共查询到20条相似文献,搜索用时 125 毫秒
1.
本文指出了通过对丙烯腈装置回收塔系统不断摸索与优化,提出了在保证产品质量的条件下通过低控回收塔顶压,实现节约回收塔釜再沸器蒸汽耗量、丙烯腈装置节能降耗的目的. 相似文献
2.
3.
4.
《化工科技》2018,(5)
通过在丙烯腈装置吸收塔釜液泵入口管线和一效蒸发器循环线加入分散剂,避免聚合物结垢并附着在换热器内,提高回收塔原料预热器、回收塔再沸器以及四效蒸发器的换热效果。研究结果表明,分散剂以4.64kg/h流量加入吸收塔釜液泵入口管线上,回收塔进料温度调节阀阀位由10%提高至75%,回收塔进料温度达到工艺控制指标(65℃),回收塔再沸器蒸汽消耗降低10t/h;分散剂以3.48kg/h流量加入在一效蒸发器循环线上,四效系统蒸发率由66%提高至74%。说明分散剂的加入能有效地阻止系统内聚合物聚集和累积,显著提高了换热器的换热效率,延长了装置的运行周期,降低了能耗,提高了生产效率。 相似文献
5.
6.
7.
8.
顺丁烯腈是丙烯腈生产中的副产物,其含量对丙烯腈下游产品质量和能耗有着重要影响。通过控制反应负荷、空比(空气与丙烯的体积比)、回收塔溶剂水温度、进料温度以及灵敏板温度等工艺手段可以控制丙烯腈产品中w(顺丁烯腈)。结果表明:反应器丙烯投料量由8 000m3/h降至7 100m3/h,丙烯腈产品中w(顺丁烯腈)由43mg/kg降至13mg/kg;反应空比由9.3降至8.9,丙烯腈产品中w(顺丁烯腈)由87mg/kg降至10mg/kg,且进一步降低空比,对w(顺丁烯腈)无影响;回收塔灵敏板温度由85.5℃降至82℃,丙烯腈产品中w(顺丁烯腈)由90mg/kg降至12mg/kg;回收塔溶剂水温度由45℃降至41℃,丙烯腈产品中w(顺丁烯腈)由72mg/kg降至15mg/kg;回收塔进料温度由65℃降至62℃,丙烯腈产品中w(顺丁烯腈)由54mg/kg降至20mg/kg,满足了丙烯腈下游产品——丙烯酰胺的使用要求。 相似文献
9.
10月8日8时整,安庆石化丙烯腈装置按计划切断反应器进料,进入了为期11天的装置检修阶段。此次装置停工检修以更换催化剂为主线,并对反应器、吸收塔、回收塔等塔器内部件进行检查,清洗冷换设备,更换与改造部分设备及管线,以及现场漏点消缺等,计划检修时间为11天,时间紧、任务重。 相似文献
10.
统计了目前国内丙烯腈行业在运丙烯腈装置的废水焚烧情况,对丙烯腈废水焚烧的重要性和难点进行了分析。随着国家环保要求及人民环境要求的不断提高,要求丙烯腈装置必须实现环保达标排放。所有丙烯腈装置均需要配建新型废水焚烧炉,并实现达标排放。激烈的市场竞争要求相关厂家不断优化废水焚烧装置运行工况,提高其运行的安全性、平稳性和经济性。 相似文献
11.
乙烯酮(双乙烯酮)是十分重要的化工中间体,其下游产品较多。江苏某化工厂开发生产乙烯酮(双乙烯酮)下游产品三十多个,年生产规模三万多吨,是国内以乙烯酮(双乙烯酮)为中间体生产精细化学品的综合骨干企业。针对乙烯酮(双乙烯酮)下游产品废水特点,该厂结合企业实际,开展了产品优化,结构调整,清洁生产,资源循环利用,节水降耗等工作,从源头削减了污染物的生产。同时投资二千多万元新建预处理装置三套,6000m3/d废水生化处理装置一套,使全厂乙烯酮(双乙烯酮)下游产品的废水得到了有效的治理。 相似文献
12.
13.
14.
利用组件技术开发化工原理实验课件,给出了系统层、组件库层和应用层的架构划分。重点讨论了组件库的设计,给出了流体阻力这一典型实验的实现描述。实践证实,基于组件技术可以提高仿真实验的开发效率。 相似文献
15.
我厂3号回转窑(Φ4m×60m)生产线在1996年年底由SP窑(产量912t/d)改为NSP窑(产量1320t/d),预分解系统为四级旋风预热器带离线式分解炉 相似文献
17.
The miscibility of various amorphous polybutadienes with mixed microstructures of 1,4 addition units (cis, 1,4 and trans 1,4) and 1,2 addition units have been investigated. The studies here involved optical transparency, differential scanning calorimetry, and small angle light scattering. It was found that a 90 percent (cis) 1, 4 addition polybutadiene was immiscible with high (91 percent) 1,2 addition polybutadiene. Reduction of the 1,2 content to 71 percent induced an upper critical solution temperature (UCST) with the cis 1,4 polymer. Polybutadienes with 50 percent and 10 percent 1,2 contents were miscible above the crystalline melting temperature of the cis 1,4 polybutadiene. Immiscibility of the 91 percent 1,2 addition polymer was also found with a 10 percent 1,2 polybutadiene. The latter polymer also exhibits an UCST with the 71 percent 1,2 polymer. The results are used to interpret the characteristics of blends of polybutadienes of varying microstructure. 相似文献
18.
以F类粉煤灰为例,详细介绍了测定粉煤灰中烧失量的步骤、计算数学模型、影响测量不确定度的因素以及各项测量不确定度分量评定,人员、设备、材料、方法、环境都是影响测量不确定的因素。 相似文献
19.
20.
Based on the filtration equations with account of heat transfer in the heating region, the problem of instability of small
perturbations of the wave front of filtration combustion of a gas is solved. Expressions for the growth decrement and critical
transverse size of a perturbation are obtained. The problem of the wave-front stability is solved with account of the macroscopic
redistribution of filtration in the system. The solution includes macroscopic characteristics such as the transverse size,
the width of the high-temperature zone, etc. A method is proposed for taking into account the influence of the characteristics
of the system on the evolution of perturbations. It is shown that small deformation perturbations of the front always increase
to a certain amplitude; their subsequent development— continuation of their growth or stabilization—is determined by the characteristics
of the system.
Translated fromFizika Goreniya i Vzryva, Vol. 35, No. 5, pp. 3–5, September–October 1999. 相似文献