A novel titania nanorods‐filled composite solid electrolyte with improved room temperature performance for solid‐state Li‐ion battery

Solid‐state batteries (SSBs) with room temperature (RT) performances had been one of the most promising technologies for energy storage. To achieve a chemical stable and high ionic conductive solid electrolyte, herein, a titania (TiO₂) (B) nanorods‐filled poly(propylene carbonate) (PPC)‐based organic/inorganic composite solid electrolyte (CSE) was prepared for the first time. It was found that by using TiO₂(B) nanorods, the ionic conductivity of the CSE membrane could be improved to 1.52 × 10^?4 S/cm, the electrochemical stable window was more than 4.6 V, and the tensile strength reaches 27 MPa with a strain less than 6%. The CSE was applied for SSB and showed excellent room temperature electrochemical performances. At 25°C, the LiFePO₄/CSE/Li SSB with 3%TiO₂‐filled CSE had the first cycle specific discharge capacity of 162 mAh/g with a capacity retention of 93% after 100 cycles at 0.3C. While the NCM622/CSE/Li SSB with 3%TiO₂‐filled CSE had the first specific discharge capacity of 165 mAh/g with a capacity retention of 88% after 100 cycles at 0.3C. The enhancement effect of TiO₂(B) nanorods could be ascribed that the rod‐like fillers provide more continuous Li‐ion transport path compared with nano particles, and the surface porosity and composition of TiO₂(B) nanorods could also improve the interfacial contact and Lewis acid‐base reaction sites between polymer and fillers. The TiO₂(B) nanorods‐filled CSE with high chemical stability, potential window, and ionic conductivity was promising to meet the requirements of SSBs.     

Simultaneously enhancing the thermal stability and electrochemical performance of solid polymer electrolytes by incorporating rod-like Zn2(OH)BO3 particles

Solid polymer electrolytes provide high safety and good electrochemical stability in solid-state lithium batteries (SSLBs) compared with conventional liquid electrolytes. In this work, a novel solid polymer composite electrolyte based on poly (ethylene oxide) (PEO) filled with rod-like Zn₂(OH)BO₃ particles was prepared by a grinding process followed with a heating treatment process and a cold pressing process. The effect of the incorporation amount of rod-like Zn₂(OH)BO₃ particles on the ionic conductivity was investigated systemically. It is found that 10 mol% of rod-like Zn₂(OH)BO₃ particles addition resulted in a highest ionic conductivity of 2.78 × 10⁻⁵ at 30 °C and the improved ionic conductivity was considered to be caused by the reducing of PEO crystallinity and the increasing of Li ion migrating pathway on the interface between the Zn₂(OH)BO₃ and PEO. In addition, the optimum composite electrolyte exhibited a high electrochemical stability window of 4.51 V (vs. Li/Li⁺), good lithium stability and excellent thermal stability.     

Toward high performance solid-state lithium-ion battery with a promising PEO/PPC blend solid polymer electrolyte

A promising solid polymer blend electrolyte is prepared by blending of poly(ethylene oxide) (PEO) with different content of amorphous poly(propylene carbonate) (PPC), in which the amorphous property of PPC is utilized to enhance the amorphous/free phase of solid polymer electrolyte, so as to achieve the purpose of modifying PEO-based solid polymer electrolyte. It indicates that the blending of PEO with PPC can effectively reduce the crystallization and increase the ion conductivity and electrochemical stability window of solid polymer electrolyte. When the content of PPC reaches 50%, the ionic conductivity reaches the maximum, which is 2.04 × 10⁻⁵ S cm⁻¹ and 2.82 × 10⁻⁴ S cm⁻¹ at 25°C and 60°C, respectively. The electrochemical stability window increases from 4.25 to 4.9 V and the interfacial stability of lithium metal anode is also greatly improved. The solid-state LiFePO₄//Li battery with the PEO/50%PPC blend solid polymer electrolyte has good cycling stability, which the maximum discharge specific capacity is up to 125 mAh g⁻¹ at a charge/discharge current density of 0.5 C at 60°C.     

Electrochemical properties and performance of poly(acrylonitrile)-based polymer electrolyte for Li/LiCoO2 cells

It has been demonstrated that LiCoO₂ is a very attractive cathode active material for lithium rechargeable cells. Poly(acrylonitrile) (PAN)-based polymer electrolyte is used for Li/LiCoO₂ cells. PAN-based polymer electrolyte shows ionic conductivity of the order 1 mS cm⁻¹ at room temperature, irrespective of time evolution, and wide electrochemical stability up to 4.3 V (versus Li⁺/Li). An LiCoO₂ composite cathode containing 4 wt.% conductive material displays a good cycling performance. From a.c. impedance results, the interfacial resistance of Li/LiCoO₂ cells is dominated by the passive layer formed at the lithium/polymer electrolyte interface.     

Ionic liquid doped PEO-based solid polymer electrolytes for lithium-ion polymer batteries

The influence of adding the room-temperature ionic liquid 1-ethyl-3-methyllimidazolium bis(trifluoromethylsulfonyl)imide (EMImTFSI) to poly(ethylene oxide) (PEO)–lithium difluoro(oxalato)borate (LiDFOB) solid polymer electrolyte and the use of these electrolytes in solid-state Li/LiFePO₄ batteries has been investigated. Different structural, thermal, electrical and electrochemical studies exhibit promising characteristics of these polymer electrolyte membranes, suitable as electrolytes in rechargeable lithium-ion batteries. The crystallinity decreased significantly due to the incorporation of ionic liquid, investigated by X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The ion–polymer interaction, particularly the interaction of cations in LiDFOB and ionic liquid with ether oxygen atom of PEO chains, has been evidenced by FT-IR studies. The polymer electrolyte with ～40 wt% of ionic liquid offers a maximum ionic conductivity of ～1.85 × 10^?4 S/cm at 30 °C with improved electrochemical stabilities. The Li/PEO-LiDFOB-40 wt% EMImTFSI/LiFePO₄ coin-typed cell cycled at 0.1 C shows the 1st discharge capacity about 155 mAh g^?1, and remains 134.2 mAh g^?1 on the 50th cycle. The addition of the ionic liquid to PEO₂₀-LiDFOB polymer electrolyte has resulted in a very promising improvement in performance of the lithium polymer batteries.     

A novel organic/inorganic composite solid electrolyte with functionalized layers for improved room‐temperature rate performance of solid‐state lithium battery

High ionic conductivity at room temperature (RT) and good ion transport capability at electrode/electrolyte interface are fundamental requirements for high‐rate solid‐state lithium batteries (SSBs). In this work, we designed a poly (propylene carbonate) (PPC)‐based organic/inorganic composite solid electrolyte (CSE) membrane with high filling of tantalum‐doped lithium lanthanum zirconium oxide (LLZTO) and functionalized layers for enhancing the RT rate performance of SSB. The synergistic effect of LLZTO and interfacial functionalized layers endows the NCM622/CSE/Li battery with high‐rate and cycling performances at RT. The SSB with 20% LLZTO‐filled solid electrolyte shows the initial capacities of 162.0, 148.5 and 130.1 mAh g^?1 at 1C, 2C, and 3C respectively, with retention capacities of 115.6, 104, and 100.6 mAh g^?1 after 150 cycles. This strategy for an organic/inorganic CSE is of great practical significance for the development of high‐rate SSBs.     

Fabrication and characteristics of a composite cathode of sulfonated polyaniline and Ramsdellite–MnO2 for a new rechargeable lithium polymer battery

The ionic conductivity of a polyacrylonitrile (PAN)-based solid polymer electrolyte is 1.4×10⁻³ S cm⁻¹, which is sufficient for the electrolyte to be used in a rechargeable lithium polymer battery. The anodic stability of the solid polymer electrolyte is over 4.6 V (vs. Li/Li⁺). A reduced, highly sulfonated form of polyaniline (SPAn) and Ramsdellite–MnO₂ (R-MnO₂) are synthesized and used as a cathodic material for a rechargeable lithium polymer battery. Three kinds of cathodes are prepared from SPAn, R-MnO₂, and a mixture of SPAn and R-MnO₂. The electrochemical properties and diffusion coefficient of lithium ions in each cathode, and the interface between the solid polymer electrolyte and each cathode are investigated by cyclic voltammetry and impedance spectroscopy. The redox processes of the SPAn cathode are two-step reactions. The cathodic and anodic peak currents increase as the cycle number increases. In the redox processes of the R-MnO₂ cathode, the cathodic peak current on the second cycle is 62% of that on the first cycle. The Li/R-MnO₂ battery has a very high initial discharge capacity, but very poor cycleability. For the composite cathode, the cathodic peak current on the second cycle is 72% of that on the first cycle, i.e., higher than that for the R-MnO₂ cathode. The diffusion coefficient of the composite cathode during the discharge process is close to the sum of each variation in the SPAn and R-MnO₂ cathodes. The instability of the R-MnO₂ cathode at x=0.3 and x=0.2 during the charge process is not observed with the composite cathode. The discharge–charge performance of three types of battery are investigated. The initial discharge capacity of the Li/composite cathode battery is 97.0 m Ah g⁻¹. This battery has higher discharge capacity than the Li/SPAn battery (66.8 m Ah g⁻¹), and better cycleability than the Li/R-MnO₂ battery.     

High‐performance solid PEO/PPC/LLTO‐nanowires polymer composite electrolyte for solid‐state lithium battery

Solid polymer composite electrolyte (SPCE) with good safety, easy processability, and high ionic conductivity was a promising solution to achieve the development of advanced solid‐state lithium battery. Herein, through electrospinning and subsequent calcination, the Li_0.33La_0.557TiO₃ nanowires (LLTO‐NWs) with high ionic conductivity were synthesized. They were utilized to prepare polymer composite electrolytes which were composed of poly (ethylene oxide) (PEO), poly (propylene carbonate) (PPC), lithium bis (fluorosulfonyl)imide (LiTFSI), and LLTO‐NWs. Their structures, thermal properties, ionic conductivities, ion transference number, electrochemical stability window, as well as their compatibility with lithium metal, were studied. The results displayed that the maximum ionic conductivities of SPCE containing 8 wt.% LLTO‐NWs were 5.66 × 10^?5 S cm^?1 and 4.72 × 10^?4 S cm^?1 at room temperature and 60°C, respectively. The solid‐state LiFePO₄/Li cells assembled with this novel SPCE exhibited an initial reversible discharge capacity of 135 mAh g^?1 and good cycling stability at a charge/discharge current density of 0.5 C at 60°C.     

Development of PVA based micro-porous polymer electrolyte by a novel preferential polymer dissolution process

A micro-porous polymer electrolyte based on PVA was obtained from PVA–PVC based polymer blend film by a novel preferential polymer dissolution technique. The ionic conductivity of micro-porous polymer electrolyte increases with increase in the removal of PVC content. Finally, the effect of variation of lithium salt concentration is studied for micro-porous polymer electrolyte of high ionic conductivity composition. The ionic conductivity of the micro-porous polymer electrolyte is measured in the temperature range of 301–351 K. It is observed that a 2 M LiClO₄ solution of micro-porous polymer electrolyte has high ionic conductivity of 1.5055 × 10⁻³ S cm⁻¹ at ambient temperature. Complexation and surface morphology of the micro-porous polymer electrolytes are studied by X-ray diffraction and SEM analysis. TG/DTA analysis informs that the micro-porous polymer electrolyte is thermally stable upto 277.9 °C. Chronoamperommetry and linear sweep voltammetry studies were made to find out lithium transference number and stability of micro-porous polymer electrolyte membrane, respectively. Cyclic voltammetry study was performed for carbon/micro-porous polymer electrolyte/LiMn₂O₄ cell to reveal the compatibility and electrochemical stability between electrode materials.     

Enhanced electrochemical properties of PEO-based composite polymer electrolyte with shape-selective molecular sieves

ZSM-5 molecular sieves, usually known as shape-selective catalyst in a great deal of catalysis fields, due to its special pore size and two-dimensional interconnect channels. In this work, a novel PEO-based composite polymer electrolyte by using ZSM-5 as the filler has been developed. The interactions between ZSM-5 and PEO matrix are studied by DSC and SEM techniques. The effects of ZSM-5 on the electrochemical properties of the PEO-based electrolyte, such as ionic conductivity, lithium ion transference number, and interfacial stability with lithium electrode are studied by electrochemical impedance spectroscopy and steady-state current method. The experiment results show that ZSM-5 can enhance the ionic conductivity and increase the lithium ion transference number of PEO-based electrolyte more effectively comparing with traditional ceramic fillers such as SiO₂ and Al₂O₃, resulting from its special framework topology structure. The excellent performances such as high ionic conductivity, good compatibility with lithium metal electrode, and broad electrochemical stability window suggesting that PEO–LiClO₄/ZSM-5 composite polymer electrolyte can be used as candidate electrolyte materials for lithium polymer batteries.     

Improved performance of Li hybrid solid polymer electrolyte cells

The seminal research by Wright et al. on polyethylene oxide (PEO) solid polymer electrolyte (SPE) generated intense interest in all solid-state rechargeable lithium batteries. Following this a number of researchers have studied the physical, electrical and transport properties of thin film PEO electrolyte containing Li salt. These studies have clearly identified the limitations of the PEO electrolyte. Chief among the limitations are a low cation transport number (t₊), high crystallinity and segmental motion of the polymer chain, which carries the cation through the bulk electrolyte. While low t₊ leads to cell polarization and increase in cell resistance high T_g reduces conductivity at and around room temperatures. For example, the conductivity of PEO electrolyte containing lithium salt is <10⁻⁷ S cm⁻¹ at room temperature. Although modified PEO electrolytes with lower T_g exhibited higher conductivity (∼10⁻⁵ S cm⁻¹ at RT) the t₊ is still very low ∼0.25 for lithium ion. Numerous other attempts to improving t₊ have met with limited success. The latest approach involves integrating nano domains of inorganic moieties, such as silcate, alumosilicate, etc. within the polymer component. This approach yields an inorganic–organic component (OIC) based polymer electrolyte with higher conductivity and t₊ for Li⁺_. This paper describes the improved electrical and electrochemical properties of OIC-based polymer electrolyte and cells containing Li anode with either a TiS₂ cathode or Mag-10 carbon electrode. Several solid polymer electrolytes derived from silicate OIC and salt-in-polymer constituent based on Li triflate (LiTf) and PEO are studied. A typical composition of the SPE investigated in this work consists of 600 kDa PEO, lithium triflate (LiTf, LiSO₃CF₃) and 55% of silicate based on (3-glycidoxypropyl)trimethoxysilane and tetramethoxysilane at molar ratio 4:1 and 0.65 mol% of aluminum(tri-sec-butoxide) (GTMOS-Al1-900k-55%). Several pouch cells consisting of Li/OIC-based–SPE/cathode containing OIC-based–SPE–LiTf binder were fabricated and tested, these cells are called modified cells. The charge/discharge and impedance characteristics of the new cells (also called modified cells) are compared with that of the pouch cells containing the conventional PEO–LiTf electrolyte as the cathode binder, these cells are called non-modified cells. The new cells can be charged and discharged at 70 °C at higher currents. However, the old cells can be charged and discharged only at 80 °C or above and at lower currents. The cell impedance for the new cells is much lower than that for the old cells.     

新型PEO/LPOS复合聚合物电解质的制备与性能研究

将具有较高电导率和稳定性的硫化物电解质LPOS引入PEO基聚合物中,制备一种新型PEO/LPOS复合聚合物电解质。研究结果表明,1%LPOS的添加能显著改善PEO基聚合物电解质的电导率、锂离子迁移数和电化学稳定性。与纯PEO基电解质相比,新制备的复合聚合物电解质PEO18-LiTFSI-1%LPOS室温电导率由   6.18×106 S/cm提高至1.60×105 S/cm,提高了158%。80 ℃表现出最佳电导率为1.08×103 S/cm,电化学窗口提高至4.7 V,同时具有非常良好的对锂稳定性。以新型复合电解质组装的LiFePO4/Li全固态锂电池表现出良好的循环稳定性,在60 ℃ 1 C下循环50周后放电比容量仍维持在105 mA•h/g以上。     

Ionanofluid plasticized electrolyte with improved electrical and electrochemical properties for high-performance lithium polymer battery

Herein, the electrochemical characteristics of Li/LiFePO₄ battery, comprising a new class of poly (ethylene oxide) (PEO) hosted polymer electrolytes, are reported. The electrolytes were prepared using lithium bis(trifluoromethylsulfonyl)imide (LiTFSI) dopant salt and imidazolium ionic liquid-based nanofluid (ionanofluid) as the plasticizer. Morphological, thermophysical, electrical, and electrochemical properties of these newly developed electrolytes were studied. Using FT-IR spectroscopy, the interactions between dopant salt plasticizers and the host polymer, within the electrolytes, were evaluated. The optimized 30 wt% ionanofluid plasticized electrolyte exhibits a room temperature ionic conductivity of 6.33 × 10⁻³ S cm⁻¹, wide electrochemical voltage window (~4.94 V vs Li/Li⁺) along with a moderately high value of lithium-ion transference number (0.47). The values are substantially higher than that of similar wt% IL plasticized electrolyte (7.85 × 10⁻⁴ S cm⁻¹, ~4.44 V vs Li/Li⁺ and ~ 0.28, respectively). Finally, the Li/LiFePO₄ battery, comprising optimized 30 wt% ionanofluid plasticized electrolyte, delivers 156 mAh g⁻¹ discharge capacity at 0.1 C rate and able to retain its 92% value after 50 cycles. Such a superior battery performance as compared to the IL plasticized electrolyte cell (137 mAh g⁻¹ and 84% after 50 cycles at the same current rate) would endow this ionanofluid a very promising plasticizer to develop electrolytes for next-generation lithium polymer battery.     

Boosting the performance of poly(ethylene oxide)-based solid polymer electrolytes by blending with poly(vinylidene fluoride-co-hexafluoropropylene) for solid-state lithium-ion batteries

To seek a solid polymer electrolyte (SPE) with excellent performance, a novel poly(ethylene oxide) (PEO) based SPE is prepared by blending an appropriate amount of microcrystalline poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) with PEO using a universal solution casting method. Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD) and differential scanning calorimetry (DSC) are utilized to analyse the samples. The crystallinity of the blend solid polymer electrolyte is significantly lower than that of the neat PEO-based SPE. The addition of the PVDF-HFP disrupts the segment structure of the PEO crystal region and increases the proportion of the amorphous region, thus boosting the migration of lithium ions. The results show that the electrochemical stability window of the blend solid polymer electrolyte reaches as high as 4.8 V. The initial discharge specific capacity of the solid-state LiFePO₄/SPE/Li battery is 131 mAh g⁻¹ at 0.5 C and 60°C, and the discharge specific capacity is still 110.5 mAh g⁻¹ after 100 cycles. On the basis of the results, the novel SPE has a widespread application prospects in solid-state lithium-ion batteries.     

Effects of addition of TiO2 nanoparticles on mechanical properties and ionic conductivity of solvent-free polymer electrolytes based on porous P(VdF-HFP)/P(EO-EC) membranes

To enhance the performance (i.e., mechanical properties and ionic conductivity) of pore-filling polymer electrolytes, titanium dioxide (TiO₂) nanoparticles are added to both a porous membrane and its included viscous electrolyte, poly(ethylene oxide-co-ethylene carbonate) copolymer (P(EO-EC)). A porous membrane with 10 wt.% TiO₂ shows better performance (e.g., homogeneous distribution, high uptake, and good mechanical properties) than the others studied and is therefore chosen as the matrix to prepare polymer electrolytes. A maximum conductivity of 5.1 × 10⁻⁵ S cm⁻¹ at 25 °C is obtained for a polymer electrolyte containing 1.5 wt.% TiO₂ in a viscous electrolyte, compared with 3.2 × 10⁻⁵ S cm⁻¹ for a polymer electrolyte without TiO₂. The glass transition temperature, T_g is lowered by the addition of TiO₂ (up to 1.5 wt.% in a viscous electrolyte) due to interaction between P(EO-EC) and TiO₂, which weakens the interaction between oxide groups of the P(EO-EC) and lithium cations. The overall results indicate that the sample prepared with 10 wt.% TiO₂ for a porous membrane and 1.5 wt.% TiO₂ for a viscous electrolyte is a promising polymer electrolyte for rechargeable lithium batteries.     

Photocured PEO-based solid polymer electrolyte and its application to lithium–polymer batteries

A solid polymer electrolyte (SPE) based on polyethylene oxide (PEO) is prepared by photocuring of polyethylene glycol acrylates. The conductivity is greatly enhanced by adding low molecular weight poly(ethylene glycol) dimethylether (PEGDME). The maximum conducticity is 5.1×10⁻⁴ S cm⁻¹ at 30°C. These electrolytes display oxidation stability up to 4.5 V against a lithium reference electrode. Reversible electrochemical plating/stripping of lithium is observed on a stainless steel electrode. Li/SPE/LiMn₂O₄ as well as C(Li)/SPE/LiCoO₂ cells have been fabricated and tested to demonstrate the applicability of the resulting polymer electrolytes in lithium–polymer batteries.     

Study of multiple interactions in mesoporous composite PEO electrolytes

This paper discusses the FT-infrared (IR) and NMR spectroscopy results of a mesoporous silica (SBA-15) composite poly(ethylene oxide) (PEO) solid lithium polymer electrolyte. The changes in COC, CH, and ClO₄ stretching IR vibrational modes indicated a combination of multiple interactions through Lewis acid–base reactions which interrupt the PEO crystalline structure. Higher salt disassociation by SBA-15 is also apparent from ClO₄ vibrational band mode.NMR studies indicated three types of Li ion environments; the first one is Li ions within the conventional amorphous PEO, the second is Li ions on the surface of mesoporous SBA-15 and the third is Li ions trapped along with PEO in the nano-tubular channels of SBA-15. Annealing leads to interaction of more PEO and lithium ions with the SBA-15 and free ions for conduction, as reflected in the ⁷Li variable temperature (VT)-NMR measurements and variable temperature ion conductivity.     

Electrochemical properties of cross-linked polymer electrolyte by electron beam irradiation and application to lithium ion batteries

A polymer electrolyte was successfully fabricated for a room temperature operation lithium battery by cross-linking the mixture of oligomeric poly (ethylene glycol) dimethylether (PEGDME) and poly (ethylene glycol) diacrylate (PEGDA) with Li(CF₃SO₂)₂N using electron beam irradiation. The maximum ionic conductivity achieved for the cross-linked solid polymer electrolyte (c-SPE) at room temperature was 2.1 × 10⁻⁴ S cm⁻¹ and the lithium transport number of the electrolyte was around 0.2. The c-SPE showed no reaction heat with lithium metal up to 300 °C. The interface resistance of Li/c-SPE/Li at room temperature was about 45 Ω cm², which is considerable lower than that of 210 Ω cm² for Li/PEO₁₀Li(CF₃SO₂)₂N/Li. The electrochemical window of the polymer electrolyte was above 4 V (versus Li⁺/Li). The initial discharge capacity for the Li/SPE/LiFePO₄-C cell was approximately 90 mAh g⁻¹ for LiFePO₄-C at 1/10 °C rate at room temperature and showed a good cyclability and a high coulombic efficiency of 99.2%.     

Rechargeable lithium battery employing a new ambient temperature hybrid polymer electrolyte based on PVK+PVdF–HFP (copolymer)

We describe here for the first time, our recent success in developing an ambient temperature Li⁺ conducting solid polymer electrolyte (SPE) using the concept of polymer alloying upon blending two thermoplastic polymers such as poly(vinylidene) fluoride-hexafluoropropylene (PVdF–HFP-copolymer) and poly(N-vinylcarbazole), PVK and achieved the room temperature electrolytic conductivity (σ_i) of 0.7×10⁻³ S/cm for a typical composition of PVdF–HFP copolymer/PVK blend mixed with EC/LiBF₄ molar composition. The ionic transference number of 0.49 was deduced from combined ac-impedance and dc polarization method. High-resolution optical microscopic examination revealed the disappearance of characteristic highly porous surface structure of PVdF–HFP matrix upon blending with PVK leading to the formation of resultant PVdF–HFP/PVK blend polymer alloy. The electrochemical stability of the polymer electrolyte membrane thus obtained was found to be stable up to ∼4.7 V versus Li/Li⁺. The new hybrid alloy polymer electrolyte membrane was found to exhibit good interfacial properties against lithium metal and thus, it was found to aid the room temperature operation as electrolytic membrane cum separator in all-solid state rechargeable lithium polymer test cell, LiCo_0.8Ni_0.2O₂/SPE/Li.     

Unveiling the roles of alumina as a sintering aid in Li-Garnet solid electrolyte

The superiority of garnet-type solid electrolyte makes it one of most promising candidates for all-solid-state lithium batteries. Several studies show that introduction of alumina during synthesis can greatly improve the density and ionic conductivity of garnet electrolyte Li₇La₃Zr₂O₁₂ (LLZO), but the reason of poor sinterability of LLZO is still unclear. In this study, we reveal that lithium carbonate, which has a high decomposition temperature and covers on the particle surface of LLZO, is the underlying reason that handicaps the sinterability of Li-Garnet electrolyte in air. The addition of alumina promotes the decomposition of Li₂CO₃ (down to 400°C) and the concomitant product LiAlO₂, as a fast Li-ion conductor, facilitates the sintering process and bulids a fast Li-ion conducting network along the grain-boundaries, significantly increasing the ionic conductivity of Li-Garnet electrolyte. By the conventional solid state sintering, the 10 mol% Al₂O₃ modified Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZT-10Al₂O₃) electrolyte reaches a relative density of 96% and shows a conductivity of 0.31 mS cm⁻¹ at room temperature. The prepared LLZT-10Al₂O₃ electrolyte exhibits a good wetting property toward metallic Li electrode with an interfacial resistance of 59 Ω cm² compared to 1270 Ω cm² for LLZT/Li. This work provides a fundamental understanding and a valuable strategy for developing high performance garnet-type electrolyte for all-solid-state lithium batteries.