steam treatment resulted in the formation of NiAl₂O₄ which is inactive for SMR but it was reversibly converted to Ni by the reduction. The reversible oxidation-reduction of Ni state was also evidenced by XPS and it was observed that the formation of NiAl₂O₄ is more favorable at higher temperature. It is most likely that the alumina support is only partially covered with Ce–ZrO₂ and most Ni directly interacts with θ-Al₂O₃ which would probably make easy formation of NiAl₂O₄ in the presence of steam alone. The results imply that, during the start-up procedure in SMR, too high concentration of steam could deactivate seriously Al₂O₃ supported Ni catalysts.     

Characteristics of alkali-resistant Ni/MgAl2O4 catalyst for direct internal reforming molten carbonate fuel cell

Direct internal reforming – molten carbonate fuel cell (DIR–MCFC) has advantages of higher efficiency and smaller size. However, deactivation of the catalyst by alkali carbonate electrolytes poses a significant problem in MCFC. To solve this problem, Ni/MgO and Ni/MgAl₂O₄ catalysts were compulsively mixed with a eutectic mixture of Li₂CO₃ and Na₂CO₃ prior to a methane steam reforming activity test. Activity of Ni/MgO rapidly decreased, while that of Ni/MgAl₂O₄ remained steady due to good alkali resistance. To analyze the effects of alkali addition, N₂ adsorption-desorption, X-ray diffraction, temperature-programmed reduction and oxidation, scanning electron microscopy, and X-ray photoelectron spectroscopy experiments were carried out. Both Ni/MgO and Ni/MgAl₂O₄ showed sintering of Ni and blocking of pores, which reduced the catalytic activity. However, Ni/MgAl₂O₄ showed other positive effects such as stronger metal–support interaction and increased dissociative adsorption.     

Dynamic behavior of surface film on LiCoO2 thin film electrode

Electrochemical oxidation behavior of non-aqueous electrolytes on LiCoO₂ thin film electrodes were investigated by in situ polarization modulation Fourier transform infrared (PM-FTIR) spectroscopy, atomic force microscopy and X-ray photoelectron spectroscopy (XPS). LiCoO₂ thin film electrode on gold substrate was prepared by rf-sputtering method. In situ PM-FTIR spectra were obtained at various electrode potentials during cyclic voltammetry measurement between 3.5 V vs. Li/Li⁺ and 4.2 V vs. Li/Li⁺. During anodic polarization, oxidation of non-aqueous electrolyte was observed, and oxidized products remained on the electrode at the potential higher than 3.75 V vs. Li/Li⁺ as a surface film. During cathodic polarization, the stripping of the surface film was observed at the potential lower than 3.9 V vs. Li/Li⁺. Depth profile of XPS also showed that more organic surface film remained on charged LiCoO₂ than that on discharged one. AFM images of charged and discharged electrodes showed that some decomposed products deposited on charged electrode and disappeared from the surface of discharged one. These results indicate that the surface film on LiCoO₂ is not so stable.     

Interfacial lithium-ion transfer at the LiMn2O4 thin film electrode/aqueous solution interface

Interfacial lithium-ion transfer at the LiMn₂O₄ thin film electrode/aqueous solution was investigated. The cyclic voltammograms of the film electrode conducted in the aqueous solution was similar to an adsorption-type voltammogram of reversible system, suggesting that fast charge transfer reaction proceed in the aqueous solution system. We found that the activation energy for this interfacial lithium-ion transfer reaction obtains 23–25 kJ mol⁻¹, which is much smaller than that in the propylene carbonate solution (50 kJ mol⁻¹). This small activation energy will be responsible for the fast interfacial lithium-ion transfer reaction in the aqueous solution. These results suggest that fast lithium insertion/extraction reaction can be realized by decreasing the activation energy for interfacial lithium-ion transfer reaction.     

Evaluation of Ni/Y2O3/Al2O3 catalysts for hydrogen production by autothermal reforming of methane

Ni/xY₂O₃–Al₂O₃ (x = 5, 10, 15, 20 wt%) catalysts were prepared by sequential impregnation synthesis. The catalytic performance for the autothermal reforming of methane was evaluated and compared with Ni/γ-Al₂O₃ catalyst. The physicochemical properties of catalysts were characterized by X-ray diffraction (XRD), Transmission electron microscope (TEM), X-Ray Photoelectron Spectrometer (XPS), Thermo Gravimetric Analyzer (TGA) and H₂-temperature programmed reduction techniques (TPR). The decrease of nickel particle size and the change of reducibility were found with Y modification. The CH₄ conversion increased with elevating levels of Y₂O₃ from 5% to 10%, then decreased with Y content from 10% to 20%. Ni/xY₂O₃–Al₂O₃ catalysts maintained high activity after 24 h on stream, while Ni/Al₂O₃ had a significant deactivation. The characterization of spent catalysts indicated that the addition of Y retarded Ni sintering and decreased the amount of coke.     

A comparative study of electrodes comprising nanometric and submicron particles of LiNi0.50Mn0.50O2, LiNi0.33Mn0.33Co0.33O2, and LiNi0.40Mn0.40Co0.20O2 layered compounds

In this paper we compare the behavior of LiNi_0.5Mn_0.5O₂, LiNi_0.33Mn_0.33Co_0.33O₂ (NMC) and LiNi_0.4Mn_0.4Co_0.2O₂ as cathode materials for advanced rechargeable Li-ion batteries. These materials were prepared by a self-combustion reaction (SCR) from the metal nitrates and sucrose, followed by calcination at elevated temperatures. The temperature and duration of calcination enabled the adjustment of the average particle size and size distribution. It was established that the annealing temperature (700–900 °C) of the as-prepared oxides influences strongly the crystallite and particle size, the morphology of the material, and the electrochemical performance of electrodes in Li-cells. Capacities up to 190, 180 and 170 mAh g⁻¹ could be obtained with Li[NiMn]O₂, LiNi_0.4Mn_0.4Co_0.2O₂ and LiNi_0.33Mn_0.33Co_0.33O₂, respectively. In terms of rate capability, the order of these electrodes is NMC < LiNi_0.4Mn_0.4Co_0.2O₂ ? Li[NiMn]O₂. Many hundreds of cycles at full DOD could be obtained with Li[NiMn]O₂ and NMC electrodes in Li-cells, at room temperature. All of these materials develop a unique surface chemistry that leads to their passivation and stabilization in standard electrolyte solutions (alkyl carbonates/LiPF₆). The surface chemistry was studied by FTIR, XPS and Raman spectroscopy and is discussed herein.     

Investigation of layered Ni0.8Co0.15Al0.05LiO2 in electrode for low-temperature solid oxide fuel cells

A symmetrical cell composed of Ce_0.9Gd_0.1O_2?δ electrolyte is constructed with 0.5 mm thickness and Ni_0.8Co_0.15Al_0.05LiO₂ (NCAL)-foam Ni composite electrodes. Electrochemical performance of the cell and electrochemical impedance spectra (EIS) are measured using the three-electrode method. The maximum power densities of the cell are 93.6 and 159.7 mW cm^?2 at 500 and 550 °C, respectively. The polarization resistances of the cathode are 0.393 and 0.729 Ω cm^?2 at 550 and 500 °C, indicating that NCAL has good ORR activity. HT-XRD results for NCAL do not show phase transitions or any additional new phases at elevated temperatures, indicating that NCAL has a stable phase structure. The surface characteristics of the NCAL powders are studied by XPS and FTIR. The results reveal that Li₂CO₃ and the cation-disordered “NiO-like” phase are formed on the surface of the layered NCAL structure due to prolonged exposure to air and contain a large number of oxygen vacancies. The cation-disordered “NiO-like” phase and Li₂CO₃ composite in the melt and partial melt states in the high temperature region are considered to possess very high ionic conductivity and lower activation energy for oxygen reduction reactions.     

A screen-printed Ce0.8Sm0.2O1.9 film solid oxide fuel cell with a Ba0.5Sr0.5Co0.8Fe0.2O3−δ cathode

Screen-printing technology was developed to fabricate Ce_0.8Sm_0.2O_1.9 (SDC) electrolyte films onto porous NiO–SDC green anode substrates. After sintering at 1400 °C for 4 h, a gas-tight SDC film with a thickness of 12 μm was obtained. A novel cathode material of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ was subsequently applied onto the sintered SDC electrolyte film also by screen-printing and sintered at 970 °C for 3 h to get a single cell. A fuel cell of Ni–SDC/SDC (12 μm)/Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ provides the maximum power densities of 1280, 1080, 670, 370, 180 and 73 mW cm⁻² at 650, 600, 555, 505, 455 and 405 °C, respectively, using hydrogen as fuel and stationary air as oxidant. When dry methane was used as fuel, the maximum power densities are 876, 568, 346 and 114 mW cm⁻² at 650, 600, 555 and 505 °C, respectively. The present fuel cell shows excellent performance at lowered temperatures.     

Rapid formation of transparent CuAlO2 thin film by thermal annealing of Cu on Al2O3

An 850-nm-thick CuAlO₂ film was formed by solid state reaction of evaporated thin film Cu on c-cut Al₂O₃ (sapphire) at 1200 °C for reaction times as short as 10 min. X-ray diffractogram confirms the formation of (0 0 l) CuAlO₂, indicating oriented growth of CuAlO₂ on c-cut Al₂O₃. Fourier transformation infra-red (FTIR) spectra showed peaks corresponding to Cu-O, Al-O and O-Cu-O bonds, confirming further the CuAlO₂ phase formation. UV-visible spectrum measurement showed high transparency of the film in the visible region with a direct band gap of 3.25 eV. The mechanism of the formation of the film is discussed.     

LiMn2O4 electrode prepared by gold–titanium codeposition with improved cyclability

An LiMn₂O₄ electrode was prepared based on mixed-metals (gold–titanium) codeposition method. By this method, titanium oxide is also incorporated into the electroactive film formed on substrate electrode. Formation of titanium oxide on the spinel surface avoids dissolution of Mn from the spinel at elevated temperatures. TiO₂can act as a bridge between the spinel particles to reduce the interparticle resistance and as a good material for the Li intercalation/deintercalation. Thus, electrochemical performance of the LiMn₂O₄ spinel can be improved by the surface modification with TiO₂. This action improves cyclability for lithium battery performance and reduces capacity fades of LiMn₂O₄ at elevated temperatures.     

Electrochemical thermal stability of the LiFePO4/LiNi0.8Co0.15Al0.05O2 blend cathode material for lithium ion batteries

为了改善LiNi_0.8Co_0.15Al_0.05O₂正极材料的电化学热稳定性能,加入LiFePO₄共混制成了LiFePO₄/LiNi_0.8Co_0.15Al_0.05O₂锂离子电池用混合正极材料。使用X射线衍射（XRD）和扫描电子显微镜（SEM）表征了结构和形貌,测试了电化学性能。结果显示,简单球磨的混合LiFePO₄/LiNi_0.8Co_0.15Al_0.05O₂正极材料中,纳米LiFePO₄粒子包覆在LiNi_0.8Co_0.15Al_0.05O₂粒子表面提高了混合正极材料在充放电过程中的电化学稳定性和结构稳定性。LiFePO₄/LiNi_0.8Co_0.15Al_0.05O₂混合正极材料在50 ℃下循环100周容量保持率为82.0%,明显地优于单一LiNi_0.8Co_0.15Al_0.05O₂材料的72.9%。