Synthesis and characterizations of Nd doped SrFe12O19 nanoparticles

This is the first report ever on Nd³⁺ doped M-type hexaferrite nanoparticles: SrNd_xFe_12−xO₁₉ (0 ≤ x ≤ 1) prepared by citrate precursor using the sol–gel technique followed by gel to crystallization. The influence of the Nd³⁺ substitution, Fe³⁺/Sr²⁺ molar ratio and the calcination temperature on the crystallization of ferrite phase have been examined using powder X-ray diffraction (XRD), scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), inductance capacitance resistance meter bridge (LCR) and vibrating sample magnetometer (VSM). The structural analysis reveals that the Nd³⁺ ions rearrange themselves in the host lattice without disturbing the parent lattice and Fe³⁺/Sr²⁺ molar ratio less than 12 is more favorable to achieve single phase hexaferrite at calcination temperature 900 °C for 4 h. Mid-IR analysis confirms that Nd³⁺ occupies the octahedral site. Detailed studies of electrical properties of prepared materials have been investigated in the frequency range 100–1000 Hz at room temperature by LCR meter and two probe technique. The result shows that the electrical properties strongly depend upon the frequency of applied field and dopant concentration. The magnetic measurements showing a considerable improvement in coercivity with the substitution of Nd³⁺ on iron sites, while the unsubstituted hexaferrites have highest value of specific saturation magnetization.     

Structure and thermal conductivity of Gd2(TixZr1 − x)2O7 ceramics

The Gd₂(Ti_xZr_1 − x)₂O₇ (x = 0, 0.25, 0.50, 0.75, 1.00) ceramics were synthesized by solid state reaction at 1650 °C for 10 h in air. The relative density and structure of Gd₂(Ti_xZr_1 − x)₂O₇ were analyzed by the Archimedes method and X-ray diffraction. The thermal diffusivity of Gd₂(Ti_xZr_1 − x)₂O₇ from room temperature to 1400 °C was measured by a laser-flash method. The Gd₂Zr₂O₇ has a defect fluorite-type structure; however, Gd₂(Ti_xZr_1 − x)₂O₇ (0.25 ≤ x ≤ 1.00) compositions exhibit an ordered pyrochlore-type structure. Gd₂Zr₂O₇ and Gd₂Ti₂O₇ are infinitely soluable. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ increases with increasing Ti content under identical temperature conditions. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ first decreases gradually with the increase of temperature below 1000 °C and then increases slightly above 1000 °C. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ is within the range of 1.33 to 2.86 W m^− 1 K^− 1 from room temperature to 1400 °C.     

Synthesis of LiNi0.9Co0.1O2 cathode material for lithium secondary battery by a novel route

The cathode material, LiNi_0.9Co_0.1O₂ was prepared using a rheological phase reaction method with LiOH·H₂O, home-made Ni(OH)₂, and Co₂O₃ as starting materials. At first, the mixture of reactants and a proper amount of water reacted to form a rheological precursor. Then the dried precursor was heated at 730 °C in one step to yield the product. The effects of calcination time (between 0.5 and 10 h) on the structural, morphological and electrochemical properties were investigated. All obtained powders show a single phase with α-NaFeO₂ structure (R-3m space group). The sample prepared in 2.5 h delivers the largest initial discharge capacity of 218 mA h g^− 1 (3.0-4.35 V, 25 mA g^− 1) and still remains 192 mA h g^− 1 after 15 cycles. The method is simple, economical and effective and is promising for practical application.     

Stoichiometric Pb(Mg1/3Nb2/3)O3 perovskite ceramics produced by reaction-sintering process

Stoichiometric lead magnesium niobate, Pb(Mg_1/3Nb_2/3)O₃ (PMN), perovskite ceramics produced by reaction-sintering process were investigated. Without calcination, a mixture of PbO, Nb₂O₅, and Mg(NO₃)₂ was pressed and sintered directly. Stoichiometric PMN ceramics of 100% perovskite phase were obtained for 1, 2, and 4 h sintering at 1250 and 1270 °C. PMN ceramics with density 8.09 g/cm³ (99.5% of theoretical density 8.13 g/cm³) and K_max 19,900 under 1 kHz were obtained.     

Crystallite structure,microstructure, dielectric,and piezoelectric properties of (Pb1.06−xBax)(Nb0.94Ti0.06)2O6 piezoelectric ceramics prepared using calcined powders with different phases

In an attempt to obtain dense lead metaniobate-based ceramics with improved dielectric and piezoelectric properties, the (Pb_1.06−xBa_x)(Nb_0.94Ti_0.06)₂O₆ (x = 0, 0.04, 0.08, 0.12) piezoelectric ceramics were prepared separately from the two kinds of calcined powders, i.e., the powders with the rhombohedral phase and orthorhombic phase. For obtaining the calcined powders with the different phases, two different calcination temperatures of 900 °C and 1250 °C were chosen. The calcined powders were characterized using X-ray diffraction, scanning electron microscope, laser particle size analyzer and differential scanning calorimetry. Effects of the phase structures of the calcined powders on crystallite structure, microstructure, dielectric and piezoelectric properties of the ceramics were studied in detail. The lattice parameters and grain size of the ceramics are related to the phase structures of the calcined powders. The doping of Ba²⁺ has an influence on the dielectric and piezoelectric properties of the ceramics. The ceramics with x = 0.08 fabricated from the calcined powders with the orthorhombic phase demonstrate the optimum dielectric and piezoelectric properties.     

KxNa1 − xNbO3 powder synthesized by molten-salt process

K_xNa_1 − xNbO₃ ceramic powders have been successfully synthesized in different salts (NaCl, KCl, NaCl-KCl). Our results reveal that K_xNa_1 − xNbO₃ powders with single-phase perovskite structure can be formed at a low temperature such as 750 °C. The type of salts has significant effects on the morphology and chemical composition of the powders. As Na⁺ has a higher diffusing rate and occupies the A-site in the perovskite structure more easily as compared to K⁺, the powder contains only a small amount of K⁺ (x ∼ 0.10) when it is synthesized according to formula K_0.5Na_0.5NbO₃ and in a flux containing the same molar content of Na⁺ and K⁺. By using a NaCl or KCl salt, the K⁺ concentration x can be adjusted to almost 0 and 0.77, respectively.     

Synthesis and characterization of Ni1−xZnxFe2O4 spinel ferrites from tailored layered double hydroxide precursors

In this paper, a series of pure Ni_1 − xZn_xFe₂O₄ (0 ≤ x ≤ 1) spinel ferrites have been synthesized successfully using a novel route through calcination of tailored hydrotalcite-like layered double hydroxide molecular precursors of the type [(Ni + Zn)_{1 − x − y}Fe_y²⁺Fe_x³⁺(OH)₂]^x+(SO₄²⁻)_x/2·mH₂O at 900 °C for 2 h, in which the molar ratio of (Ni²⁺ + Zn²⁺)/(Fe²⁺ + Fe³⁺) was adjusted to the same value as that in single spinel ferrite itself. The physico-chemical characteristics of the LDHs and their resulting calcined products were investigated by powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and Mössbauer spectroscopy. The results indicate that calcination of the as-synthesized LDH precursor affords a pure single Ni_1 − xZn_xFe₂O₄ (0 ≤ x ≤ 1) spinel ferrite phase. Moreover, formation of pure ferrites starting from LDHs precursors requires a much lower temperature and shorter time, leading to a lower chance of side-reactions occurring, because all metal cations on the brucite-like layers of LDHs can be uniformly distributed at an atomic level.     

Hydrothermal formation and characteristics of rare-earth niobate phosphors and solid solutions between YNbO4 and TbNbO4

Monoclinic fergusonite-type niobate, YNbO₄:Tb³⁺ and complete solid solutions with luminescent properties in the YNbO₄–TbNbO₄ system were directly formed as nanocrystals from the precursor solutions of NbCl₅, TbCl₃, and YCl₃ under hydrothermal conditions at 240 °C. The niobate nanocrystals possessed distinguishing feature of ellipsoidal morphology. The optical band gap of the as-prepared samples, Y_1−xTb_xNbO₄, x = 0–1.0, decreased from 3.7 to 2.9 eV as the terbium concentration increased from x = 0 to 1.0. The photoluminescence spectra of the as-prepared nanocrystals containing terbium are responsible for the characteristic blue (490 nm) and green (545 nm) luminescence, associated with ⁵D₄ → ⁷F₆ and ⁵D₄ → ⁷F₅ transitions, respectively. The strongest emission bands in the green spectral domain corresponding to ⁵D₄ → ⁷F₅ transition of Tb³⁺ are located at 545 and 550 nm under excitation at 240 nm Xe lamp. By heat treatment at 1300 °C, the luminescence intensity of the as-prepared solid solution x = 0.10 that presented the highest photoluminescence intensity increased more than 8 times as high as that before heat treatment.     

Synthesis of (1 − x)Ca2/5Sm2/5TiO3-xLi1/2Nd1/2TiO3 ceramic powder via ethylenediaminetetraacetic acid precursor

(1 − x)Ca_2/5Sm_2/5TiO₃-xLi_1/2Nd_1/2TiO₃ (CSLNT) ceramic powder was prepared by a liquid mixing method using ethylenediaminetetraacetic acid (EDTA) as the chelating agent. TG, DTA, XRD and TEM characterized the precursors and derived oxide powders. When x = 0.3, perovskite CSLNT was synthesized at 1000 °C for 3 h in air. The CSLNT (x = 0.3) ceramics sintered at 1200 °C for 3 h show excellent microwave dielectric properties of ?_r = 99, Q_f = 6200 GHz and τ_f = 9 × 10⁻⁶ °C⁻¹.     

Growth of silicon carbide thin films by hot-wire chemical vapor deposition from SiH4/CH4/H2

Silicon carbide (SiC) thin films were prepared by hot-wire chemical vapor deposition from SiH₄/CH₄/H₂ and their structural properties were investigated by X-ray diffraction, Fourier transform infrared absorption and Raman scattering spectroscopies. At 2 Torr, Si-crystallite-embedded amorphous SiC (a-Si_1 − xC_x:H) grew at filament temperatures (T_f) below 1600 °C and nanocrystalline cubic SiC (nc-3C-SiC:H) grew above T_f = 1700 °C. On the other hand, At 4 Torr, a-Si_1 − xC_x:H grew at T_f = 1400 °C and nc-3C-SiC grew above T_f = 1600 °C. When the intakes of Si and C atoms into the film per unit time are almost the same and H radicals with a high density are generated, which takes place at high T_f, nc-3C-SiC grows. On the other hand, at low T_f the intake of Si atoms is larger than that of C atoms and, consequently, Si-rich a-Si_1 − xC_x:H or Si-crystallite-embedded a-Si_1 − xC_x:H grow.     

Formation, sintering, and electrical conductivity of (Nd1−xCax)CrO3 (0≤x≤0.25) using citric acid as a gelling agent

In Ca²⁺-substituted NdCrO₃, single-phase perovskite compounds (Nd_1−xCa_x)CrO₃, where x=0-0.25, have been formed by a citric acid processing. (Nd_1−xCa_x)CrO₃ powders consisting of submicrometer-size particles are sinterable; dense materials can be fabricated by sintering for 2 h at 1700°C under atmospheric pressure. The relative densities, grain sizes, and electrical conductivities increase with increased Ca²⁺ content. (Nd_0.75Ca_0.25)CrO₃ materials show an excellent electrical conductivity of 1.9×10 S m⁻¹ at 1000°C.     

Synthesis,structure and properties of heavily Mn-doped perovskite-type SrTiO3 nanoparticles

Cubic perovskite SrTi_1−xMn_xO₃ nanopowders with x = 0–0.5, which is much higher than the conventionally believed Mn incorporation limit, and particles sizes 10–80 nm have been successfully synthesized using the citrate sol–gel method. The crystalline structure, the morphology, the chemical composition and the lattice constant behavior versus the annealing temperature and the Mn concentration have been characterized using X-ray diffraction, scanning electron microscopy and proton-induced X-ray emission techniques. Studies of Raman light scattering and the magnetic properties revealed the activation of the TO2 polar mode and the magnetic ordering effects at low temperatures. Such features are treated as possible evidence of non-d⁰ Mn-driven transition to a polar phase with multiferroicity in heavily concentrated perovskite SrTi_1−xMn_xO₃ nanopowders.     

Synthesis of nanocrystalline xCuFe2O4-(1 − x)BiFeO3 magnetoelectric composite by chemical method

xCuFe₂O₄-(1 − x)BiFeO₃ spinel-perovskite nanocomposites with x = 0.1, 0.2, 0.3 and 0.4 were prepared using citrate precursor method. X-ray diffraction (XRD) analysis showed phase formation of xCuFe₂O₄-(1 − x)BiFeO₃ calcined at 500 °C. Transmission electron microscopy (TEM) shows formation of nanocrystallites of xCuFe₂O₄-(1 − x)BiFeO₃ with an average particle size of 40 nm. Variation of dielectric constant and dielectric loss with frequency showed dispersion in the low frequency range. Coercivity, saturation magnetization and squareness have been found to vary with concentration of ferrite phase and annealing temperature due to the increase in crystallite size. Squareness and coercivity increased with an increase in annealing temperature up to 500 °C and then decreased with a further increase in temperature to 600 °C. Magnetoelectric effect of the nanocomposites was found to be strongly depending on the magnetic bias and magnetic field frequency.     

Chemical diffusion coefficient of lithium ion in Li3V2(PO4)3 cathode material

The kinetic properties of monoclinic lithium vanadium phosphate were investigated by potential step chronoamperometry (PSCA) and electrochemical impedance spectroscopy (EIS) method. The PSCA results show that there exists a linear relationship between the current and the square root of the time. The D?_Li values of lithium ion in Li_3-xV₂(PO₄)₃ under various initial potentials of 3.41, 3.67, 3.91 and 4.07 V (vs Li/Li⁺) obtained from PSCA are 1.26 × 10^− 9, 2.38 × 10^− 9, 2.27 × 10^− 9 and 2.22 × 10^− 9 cm²·s^− 1, respectively. Over the measuring temperature range 15-65 °C, the diffusion coefficient increased from 2.67 × 10^− 8 cm²·s^− 1 (at 15 °C) to 1.80 × 10^− 7 cm²·s^− 1 (at 65 °C) as the measuring temperature increased.     

Effects of Bi2O3 and Cr2Ti3O9 Co-doping on dielectric properties in BaTiO3-based ceramics

A microwave ceramic with general composition (1-x-y) BaTiO₃ + x Cr₂Ti₃O₉ + y Bi₂O₃ has been prepared by solid state synthesis at 1300-1400 °C. The phase composition, perovskite structural parameters and dielectric properties have been obtained by X-ray diffraction and dielectric measurements as a function of chemical composition and temperature. At low doping levels the formation of BaTiO₃-based solid solution has been found. The precipitation of BaCrO₃ has been detected at x = y = 2.0 mol%. A model of the incorporation of Cr³⁺ and Bi³⁺ ions into BaTiO₃-based crystal lattice has been proposed. Diffused phase transition in the temperature range 100-140 °C have been revealed by dielectric measurements for different ceramic composition. As high dielectric constant as 7311 and as low dielectric loss as 0.02 have been found for the composition of 0.98BaTiO₃-0.01Cr₂Ti₃O₉-0.01Bi₂O₃.     

Synthesis and characterization of nanosized SrBi2Ta2O9 powder by a novel sol-gel process

Chemically homogeneous SrBi₂Ta₂O₉ (SBT) sol was synthesized using ethoxy tantalum, strontium acetate, and bismuth subnitrate as starting materials, methoxyethylene as a solvent and acetic acid (HOAc) as a catalyst. Single-phased perovskite phase SBT ferroelectric ultrafine powder was obtained after the dried gel was treated at 350°C for 30 min and calcined at 800°C for 1 h. FT-IR, XRD, TEM and TG-DTA were employed to investigate the transformation processes of sol to gel and gel to ultrafine SBT powder. Acetic acid not only acts as an acid catalyst, but also changes the alkoxide precursor as a ligand at a molecular level. Bidentate acetates replace OR groups and are directly bounded to the tantalum, leading to the formation of Ta (OR)_x(OAc)_5−x. The perovskite SBT phase formed via intermediate phase Bi₃TaO₇ and a Bi-deficient pyrocholore phase.     

Larger Ba(NO3)2/Sr(NO3)2 crystal growth and solubility determination

The solubility of Ba(NO₃)₂ and Sr(NO₃)₂ crystals in aqueous solution from 25 to 65 °C has been determined by both an optical interferometer and a weight technique. A Mach-Zehnder interferometer was used for measuring the concentration distribution of Ba(NO₃)₂ and Sr(NO₃)₂ near the solid/liquid interface during crystal growth and dissolution. A fringe carrier technique was introduced to visualize more clearly the boundary layer and to solve the concentration distribution. Crystals were successfully grown with sizes larger than  mm by a temperature cooling method. The Ba_xSr_1−x(NO₃)₂ crystal was also nucleated and grown. The Raman spectra of Ba_xSr_1−x(NO₃)₂ indicate that the barium ions probably degrade the properties of Sr(NO₃)₂.     

Preparation,phase structure and microwave dielectric properties of a new low cost MgLi2/3Ti4/3O4 compound

A novel Li-based spinel compound with the composition of MgLi_2/3Ti_4/3O₄ was synthesized by the conventional solid-state reaction method. The phase structure was studied by X-ray diffraction (XRD) technique. When the calcination temperature was over 1050 °C, a single phase compound which has a cubic structure [Fd-3m (227)] with cell parameters of a = 8.4057 Å, V = 593.91 Å³, ρ = 3.51 g cm⁻³ and Z = 8 was obtained. MgLi_2/3Ti_4/3O₄ ceramic could be well densified after sintering above 1125 °C. The microwave dielectric properties were measured using a microwave vector network analyzer in the frequency range of 7–9 GHz MgLi_2/3Ti_4/3O₄ ceramic sintered at 1125 °C for 2 h showed microwave dielectric properties of ?_r = 20.2, Q × f = 62,300 GHz, and τ_f = −27.1 ppm °C⁻¹. Furthermore, 0.95MgLi_2/3Ti_4/3O₄–0.05CaTiO₃ ceramic sintered at 1200 °C for 2 h exhibited good properties of ?_r = 22.6, Q × f = 48,000 GHz, and τ_f = −2.3 ppm °C⁻¹.     

Effect of glass fillers in Cu2ZnNb2O8 ceramics for advanced microwave applications

The effect of glass addition on sintering temperature and microwave dielectric properties of Cu₂ZnNb₂O₈ (CZN) is investigated for possible low temperature co-fired ceramic (LTCC) application. The CZN ceramic was prepared by the solid-state ceramic route. The phase formation, microstructure and elemental composition of the ceramics were studied using X-Ray Diffraction, Scanning Electron Microscopy, Transmission Electron Microscopy and Energy Dispersive Analysis. The CZN sintered at 975 °C/4 h has ?_r = 15.2, tan δ = 0.0007 (at 5.1 GHz) and τ_f of −98 ppm °C⁻¹ and CTE = 1.9 ppm °C⁻¹. The addition of LBS and LMZBS glasses lowered the sintering temperature of CZN to below the melting point of silver. The 1 wt% LBS added CZN sintered at 935 °C/4 h had ?_r = 14.7, tan δ = 0.001 (at 5.1 GHz), τ_f = −19 ppm °C⁻¹ and CTE = −0.6 ppm °C⁻¹. The addition of 0.7 wt% LMZBS to CZN and sintered at 935 °C/4 h had ?_r = 14.8, tan δ = 0.002 (at 5.1 GHz), τ_f = −39 ppm °C⁻¹ and CTE = −0.9 ppm °C⁻¹.     

Calcium-doping for enhanced temperature stability of (Ba0.6Sr0.4)1−xCaxTiO3 thin film dielectric properties

Ternary (Ba_0.6Sr_0.4)_1−xCa_xTiO₃ (BSCT) (x = 0, 0.1, 0.2, 0.3 and 0.4) thin films with thickness of around 500 nm were prepared on Pt(111)/TiO₂/SiO₂/Si substrates by sol-gel methods. BSCT forms the complete solid solutions in a single cubic perovskite structure. The lattice constant, dielectric constant, tanδ and tunability of BSCT decrease, whereas the temperature stability of dielectric properties increases with increasing the Ca concentration. From 25 to 100 °C, the decrease of tunability is about 11% for BSCT with 40 at.% of Ca. BSCT thin films exhibit the comparable tunability, low loss and enhanced temperature stability.