加压喷动流化床煤部分气化数值模型

对加压喷动流化床部分煤气化进行了数值模拟,采用对流动分区法和化学反应速率法进行计算,模型考察了设计参数、运行工况、煤种特性对煤的气化影响,研究了在喷动流化床中压力对煤气化影响,模型计算结果表明,系统压力、反应温度是影响煤部分气化的最关键因素。     

煤质对加压鲁奇炉运行的影响及相应对策

根据义马气化厂Mark-Ⅳ型鲁奇炉近几年的运行情况,以及实际运行过程中采集到的数据,分析了煤的灰分含量、灰熔点、粒度、发热量以及水分含量对气化运行过程的影响,并提出了相应可行的建议,对鲁奇炉的适宜原料和操作条件的选择具有一定的借鉴和指导意义。     

Gas composition and temperature profiles in a spouted bed coal gasifier

Verification of scale-up models of the spouted bed gasifier requires experimental gas composition and temperature profiles within the reactor. Radial and axial profiles are presented for key gaseous species in a 0.30-m. dia, atmospheric pressure gasifier fed at about 30 kg coal/h. Low calorific value gases were generated at air/coal mass ratios of 2.87-4.08, while medium calorific value gases were produced at an oxygen/coal mass ratio of 0.84 and steam/coal ratios of 2.23-2.84. The combustion zone within the gasifier is delineated and the effects of operating conditions on gas composition and temperature profiles are illustrated for typical sub-bituminous and bituminous coals. Recycle of char to the bed from the primary cyclone and bed depth show little effect on profile shape.     

Reasearch on the main factors for changes in pressure based on turbulent circulating fluidized bed coal gasification technology

High temperature preheated air and steam as gasifying agent and coal gasification was performed in a pressurized turbulent circulating fluidized bed (CFB) gasification pilot plant to investigate the pressurized gasification process and estimate its potential. Within the scope of this paper this test facility as well as its operation behavior was described. Furthermore, the parameter pressure has been investigated regarding its influence on the syngas composition and was presented and discussed in the following. The results show that the gasification quality is improved at higher pressure because of the better fluidization in the reactor. Coal gasification at a higher pressure shows advantages in lower heat value and carbon conversion. With the gasifier pressure increased from 0.1MPa to 0.3MPa, the gas heating value is increased by 15%. Increasing the gasifier pressure would increase the carbon conversion from 57.52% to 76.76%. Also, the dry gas yield and efficiency of cold gas increase little with the increase of the gasifier pressure. The operating parameter of pressure exists at optimum operating range for this specific CFB coal gasification process.     

Effects of operating factors in the coal gasification reaction

The effects of operating factors on a gasification system were reviewed by comparing a computational simulation and real operation results. Notable operation conditions include a conveying gas/coal ratio of 0.44, an oxygen/coal ratio of 0.715, a reaction temperature of 1,000 °C, and reaction pressure of 5bar in the case of Adaro coal; based on this, the cold gas efficiency was estimated as 82.19%. At the point of the reaction temperature effect, because the cold gas efficiencies are more than 80% when the reaction temperatures are higher than 900 °C, the gasifier inner temperature must remain over 900 °C. At high reaction temperature such as 1,400 °C, the reaction pressure shows little effect on the cold gas efficiency. The addition of steam into the gasifier causes an endothermic reaction, and then lowers the gasifier outlet temperature. This is regarded as a positive effect that can reduce the capacity of the syngas cooler located immediately after the gasifier. The most significant factor influencing the cold gas efficiency and the gasifier outlet temperature is the O₂/coal ratio. As the O₂/coal ratio is lower, the cold gas efficiency is improved, as long as the gasifier inner temperature remains over 1,000 °C. With respect to the calorific value (based on the lower heating value, LHV) of produced gas per unit volume, as the N₂/coal ratio is increased, the calorific value per syngas unit volume is lowered. Decreasing the amount of nitrogen for transporting coal is thus a useful route to obtain higher calorific syngas. This phenomenon was also confirmed by the operation results.     

粉煤气化炉反应室漏水及应对措施研究

介绍了壳牌粉煤加压气化炉中调和水冷却系统和水汽系统的工艺流程,结合壳牌粉煤加压气化炉的运行经验,分析DCS系统工艺指标变化,判定气化炉漏水的具体部位。从气化炉进料稳定性、炉温过高或过低、锅炉给水水质、烧嘴罩安装等方面分析了泄漏的原因,给出提高氧煤比来提高气化炉反应室炉温,降低系统水/汽系统与气化炉反应室压差减少泄漏量等保生产的应急措施。     

煤气化过程的模型和模拟与优化操作

介绍了煤气化过程的模型和煤气化过程采用机理模型的理由，固定床煤气化过程机理模型的建立以及模拟计算的结果，并探讨了固定床水煤气化炉和流化床水煤气炉制气过程优化操作参数的确定。开发的数学模型已用于制气炉的模拟计算，与实测数据比较符合，由气化过程的数学模拟气化过程不同条件下各种参数的变化规律，进而可得出气化过程的优化操作条件，其确定过程比试验法安全，省时，省料。     

干煤粉加压气化装置控制系统研究

以干煤粉加压气化技术为基础,分析该类型气化装置的运行特点和控制要求,重点讨论气化炉负荷控制和合成气质量控制的关系,提出氧气流量作为气化炉负荷控制主控变量、氧煤比作为合成气质量控制主控变量的控制策略,并制定详细的控制系统设计方案。     

IGCC示范工程煤气化炉的数值模拟

采用Aspen Plus流程模拟软件对某拟建的IGCC示范工程的德士古煤气化炉进行数值模拟,通过考虑碳的不完全转换对计算流程进行了改进,并运用CPD模型预测煤热裂解的产物分布.研究了煤气化炉的重要操作参数(即水煤浆浓度、氧煤比、气化压力和气化温度)对气化结果的影响.在计算区间内,发现高浓度水煤浆浓度范围内,随浓度的增加,煤气的主要成分(H2+CO)的总含量增加.气化温度增大到1400℃左右时,煤气的主要成分随气化温度的进一步增加会趋于一个恒定值.     

Numerical simulation of coal gasification at circulating fluidised bed conditions

This paper presents modelling results for a new pressurised fluidised bed gasifier concept, called the Power High-Temperature Winkler gasifier (PHTW gasifier). The numerical simulation of the steam/oxygen blown and lignite-fuelled power plant gasifier is performed on the 4800 t/day (1000 MW) at a pressure of 33 bar. The formation of flow pattern, turbulence, product gas composition, temperature, and radiation heat transfer were investigated. Influence of diameter variation on the flow patterns at constant operating conditions is presented. A comparison between the calculation and literature data of similar fluidised bed systems shows good conformance. To anticipate the solid's behaviour, particle concentration, particle size change due to pyrolysis and surface reactions, and particle tracks were modelled using an Eulerian–Lagrangian approach. While varying the total particle mass flow, the pressure drop as a function of reactor height was observed.     

恩德炉粉煤气化纯氧制气技术的应用与优化

对恩德炉采用纯氧制气的可行性进行分析,通过纯氧气化试验及物料衡算,分析了恩德炉改为纯氧气化生产半水煤气对合成氨生产的影响。恩德炉采用纯氧气化生产半水煤气的最优操作参数为:操作温度960～990℃,压力10～15 kPa,氧煤比0.44,氧气蒸汽比1.04。对合成氨系统进行了相应的配套改造。改为纯氧气化后,半水煤气中有效气含量增加,合成氨产量增加,经济效益非常可观。     

运用Gibbs自由能最小化方法模拟气流床煤气化炉

基于 Aspen Plus工业系统流程模拟软件 ,运用 Gibbs自由能最小化方法建立了气流床煤气化炉的模型 .研究了气化炉的主要操作参数 (即水煤浆浓度、氧煤比、碳转化率和气化温度 )对气化结果的影响 .对模拟结果进行了分析 ,发现模型基本正确 ,可应用于一些反应机理复杂的气化工艺的化学和热力学平衡计算 .模拟结果表明 ,氧煤比和水煤浆浓度是影响气化炉出口煤气组成的主要因素 ,气化炉温度随着氧煤比的增加而增加 ,也随着水煤浆浓度的增加而增加 .结果还表明 ,氧煤比对气化结果的影响比水煤浆浓度的影响更为显著     

无烟煤在GE水煤浆气化装置的成功应用

对世界上首套以无烟煤为原料的金赤化工GE水煤浆气化装置所使用的原料煤煤质以及运行参数、性能指标进行分析,结果表明,气化炉产能、有效合成气成分、比煤耗、比氧耗等主要性能指标均优于设计值,无烟煤在本装置上的应用非常成功。     

煤粉粒径对HNCERI气化炉碳转化率与固/液渣层分布的影响

以中国华能集团清洁能源技术研究院（Huaneng Clean Energy Research Institute,HNCERI）两段干粉加压气化炉为研究对象,采用考虑了焦炭颗粒表面气体组分扩散效应的随机孔模型计算焦炭气化反应速率以评估碳转化率。同时,耦合熔渣子模型计算气化炉一段壁面固液渣层分布特性和热损失,研究了煤粉粒径对HNCERI气化炉碳转化率和固液渣层分布特性的影响。结果表明所构建的模型可以准确预测气化炉出口主要气体组分组成、碳转化率和气化炉一段壁面热损失;气化炉一段碳转化率受固有气化速率和停留时间控制,二段主要受颗粒停留时间控制;因此,通过减小煤粉粒径可以减小气体在颗粒表面扩散阻力,有利于提高气化炉一段碳转化率,而适量增加煤粉粒径可以增加煤粉颗粒在气化炉二段的停留时间,有利于提高二段碳转化率。模拟结果显示煤粉颗粒粒径从20μm增加到200μm,一段碳转化率从99.68%降低到了95.06%,二段碳转化率从69.03%增加到了89%。煤粉粒径对气化炉上缩口和直段壁面液态渣层分布影响很小,但显著影响固态渣层厚度的发展。     

BGL炉煤气化过程建模和模拟

建立了BGL气化炉的三维非稳态煤气化模型,模型考虑煤炭颗粒的收缩过程,应用收缩核模型集成煤热解模型、气相湍流模型、气固流动模型、气固异相反应模型、气相均相反应模型、能量守恒方程以及相间传热模型等。该模型充分考虑了气化炉内部三维空间的温度和组成分布,通过煤热解段模型化学计量参数优化,得到CO/H₂摩尔比在1.59左右,符合BGL炉热解段运行机制;然后对BGL炉气化段过程进行三维非稳态模拟,模拟出口气组成(CO,H₂,CO₂,CH₄,H₂O,O₂)与文献结果对比,误差均小于4%。证明了BGL模型的准确性。基于该模型,本文对煤气化过程的主要参数进行影响分析。分析结果表明：煤气化效率随汽氧比的增加而提高,当汽氧比确定在1~1.3之间可以满足工艺要求及生产的需要,适合本文研究所用褐煤的特点;氧煤比增加会降低煤气化效率,但合成气中有效气的含量呈现出先增大后减小的趋势,当氧煤比在0.17左右时有效气含量达到峰值;随着煤粒直径的增加,BGL炉内的温度呈降低趋势,最高温度从2536.77 K降到了2047.81 K;同时,煤粒直径增加会减小CO、H₂和CH₄的生成量,并增大CO₂的生成量。     

The comparison study on the operating condition of gasification power plant with various feedstocks

Gasification technology, which converts fossil fuels into either combustible gas or synthesis gas (syngas) for subsequent utilization, offers the potential of both clean power and chemicals. Especially, IGCC is recognized as next power generation technology which can replace conventional coal power plants in the near future. It produces not only power but also chemical energy sources such as H₂, DME and other chemicals with simultaneous reduction of CO₂. This study is focused on the determination of operating conditions for a 300 MW scale IGCC plant with various feedstocks through ASPEN plus simulator. The input materials of gasification are chosen as 4 representative cases of pulverized dry coal (Illinois#6), coal water slurry, bunker-C and naphtha. The gasifier model reflects on the reactivity among the components of syngas in the gasification process through the comparison of syngas composition from a real gasifier. For evaluating the performance of a gasification plant from developed models, simulation results were compared with a real commercial plant through approximation of relative error between real operating data and simulation results. The results were then checked for operating characteristics of each unit process such as gasification, ash removal, acid gas (CO₂, H₂S) removal and power islands. To evaluate the performance of the developed model, evaluated parameters are chosen as cold gas efficiency and carbon conversion for the gasifier, power output and efficiency of combined cycle. According to simulation results, pulverized dry coal which has 40.93% of plant net efficiency has relatively superiority over the other cases such as 33.45% of coal water slurry, 35.43% of bunker-C and 30.81% of naphtha for generating power in the range of equivalent 300 MW.     

Identification of reaction zones in a commercial Sasol-Lurgi fixed bed dry bottom gasifier operating on North Dakota lignite

The Sasol-Lurgi fixed bed dry bottom gasification technology has the biggest market share in the world with 101 gasifiers in operation. To be able to further improve the technology and also to optimise the operating plants, it is important that the fundamentals of the process are understood. The main objective of this study was to determine the reaction zones occurring in the Sasol-Lurgi fixed bed dry bottom (S-L FBDB) gasifier operating on North Dakota lignite. A Turn-Out sampling method and subsequent chemical analyses of the gasifier fuel bed samples was used to determine the reaction zones occurring in the commercial MK IV, S-L FBDB gasifier operating on North Dakota lignite. The reaction zones were further compared with the same reactor operating on bituminous coal.Based on the results obtained from this study it was found that about two thirds of the gasifier volume was used for drying and de-volatilising the lignite thus leaving only about a third of the reactor volume for gasification and combustion. Nonetheless, due to the high reactivity of the lignite, the char was consumed within a third of the remaining gasifier volume. Clear overlaps between the reaction zones were observed in the gasifiers thus confirming the gradual transition from one reaction zone to another as reported in literature. Due to the high moisture content in the lignite, the pyrolysis zone in the gasifiers operating on North Dakota lignite occurred lower/deeper in the gasifier fuel bed as compared to the same gasifier operating on South African bituminous coal from the Highveld coalfield. All the other reaction zones in the gasifier operating on bituminous coal were also higher in the bed compared to the lignite operation. This can therefore explain the higher gas outlet temperatures for the S-L FBDB gasifiers operating on higher rank coals when compared to the gasifiers operating on lignite. The fact that the entire reactor volume was utilized for drying, de-volatilisation, gasification and combustion with carbon conversion of >98% makes the S-L FBDB gasifier very suitable for lignite gasification.     

4.0MPa碎煤加压气化炉加煤系统的技术改造

分析了以劣质褐煤为原料的4.0 MPa碎煤加压气化炉加煤系统生产中存在的问题,指出加煤系统循环时间长是影响气化炉加煤量、制约生产负荷的主要原因。在现有装置上进行改造,采用降低管线阻力的方法,可使加煤时间由原来的1 189 s¹ 323 s缩短为725 s1 323 s缩短为725 s⁸59 s,满足了气化炉110%负荷运行的要求。     

水煤浆加压气化技术改造小结

自1994年3月10日德士古水煤浆加压气化装置通过生产考核以来，根据实际情况对不适应系统稳定生产的文氏洗涤器，气化炉上升管支撑，闪蒸系统管道及气化炉渣口予以改造，并对气化炉耐火材料，气化炉烧嘴和高，低压煤浆泵实施了国产化措施，取得显著成效，标志着我厂驾驶水煤浆加压气化装置的能力已达到了较高水平。     

水冷壁气化炉内熔渣流动特性模型

通过将3D气化炉模型、熔渣一维流动传热模型和颗粒壁面捕捉模型耦合,对工业水煤浆水冷壁气化炉内的熔渣流动特性进行模型研究。重点分析了颗粒壁面行为对气化炉结渣的影响以及氧煤比变化对于渣层厚度的影响,并简要分析了水冷壁气化炉和耐火砖气化炉的差异。研究结果表明:大粒径颗粒易于被壁面捕捉,利于穹顶和直筒段渣层的形成,但不利于碳转化率的提高;小粒径颗粒具有高碳转化率,是下游细灰的主要来源,容易加剧下游受热面和灰黑水系统的负担;水冷壁气化炉内形成的固态渣层是气化炉热阻的主要组成部分,能够起到"以渣抗渣"的作用。