Lateral RESURF MOSFET fabricated on 4H-SiC(0001/sup ~/) C-face

Lateral reduced surface field (RESURF) metal-oxide-semiconductor field-effect transistors (MOSFETs) have been fabricated on 4H-SiC(0001/sup ~/) carbon face (C-face) substrates. The channel mobility of a lateral test MOSFET on a C-face was 41 cm/sup 2//V/spl middot/s, which was much higher than 5 cm/sup 2//V/spl middot/s for that on a Si-face. The specific on-resistance of the lateral RESURF MOSFET on a C-face was 79/spl Omega/ /spl middot/ cm/sup 2/, at a gate voltage of 25 V and drain voltage of 1 V. The breakdown voltage was 460 V, which was 79% of the designed breakdown voltage of 600 V. We measured the temperature dependence of R/sub on, sp/ for the RESURF MOSFET on the C-face. The R/sub on, sp/ increased with the increase in temperature.     

930-V 170-m/spl Omega//spl middot/cm/sup 2/ lateral two-zone RESURF MOSFETs in 4H-SiC with NO annealing

The first lateral two-zone reduced surface field MOSFETs in 4H-SiC with NO annealing are reported. Interface properties of 4H-SiC-SiO/sub 2/ are improved, with inversion layer field-effect mobility increased to 25 cm/sup 2//V/spl middot/s, five times higher than that of dry reoxidation process, and with channel resistance significantly reduced. Devices are normally off with low leakage current. Threshold voltage is around 3 V. Blocking voltage of 930 V and specific on-resistance of 170 m/spl Omega//spl middot/cm/sup 2/ were obtained. Large-area devices with multifinger geometry are also demonstrated with scaled-up current. The output characteristics exhibit excellent linear and saturation regions.     

Design and fabrication of RESURF MOSFETs on 4H-SiC(0001), (112~0), and 6H-SiC(0001)

Design and fabrication of lateral SiC reduced surface field (RESURF) MOSFETs have been investigated. The doping concentration (dose) of the RESURF and lightly doped drain regions has been optimized to reduce the electric field crowding at the drain edge or in the gate oxide by using device simulation. The optimum oxidation condition depends on the polytype: N/sub 2/O oxidation at 1300/spl deg/C seems to be suitable for 4H-SiC, and dry O/sub 2/ oxidation at 1250/spl deg/C for 6H-SiC. The average inversion-channel mobility is 22, 78, and 68 cm/sup 2//Vs for 4H-SiC(0001), (112~0), and 6H-SiC(0001) MOSFETs, respectively. RESURF MOSFETs have been fabricated on 10-/spl mu/m-thick p-type 4H-SiC(0001), (112~0), and 6H-SiC(0001) epilayers with an acceptor concentration of 1/spl times/10/sup 16/ cm/sup -3/. A 6H-SiC(0001) RESURF MOSFET with a 3-/spl mu/m channel length exhibits a high breakdown voltage of 1620 V and an on-resistance of 234 m/spl Omega//spl middot/cm/sup 2/. A 4H-SiC(112~0) RESURF MOSFET shows the characteristics of 1230 V-138 m/spl Omega//spl middot/cm/sup 2/.     

1677 V, 5.7 m/spl Omega//spl middot/cm/sup 2/ 4H-SiC BJTs

This letter reports the development of a high-performance power 4H-SiC bipolar junction transistor (BJT) with, simultaneously, a high blocking voltage and a low specific on-resistance (R/spl I.bar//sub ON/). A single BJT cell with an active area of 0.61 mm/sup 2/ achieves an open base collector-to-emitter blocking voltage (V/sub ceo/) of 1677 V and conducts up to 3.2 A at a forward voltage drop of V/sub CE/=3.0 V, corresponding to a low R/spl I.bar//sub ON/ of 5.7 m/spl Omega//spl middot/cm/sup 2/ up to Jc=525 A/cm/sup 2/ and a record high value of V/sub B//sup 2//R/sub SP/spl I.bar/ON/ of 493 MW/cm/sup 2/.     

A 4.15 kV 9.07-m/spl Omega//spl middot/cm/sup 2/ 4H-SiC Schottky-barrier diode using Mo contact annealed at high temperature

In this letter, we report the fabrication of high-voltage and low-loss 4H-SiC Schottky-barrier diodes (SBDs) with a performance close to the theoretical limit using a Mo contact annealed at high-temperature. High-temperature annealing for the Mo contact was found to be effective in controlling the Schottky-barrier height at 1.2-1.3 eV without degradation of n-factor and reverse characteristics. We successfully obtained a 1-mm/sup 2/ Mo-4H-SiC SBD with a breakdown voltage (V/sub b/) of 4.15 kV and a specific on resistance (R/sub on/) of 9.07 m/spl Omega//spl middot/cm/sup 2/, achieving a best V/sub b//sup 2//R/sub on/ value of 1898 MW/cm/sup 2/. We also obtained a 9-mm/sup 2/ Mo-4H-SiC SBD with V/sub b/ of 4.40 kV and R/sub on/ of 12.20 m/spl Omega//spl middot/cm/sup 2/.     

1300-V 6H-SiC lateral MOSFETs with two RESURF zones

A two-zone, lateral RESURF field 6H-SiC MOSFET with breakdown voltage as high as 1300 V and specific on-resistance of 160 m/spl Omega//spl middot/cm/sup 2/ has been fabricated. These MOSFETs exhibit stable and reversible breakdown indicating avalanche breakdown in SiC that has not been reported in earlier lateral SiC MOSFETs.     

Fully depleted dual-gated thin-film SOI P-MOSFETs fabricated in SOI islands with an isolated buried polysilicon backgate

P-channel dual-gated thin-film silicon-on-insulator (DG-TFSOI) MOSFETs have been fabricated with an isolated buried polysilicon backgate in an SOI island formed by epitaxial lateral overgrowth (ELO) of silicon. This structure allows individual operation of both the top and back gates rather than the conventional common backgate structure. When fully-depleted, the buried gate is used to individually shift the top gate threshold voltage (V/sub T/). A linear shift of /spl Delta/V/sub T,top///spl Delta/V/sub G,back/ of 0.5 V/V was achieved with a thin buried oxide. The effective density of interface traps (D/sub it/) for the backgate polysilicon-oxide SOI interface was measured to be 1.8/spl times/10/sup 11/ #/cm/sup 2//spl middot/eV as compared to the substrate-oxide of 1.1/spl times/10/sup 11/ #/cm/sup 2//spl middot/eV.     

4H-SiC power bipolar junction transistor with a very low specific ON-resistance of 2.9 m/spl Omega//spl middot/cm/sup 2/

This letter reports a newly achieved best result on the specific ON-resistance (R/sub SP/spl I.bar/ON/) of power 4H-SiC bipolar junction transistors (BJTs). A 4H-SiC BJT based on a 12-/spl mu/m drift layer shows a record-low specific-ON resistance of only 2.9 m/spl Omega//spl middot/cm/sup 2/, with an open-base collector-to-emitter blocking voltage (V/sub ceo/) of 757 V, and a current gain of 18.8. The active area of this 4H-SiC BJT is 0.61 mm/sup 2/, and it has a fully interdigitated design. This high-performance 4H-SiC BJT conducts up to 5.24 A at a forward voltage drop of V/sub CE/=2.5 V, corresponding to a low R/sub SP-ON/ of 2.9 m/spl Omega//spl middot/cm/sup 2/ up to J/sub c/=859 A/cm/sup 2/. This is the lowest specific ON-resistance ever reported for high-power 4H-SiC BJTs.     

Ge n-MOSFETs on lightly doped substrates with high-/spl kappa/ dielectric and TaN gate

In this letter, we report successful fabrication of germanium n-MOSFETs on lightly doped Ge substrates with a thin HfO/sub 2/ dielectric (equivalent oxide thickness /spl sim/10.8 /spl Aring/) and TaN gate electrode. The highest peak mobility (330 cm/sup 2//V/spl middot/s) and saturated drive current (130 /spl mu/A/sq at V/sub g/--V/sub t/=1.5 V) have been demonstrated for n-channel bulk Ge MOSFETs with an ultrathin dielectric. As compared to Si control devices, 2.5/spl times/ enhancement of peak mobility has been achieved. The poor performance of Ge n-MOSFET devices reported recently and its mechanism have been investigated. Impurity induced structural defects are believed to be responsible for the severe degradation.     

High-voltage normally off GaN MOSFETs on sapphire substrates

Gallium nitride self-aligned MOSFETs were fabricated using low-pressure chemical vapor-deposited silicon dioxide as the gate dielectric and polysilicon as the gate material. Silicon was implanted into an unintentionally doped GaN layer using the polysilicon gate to define the source and drain regions, with implant activation at 1100/spl deg/C for 5 min in nitrogen. The GaN MOSFETs have a low gate leakage current of less than 50 pA for circular devices with W/L=800/128 /spl mu/m. Devices are normally off with a threshold voltage of +2.7 V and a field-effect mobility of 45 cm/sup 2//Vs at room temperature. The minimum on-resistance measured is 1.9 m/spl Omega//spl middot/cm/sup 2/ with a gate voltage of 34 V (W/L=800/2 /spl mu/m). High-voltage lateral devices had a breakdown voltage of 700 V with gate-drain spacing of 9 /spl mu/m (80 V//spl mu/m), showing the feasibility of self-aligned GaN MOSFETs for high-voltage integrated circuits.     

Electrical characteristics of 8-/spl Aring/ EOT HfO/sub 2//TaN low thermal-budget n-channel FETs with solid-phase epitaxially regrown junctions

The authors demonstrate high-performing n-channel transistors with a HfO/sub 2//TaN gate stack and a low thermal-budget process using solid-phase epitaxial regrowth of the source and drain junctions. The thinnest devices have an equivalent oxide thickness (EOT) of 8 /spl Aring/, a leakage current of 1.5 A/cm/sup 2/ at V/sub G/=1 V, a peak mobility of 190 cm/sup 2//V/spl middot/s, and a drive-current of 815 /spl mu/A//spl mu/m at an off-state current of 0.1 /spl mu/A//spl mu/m for V/sub DD/=1.2 V. Identical gate stacks processed with a 1000-/spl deg/C spike anneal have a higher peak mobility at 275 cm/sup 2//V/spl middot/s, but a 5-/spl Aring/ higher EOT and a reduced drive current at 610 /spl mu/A//spl mu/m. The observed performance improvement for the low thermal-budget devices is shown to be mostly related to the lower EOT. The time-to-breakdown measurements indicate a maximum operating voltage of 1.6 V (1.2 V at 125 /spl deg/C) for a ten-year lifetime, whereas positive-bias temperature-instability measurements indicate a sufficient lifetime for operating voltages below 0.75 V.     

Novel FRESURF LDMOSFET devices with improved BV/sub dss/-R/sub dson/

In this letter, we propose and demonstrate a novel device based on a floating reduced surface field (FRESURF) concept which allows the realization of significantly higher breakdown voltage in a thin epitaxy-based power IC technology. The newly proposed device with the floating buried layer pulled back from the source side is able to realize an enhanced breakdown voltage (BV/sub dss/) without degrading the specific on-resistance (R/sub dson/A). BV/sub dss/-R/sub dson/A values like 47 V-0.28 m/spl Omega//spl middot/cm/sup 2/ or 93 V-0.82 m/spl Omega//spl middot/cm/sup 2/ have been realized with a conventional power IC technology without any added process complexity.     

GaAs MOSFET using InAlP native oxide as gate dielectric

GaAs metal-oxide-semiconductor field-effect transistors (MOSFETs) using wet thermally oxidized InAlP as the gate insulator are reported for the first time. Leakage current measurements show that the 11-nm-thick native oxide grown from an In/sub 0.49/Al/sub 0.51/P layer lattice-matched to GaAs has good insulating properties, with a measured leakage current density of 1.39/spl times/10/sup -7/ mA//spl mu/m/sup 2/ at 1 V bias. GaAs MOSFETs with InAlP native gate oxide have been fabricated with gate lengths from 7 to 2 /spl mu/m. Devices with 2-/spl mu/m-long gates exhibit a peak extrinsic transconductance of 24.2 mS/mm, an intrinsic transconductance of 63.8 mS/mm, a threshold voltage of 0.15 V, and an off-state gate-drain breakdown voltage of 21.2 V. Numerical Poisson's equation solutions provide close agreement with the measured sheet resistance and threshold voltage.     

Demonstration of 1789 V, 6.68 m/spl Omega/ /spl middot/ cm/sup 2/ 4H-SiC merged-PiN-Schottky diodes

The design, fabrication and characterisation of a high performance 4H-SiC diode of 1789 V-6.6 A with a low differential specific-on resistance (R/sub SP/spl I.bar/ON/) of 6.68 m/spl Omega/ /spl middot/ cm/sup 2/, based on a 10.3 /spl mu/m 4H-SiC blocking layer doped to 6.6/spl times/10/sup 15/ cm/sup -3/, is reported. The corresponding figure-of-merit of V/sub B//sup 2//R/sub SP/spl I.bar/ON/ for this diode is 479 MW/cm/sup 2/, which substantially surpasses previous records for all other MPS diodes.     

1710-V 2.77-m/spl Omega/cm/sup 2/ 4H-SiC trenched and implanted vertical junction field-effect transistors

This letter reports the demonstration of a 4H-SiC trenched and implanted vertical-junction field-effect transistor (TI-VJFET). The p/sup +/n junction gates are created on the sidewalls of deep trenches by angled Al implantation, which eliminates the need for epitaxial regrowth during the JFET fabrication. Blocking voltages up to 1710 V has been achieved with a voltage supporting drift layer of only 9.5 /spl mu/m by using a two-step junction termination extension. The TI-VJFET shows a low specific on-resistance R/sub ON-sp/ of 2.77m/spl Omega/cm/sup 2/, corresponding to a record high value of V/sub B//R/sub ON-sp/ equal to 1056 MW/cm/sup 2/.     

InGaAs/InP DHBTs with 120-nm collector having simultaneously high f/sub /spl tau//, f/sub max//spl ges/450 GHz

InP/In/sub 0.53/Ga/sub 0.47/As/InP double heterojunction bipolar transistors (DHBT) have been designed for increased bandwidth digital and analog circuits, and fabricated using a conventional mesa structure. These devices exhibit a maximum 450 GHz f/sub /spl tau// and 490 GHz f/sub max/, which is the highest simultaneous f/sub /spl tau// and f/sub max/ for any HBT. The devices have been scaled vertically for reduced electron collector transit time and aggressively scaled laterally to minimize the base-collector capacitance associated with thinner collectors. The dc current gain /spl beta/ is /spl ap/ 40 and V/sub BR,CEO/=3.9 V. The devices operate up to 25 mW//spl mu/m/sup 2/ dissipation (failing at J/sub e/=10 mA//spl mu/m/sup 2/, V/sub ce/=2.5 V, /spl Delta/T/sub failure/=301 K) and there is no evidence of current blocking up to J/sub e//spl ges/12 mA//spl mu/m/sup 2/ at V/sub ce/=2.0 V from the base-collector grade. The devices reported here employ a 30-nm highly doped InGaAs base, and a 120-nm collector containing an InGaAs/InAlAs superlattice grade at the base-collector junction.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Evidence and understanding of ALD HfO/sub 2/-Al/sub 2/O/sub 3/ laminate MIM capacitors outperforming sandwich counterparts

Metal-insulator-metal capacitors with atomic-layer-deposited HfO/sub 2/-Al/sub 2/O/sub 3/ laminated and sandwiched dielectrics have been compared, for the first time, for analog circuit applications. The experimental results indicate that significant improvements can be obtained using the laminated dielectrics, including an extremely low leakage current of 1/spl times/10/sup -9/ A/cm/sup 2/ at 3.3V and 125/spl deg/C, a high breakdown electric field of /spl sim/3.3MV/cm at 125/spl deg/C, good polarity-independent electrical characteristics, while retaining relatively high capacitance density of 3.13 fF//spl mu/m/sup 2/ as well as voltage coefficients of capacitance as low as -80 ppm/V and 100 ppm/V/sup 2/ at 100 kHz. The underlying mechanism is likely due to alternate insertions of Al/sub 2/O/sub 3/ layers that reduce the thickness of each HfO/sub 2/ layer, hereby efficiently inhibiting HfO/sub 2/ crystallization, and blocking extensions of grain boundary channels from top to bottom as well as to achieve good interfacial quality.     

High-temperature thermal stability performance in /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As metamorphic HEMT

We report, to our knowledge, the best high-temperature characteristics and thermal stability of a novel /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As--GaAs metamorphic high-electron mobility transistor. High-temperature device characteristics, including extrinsic transconductance (g/sub m/), drain saturation current density (I/sub DSS/), on/off-state breakdown voltages (BV/sub on//BV/sub GD/), turn-on voltage (V/sub on/), and the gate-voltage swing have been extensively investigated for the gate dimensions of 0.65/spl times/200 /spl mu/m/sup 2/. The cutoff frequency (f/sub T/) and maximum oscillation frequency (f/sub max/), at 300 K, are 55.4 and 77.5 GHz at V/sub DS/=2 V, respectively. Moreover, the distinguished positive thermal threshold coefficient (/spl part/V/sub th///spl part/T) is superiorly as low as to 0.45 mV/K.     

A high-density MIM capacitor (13 fF//spl mu/m/sup 2/) using ALD HfO/sub 2/ dielectrics

Metal-insulator-metal (MIM) capacitors with different HfO/sub 2/ thickness have been investigated. The results show that both the capacitance density and voltage coefficients of capacitance (VCCs) increase with decreasing HfO/sub 2/ thickness. In addition, it is found that the VCCs decrease logarithmically with increasing thickness. Furthermore, the MIM capacitor with 10-nm HfO/sub 2/ shows a record high capacitance density of 13 fF//spl mu/m/sup 2/ and a VCC of 607 ppm/V, which can meet the requirement of the International Technology Roadmap for Semiconductors. It can also provide a low leakage current of 5.95 /spl times/ 10/sup -8/A/cm/sup 2/ at room temperature at 1 V, low tangent values below 0.05, and a small frequency dependence. These results indicate that the devices are suitable for use in silicon integrated circuit applications.