ZnO thin films prepared by pulsed laser deposition

Zinc oxide (ZnO) thin films were deposited on soda lime glass substrates by pulsed laser deposition (PLD) in an oxygen-reactive atmosphere. The structural, optical, and electrical properties of the as-prepared thin films were studied in dependence of substrate temperature and oxygen pressure. High quality polycrystalline ZnO films with hexagonal wurtzite structure were deposited at substrate temperatures of 100 and 300 °C. The RMS roughness of the deposited oxide films was found to be in the range 2-9 nm and was only slightly dependent on substrate temperature and oxygen pressure. Electrical measurements indicated a decrease of film resistivity with the increase of substrate temperature and the decrease of oxygen pressure. The ZnO films exhibited high transmittance of 90% and their energy band gap and thickness were in the range 3.26-3.30 eV and 256-627 nm, respectively.     

Properties of amorphous Si thin film anodes prepared by pulsed laser deposition

Amorphous Si (a-Si) thin film anodes were prepared by pulsed laser deposition (PLD) at room temperature. Structures and properties of the thin films were investigated using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and electrochemical measurements. Galvanostatic charge/discharge tests of half cells using lithium counter electrode were conducted at a constant current density of 100 μA/cm² in different voltage windows. Cyclic voltammetry (CV) was obtained between 0 and 1.5 V at various scan rates from 0.1 to 2 mV/s. The apparent diffusion coefficient (D_Li) calculated from the CV measurements was about ∼10⁻¹³ cm²/s. The Si thin film anode was also successfully coupled with LiCoO₂ thin film cathode. The a-Si/LiCoO₂ full cell showed stable cycle performance between 1 and 4 V.     

ITO thin films deposited by advanced pulsed laser deposition

Indium tin oxide thin films were deposited by computer assisted advanced PLD method in order to obtain transparent, conductive and homogeneous films on a large area. The films were deposited on glass substrates. We studied the influence of the temperature (room temperature (RT)-180 °C), pressure (1-6 × 10^− 2 Torr), laser fluence (1-4 J/cm²) and wavelength (266-355 nm) on the film properties. The deposition rate, roughness, film structure, optical transmission, electrical conductivity measurements were done. We deposited uniform ITO thin films (thickness 100-600 nm, roughness 5-10 nm) between RT and 180 °C on a large area (5 × 5 cm²). The films have electrical resistivity of 8 × 10^− 4 Ω cm at RT, 5 × 10^− 4 Ω cm at 180 °C and an optical transmission in the visible range, around 89%.     

High quality amorphous indium zinc oxide thin films synthesized by pulsed laser deposition

Indium zinc oxide films were grown from targets with two different In atomic concentration [In/(In + Zn)] of 40% and 80% by the pulsed laser deposition technique on glass substrates from room temperature up to 100 °C. X-ray diffraction and reflectometry investigations showed that films were amorphous and dense. Thin films (thickness < 100 nm) exhibited higher optical transmittance and resistivities than thick films (thickness > 1000 nm), probably caused by a significant decrease of oxygen vacancies due to atmosphere exposure. Films deposited from the In rich target under an oxygen pressure of 1 Pa exhibited optical transmittance higher than 85%, resistivities around 5- 7 × 10^− 4 Ω cm and mobilities in the 47-54 cm²/V s range.     

Properties of aluminum oxide thin films deposited by pulsed laser deposition and plasma enhanced chemical vapor deposition

The chemical, structural, mechanical and optical properties of thin aluminum oxide films deposited at room temperature (RT) and 800 °C on (100) Si and Si-SiO₂ substrates by pulsed laser deposition and plasma enhanced chemical vapor deposition are investigated and compared. All films are smooth and near stoichiometric aluminum oxide. RT films are amorphous, whereas γ type nano-crystallized structures are pointed out for films deposited at 800 °C. A dielectric constant of ∼ 9 is obtained for films deposited at room temperature and 11-13 for films deposited at 800 °C. Young modulus and hardness are in the range 116-254 GPa and 6.4-28.8 GPa respectively. In both cases, the results show that the deposited films have very interesting properties opening applications in mechanical, dielectric and optical fields.     

Effect of oxygen partial pressure on microstructural and optical properties of titanium oxide thin films prepared by pulsed laser deposition

Nanocrystalline titanium oxide (TiO₂) thin films were deposited on silicon (1 0 0) and quartz substrates at various oxygen partial pressures (1 × 10⁻⁵ to 3.5 × 10⁻¹ mbar) with a substrate temperature of 973 K by pulsed laser deposition. The microstructural and optical properties were characterized using Grazing incidence X-ray diffraction, atomic force microscopy, UV–visible spectroscopy and photoluminescence. The X-ray diffraction studies indicated the formation of mixed phases (anatase and rutile) at higher oxygen partial pressures (3.5 × 10⁻² to 3.5 × 10⁻¹ mbar) and strong rutile phase at lower oxygen partial pressures (1 × 10⁻⁵ to 3.5 × 10⁻³ mbar). The atomic force microscopy studies showed the dense and uniform distribution of nanocrystallites. The root mean square surface roughness of the films increased with increasing oxygen partial pressures. The UV–visible studies showed that the bandgap of the films increased from 3.20 eV to 3.60 eV with the increase of oxygen partial pressures. The refractive index was found to decrease from 2.73 to 2.06 (at 550 nm) as the oxygen partial pressure increased from 1.5 × 10⁻⁴ mbar to 3.5 × 10⁻¹ mbar. The photoluminescence peaks were fitted to Gaussian function and the bandgap was found to be in the range ∼3.28–3.40 eV for anatase and 2.98–3.13 eV for rutile phases with increasing oxygen partial pressure from 1 × 10⁻⁵ to 3.5 × 10⁻¹ mbar.     

Characterization of Al2O3/ZrO2 nano multilayer thin films prepared by pulsed laser deposition

Microstructural characterization of pulsed laser deposited Al₂O₃/ZrO₂ multilayers on Si (1 0 0) substrates at an optimized oxygen partial pressure of 3 × 10⁻² mbar and at room temperature (298 K) has been carried out. A nanolaminate structure consisting of alternate layers of ZrO₂ and Al₂O₃ with 40 bi-layers was fabricated at different zirconia layer thicknesses (20, 15 and 10 nm). The objective of the work is to study the effect of ZrO₂ layer thickness on the stabilization of tetragonal ZrO₂ phase for a constant Al₂O₃ layer thickness of 5 nm. The Al₂O₃/ZrO₂ multilayer films were characterized using high temperature X-ray diffraction (HTXRD) in the temperature range 298–1473 K. The studies showed that the thickness of the zirconia layer has a profound influence on the crystallization temperature for the formation of tetragonal zirconia phase. The tetragonal phase content increased with the decrease of ZrO₂ layer thickness. The cross-sectional transmission electron microscope (XTEM) investigations were carried out on a multilayer thin films deposited at room temperature. The XTEM studies showed the formation of uniform thickness layers with higher fraction of monoclinic and small fraction of tetragonal phases of zirconia and amorphous alumina.     

Uniformity of gallium doped zinc oxide thin film prepared by pulsed laser deposition

Recently, transparent conducting oxide thin films have attracted attention for the application to transparent conducting electrodes. In this work, we evaluated the uniformity of electrical, optical and structural properties for gallium doped zinc oxide thin films prepared on the 10 × 10 cm² silica glass substrate by pulsed laser deposition. The resistivity, carrier concentration, mobility, bonding state and atomic composition of the film were uniform along in-plane and depth direction over the 10 × 10 cm² area of the substrate. The film showed the average transmittance of 81-87%, resistivity of 1.4 × 10^− 3 Ω cm, carrier concentration of 9.7 × 10²⁰/cm³ and mobility of 5 cm²/Vs in spite of the amorphous X-ray diffraction pattern. The gradual thickness distribution was found, however, the potential for large-area and low temperature deposition of transparent conducting oxide thin film using pulsed laser deposition method was confirmed.     

A study of microstructural and optical properties of nanocrystalline ceria thin films prepared by pulsed laser deposition

Thin films of cerium oxide (CeO₂) have been deposited on (100) Si substrates using pulsed laser deposition technique at various substrate temperatures from room temperature (RT) to 973 K at an optimized oxygen partial pressure of 3 Pa. Structural, morphological and optical properties have been carried out using X-ray diffraction (XRD), Raman, ellipsometry and atomic force microscopy techniques. XRD results showed that the deposited films are polycrystalline with cubic structure. At room temperature, the film showed preferred orientation along (111) plane, while at higher temperatures, it exhibited preferred orientation along (200). The crystallite sizes were calculated and were found to be in the range 17-52 nm. The texture coefficient for (200) reflection increased until 573 K, and then decreased in the temperature range 673-973 K. The Raman peak appeared at 463 cm^− 1 due to the F_2g active mode also confirmed the formation of CeO₂ with a cubic structure. There was a systematic variation in the Raman peak intensity, frequency shift and line broadening with the increase of temperature. The ellipsometry studies showed that the refractive index and band gap increased from 2.2 to 2.6 and 3.4 to 3.6 eV, respectively with increasing substrate temperature from RT to 973 K.     

Structural and optical properties of tellurite thin film glasses deposited by pulsed laser deposition

Tellurite (TeO₂-TiO₂-Nb₂O₅) thin film glasses have been produced by pulsed laser deposition at room temperature at laser energy densities in the range of 0.8-1.5 J/cm² and oxygen pressures in the range of 3-11 Pa. The oxygen concentration in the films increases with laser energy density to reach values very close to that of the bulk glass at 1.5 J/cm², while films prepared at 1.5 J/cm² and pressures above 5 Pa show oxygen concentration in excess of 10% comparing to the glass. X-ray photoelectron spectroscopy shows the presence of elementary Te in films deposited at O₂ pressures ≤ 5 Pa that is not detected at higher pressures, while analysis of Raman spectra of the samples suggests a progressive substitution of TeO₃ trigonal pyramids by TeO₄ trigonal bipyramids in the films when increasing their oxygen content. Spectroscopic ellipsometry analysis combined with Cauchy and effective medium modeling demonstrates the influence of these compositional and structural modifications on the optical response of the films. Since the oxygen content determines their optical response through the structural modifications induced in the films, those can be effectively controlled by tuning the deposition conditions, and films having large n (2.08) and reduced k (< 10^− 4) at 1.5 μm have been produced using the optimum deposition conditions.     

脉冲激光沉积制备的HfO2薄膜的结构与电学性能

采用脉冲激光沉积（PLD）方法在Si（100）基底上制备了有效氧化层厚度为8．6nm，介电常数为29．3的HfO2薄膜．借助C射线衍射（XRD）、原子力显微镜（AFM）、高分辨透射电镜（HRTEM）分析了样品的微观结构，对电容的C-V与I-V电学特性进行了测试。实验结果表明，该方法制得的HfO2薄膜表面光滑，N2500℃下退火30mm后样品表面粗糙度由0．203nm变为0．498nm，薄膜由非晶转变为简单正交结构，界面层得到有效控制，该栅介质电容具有良好的C-V特性，较低的漏电流密度（4．3×10^-7A/cm^2，@-1V），是SiO2栅介质的理想替代物．     

Low-temperature deposition of iridium thin films by pulsed laser deposition

Extremely smooth iridium (Ir) thin films were deposited on Si(1 0 0) substrate at lower temperature than 300 °C by pulsed laser deposition (PLD) technique using Ir target in a vacuum atmosphere. The crystal orientation, surface morphology, and resistivity of the Ir thin films were systematically determined as a function of substrate temperature. Well-crystallized and single-phase Ir thin films with (1 1 1) preferred orientation were obtained at substrate temperature of 200-300 °C. The surface roughness increased with the increasing of substrate temperature. Likewise, the room-temperature resistivity of Ir thin films decreased with increasing substrate temperature, showing a low value of (10.7±0.1) μΩ cm at 300 °C.     

Metal-semiconductor transition in Nb-doped ZnO thin films prepared by pulsed laser deposition

The structural, electrical and optical properties of Nb-doped ZnO films were investigated with different Nb contents (0, 0.15, 0.31, 0.46, 0.62, and 0.94 at.%) in this article. The film with 0.46 at.% Nb content showed the lowest resistivity of 8.95 × 10^− 4 Ω cm and high transmittance about 80% with high c-axis orientation. The undoped ZnO film showed a semiconducting behavior. And Nb-doped ZnO films showed a metal-semiconductor transition (MST), which was connected with localization of degenerate electrons. The films showed metallic conductivity at temperatures closer to the ambient temperature and semiconducting behavior at lower temperatures. It was noted that the NZO films with much lower Nb concentration of 0.15 at.% presented MST compared with other transparent conducting oxides films.     

Microstructure and magnetic properties of zinc ferrite thin films produced by pulsed laser deposition

Zinc ferrite thin films were deposited from a target of zinc ferrite onto a MgO substrate using XeCl excimer laser operating at 308 nm and frequency of 30 Hz. The crystallographic characterizations of the films were performed using X-ray diffraction (XRD). Microstructure, surface morphology, chemical composition and grain size, as well as surface roughness were obtained from scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and atomic force microscopy (AFM). The magnetic properties of the thin films were studied in the temperature range 5–300 K and in fields of up to 5 T using SQUID magnetometry. Data on temperature and field dependence of magnetization provide a strong evidence for superparamagnetism. Paper presented at 8 AGM of MRSI, BARC, Mumbai, 1997.     

Lipase immobilized on nanostructured cerium oxide thin film coated on transparent conducting oxide electrode for butyrin sensing

Nanostructured cerium oxide (CeO₂) thin films were deposited on transparent conducting oxide (TCO) substrate using spray pyrolysis technique with cerium nitrate salt, Ce(NO₃)₃·6H₂O as precursor. Fluorine doped cadmium oxide (CdO:F) thin film prepared using spray pyrolysis technique acts as the TCO film and hence the bare electrode. The structural, morphological and elemental characterizations of the films were carried out using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and energy dispersive X-ray analysis (EDX) respectively. The diffraction peak positions in XRD confirmed the formation of highly crystalline ceria with cubic structure and FE-SEM images showed uniform adherent films with granular morphology. The band gaps of CeO₂ and TCO were found to be 3.2 eV and 2.6 eV respectively. Lipase enzyme was physisorbed on the surface of CeO₂/TCO film to form the lipase/nano-CeO₂/TCO bioelectrode. Sensing studies were carried out using cyclic voltammetry and amperometry, with lipase/nano-CeO₂/TCO as working electrode and tributyrin as substrate. The mediator-free biosensor with nanointerface exhibited excellent linearity (0.33–1.98 mM) with a lowest detection limit of 2 μM with sharp response time of 5 s and a shelf life of about 6 weeks.     

Application of pulsed laser deposited zinc oxide films to thin film transistor device

Transparent zinc oxide (ZnO) thin films were deposited on various substrates using a pulsed laser deposition (PLD) technique. During the PLD, oxygen pressure and substrate temperature were varied in order to find an optimal preparation condition of ZnO for thin film transistor (TFT) application. Dependence of optical, electrical and crystalline properties on the deposition conditions was investigated. The ZnO thin films were then deposited on SiN/c-Si layer structures in order to fabricate a TFT device. The pulsed laser deposited ZnO films showed a remarkable TFT performance: field effect mobility (μ_FE) of 2.4-12.85 cm²/V s and ratio of on and off current (R_on/off) in 2-6 order range. Influence of ZnO preparation conditions on the resulting TFT performance was discussed.     

Nano-polycrystalline vanadium oxide thin films prepared by pulsed laser deposition

Nano-polycrystalline vanadium oxide thin films have been successfully produced by pulsed laser deposition on Si(100) substrates using a pure vanadium target in an oxygen atmosphere. The vanadium oxide thin film is amorphous when deposited at relatively low substrate temperature (500 degrees C) and enhancing substrate temperature (600-800 degrees C) appears to be efficient in crystallizing VOx thin films. Nano-polycrystalline V3O7 thin film has been achieved when deposited at oxygen pressure of 8 Pa and substrate temperature of 600 degrees C. Nano-polycrystalline VO2 thin films with a preferred (011) orientation have been obtained when deposited at oxygen pressure of 0.8 Pa and substrate temperatures of 600-800 degrees C. The vanadium oxide thin films deposited at high oxygen pressure (8 Pa) reveal a mix-valence of V5+ and V4+, while the VOx thin films deposited at low oxygen pressure (0.8 Pa) display a valence of V4+. The nano-polycrystalline vanadium oxide thin films prepared by pulsed laser deposition have smooth surface with high qualities of mean crystallite size ranging from 30 to 230 nm and Ra ranging from 1.5 to 22.2 nm. Relative low substrate temperature and oxygen pressure are benifit to aquire nano-polycrystalline VOx thin films with small grain size and low surface roughness.     

Structural and textural characterization of LiFePO4 thin films prepared by pulsed laser deposition on Si substrates

LiFePO₄ thin films were grown on silicon (100) substrates by pulsed laser deposition using Traditional Geometry (TG) and Off-Axis Geometry (OAG) deposition chambers. We examined and compared the structure and composition of the so formed thin films. The nails observed on the OAG-film present an amorphous “body” and a crystallized “head”. The Fe/P ratio determined using energy dispersive spectrometry combined with high angle annular dark field images reveals a metallic iron heart surrounded by LiFePO₄ shell. On the other hand, the protuberances on TG-film are pure iron. The focused ion beam prepared cross-section of the film suggests the presence of iron particles and iron dendritic like filaments inside the LiFePO₄ layer.     

Excimer laser deposition and characteristics of tin oxide thin films

ArF excimer laser assisted chemical vapor deposition of tin oxide thin films on Si was obtained using SnCl₄ and O₂ as precursors. Experimental measurements revealed that the deposition rate increases with incident laser energy density. The composition, structure and ultraviolet-to-visible spectra of the thin films were investigated by means of XPS, SEM, XRD and a UV–Vis techniques. It was shown that SnO₂ and SnOCl₂ coexisted in the thin films, and SnOCl₂ was almost completely converted into SnO₂ after annealing. The SnO₂ thin films deposited at room temperature were amorphous in structure and the grain size of the films became larger after annealing. The transmittance of the SnO₂ thin films is above 90%, the absorption edge is 355 nm and the energy gap is 3.49 eV.