Application of NOX storage/release materials based on alkali-earth oxides supported on Al2O3 for high-temperature diesel soot oxidation

Alkali-earth oxides and nitrates supported on alumina were studied as model systems for NO_X storage/release. Their impact on the high-temperature soot oxidation has been investigated. The stability of surface nitrates and temperature of NO_X release increase parallel to the basicity of the cation. The presence of soot decreases the temperature of NO_X release. The storage capacity depends on the several factors, such as basicity, dispersion of the cation, and pre-treating conditions. Adsorption of NO with O₂ at 200 °C leads to the formation of surface nitrates that mainly exist as ionic nitrates. Stored nitrates contribute to the soot oxidation and assist to lower the temperature of soot oxidation up to almost 100 °C. In the presence of only NO_X storage material the efficiency of NO_X utilization is, however, quite low, around 30%. Therefore, the presence of an oxidation catalyst is essential to increase the efficiency of NO_X utilization for soot oxidation up to 140% and selectivity towards CO₂. A combination of oxidation catalyst with NO_X storage materials enables to lower the temperature of soot oxidation more than 100 °C for the Sr- and Ca-based systems.     

Cu/Al2O3 catalysts for soot oxidation: Copper loading effect

Cu/Al₂O₃ catalysts with metal loading from 0.64 to 8.8 wt.% have been prepared and characterized by different techniques: N₂ adsorption at −196 °C (BET surface area), ICP (Cu loading), XRD, selective copper surface oxidation with N₂O (Cu dispersion), TPR-H₂ (redox properties), and XPS (copper surface species). The catalytic activity for soot oxidation has been tested both in air and NO_x/O₂. The activity in air depends on the amount of easily-reduced Cu(II) species, which are reduced around 275 °C under TPR-H₂ conditions. The amount of the most active Cu(II) species increases with the copper loading from Cu_1% to Cu_5% and remains almost constant for higher copper loading. In the presence of NO_x, the first step of the mechanism is NO oxidation to NO₂, and the catalytic activity for this reaction depends on the copper loading. For catalysts with copper loading between Cu_1% and Cu_5%, the catalytic activity for soot oxidation in the presence of NO_x depends on NO₂ formation. For catalysts with higher copper loading this trend is not followed because of the low reactivity of model soot at the temperature of maximum NO₂ production. Regardless the copper loading, all the catalysts improve the selectivity towards CO₂ formation as soot oxidation product both under air and NO_x/O₂.     

Synergistic catalysis of carbon black oxidation by Pt with MoO3 or V2O5

A series of SiO₂-supported MoO₃, V₂O₅, and Pt catalysts were prepared for the study of model soot oxidation with simulated diesel exhaust gas. Composite samples of Pt with the metal oxides demonstrated higher oxidation activities than the single-component SiO₂-supported MoO₃, V₂O₅ or Pt catalysts in the absence of SO₂ in the reactant gas. Based on the effects of NO₂ on carbon oxidation, a synergistic reaction mechanism was suggested to explain the effects of combining Pt with the oxides: Pt catalyzes the oxidation of NO with gas phase O₂ to NO₂, while MoO₃ and V₂O₅ catalyze the oxidation of carbon with NO₂. Finally, the effects of SO₂ on the carbon oxidation reaction were examined and discussed.     

CoAl2O4 spinel catalyst for soot combustion with NOx/O2

Mesoporous and nanosized cobalt aluminate spinel with high specific surface area was prepared using microwave assisted glycothermal method and used as soot combustion catalyst in a NO_x + O₂ stream. For comparison, zinc aluminate spinel and alumina supported platinum catalysts were prepared and tested. All samples were characterised using XRD, (HR)TEM, N₂ adsorption–desorption measurements. The CoAl₂O₄ spinel was able to oxidise soot as fast as the reference Pt/Al₂O₃ catalyst. Its catalytic activity can be attributed to a high NO_x chemisorption on the surface of this spinel, which leads to the fast oxidation of NO to NO₂.     

Influence of low concentration of SO2 for selective reduction of NO by C3H8 in lean-exhaust conditions on the activity of Ag/Al2O3 catalyst

The effect of SO₂ for the selective reduction of NO by C₃H₈ on Ag/Al₂O₃ was investigated in the presence of excess oxygen and water vapor. The NO_x conversion decreased permanently even in the presence of a low concentration of SO₂ (0.5–10 ppm) at <773 K. The increase in SO₂ concentration resulted in a large decrease in NO_x conversion at 773 K. However, when the reaction temperature was more than 823 K, the activity of Ag/Al₂O₃ remained constant even in the presence of 10 ppm of SO₂. The sulfate species formed on the used Ag/Al₂O₃ were characterized by a temperature programmed desorption method. The sulfated species formed on silver should mainly decrease the deNO_x activity on the Ag/Al₂O₃. The sulfated Ag/Al₂O₃ was appreciably regenerated by thermal treatment in the deNO_x feed at 873 K. The moderate activity remains at 773 K in the presence of 1 ppm SO₂ for long time by the heat treatment at every 20 h intervals.     

Investigation of flue-gas treatment with O3 injection using NO and NO2 planar laser-induced fluorescence

Direct ozone (O₃) injection is a promising flue-gas treatment technology based on oxidation of NO and Hg into soluble species like NO₂, NO₃, N₂O₅, oxidized mercury, etc. These product gases are then effectively removed from the flue gases with the wet flue gas desulfurization system for SO₂. The kinetics and mixing behaviors of the oxidation process are important phenomena in development of practical applications. In this work, planar laser-induced fluorescence (PLIF) of NO and NO₂ was utilized to investigate the reaction structures between a turbulent O₃ jet (dry air with 2000 ppm O₃) and a laminar co-flow of simulated flue gas (containing 200 ppm NO), prepared in co-axial tubes. The shape of the reaction zone and the NO conversion rate along with the downstream length were determined from the NO-PLIF measurements. About 62% of NO was oxidized at 15d (d, jet orifice diameter) by a 30 m/s O₃ jet with an influence width of about 6d in radius. The NO₂ PLIF results support the conclusions deduced from the NO-PLIF measurements.     

NOx adsorption and diesel soot combustion over La2O3 supported catalysts containing K, Rh and Pt

In this work we report results of NOx adsorption and diesel soot combustion on a noble metal promoted K/La₂O₃ catalyst. The fresh-unpromoted solid is a complex mixture of hydroxide and carbonate compounds, but the addition of Rh favors the preferential formation of lanthanum oxycarbonate during the calcination step. K/La₂O₃ adsorbs NOx through the formation of La and K nitrate species when the solid is treated in NO + O₂ between 70 and 490 °C. Nitrates are stable in the same temperature range under helium flow. However, they become unstable at ca. 360 °C when either Rh and/or Pt are present, the effect of Rh being more pronounced. Nitrates decompose under different atmospheres: NO + O₂, He and H₂. The effect of Rh might be to form a thermally unstable complex (Rh–NO⁺) which takes part both in the formation of the nitrates when the catalyst is exposed to NOx and in the nitrates decomposition at higher temperatures. Regarding soot combustion, nitrates react with soot with a temperature of maximun reaction rate of ca. 370 °C, under tight contact conditions. This temperature is not affected by the presence of Rh, which indicates that the stability of nitrates has little effect on their reaction with soot.     

Potential rare earth modified CeO2 catalysts for soot oxidation: I. Characterisation and catalytic activity with O2

Ceria (CeO₂) and rare-earth modified ceria (CeReO_x with Re = La, Pr, Sm, Y) catalysts are prepared by nitrate precursor calcination and are characterised by BET surface area, XRD, H₂-TPR, and Raman spectroscopy. Potential of the catalysts in the soot oxidation is evaluated in TGA with a feed gas containing O₂. Seven hundred degree Celsius calcination leads to a decrease in the surface area of the rare-earth modified CeO₂ compared with CeO₂. However, an increase in the meso/macro pore volume, an important parameter for the soot oxidation with O₂, is observed. Rare-earth ion doping led to the stabilisation of the CeO₂ surface area when calcined at 1000 °C. XRD, H₂-TPR, and Raman characterisation show a solid solution formation in most of the mixed oxide catalysts. Surface segregation of dopant and even separate phases, in CeSmO_x and CeYO_x catalysts, are, however, observed. CePrO_x and CeLaO_x catalysts show superior soot oxidation activity (100% soot oxidation below 550 °C) compared with CeSmO_x, CeYO_x, and CeO₂. The improved soot oxidation activity of rare-earth doped CeO₂ catalysts with O₂ can be correlated with the increased meso/micro pore volume and stabilisation of external surface area. The segregation of the phases and the enrichment of the catalyst surface with unreducible dopant decrease the intrinsic soot oxidation activity of the potential CeO₂ catalytic sites. Doping CeO₂ with a reducible ion such as Pr^4+/3+ shows an increase in the soot oxidation. However, the ease of catalyst reduction and the bulk oxygen-storage capacity is not a critical parameter in the determination of the soot oxidation activity. During the soot oxidation with O₂, the function of the catalyst is to increase the ‘active oxygen’ transfer to the soot surface, but it does not change the rate-determining step, as evident from the unchanged apparent activation energy (around 150 kJ mol⁻¹), for the catalysed and un-catalysed soot oxidation. Spill over of oxygen on the soot surface and its subsequent adsorption at the active carbon sites is an important intermediate step in the soot oxidation mechanism.     

Theoretical and experimental study on the emission characteristics of waste plastics incineration by modified O2/RFG combustion technology

For mitigating the emission of greenhouse gas CO₂ from general air combustion systems, a clean combustion technology O₂/RFG is in development. The O₂/RFG combustion technology can significantly enhance the CO₂ concentration in the flue gas; however, using almost pure oxygen or pure CO₂ as feed gas is uneconomic and impractical. As a result, this study proposes a modified O₂/RFG combustion technology in which the minimum pure oxygen is mixed with the recycled flue gas and air to serve as the feed gas. The effects of different feed gas compositions and ratios of recycled flue gas on the emission characteristics of CO₂, CO and NO_x during the plastics incineration are investigated by theoretical and experimental approaches.Theoretical calculations were carried out by a thermodynamic equilibrium program and the results indicated that the emissions of CO₂ were increased with the O₂ concentrations in the feed gas and the ratios of recycled flue gas increased. Experimental results did not have the same trends with theoretical calculations. The best feed gas composition of the modified O₂/RFG combustion was 40% O₂ + 60% N₂ and the best ratio of recycled flue gas was 15%. As the O₂ concentration in feed gas and the ratio of recycled flue gas increased, the total flow rates and pressures of feed gas reduced. The mixing of solid waste and feed gas was incomplete and the formation of CO₂ decreased. Moreover, the emission of CO was decreased as the O₂ concentration in feed gas and the ratio of recycled flue gas increased. The emission of NO_x gradually increased with rising the ratio of recycled flue gas at lower O₂ concentration (<40%) but decreased at higher O₂ concentration (>60%).     

Adsorption of NO and NO2 on ceria–zirconia of composition Ce0.69Zr0.31O2: A DRIFTS study

In this study, the nature of surface intermediates generated by adsorption of NO and NO₂ on a commercial ceria–zirconia powder of composition Ce_0.69Zr_0.31O₂ was investigated using Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS). The conditions of occurrence of the main adsorbed species, i.e. nitrites and nitrates, are studied semi-quantitatively as a function of catalyst pre-treatment and/or type of adsorbed NO_x molecule. On the partially reduced ceria–zirconia, the primary role of NO_x is to re-oxidize the surface via adsorption/decomposition on reduced sites. By contrast, the formation of nitrites and nitrates readily occurs on oxidized surfaces, the latter kind of species being strongly promoted in the case of NO₂ adsorption only.     

Photocatalytic degradation of 4-nitrophenol in aqueous suspension by using polycrystalline TiO2 samples impregnated with Cu(II)-phthalocyanine

A number of supported metal oxide catalysts were screened for their catalytic performance for the oxidation of carbon black (CB; a model diesel soot) using NO₂ as the main oxidant. It was found that contact between the carbon and catalyst was a key factor in determining the rate of oxidation by NO₂. Oxides with low melting points, such as Re₂O₇, MoO₃ and V₂O₅ showed higher activities than did Fe₃O₄ and Co₃O₄. The activities of MoO₃ and V₂O₅ on various supporting materials were also examined. MoO₃/SiO₂ was the most active catalyst among the supported MoO₃ examined, whereas, V₂O₅/MCM-41 showed the highest activity among the supported V₂O₅. Different performances of the supported MoO₃ catalysts were explained by the interaction of MoO₃ with the supports: a strong MoO₃/support interaction may result in a poor mobility of MoO₃ and a poor activity for oxidation of carbon by NO₂. The high activity of V₂O₅/MCM-41 was associated with its catalysis of the oxidation of SO₂ by NO₂ to form SO₃, which substantially promotes oxidation of carbon by NO₂. Addition of transition metal oxides or sulfates to supported MoO₃ and V₂O₅ was also investigated. Combining MoO₃ or V₂O₅ with CuO on SiO₂, adding VOSO₄ to MoO₃/SiO₂ or MoO₃/Al₂O₃ and adding TiOSO₄ or CuSO₄ to V₂O₅/Al₂O₃ improved the catalytic performance.     

Role of vanadium sites in NO and O2 adsorption processes over VOx/CeO2-ZrO2 catalysts – EPR and IR studies

The interaction of NO and O₂ with 5 mol.% of vanadia deposited on Ce_0.10Zr_0.90O₂ and Ce_0.69Zr_0.31O₂ supports by wet impregnation was studied by means of EPR and IR. The supports were structurally characterized by XRD and Raman spectroscopy. Influence of the phase composition of the support on vanadium speciation as well as on surface architecture of the oxovanadium entities was discussed. The NO forms adsorbed on vanadium-containing systems were compared to those observed on bare CeO₂-ZrO₂ supports. The main products appearing on the catalysts surface during the consecutive reaction with NO and O₂ were identified and their thermal evolution was observed. Changes in vanadium speciation accompanying redox processes related to NO and O₂ activation were also observed and discussed.     

EPR studies on NO interaction with MoOx/t-ZrO2 catalysts obtained by slurry deposition

Variable temperature adsorption of nitric oxide on MoO₃ supported on tetragonal zirconia (MoO_x/t-ZrO₂), obtained by slurry deposition, was investigated by EPR spectroscopy. The influence of molybdenum loading and co-adsorbed oxygen on the adsorption process of NO was elucidated. Particular attention was devoted to redox character of NO activation. Another important aspect concerned is the nature of surface nitrosyl complexes of molybdenum and their thermal stability. The role of oxygen in NO transformation over catalyst surface was also discussed.     

Catalytic NO–H2–CO–O2 reactions over Pt-supported mesoporous yttrium oxide

Catalytic light-off of a stream of NO, H₂, CO in an excess O₂ has been studied over various metal oxides loading 1 wt% Pt. Because a low-surface area Y₂O₃ (<5 m² g⁻¹) was found to exhibit the highest de-NO_x activity, a mesoporous Y₂O₃ was then synthesized from an yttrium-based surfactant mesophase templated by dodecyl sulfate , which was anion-exchanged by acetate (AcO = CH₃COO⁻). The product showed a 3-D mesoporosity with a large surface area (396 m² g⁻¹) and the Pt-supported catalyst achieved much improved light-off characteristics suitable for the low-temperature de-NO_x in the presence of CO and excess O₂.     

Kinetic modeling of storage and reduction with different reducing agents (CO, H2, and C2 H4) on a Pt–Ba/-Al2O3 catalyst in the presence of CO2 and H2O

In this paper a global reaction kinetic model is used to understand and describe the NO_x storage/reduction process in the presence of CO₂ and H₂O. Experiments have been performed in a packed bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings at different temperatures (200, 250, and ) and using different reductants (H₂, CO, and C₂H₄). Model simulations and experimental results are compared. H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. The rate of NO storage increases with temperature. The reduction of stored NO with H₂ is complete for all investigated temperatures. At temperatures above , the water gas shift (WGS) reaction takes place and H₂ acts as reductant instead of CO. At , CO and C₂H₄ are not able to completely regenerate the catalyst. At the higher temperatures, C₂H₄ is capable of reducing all the stored NO, although C₂H₄ poisons the Pt sites by carbon decomposition at . The model adequately describes the NO breakthrough profile during 100 min lean exposure as well as the subsequent release and reduction of the stored NO. Further, the model is capable of simulating transient reactor experiments with 240 s lean and 60 s rich cycle timings.     

Methanol interaction with NO2: An attempt to identify intermediate compounds in CH4-SCR of NO with Co/Pd-HFER catalyst

The objective of this work is the study of fundamental common aspects of NO_x catalytic reduction over a Co/Pd-HFER zeolite catalyst, using methanol or methane as reducing agent. Temperature Programmed Surface Reaction (TPSR) studies were performed with reactant mixtures comprising NO₂ and one of the reducing agents.The formation of formaldehyde was detected in both studied reactions (NO₂–CH₄ and NO₂–CH₃OH) in the temperature range between 100 and 220 °C. At higher temperature, when the NO_x reduction process effectively begins, formaldehyde starts to be consumed.Using methanol as reducing agent, nitromethane and nitrosomethane, are detected. At 300 °C these species are consumed and cyanides and iso-cyanides formation occurs. On the contrary, with methane, these last species were not detected; however, there are strong evidences for CH₃NO and CH₃NO₂ formation.Thus, using methanol or methane, similar phenomena were detected. In both cases, common intermediary species seem to play an important role in the NO_x reduction process to N₂.These results suggest that methanol can be considered as a reaction intermediate species in the mechanism of the reduction of NO₂ with methane, over cobalt/palladium-based ferrierite catalysts.     

Methane activation by NO2 on Co loaded SBA-15 catalysts: The effect of mesopores (length, diameter) on the catalytic activity

In a general model of “three-function deNO_x” catalyst, the partial oxidation of methane by NO₂ is an important step (CH₄ + NO₂ → C_xH_yO_z + NO). To study the effect of the length and diameter, in the mesopores of SBA-15, we have synthesized catalysts with 3 wt.% cobalt supported on SBA-15, with differences in length and diameter of channels. Three different cobalt species were detected on all catalysts. We demonstrated by TPSR experiments that the activity of cobalt/SBA-15 catalysts is affected by the length, the diameter and connections between mesopores of the SBA-15 supports. We show that by changing textural properties of silica support the temperature of 100% conversion of NO₂ into NO can decrease by more than 100 °C.     

Oxidation of carbon by NOx, with particular reference to NO2 and N2O

The reactions reviewed here concern those between elemental carbon and NO₂, N₂O and NO, sometimes in the presence of oxygen. The section on NO includes only updates to recent reviews. Soots, activated carbons and carbon blacks are more reactive than graphite. The magnitudes of the reaction rates are found to be: NO₂ > N₂O ≈ NO ≈ O₂. The presence of a soluble organic fraction (SOF) in soot is found to influence some reactions, and all three reactions suffer from inhibition by surface products. The mechanisms proposed for the surface adsorbates are summarised. All authors found that two types of active site were present; one forming weak bonds (physisorption), and the other undergoing chemisorption to form groupings such as -C-ONO, -C-ONO₂ or -C-NO₂. The latter decompose to give oxides of carbon, and are sometimes called redox reactions. The adsorbates appear to be the same for all NO_x species. Some elemental nitrogen adsorption takes place, and can involve incorporation into the C skeleton. The attack of NO on carbon proceeds via NO₂, so that catalysts that facilitate this oxidation are effective. Gaseous SO₂ and H₂O assist in the process by forming acids which are good oxidants. The change in activation energy with temperature found experimentally for NO and N₂O may be due to the form of nitrogen on the edge carbon atoms.     

Simultaneous reduction of NOx and SO2 emissions from coal combustion by calcium magnesium acetate

The potential of calcium magnesium acetate (CMA) as a medium for the simultaneous control of NO_x and SO_x emissions has been investigated using a pulverized coal combustion rig operating at 80 kW. A US and a UK coal of significantly different sulphur contents were used as primary fuel and CMA was injected in solution form into the combustion gases by horizontally opposed twin-fluid atomisers at temperatures of 1100-1200 °C. SO₂ reductions typically greater than 80 and 70% were found for initial SO₂ levels of 1000 and 1500 ppm, respectively, at Ca/S ratios greater than 2.5. There did not appear to be significant limitation on sulphation by pore blockage using CMA due to the open structure formed during calcination and there is clear potential for zero SO₂ emissions at higher Ca/S ratios. The Ca content of the CMA in the form of CaO, via a droplet drying/particle calcination process, absorbs SO₂ by sulphation processes by penetration into the open pore structure of these particles. The effect of primary zone stoichiometry (λ₁=1.05, 1.15 and 1.4) on NO_x reduction was investigated for a range of CMA feed rates up to a coal equivalent of 24% of the total thermal input. NO_x reductions of 80, 50 and 30% were achieved at a primary zone stoichiometry of λ₁=1.05, 1.15 and 1.4, respectively, for a reburn zone residence time of 0.8 s. At lower equivalent reburn fuel fractions, coal gave greater NO_x reductions than CMA but similar levels were achieved above Rff=18%. The mechanism for NO_x reduction involves the organic fraction of CMA which pyrolyses into hydrocarbon fragments (CH_i), but to a lesser degree than coal, which may then react with NO_x in a manner similar to a conventional ‘reburn’ mechanism where NO_x is partly converted to N₂ depending on the availability of oxygen.