Effect of cadmium oxide incorporation on the microstructural and optical properties of pulsed laser deposited nanostructured zinc oxide thin films

CdO doped (doping concentration 0, 1, 3 and 16 wt%) ZnO nanostructured thin films are grown on quartz substrate by pulsed laser deposition and the films are annealed at temperature 500 °C. The structural, morphological and optical properties of the annealed films are systematically studied using grazing incidence X-ray diffraction (GIXRD), energy dispersive X-ray analysis (EDX), scanning electron microscopy (SEM), atomic force microscopy (AFM), Micro-Raman spectra, UV–vis spectroscopy, photoluminescence spectra and open aperture z-scan. 1 wt% CdO doped ZnO films are annealed at different temperatures viz., 300, 400, 500, 600, 700 and 800 °C and the structural and optical properties of these films are also investigated. The XRD patterns suggest a hexagonal wurtzite structure for the films. The crystallite size, lattice constants, stress and lattice strain in the films are calculated. The presence of high-frequency E₂ mode and the longitudinal optical A₁ (LO) modes in the Raman spectra confirms the hexagonal wurtzite structure for the films. The presence of CdO in the doped films is confirmed from the EDX spectrum. SEM and AFM micrographs show that the films are uniform and the crystallites are in the nano-dimension. AFM picture suggests a porous network structure for 3% CdO doped film. The porosity and refractive indices of the films are calculated from the transmittance and reflectance spectra. Optical band gap energy is found to decrease in the CdO doped films as the CdO doping concentration increases. The PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. The 16CdZnO film shows an intense deep green PL emission. Non-linear optical measurements using the z-scan technique indicate that the saturable absorption (SA) behavior exhibited by undoped ZnO under green light excitation (532 nm) can be changed to reverse saturable absorption (RSA) with CdO doping. From numerical simulations the saturation intensity (I_s) and the effective two-photon absorption coefficient (β) are calculated for the undoped and CdO doped ZnO films.     

Fabrication of a novel organic polymer thin film

Fabrication of organic polymer thin films and organic semiconductors are critical for the development of sophisticated organic thin film based devices. Radio Frequency plasma polymerisation is a well developed and widely used fabrication technique for polymer thin films. This paper describes the fabrication of an organic polymer thin film from a monomer based on Lavandula angustifolia. Several polymer thin films were manufactured with thicknesses ranging from 200 nm to 2400 nm. The energy gap of the polymer thin film was measured to be 2.93 eV. The refractive index and extinction coefficient was determined to be 1.565 (at 500 nm) and 0.01 (at 500 nm) respectively. The organic polymer thin film demonstrates the possibility of an environmentally friendly, cost effective organic semiconductor.     

Stability,UV shielding properties,and light conversion behavior of Eu(BMDM)3@polysiloxane nanoparticles in water and polyurethane films

Bifunctional Eu(BMDM)₃@polysiloxane nanoparticles were prepared through reprecipitation–encapsulation methods using 1-(4-tert-butylphenyl)-3-(4-methoxyphenyl)-1,3-propanedione (BMDM) ligand and octyltrimethoxysilane (OTS) precursor and embedded into waterborne polyurethane (PU) coatings to fabricate transparent optical composite films. The photostability and thermostability of the nanoparticles in water and their ability to block UV and convert light when embedded in PU films were investigated. In comparison with the control Eu(BMDM)₃ nanoparticles, the Eu(BMDM)₃@polysiloxane nanoparticles, especially those prepared at a Eu(BMDM)₃/OTS mole ratio of 1:2, exhibited far superior stability under storage conditions, UV irradiation, and heating. They also showed excellent UV-shielding and highly efficient light conversion properties because of the protective polysiloxane.     

Gamma-irradiation-induced Ag/SiO2 composite films and their optical absorption properties

Small Ag particles or clusters dispersed mesoporous SiO₂ composite films were prepared by a new method: First the matrix SiO₂ films were prepared by sol-gel process combined with the dip-coating technique, then they were soaked in AgNO₃ solutions followed by irradiation of γ-ray at room temperature and in ambient pressure. The structures of these films were examined by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), and optical absorption spectroscopy. It has been shown that the Ag particles grown within the porous SiO₂ films are very small, and they are isolated and dispersed from each other with very narrow size distributions. With increasing the soaking concentration and an additional annealing, an opposite peakshift effect of the surface plasmon resonance (SPR) was observed in the optical absorption measurements.     

Electro-optical properties of poly[di(2-thiophenyl)carborane] and its opto-electronic application

Electrochemical and optical properties of a hybrid carborane based polymer called poly(di(2-thiophenyl)carborane) (P1) obtained electrochemically were reported as well as its electrochromic device application. Thiophene donor units and m-carborane acceptor unit were combined under the same umbrella via donor–acceptor–donor approach to obtain di(2-thiophenyl)carborane (1). Contrary to the literature, extreme conditions like highly dried solvent or inert atmosphere were not used for polymerization and characterization. Polymer P1 has an ambipolar character since it exhibited a reversible oxidation peak at a half wave potential (E_1/2) of 1.08 V and a quasi reversible reduction peak at E_1/2 = −1.82 V vs. Ag/AgCl. The polymer film has an optical band gap of 1.95 eV with a maximum absorption band centered at 488 nm. Also, it exhibited multicolor electrochromic behavior between its reduced and oxidized states changing from dark orange to light blue. Furthermore, the electrochromic device prepared based on P1 film was stable and robust.     

Fabrication of surface silvered polyimide/iron oxide composite films with both superparamagnetism and electrical conductivity

Surface silvered polyimide (PI)/Fe₂O₃ composite films with both superparamagnetic and surface electrically conductive properties have been fabricated by an in situ technique. Iron (III) 2,4-pentanedionate was incorporated into a PI precursor poly(amic acid) solution and thermally decomposed to form iron oxide nanoparticles in the process of thermal imidization, preparing PI/Fe₂O₃ nanocomposite films. The establishment of a silver layer on the PI/Fe₂O₃ film surface involved the steps of chemical etching by the alkaline aqueous solution, ion exchange with silver ions and chemical reduction by glucose. The formed Fe₂O₃ particles of the nano scale endow the film with typical superparamagnetic response. By employing the etching time of only 10 min and a reduction time of no more than 15 min, the well-established silver layers have formed on the upside surface. The corresponding reflectivity and resistivity reached to the value of 76.15% and 0.7 Ω/square respectively.     

Indium(III) and Gallium(III) phthalocyanines-based nanohybrid materials for optical limiting

Linear and nonlinear optical properties of a phthalocyanine (Pc)-based nanohybrid material PCIGS [Cu₂(tBu₄PcGa)(tBu₄PcIn)S₂TPP₂] are described. The overall aggregation of phthalocyanines in poly(methylmethacrylate) (PMMA) films was evident, which is indicated by the broadening of linear spectra in the Q-band region and the shift of wavelength. Upon excitation with nanosecond laser pulse at 355 nm, the transient absorption band appeared at about 500 nm is attributed to the triplet–triplet absorption of the Pcs. For PCIGS and its starting materials tBu₄PcGaCl and tBu₄PcInCl, all Z-scans exhibit a decrease in transmittance about the focus typical of an induced positive nonlinear absorption of incident light. The absorption mechanism is due to population of excited states through a multi-step nonlinear absorption. When these Pc compounds were embedded into a commercially available polymer PMMA, all the Pc/PMMA composites display much larger nonlinear absorption coefficient and lower saturable fluence for optical limiting when compared to the same Pc molecules in solution. However, in contrast to tBu₄PcGaCl and tBu₄PcInCl, PCIGS displayed decreased optical limiting response, possibly due to competing electron accepting processes in the In and Ga metals, and the highly ordered structure of the PCIGS complex itself.     

Synthesis and super capacitance of goethite/reduced graphene oxide for supercapacitors

We report a one-step fabrication of α-iron oxyhydroxide/reduced graphene oxide (α-FeOOH/rGO) composites, in which the ferrous sulfate (FeSO₄·7H₂O) are used as the iron raw and reducing agent to grow goethite (α-FeOOH) and reduce graphite oxide (GO) to rGO in the same time. The morphology, composition and microstructure of the as-obtained samples are systematically characterized by thermogravimetric (TG) analysis, field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and FT-IR. Moreover, their electrochemical properties are investigated using cyclic voltammetry and galvanostatic charge/discharge techniques. The specific capacitance of 452 F g⁻¹ is obtained at a specific current of 1 A g⁻¹ when the mass ratio of α-FeOOH to rGO is up to 80.3:19.7. In addition, the α-FeOOH/rGO composite electrodes exhibit the excellent rate capability (more than 79% retention at 10 A g⁻¹ relative to 1 A g⁻¹) and well cycling stability (13% capacitance decay after 1000 cycles). These results suggest the importance and great potential of α-FeOOH/rGO composites in the applications of high-performance energy-storage.     

Optoelectronic properties of graphene thin films prepared by thermal reduction of graphene oxide

Graphene thin films have been prepared by thermal reduction of graphene oxide. Raising the reduction temperature results in a red-shift of the G peak in Raman spectra. The reduction temperature turns out to strongly affect the morphology of the prepared graphene film. Photoluminescence (PL) results show that the band gap of graphene can be tuned by varying the reduction temperature. The thermal reduction process has been optimized in an effort to minimize the formation of wrinkles/folds on the graphene surface leading to enhanced PL and Raman peak intensities and reduced electrical sheet resistance.     

Co2SnO4/activated carbon composite electrode for supercapacitor

A new kind of Co₂SnO₄-based electrode materials for supercapacitor was synthesized by co-precipitation method. The microstructure and surface morphology of Co₂SnO₄ were characterized by X-ray diffraction and scanning electron microscopy, respectively. Cyclic voltammetry, chronopotentiometry and electrochemical impedance spectroscopy were employed for the determination of specific capacitance and the equivalent series resistance of Co₂SnO₄/activated carbon composite electrode in KCl solution. It was shown that the composite electrode with 25 wt% Co₂SnO₄ had excellent specific capacitance up to 285.3 F g⁻¹ at the current density of 5 mA cm⁻². In addition, the composite electrode exhibited excellent long-term stability and, after 1000 cycles, 70.6% of initial capacitance was retained. Regarding the low cost, easy preparation, steady performance and environment friendliness, Co₂SnO₄/activated carbon composite electrode could have potentially promising application for supercapacitor.     

Electrodeposition PbO2-TiO2 and PbO2-ZrO2 and its physicochemical properties

Composite materials based on PbO₂ containing TiO₂ or ZrO₂ were prepared from electrolytes containing a suspension of TiO₂ or ZrO₂. The contents of foreign oxides in the composite depend on the electrolyte composition and conditions of deposition. When a dispersed phase is incorporated into the composite coating, the dimensions of lead dioxide crystals decrease to submicro- and nano-size. Physico-chemical properties of composite materials are mainly determined by their chemical composition.     

Manganese oxide thin films prepared by pulsed laser deposition for thin film microbatteries

Manganese oxide thin films with various oxidation states (MnO, Mn₃O₄ and Mn₂O₃) have been prepared by pulsed laser deposition using a Mn target at different oxygen partial pressures. The structural and morphological features of the as-deposited thin films are characterized by X-ray diffraction, Raman, field emission scanning electron microscopy (FESEM). The oxidation states of Mn in different thin films are investigated by X-ray photoelectron spectroscopy for both Mn 2p and 3s levels. It is found that the structure, surface morphology, and Mn oxidation state of the thin films can be tuned by oxygen partial pressure during the deposition. As anode for thin film lithium-ion microbatteries, the Mn₃O₄ thin film electrode exhibits the largest reversible capacity up to 800 mAh g⁻¹ with good cycling stability and excellent rate capability. The promising electrochemical performance of the Mn₃O₄ thin film electrode indicates the potential application of Mn₃O₄ thin film anode in all solid-state thin film microbatteries.     

Structure, morphology and magnetic properties of Fe-B-Si-Nb glassy alloy thin film prepared by a pulsed laser deposition method

With the aim of applying to a soft magnetic underlayer of the double-layered perpendicular magnetic recording media, an Fe_74.9B_17.5Si_2.5Nb_5.1 alloy thin film was fabricated on Si substrate by a pulsed laser deposition method. The Fe-based alloy thin film of 200 nm in thickness was confirmed as a glassy structure. The thermal properties of the thin film have similar features to those for the melt-spun glassy alloy ribbon. The glassy alloy thin film exhibits good soft magnetic properties, i.e., high B_s of 1.2 T and in-plane low H_c of 134 A/m. The Fe-B-Si-Nb glassy alloy thin film is expected to be suitable for the soft magnetic underlayer material in the double-layered perpendicular magnetic recording media.     

Synthesis, characterization and optical properties of mono- and bis-chalcone

Mono- and bis-chalcone have been synthesized by the reaction of 3-acetyl-2,5-dimethylthiophene and N, N-di-methylbenzaldehyde/terephthalaldehyde in ethanolic NaOH in microwave oven. The structure of these compounds was established by elemental analysis, IR, ¹H NMR, ¹³ C NMR and GC-MS spectral analysis. Thin films with thickness of 100 nm of mono- and bis-chalcone were evaporated by thermal evaporation onto glass/Si wafer substrates under a vacuum of 10^− 6 Torr. The optical constants (absorption coefficient and optical band gap) of these films have been studied as a function of photon energy in the wavelength region 300-1100 nm. Analysis of the optical absorption data shows that the rule of non-direct transitions predominates. The optical band gaps for mono- and bis-chalcone are found to be 2.31 and 0.99 eV respectively. It has been found that the absorption coefficient changes with increasing photon energy. The peak values of the absorption coefficient are found to be at 370 nm for mono-chalcone and 460 nm for bis-chalcone thin films.     

Cu2O nanorod thin films prepared by CBD method with CTAB: Substrate effect,deposition mechanism and photoelectrochemical properties

Cuprous oxide (Cu₂O) films with different nanostructures are deposited on different substrates of fluorine-doped SnO₂ (FTO) glass, Cu and Ti foil respectively by using chemical bath deposition (CBD) technique with the presence of cetyltrimethylammonium bromide (CTAB). The samples are characterized by X-ray diffractmeter, scanning electron microscopy and UV–vis diffuse reflectance spectroscopy. The results show that the prepared Cu₂O films are composed of nanorod arrays when there is CTAB in reaction system. Without CTAB, Cu₂O films with nanospheres are formed. The concentration of CTAB is crucial for the controllable synthesis of nanorod structured Cu₂O films with different length to diameter ratio and nanorod array density is dependent on both substrates and CTAB. A possible mechanism for the formation of Cu₂O nanorods is discussed. Additionally, the UV–vis absorption property for Cu₂O nanorods is much better than that for nanospheres. The photovoltage produced under visible light for Cu₂O nanorod films is higher than that for the nanospheres. Although Cu₂O nanorods on Ti foil can absorb the most visible light, those on Cu foil demonstrate better and more stable photoelectrochemical property than those on any other substrates. This study may be extremely useful for Cu₂O based device with nanostructures.     

Electrical and electrochemical properties of poly(2,5-dimercapto-1,3,4-thiadiazole)-polyaniline adduct intercalated graphite oxide composites

Poly(2,5-dimercapto-1,3,4-thiadiazole-polyaniline) adduct (PDMcT-PANI) was synthesized by chemical oxidative polymerization. It indicates that electrons are transferred between the PANI and the PDMcT to form the electron donor-acceptor adduct. PDMcT-PANI intercalated graphite oxide composites (PDMcT-PANI/GO) were synthesized by delamination/reassembling method. The hydrogen bond is formed between the –NH and –SH groups of PDMcT-PANI and the carboxyl groups at the edges of the GO, which is confirmed by FTIR. XRD and TEM results show that the PDMcT-PANI/GO composites still maintain good lamellar structure after intercalation, and the interlayer spacing (I_c values) of the GO is enlarged with the addition of the PDMcT-PANI. PDMcT-PANI/GO composites provide better thermal stability compared with pristine GO and PDMcT-PANI. In addition, the intercalation of PDMcT-PANI also improves the electrical conductivity and electrochemical properties of the composites.     

Zinc cadmium oxide thin film transistors fabricated at room temperature

Zinc cadmium oxide (ZnCdO) transparent thin film transistors (TFTs) have been fabricated with a back-gate structure using highly p-type Si (001) substrate. For the active channel, 30 nm, 50 nm, and 100 nm thick ZnCdO thin films were grown by pulsed laser deposition. The ZnCdO thin films were wurtzite hexagonal structure with preferred growth along the (002) direction. All the samples were found to be highly transparent with an average transmission of about 80%~ in the visible range. We have investigated the change of the performance of ZnCdO TFTs as the thickness of the active layer is increased. The carrier concentration of ZnCdO thin films has been confirmed to be increased from 10¹⁶ to 10¹⁹ cm⁻³ as the film thickness increased from 30 to 100 nm. Base on this result, the ZnCdO TFTs show a thickness-dependent performance which is ascribed to the carrier concentration in the active layer. The ZnCdO TFT with 30 nm active layer showed good off-current characteristic of below ~ 10¹¹, threshold voltage of 4.69 V, a subthreshold swing of 4.2 V/decade, mobility of 0.17 cm²/V s, and on-to-off current ratios of 3.37 × 10⁴.     

Fabrication of toughened Cf/SiC whisker composites and their mechanical properties

In this paper, dense short carbon fiber reinforced silicon carbide matrix composites had been fabricated by hot-pressed (HP) sintering using Al₂O₃ and La₂O₃ as sintering additives. The results showed that the combination of Al₂O₃ and La₂O₃ system was effective to promote densification of short cut carbon fiber reinforced silicon carbide composites (Cf/SiC). The whisker structure of silicon carbide was formed during the annealed treatment at 2023 K for 1 h. However, it was noted that this structure was not observed in the as-received HP material. The mechanism of forming whisker structure was not clear, but this kind of whisker structure was helpful to improve mechanical properties. The combination of grain bridging, crack deflection and whisker debonding would improve the fracture toughness of the Cf/SiC composites.     

Energy dependent saturable and reverse saturable absorption in cube-like polyaniline/polymethyl methacrylate film

Solid films of cube-like polyaniline synthesized by inverse microemulsion polymerization method have been fabricated in a transparent PMMA host by an in situ free radical polymerization technique, and are characterized by spectroscopic and microscopic techniques. The nonlinear optical properties are studied by open aperture Z-scan technique employing 5 ns (532 nm) and 100 fs (800 nm) laser pulses. At the relatively lower laser pulse energy of 5 μJ, the film shows saturable absorption both in the nanosecond and femtosecond excitation domains. An interesting switchover from saturable absorption to reverse saturable absorption is observed at 532 nm when the energy of the nanosecond laser pulses is increased. The nonlinear absorption coefficient increases with increase in polyaniline concentration, with low optical limiting threshold, as required for a good optical limiter.