Preparation and mechanical properties of acrylonitrile‐butadiene‐styrene copolymer/clay nanocomposites

Bis(3‐triethoxysilylpropyl) tetrasulfane (TSS) was reacted with the silanol groups of the commercially available clay, Closite®25A (C25A) to prepare TSS‐C25A, which was melt‐compounded with acrylonitrile‐butadiene‐styrene copolymer (ABS). The tetra sulfide groups of TSS‐C25A may chemically react with the vinyl groups of ABS to enhance the interaction between the clay and ABS. The ABS/clay composites exhibited much higher tensile strength and elongation at break than the neat ABS. Especially the elongation at break of ABS/TSS‐C25A composite was 5 times higher than that of neat ABS. The X‐ray diffraction patterns of the clay showed that the d₀₀₁ basal spacing was enlarged from 1.89 nm to 2.71–2.86 nm as a result of the compounding with ABS. According to the thermogravimetric analysis, the thermal decomposition of the composite took place at a slightly higher temperature than that of neat ABS. Intercalated/exfoliated coexisting structures were observed by transmission electron microscopy for the ABS/clay composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fire performance and mechanical properties of acrylonitrile‐butadiene‐styrene copolymer/modified expandable graphite composites

The fire performance and mechanical properties of an acrylonitrile‐butadiene‐styrene (ABS) copolymer compounded with different expandable graphites (EG) and fire retardants were studied by using the limiting oxygen index test, the UL‐94 test, a mechanical test, and a thermogravimetric analysis. The ground EG treated with phosphoric acid and silane could have the great increase of the volume expansion ratio. The addition of the treated EG in ABS significantly enhances the fire performance but decreases the impact strength of ABS. ABS with the treated EG has a much higher impact strength than with the as‐received EG because of the smaller particle size of the treated EG and the better adhesion between the ABS and the treated EG. The addition of modified ammonium polyphosphate or decabromodiphenyl oxide/antimony trioxide can considerably improve the fire performance of ABS/treated EG composites because of a synergistic effect. The V‐0 grade (UL‐94) ABS composite with the limiting oxygen index of 32.5 can be obtained by adding small amounts of the treated EG and modified ammonium polyphosphate into ABS. Thermogravimetric analysis results indicate that the initial vapor release temperatures and the weight loss rates of ABS/EG composites are closely related to their fire performance and affected by the fire retardant used. Copyright © 2011 John Wiley & Sons, Ltd.     

Properties of polycarbonate/acrylonitrile‐butadiene‐styrene/talc composites

The morphology, tensile, impact properties, and thermal expansion behavior of polycarbonate (PC)/acrylonitrile‐styrene‐butadiene (ABS)/talc composites with different compositions and mixing sequences were investigated. From the studies of morphology of the PC/ABS/talc composites, it was observed that some talc particles were located in both the PC and the ABS phases of the blend but most were at the interface between the PC and ABS phases for every mixing sequence. Aspect ratios of the talc particles determined by TEM image analysis reasonably matched values computed from tensile modulus using composite theory. The thermal expansion behavior, or CTE values, was not significantly influenced by the mixing sequence. The impact strength of the PC/ABS/talc composites depended significantly on the mixing sequence; a premix with PC gave the poorest toughness. The molecular weight of the PC in PC/talc composites was found to be significantly decreased. It appears that the impact strength of the PC/ABS/talc composites is seriously compromised by the degradation of the PC caused by talc. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical and UV‐shielding properties of in situ synthesized poly(acrylonitrile‐butadiene‐styrene)/zinc oxide nanocomposites

A series of poly(acrylonitrile‐butadiene‐styrene)/ZnO nanocomposites with different ZnO nanoparticles content were synthesized by a mass‐suspension polymerization process. Nanocomposites obtained through this technique presented high impact resistance despite the presence of agglomerates for high ZnO nanoparticles content so that, these samples were subjected to twin‐screw extrusion. The extrusion led to a dramatic morphological change and increased in impact resistance, higher than 100% in most of the cases. On the other hand, the higher the ZnO content, the higher the UV blocking (>95% for 1 and 3% of ZnO) for both materials, before and after extrusion. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical and flame‐retarding properties of styrene–butadiene rubber filled with nano‐CaCO3 as a filler and linseed oil as an extender

A nanosize CaCO₃ filler was synthesized by an in situ deposition technique, and its size was confirmed by X‐ray diffraction. CaCO₃ was prepared in three different sizes (21, 15, and 9 nm). Styrene–butadiene rubber (SBR) was filled with 2–10 wt % nano‐CaCO₃ with 2% linseed oil as an extender. Nano‐CaCO₃–SBR rubber composites were compounded on a two‐roll mill and molded on a compression‐molding machine. Properties such as the specific gravity, swelling index, hardness, tensile strength, abrasion resistance, modulus at 300% elongation, flame retardancy, and elongation at break were measured. Because of the reduction in the nanosize of CaCO₃, drastic improvements in the mechanical properties were found. The size of 9 nm showed the highest increase in the tensile strength (3.89 MPa) in comparison with commercial CaCO₃ and the two other sizes of nano‐CaCO₃ up to an 8 wt % loading in SBR. The elongation at break also increased up to 824% for the 9‐nm size in comparison with commercial CaCO₃ and the two other sizes of nano‐CaCO₃. Also, these results were compared with nano‐CaCO₃‐filled SBR without linseed oil as an extender. The modulus at 300% elongation, hardness, specific gravity, and flame‐retarding properties increased with a reduction in the nanosize with linseed oil as an extender, which helped with the uniform dispersion of nano‐CaCO₃ in the rubber matrix. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2563–2571, 2005     

Optimizing 3D printing performance of acrylonitrile‐butadiene‐styrene composites with cellulose nanocrystals/silica nanohybrids

The preparation of 3D printed products with excellent comprehensive performance is still receiving much attention. Cellulose, the most abundant and green natural polymer, was used in this study to fabricate polymeric composites used for 3D printing. Specifically, novel cellulose nanocrystals/silica nanohybrids (CSNs) were synthesized via the sol–gel method using cellulose nanocrystals (CNCs) obtained by hydrolysis of sulfuric acid as raw materials, and the thermostability was significantly improved due to the adsorption of silica (SiO₂) on the surface of the CNCs via hydrogen bonding and covalent bonds. Subsequently, the CSNs were used in fused deposition modeling (FDM) with acrylonitrile‐butadiene‐styrene (ABS) as the matrix. Unlike ABS/CNC product which shows obvious yellowing, the ABS/CSN product shows a smooth undefiled surface, demonstrating their excellent applicability to high temperature FDM molding. Further, the effect of different silane coupling agents on the mechanical properties was compared and organically modified CSNs (oCSNs) were prepared using KH570 to optimize the dispersion of the filler and the interaction with the matrix. Satisfactorily, the addition of organically modified oCSNs not only does not degrade the fluidity but it also eliminates the warpage of FDM products and improves both layer adhesion and mechanical properties. This study provides a pioneering strategy for the thermal processing applications of CNCs and the modification of FDM products. © 2019 Society of Chemical Industry     

Effect of surface modifiers and surface modification methods on properties of acrylonitrile–butadiene–styrene/poly(methyl methacrylate)/nano‐calcium carbonate composites

Nano‐calcium carbonate (nano‐CaCO₃) was used in this article to fill acrylonitrile–butadiene–styrene (ABS)/poly(methyl methacrylate) (PMMA), which is often used in rapid heat cycle molding process (RHCM). To achieve better adhesion between nano‐CaCO₃ and ABS/PMMA, nano‐CaCO₃ particles were modified by using titanate coupling agent, aluminum–titanium compound coupling agent, and stearic acid. Dry and solution methods were both utilized in the surface modification process. ABS/PMMA/nano‐CaCO₃ composites were prepared in a corotating twin screw extruder. Influence of surface modifiers and surface modification methods on mechanical and flow properties of composites was analyzed. The results showed that collaborative use of aluminum–titanium compound coupling agent and stearic acid for nano‐CaCO₃ surface modification is optimal in ABS/PMMA/nano‐CaCO₃ composites. Coupling agent can increase the melt flow index (MFI) and tensile yield strength of ABS/PMMA/nano‐CaCO₃ composites. The Izod impact strength of composites increases with the addition of titanate coupling agent up to 1 wt %, thereafter the Izod impact strength shows a decrease. The interfacial adhesion between nano‐CaCO₃ and ABS/PMMA is stronger by using solution method. But the dispersion uniformity of nano‐CaCO₃ modified by solution method is worse. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Investigation on preparation and property of nano‐CaCO3/PP masterbatch modified by reactive monomers

Nano‐CaCO₃/polypropylene (PP) masterbatch containing above 80 wt % nano‐CaCO₃ was prepared by nano‐CaCO₃ coated PP modified by reactive monomers. The chemical interaction, crystallization and melting behavior, thermal stability, morphology, and surface contact angle of masterbatch were investigated with IR, DSC, TEM, TGA, ESCA, and surface contact angle. The results indicated that nano‐CaCO₃ was coated by PP graft copolymers in the masterbatch modified by reactive monomers. The graft ratio and crystallization and melting behavior of PP in the masterbatch depended on the type and content of reactive monomer. The crystallization temperatures of masterbatch modified by reactive monomer is methyl methacrylate > butyl acrylate > methyl acrylate ≈ mixture of acrylic acid and styrene > unmodified ≈ maleic anhydride ≈ acrylic acid > styrene. Modification by reactive monomer increased the thermal stability and surface contact angle of masterbatch. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3907–3914, 2006     

Synergistic effect of ammonium polyphosphate and expandable graphite on flame‐retardant properties of acrylonitrile‐butadiene‐styrene

A new intumescent flame‐retardant (IFR) system consisting of expandable graphite (EG) and ammonium polyphosphate (APP) was applied in acrylonitrile–butadiene–styrene (ABS) resin. A synergistic effect between EG and APP on the flame retardancy of ABS was observed. Fixing the total loading of flame retardant at 15 wt %, the limited oxygen index (LOI) could reach 31 vol % at a weight ratio of 3 : 1 for EG and APP. While LOI values of EG‐ and APP‐filled ABS were only 26.0 and 21.5 vol % at the same loading, respectively. The UL‐94 vertical burning test suggested that samples with different ratios of EG and APP could all pass V‐0 rating while the samples containing EG and APP alone only passed V‐1 rating. Thermogravimetric analysis indicated that the addition of EG and APP (3 : 1 by weight) to ABS led to an increase in the amount of high‐temperature residue by 11.8 wt %, and a decrease of mass loss rate by 0.7%/°C compared with pure ABS. Scanning electronic microscopy revealed a homogeneous compact intumescent char layer of ABS/EG/APP samples. Based on our experiment and combined with others' previous studies, the synergistic mechanism is inferred. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Magnetite‐functionalized graphene/poly(styrene‐butadiene‐styrene) composites: thermal and mechanical properties

Advanced polymer composites containing organic–inorganic fillers are gaining increasing attention due to their multifunctional applications. In this work, poly(styrene‐butadiene‐styrene) (SBS) composites containing magnetite‐functionalized graphene (FG) were prepared by a dissolution ? dispersion ? precipitation solution method. Evidently, through morphology studies, amounts of FG were well distributed in the SBS matrix. Improvements in neat SBS properties with respect to FG loading in terms of thermal stability, creep recovery and mechanical properties are presented. As expected, the addition of FG improved the thermal stability and mechanical properties of the composites. The yield strength and Young's modulus of the SBS increased by 66% and 146% at 5 wt% filler loading which can be attributed to the reinforcing nature of FG. Similarly, an increase in the storage and loss modulus of the composites showed a reinforcement effect of the filler even at low concentration. The results also showed the significant role of FG in improving the creep and recovery performance of the SBS copolymer. Creep deformation decreased with filler loading but increased with temperature. © 2017 Society of Chemical Industry     

Improved mechanical properties and structure of PP/nano‐CaCO3 blends prepared by low‐frequency vibration injection molding

BACKGROUD: Melt vibration technology was used to prepare injection samples of polypropylene (PP)/nano‐CaCO₃ blends. It is well known that nano‐CaCO₃ particles are easy to agglomerate owing to their large surface energy. Improving the distribution of nano‐CaCO₃ particles in PP/nano‐CaCO₃ blends is very important for enhancing the mechanical properties. In this work, low‐frequency vibration was imposed on the process of injection molding of PP/nano‐CaCO₃ blends. The aim of importing a vibration field was to change the crystal structure of PP as we studied previously and improve the distribution of nano‐CaCO₃ particles. Furthermore, the mechanical properties were improved. RESULTS: Through melt vibration, the mechanical properties of PP/nano‐CaCO₃ samples were improved significantly. Compared with conventional injection molding, the enhancement of the tensile strength and impact strength of the samples molded by vibration injection molding was 17.68 and 175.96%, respectively. According to scanning electron microscopy, wide‐angle X‐ray diffraction and differential scanning calorimetry measurements, it was found that a much better dispersion of nano‐CaCO₃ in samples was achieved by vibration injection molding. Moreover, the crystal structure of PP in PP/CaCO₃ vibration samples changed. The γ crystal form was achieved at the shear layer of vibration samples. Moreover, the degree of crystallinity of PP in vibration samples increased 6% compared with conventional samples. CONCLUSION: Concerning the microstructure, melt vibration could effectively change the crystal structure and increase the degree of crystallinity of PP besides improving the distribution of nano‐CaCO₃ particles. Concerning the macrostructure, melt vibration could enhance the mechanical properties. The improvement of mechanical properties of PP/nano‐CaCO₃ blends prepared by low‐frequency vibration injection molding should be attributed to the even distribution of nano‐CaCO₃ particles and the formation of γ‐PP and the increase of the degree of cystallinity. Copyright © 2007 Society of Chemical Industry     

Application of a novel halogen‐free intumescent flame retardant for acrylonitrile‐butadiene‐styrene

A novel intumescent flame retardant (IFR), containing ammonium polyphosphate (APP) and poly(tetramethylene terephthalamide) (PA4T), was prepared to flame‐retard acrylonitrile‐butadiene‐styrene (ABS). The flame retardation of the IFR/ABS composite was characterized by limiting oxygen index (LOI) and UL‐94 test. Thermogravimetric analysis (TGA) and TGA coupled with Fourier transform infrared spectroscopy (TG‐FTIR) were carried out to study the thermal degradation behavior of the composite and look for the mechanism of the flame‐retarded action. The morphology of the char obtained after combustion of the composite was studied by scanning electron microscopy (SEM). It has been found the intumescent flame retardant showed good flame retardancy, with the LOI value of the PA4T/APP/ABS (7.5/22.5/70) system increasing from 18.5 to 30% and passing UL‐94 V‐1 rating. Meanwhile, the TGA and TG‐FTIR work indicated that PA4T could be effective as a carbonization agent and there was some reaction between PA4T and APP, leading to some crosslinked and high temperature stable material formed, which probably effectively promoted the flame retardancy of ABS. Moreover, it was revealed that uniform and compact intumescent char layer was formed after combustion of the intumescent flame‐retarded ABS composite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Study of viscoelastic properties of nanocomposites of SiO2–acrylonitrile–butadiene–styrene

Nanocomposites of acrylonitrile–butadiene–styrene (ABS) and nanosilica with different nanoparticle sizes and various loadings are prepared. Rheological experiments such as frequency sweep, strain sweep, and rotational test are performed to investigate the influence of nanoparticle loading and size on the viscoelastic properties of the nanocomposites. The results show that nanocomposites with higher filler loading and smaller particle size have both higher storage and loss moduli. Moreover, the results indicate that the storage modulus is more sensitive than loss modulus to filler loading and nanoparticle size. The smaller nanoparticles and higher filler loadings lead to the enhancement of nanoparticle surface area so that the viscoelastic properties are intensified through increase of polymer chain adsorption on nanoparticle, and creation of a network structure in the nanocomposites. The network structure causes changes to the rheological behavior of the nanocomposite such as solid‐like behavior in the low‐frequency region and reduction of the Newtonian region. The scanning electron microscopy micrographs revealed that the particle aggregates increase with particle size reduction and increasing nanoparticle content. We also used a nonlinear optimization to obtain the parameters of a multimode Maxwell model for low nanofiller content ABS/SiO₂ nanocomposites and found the relaxation times of the polymer chains increased with increasing nanoparticle content. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of compatibilizer in acrylonitrile‐butadiene‐styrene toughened nylon 6 blends: Ductile–brittle transition temperature

The ductile–brittle transition temperatures were determined for compatibilized nylon 6/acrylonitrile‐butadiene‐styrene (PA6/ABS) copolymer blends. The compatibilizers used for those blends were methyl methacrylate‐co‐maleic anhydride (MMA‐MAH) and MMA‐co‐glycidyl methacrylate (MMA‐GMA). The ductile–brittle transition temperatures were found to be lower for blends compatibilized through maleate modified acrylic polymers. At room temperature, the PA6/ABS binary blend was essentially brittle whereas the ternary blends with MMA‐MAH compatibilizer were supertough and showed a ductile–brittle transition temperature at ?10°C. The blends compatibilized with maleated copolymer exhibited impact strengths of up to 800 J/m. However, the blends compatibilized with MMA‐GMA showed poor toughness at room temperature and failed in a brittle manner at subambient temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2643–2647, 2003     

Preparation,characterization, and properties of crosslinked hydroxylated poly(styrene‐b‐butadiene‐b‐styrene) triblock copolymer

Acrylic acid was crosslinked with N,N′‐methylenebisacrylamide and converted to bioactive hydrogels by neutralization with different amino containing compounds. Several amino containing compounds were used such as 2‐aminopyridine, triethanol amine, hexamethylenetetramine (HMTA), pyridine, and imidazole. The best crosslinker ratio was determined in addition to the maximum absorbed water in different mediums. The antibacterial activity of the prepared gels were examined against examples of Gram‐positive (Staphylococcus aureus) and Gram‐negative bacteria (Escherichia coli) using agar plate method. The study was extended by evaluating one of prepared gels in columns as models for water filters. All prepared gels showed antibacterial action in agar plate method against both bacterium and the column method using one of the prepared gels showed excellent filtration and biocidal action. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of poly(ether‐ester‐amide)/poly(acrylonitrile‐co‐butadiene‐co‐styrene) antistatic blends

A novel antistatic agent poly(ether‐ester‐amide) (PEEA) based on caprolactam, polyethylene glycol, and 6‐aminocaproic acid was successfully synthesized by melting polycondensation. The structure, thermal properties, and antistatic ability of the copolymer were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analyses, and ZC36 megohmmeter. Test results show that PEEA is a block copolymer with a melting point of 217°C and a thermal decomposition temperature of 409°C, together with a surface resistivity of 10⁸ Ω/sq. Antistatic poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) materials were prepared by blending different content of PEEA to ABS resin. The antistatic performances, morphology, and mechanical properties were investigated. It is indicated that the surface resistivity of PEEA/ABS blends decrease with the increasing PEEA content, and the excellent antistatic performance is obtained when the antistatic agent is up to 10–15%. The antistatic performance is hardly influenced by water‐washing and relative humidity, and a permanent antistatic performance is available. The antistatic mechanism is investigated. The compatibility of the blends was studied by scanning electron microscopy images. The ladder distribution of antistatic agent is formed, and a rich phase of antistatic agent can be found in the surface layer. The elongations at break of the blend are improved with the increasing antistatic agent; the tensile strength and the notched impact strength kept almost the same. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Application of styrene‐acrylonitrile random copolymer–polyarylate block copolymer as reactive compatibilizer for polyamide and acrylonitrile‐butadiene‐styrene blends

Styrene‐acrylonitrile random copolymer (SAN) and polyarylate (PAr) block copolymer were applied as a reactive compatibilizer for polyamide‐6 (PA‐6)/acrylonitrile‐butadiene‐styrene (ABS) copolymer blends. The SAN–PAr block copolymer was found to be effective for compatibilization of PA‐6/ABS blends. With the addition of 3.0–5.0 wt % SAN–PAr block copolymer, the ABS‐rich phase could be reduced to a smaller size than 1.0 μm in the 70/30 and 50/50 PA‐6/ABS blends, although it was several microns in the uncompatibilized blends. As a result, for the blends compatibilized with 3–5 wt % block copolymer the impact energy absorption reached the super toughness region in the 70/30 and 50/50 PA‐6/ABS compositions. The compatibilization mechanism of PA‐6/ABS by the SAN–PAr block copolymer was investigated by tetrahydrofuran extraction of the SAN–PAr block copolymer/PA‐6 blends and the model reactions between the block copolymer and low molecular weight compounds. The results of these experiments indicated that the SAN–PAr block copolymer reacted with the PA‐6 during the melt mixing process via an in situ transreaction between the ester units in the PAr chain and the terminal amine in the PA‐6. As a result, SAN–PAr/PA‐6 block copolymers were generated during the melt mixing process. The SAN–PAr block copolymer was supposed to compatibilize the PA‐6 and ABS blend by anchoring the PAr/PA‐6 and SAN chains to the PA‐6 and ABS phases, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2300–2313, 2002     

Synergistic effect of a novel charring agent with ammonium polyphosphate on flame retardancy and thermal degradation of acrylonitrile‐butadiene‐styrene copolymer

A novel charring agent poly(1,3‐propylene terephthalamide) (PPTA) was synthesized and characterized by Fourier transform infrared spectroscopy and ¹H nuclear magnetic resonance. This novel charring agent combined with ammonium polyphosphate (APP) was adopted as an intumescent flame retardant (IFR) to impart flame retardance and dripping resistance to acrylonitrile‐butadiene‐styrene copolymer (ABS). Flammability and thermal behaviors of the treated ABS were investigated by limiting oxygen index, vertical burning test and thermogravimetric analysis. The results showed that the IFR with the novel charring agent had both excellent flame retardant and anti‐dripping abilities for ABS. The thermogravimetric analysis curves indicated that there was a synergistic effect between PPTA and APP, which greatly promoted the char formation of IFR‐ABS composites. Meanwhile, the thermal degradation mechanism of PPTA and APP/PPTA was characterized using thermogravimetric analysis/infrared spectrometry. The results demonstrated that APP changed the thermal degradation behavior of PPTA and reacted with PPTA to form a crosslinked structure. Additionally, the structure and morphology of char residues were studied by Fourier transform infrared spectroscopy and scanning electron microscopy. Copyright © 2011 Society of Chemical Industry     

Preparation and properties of TiO2‐filled poly(acrylonitrile‐butadiene‐styrene)/epoxy hybrid composites

Poly (acrylonitrile‐butadiene‐styrene) (ABS) was used to modify diglycidyl ether of bisphenol‐A type of epoxy resin, and the modified epoxy resin was used as the matrix for making TiO₂ reinforced nanocomposites and were cured with diaminodiphenyl sulfone for superior mechanical and thermal properties. The hybrid nanocomposites were characterized by using thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), universal testing machine (UTM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The bulk morphology was carefully analyzed by SEM and TEM and was supported by other techniques. DMA studies revealed that the DDS‐cured epoxy/ABS/TiO₂ hybrid composites systems have two T_gs corresponding to epoxy and ABS rich phases and have better load bearing capacity with the addition of TiO₂ particles. The addition of TiO₂ induces a significant increase in tensile properties, impact strength, and fracture toughness with respect to neat blend matrix. Tensile toughness reveals a twofold increase with the addition of 0.7 wt % TiO₂ filler in the blend matrix with respect to neat blend. SEM micrographs of fractured surfaces establish a synergetic effect of both ABS and TiO₂ components in the epoxy matrix. The phenomenon such us cavitation, crack path deflection, crack pinning, ductile tearing of the thermoplastic, and local plastic deformation of the matrix with some minor agglomerates of TiO₂ are observed. However, between these agglomerates, the particles are separated well and are distributed homogeneously within the polymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of injection‐homo‐polypropylene filled with nano‐CaCO3

Nano‐CaCO₃/homo‐PP composites were prepared by melt‐blending using twin‐screw extruder. The results show that not only the impact property but also the bending modulus of the system have been evidently increased by adding nano‐CaCO₃. The nano‐CaCO₃ particles have been dispersed in the matrix in the nanometer scale which was investigated by means of transmission electron microscopy (TEM). The toughening mechanism of nano‐CaCO₃, investigated by means of dynamical mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM), lies on that the nano‐CaCO₃ particles take an action of initiating and terminating crazing (silver streak), which can absorb more impact energy than the neat PP. At the same time, the nano‐CaCO₃ particles, as the nuclear, decrease the crystal size of PP, the results of which were investigated by means of polarized optical microscope (POM). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010