Effect of Sb Doping on the Thermoelectric Properties of Mg<Subscript>2</Subscript>Si<Subscript>0.7</Subscript>Sn<Subscript>0.3</Subscript> Solid Solutions

This study focuses on Sb-doped Mg₂(Si,Sn) thermoelectric material. Samples were successfully fabricated using a hybrid synthesis method consisting of three different processes: induction melting, solid-state reaction, and a hot-press sintering technique. We found that the carrier concentration increased with Sb content, while the Seebeck coefficient exhibited a decreasing trend. Sb doping was shown to improve the power factor and thermoelectric figure of merit compared with the undoped material, yielding a peak figure of merit (ZT) of ~0.55 at 620 K, while leaving the band gap of Mg₂Si_0.7Sn_0.3 almost unchanged.     

First-Principles and Experimental Studies of Y-Doped Mg<Subscript>2</Subscript>Si Prepared Using Field-Activated Pressure-Assisted Synthesis

The thermoelectric properties of Y-doped (1000 ppm, 2000 ppm, 3000 ppm) Mg₂Si fabricated using field-activated pressure-assisted synthesis (FAPAS) have been characterized using measurements of electrical resistivity (ρ), Seebeck coefficient (S), and thermal conductivity (κ) at temperatures ranging from 285 K to 810 K. The Y-doped Mg₂Si samples were n-type in the measured temperature range. A first-principles calculation revealed that the Y atoms were expected to be primarily located at Mg sites. In sample doped with 2000 ppm Y, which exhibited the best electrical and thermal conductivity, the absolute value of the Seebeck coefficient increased in the temperature range of 320 K to 680 K, being higher than that of undoped Mg₂Si. Moreover, this sample exhibited a higher level of electrical conductivity and a higher power factor. In addition, introduction of Y decreased the thermal conductivity appreciably, indicating that Y dopants are favorable for improving the properties of Mg₂Si.     

Solid-State Synthesis of Te-Doped Mg<Subscript>2</Subscript>Si

Te-doped Mg₂Si (Mg₂Si:Te _m , m = 0, 0.01, 0.02, 0.03, 0.05) alloys were synthesized by a solid-state reaction and mechanical alloying. The electronic transport properties (Hall coefficient, carrier concentration, and mobility) and thermoelectric properties (Seebeck coefficient, electrical conductivity, thermal conductivity, and figure of merit) were examined. Mg₂Si was synthesized successfully by a solid-state reaction at 673 K for 6 h, and Te-doped Mg₂Si powders were obtained by mechanical alloying for 24 h. The alloys were fully consolidated by hot-pressing at 1073 K for 1 h. All the Mg₂Si:Te _m samples showed n-type conduction, indicating that the electrical conduction is due mainly to electrons. The electrical conductivity increased and the absolute value of the Seebeck coefficient decreased with increasing Te content, because Te doping increased the electron concentration considerably from 10¹⁶ cm⁻³ to 10¹⁸ cm⁻³. The thermal conductivity did not change significantly on Te doping, due to the much larger contribution of lattice thermal conductivity over the electronic thermal conductivity. Thermal conduction in Te-doped Mg₂Si was due primarily to lattice vibrations (phonons). The thermoelectric figure of merit of intrinsic Mg₂Si was improved by Te doping.     

Bulk Nanostructured Thermoelectric Materials: Preparation,Structure and Properties

Bulk nanostructured materials have recently emerged as a new paradigm for improving the performance of existing thermoelectric materials. Here, we fabricated two kinds of bulk nanostructured thermoelectric materials by a bottom-up strategy and an in situ precipitation method, respectively. Binary PbTe was fabricated by a combination of chemical synthesis and hot pressing. The grain sizes of the hot pressed bulk samples varied from 200 nm to 400 nm, which significantly contributed to the reduction of thermal conductivity due to the enhanced boundary phonon scattering. The highest figure of merit ZT of the binary PbTe sample reached 0.8 at 580 K. Mg₂(Si,Sn) solid solutions have shown great promise for thermoelectric application, due to good thermoelectric properties, non-toxicity, and abundantly available constituent elements. The nanoscale microstructure observation of the compounds showed the existence of nanophases formed in situ, which is believed to be related to the relatively low lattice thermal conductivity in this material system. The highest ZT of Sb-doped Mg₂(Si,Sn) samples reached 1.1 at 770 K.     

Thermoelectric Behavior of Sb- and Al-Doped <Emphasis Type="Italic">n</Emphasis>-Type Mg<Subscript>2</Subscript>Si Device Under Large Temperature Differences

The thermoelectric (TE) characteristics of Sb- and Al-doped n-type Mg₂Si elemental devices fabricated using material produced from molten commercial doped polycrystalline Mg₂Si were examined. The TE devices were prepared using a plasma-activated sintering (PAS) technique. To complete the devices, Ni electrodes were fabricated on each end of them during the sintering process. To realize durable devices for large temperature differences, thermodynamically stable Sb-doped Mg₂Si (Sb-Mg₂Si) was exposed to the higher temperature and Al-doped Mg₂Si (Al-Mg₂Si) was exposed to the cooler temperature. The devices consisted of segments of Sb-Mg₂Si and Al-Mg₂Si with sizes in the following ratios: Sb-Mg₂Si:Al-Mg₂Si = 4:1, 1:1, and 1:4. A device specimen composed solely of Sb-Mg₂Si showed no notable deterioration even after aging for 1000 h, while some segmented specimens, such as those with Sb-Mg₂Si:Al-Mg₂Si = 1:1 and 1:4, suffered from a considerable drop in output current over the large ΔT range. The observed power generated by specimens with Sb-Mg₂Si:Al-Mg₂Si = 1:1 and 1:4 and sizes of 2 mm × 2 mm × 10 mm were 50.7 mW and 49.5 mW, respectively, with higher and lower temperatures of 873 K and 373 K, respectively. For the sample composed solely of Sb-Mg₂Si, a power of 55 mW was demonstrated. An aging test for up to 1000 h for the same ΔT range indicated drops in output power of between ∼3% and 20%.     

Crystal Structure and High-Temperature Thermoelectric Properties of the Mo<Subscript>3−<Emphasis Type="Italic">x</Emphasis></Subscript>Ru<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Sb<Subscript>7</Subscript> Compounds

Zintl phases are currently receiving great attention for their thermoelectric potential typified by the discovery of a high ZT value in Yb₁₄MnSb₁₁-based compounds. Herein, we report on the crystallographic characterization via neutron and x-ray diffraction experiments, and on the thermoelectric properties measured in the 300 K to 1000 K temperature range, of Mo₃Sb₇ and its isostructural compounds Mo_3−x Ru _x Sb₇. Even though Mo₃Sb₇ displays rather high ZT values given its metallic character, the partial substitution of Mo by Ru substantially improves its thermoelectric properties, resulting in a ZT value of ∼0.45 at 1000 K for x = 0.8.     

Low-Temperature Thermoelectric Properties of Co<Subscript>0.9</Subscript>Fe<Subscript>0.1</Subscript>Sb<Subscript>3</Subscript>-Based Skutterudite Nanocomposites with FeSb<Subscript>2</Subscript> Nanoinclusions

Bulk thermoelectric nanocomposite materials have great potential to exhibit higher ZT due to effects arising from their nanostructure. Herein, we report low-temperature thermoelectric properties of Co_0.9Fe_0.1Sb₃-based skutterudite nanocomposites containing FeSb₂ nanoinclusions. These nanocomposites can be easily synthesized by melting and rapid water quenching. The nanoscale FeSb₂ precipitates are well dispersed in the skutterudite matrix and reduce the lattice thermal conductivity due to additional phonon scattering from nanoscopic interfaces. Moreover, the nanocomposite samples also exhibit enhanced Seebeck coefficients relative to regular iron-substituted skutterudite samples. As a result, our best nanocomposite sample boasts a ZT = 0.041 at 300 K, which is nearly three times as large as that for Co_0.9Fe_0.1Sb₃ previously reported.     

Preparation and Thermoelectric Properties of LaGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> and SmGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript>

Thermoelectric materials are attractive since they can recover waste heat directly in the form of electricity. In this study, the thermoelectric properties of ternary rare-earth sulfides LaGd_1+x S₃ (x = 0.00 to 0.03) and SmGd_1+x S₃ (x = 0.00 to 0.06) were investigated over the temperature range of 300 K to 953 K. These sulfides were prepared by CS₂ sulfurization, and samples were consolidated by pressure-assisted sintering to obtain dense compacts. The sintered compacts of LaGd_1+x S₃ were n-type metal-like conductors with a thermal conductivity of less than 1.7 W K⁻¹ m⁻¹. Their thermoelectric figure of merit ZT was improved by tuning the chemical composition (self-doping). The optimized ZT value of 0.4 was obtained in LaGd_1.02S₃ at 953 K. The sintered compacts of SmGd_1+x S₃ were n-type hopping conductors with a thermal conductivity of less than 0.8 W K⁻¹ m⁻¹. Their ZT value increased significantly with temperature. In SmGd_1+x S₃, the ZT value of 0.3 was attained at 953 K.     

Thermoelectric Properties of Sb-Doped Mg<Subscript>2</Subscript>Si<Subscript>0.3</Subscript>Sn<Subscript>0.7</Subscript>

Mg₂(Si_0.3Sn_0.7)_1−y Sb _y (0 ≤ y ≤ 0.04) solid solutions were prepared by a two-step solid-state reaction method combined with the spark plasma sintering technique. Investigations indicate that the Sb doping amount has a significant impact on the thermoelectric properties of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y compounds. As the Sb fraction y increases, the electron concentration and electrical conductivity of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y first increase and then decrease, and both reach their highest value at y = 0.025. The sample with y = 0.025, possessing the highest electrical conductivity and one of the higher Seebeck coefficient values among all the samples, has the highest power factor, being 3.45 mW m⁻¹ K⁻² to 3.69 mW m⁻¹ K⁻² in the temperature range of 300 K to 660 K. Meanwhile, Sb doping can significantly reduce the lattice thermal conductivity (κ _ph) of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y due to increased point defect scattering, and κ _ph for Sb-doped samples is 10% to 20% lower than that of the nondoped sample for 300 K < T < 400 K. Mg₂(Si_0.3Sn_0.7)_0.975Sb_0.025 possesses the highest power factor and one of the lower κ _ph values among all the samples, and reaches the highest ZT value: 1.0 at 640 K.     

Thermoelectric Properties of <Emphasis Type="Italic">p</Emphasis>-Type Mg<Subscript>2.00</Subscript>Si<Subscript>0.25</Subscript>Sn<Subscript>0.75</Subscript> with Li and Ag Double Doping

Mg₂Si_1−x Sn _x -system solid solutions are ecofriendly semiconductors that are promising materials for thermoelectric generators in the middle temperature range. To produce a thermoelectric device, high-performance p- and n-type materials must be balanced. In this paper, p-type Mg_2.00Si_0.25Sn_0.75 with Li and Ag double doping was prepared by the liquid–solid reaction method and hot-pressing. Effects of Li and Ag double doping on thermoelectric properties were investigated in the temperature range from room temperature to 850 K. All sintered compacts were identified as single-phase solid solutions with anti-fluorite structure. The carrier concentration increased with the double doping. The temperature dependence of resistivity of the double-doped samples was similar to that of a metal. The seebeck coefficient increased with temperature to a maximum value and then decreased in the intrinsic region. Thermal conductivity decreased linearly with increasing temperature, reaching a minimum near the intrinsic region, and then increased rapidly because of the contribution of the bipolar component. The dimensionless figure of merit reached 0.32 at 610 K for Mg_2.00Si_0.25Sn_0.75 double-doped with Li-5000 ppm and Ag-20000 ppm.     

High-Performance (Ag<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>SbTe<Subscript><Emphasis Type="Italic">x</Emphasis>/2+1.5</Subscript>)<Subscript>15</Subscript>(GeTe)<Subscript>85</Subscript> Thermoelectric Materials Prepared by Melt Spinning

A new preparation process combining melt spinning and hot pressing has been developed for the (Ag _x SbTe _x/2+1.5)₁₅(GeTe)₈₅ (TAGS-85) system. Compared with samples prepared by the traditional air-quenching and hot-pressing method, electrical conductivity and thermal conductivity are lowered. The thermoelectric performance of the TAGS-85 samples varied with changing Ag content and reached the highest ZT of 1.48 when x was 0.8 for the melt-spun sample, compared with the maximum ZT of 1.36 for the air-quenched sample. The Seebeck coefficient of the melt-spun TAGS-85 alloys was improved, while both the electrical conductivity and thermal conductivity were decreased. The net result of this process is to effectively enlarge the temperature span of ZT > 1, which will benefit industrial application.     

Synthesis and Characterization of Al-Doped Mg2Si Thermoelectric Materials

Magnesium silicide (Mg₂Si)-based alloys are promising candidates for thermoelectric (TE) energy conversion for the middle to high range of temperature. These materials are very attractive for TE research because of the abundance of their constituent elements in the Earth’s crust. Mg₂Si could replace lead-based TE materials, due to its low cost, nontoxicity, and low density. In this work, the role of aluminum doping (Mg₂Si:Al = 1:x for x = 0.005, 0.01, 0.02, and 0.04 molar ratio) in dense Mg₂Si materials was investigated. The synthesis process was performed by planetary milling under inert atmosphere starting from commercial Mg₂Si pieces and Al powder. After ball milling, the samples were sintered by means of spark plasma sintering to density >95%. The morphology, composition, and crystal structure of the samples were characterized by field-emission scanning electron microscopy, energy-dispersive spectroscopy, and x-ray diffraction analyses. Moreover, Seebeck coefficient analyses, as well as electrical and thermal conductivity measurements were performed for all samples up to 600°C. The resultant estimated ZT values are comparable to those reported in the literature for these materials. In particular, the maximum ZT achieved was 0.50 for the x = 0.01 Al-doped sample at 600°C.     

Effect of Electric Current on the Performance of Bi<Subscript>1.2</Subscript>Sb<Subscript>4.8</Subscript>Te<Subscript>9</Subscript> Thermoelectric Material Prepared by a Field-Activated Pressure-Assisted Sintering Process

Field-activated pressure-assisted sintering (FAPAS) was applied to sinter Bi_1.2Sb_4.8Te₉ thermoelectric materials under different conditions, including no-current sintering (NCS), low-density current sintering (LCS), and high-density current sintering (HCS). The effect of the current density on the final thermoelectric performance of the products was investigated. Applying a higher-density electric current and shorter dwell time can improve the thermoelectric performance of the sample by increasing its electric conductivity and decreasing its thermal conductivity. The maximum figure of merit ZT values of the NCS, LCS, and HCS samples were 0.46, 0.48, and 0.57, respectively. Therefore, applying a high-density electric current in the sintering process may be an effective way to obtain Bi_1.2Sb_4.8Te₉ thermoelectric material with high ZT value.     

Synthesis and Thermoelectric Properties of the Double-Filled Skutterudite Yb<Subscript>0.2</Subscript>In<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>Co<Subscript>4</Subscript>Sb<Subscript>12</Subscript>

Filled skutterudites have long been singled out as one of the prime examples of phonon glass electron crystal materials. Recently the double-filling approach in these materials has been attracting increased attention. In this study, Yb_0.2In _y Co₄Sb₁₂ (y = 0.0 to 0.2) samples have been prepared by a simple melting method and their thermoelectric properties have been investigated. The power factor is increased dramatically when increasing the In content, while the lattice thermal conductivity is lowered considerably, leading to a large increase of the ZT value. A state-of-the-art ZT value of 1.0 is attained in Yb_0.2In_0.2Co₄Sb₁₂ at 750 K.     

Doping Effects on the Thermoelectric Properties of AgSbTe<Subscript>2</Subscript>

A doping study of ternary alloys AgSbTe₂ doped with excess AgTe, NaTe, NaSe, TlTe, BiTe, and excess Pb showed that carrier concentrations can be effectively manipulated. Measured thermopower and resistivity indicate a shift of the power factor peak toward the lower-temperature regime. The measured figure of merit ZT increases from 0.5 to 1.2 after doping with NaSe, and 1.05 with TlTe, at 400 K. We also show that doping with Bi and Pb has a negative effect on the thermoelectric properties of these alloys.     

Thermoelectric Properties of Zintl Compound YbZn<Subscript>2</Subscript>Sb<Subscript>2</Subscript> with Mn Substitution in Anionic Framework

The thermoelectric properties of the Zintl compound YbZn₂Sb₂ with isoelectronic substitution of Zn by Mn in the anionic (Zn₂Sb₂)²⁻ framework have been studied. The p-type YbZn_2−x Mn _x Sb₂ (0.0 ≤ x ≤ 0.4) samples were prepared via melting followed by annealing and hot-pressing. Thermoelectric property measurement showed that the Mn substitution effectively lowered the thermal conductivity for all the samples, while it significantly increased the Seebeck coefficient for x < 0.2. As a result, a dimensionless figure of merit ZT of approximately 0.61 to 0.65 was attained at 726 K for x = 0.05 to 0.15, compared with the ZT of ~0.48 in the unsubstituted YbZn₂Sb₂.     

Thermoelectric Properties of Co<Subscript>4</Subscript>Sn<Subscript>6</Subscript>Se<Subscript>6</Subscript> Ternary Skutterudites

A ternary ordered variant of the skutterudite structure, the Co₄Sn₆Se₆ compound, was prepared. Polycrystalline samples were prepared by a modified ceramic method. The electrical conductivity, the Seebeck coefficient and the thermal conductivity were measured over a temperature range of 300–800 K. The undoped Co₄Sn₆Se₆ compound was of p-type electrical conductivity and had a band gap E _g of approximately 0.6 eV. The influence of transition metal (Ni and Ru) doping on the thermoelectric properties was studied. While the thermal conductivity was significantly lowered both for the undoped Co₄Sn₆Se₆ compound and for the doped compounds, as compared with the Co₄Sb₁₂ binary skutterudite, the calculated ZT values were improved only slightly.     

Synthesis and Characterization of <Emphasis Type="Italic">p</Emphasis>-Type Pb<Subscript>0.5</Subscript>Sn<Subscript>0.5</Subscript>Te Thermoelectric Power Generation Elements by Mechanical Alloying

A mechanical alloying (MA) process to transform elemental powders into solid Pb_0.5Sn_0.5Te with thermoelectric functionality comparable to melt-alloyed material is described. The room-temperature doping level and mobility as well as temperature-dependent electrical conductivity, Seebeck coefficient, and thermal conductivity are reported. Estimated values of lattice thermal conductivity (0.7 W m⁻¹ K⁻¹) are lower than some reports of functional melt-alloyed PbSnTe-based material, providing evidence that MA can engender the combination of properties resulting in highly functional thermoelectric material. Though doping level and Sn composition have not been optimized, this material exhibits a ZT value >0.5 at 550 K.     

Increase in the Thermoelectric Efficiency of the Disordered Phase of Layered Antiferromagnetic CuCrS<Subscript>2</Subscript>

The thermoelectric figure of merit (ZT) of the layered antiferromagnetic compound CuCrS₂ is further improved with increase in the Cr-vacancy disorder on sintering above 900°C. X-ray photoelectron spectroscopy and x-ray diffraction refinement results for different samples show that the chromium atoms are transferred from the filled layers to the vacant sites between the layers. This atomic disorder increases the electrical conductivity (σ) due to self-doping of the charge carriers and reduces thermal conductivity (κ) due to increase in phonon scattering. The Seebeck coefficient (S) is p-type and remains nearly temperature independent with values between 150 μV/K and 450 μV/K due to electronic doping in different samples.     

Low Thermal Conductivity and Enhanced Thermoelectric Performance in In and Lu Double-Filled CoSb<Subscript>3</Subscript> Skutterudites

The thermoelectric properties of indium (In) and lutetium (Lu) double-filled skutterudites In _x Lu _y Co₄Sb₁₂ prepared by high-pressure synthesis were investigated in detail from 4 K to 365 K. Our results indicate that In and Lu double filling can remarkably reduce the thermal conductivity, and substantially improve the thermoelectric performance. A thermoelectric figure of merit of ZT = 0.27 for In_0.13Lu_0.05Co_4.02Sb₁₂ was achieved at 365 K, being larger by one order of magnitude than that for CoSb₃. It is thought that the large difference in resonance frequencies of the In and Lu elements broadens the range of normal phonon scattering in the multifilled skutterudites, helping to achieve an even lower lattice thermal conductivity. This investigation suggests that an effective way to improve the thermoelectric performance of skutterudite materials is to use In and Lu double filling.