Influence of nanostructure composition on its morphometric characterization by different techniques

Morphometric characterization of nanoparticles is crucial to determine their biological effects and to obtain a formulation pattern. Determining the best technique requires knowledge of the particles being analyzed, the intended application of the particles, and the limitations of the techniques being considered. The aim of this article was to present transmission (TEM) and scanning (SEM) electron microscopy protocols for the analysis of two different nanostructures, namely polymeric nanoemulsion and poly(lactic‐co‐glycolic acid) (PLGA) nanoparticles, and to compare these results with conventional dynamic light scattering (DLS) measurements. The mean hydrodynamic diameter, the polydispersity index, and zeta potential of the nanostructures of polymeric nanoemulsion were 370.5 ± 0.8 nm, 0.133 ± 0.01, and ?36.1 ± 0.15 mV, respectively, and for PLGA nanoparticles were 246.79 ± 5.03 nm, 0.096 ± 0.025, and ?4.94 ± 0.86 mV, respectively. TEM analysis of polymeric nanoemulsion revealed a mean diameter of 374 ± 117 nm. SEM analysis showed a mean diameter of 368 ± 69 nm prior to gold coating and 448 ± 70 nm after gold coating. PLGA nanoparticles had a diameter of 131 ± 41.18 nm in TEM and 193 ± 101 nm in SEM. Morphologically, in TEM analysis, the polymeric nanoemulsions were spherical, with variable electron density, very few showing an electron‐dense core and others an electron‐dense surface. PLGA nanoparticles were round, with an electron‐lucent core and electron‐dense surface. In SEM, polymeric nanoemulsions were also spherical with a rough surface, and PLGA nanoparticles were round with a smooth surface. The results show that the “gold standards” for morphometric characterization of polymeric nanoemulsion and PLGA nanoparticles were, respectively, SEM without gold coating and TEM with negative staining. Microsc. Res. Tech. 77:691–696, 2014. © 2014 Wiley Periodicals, Inc.     

Ultrastructural characterization of isolated rat Kupffer cells by transmission X-ray microscopy

The ultrastructure of primary cultured rat Kupffer cells was studied using transmission X-ray microscopy as well as transmission electron microscopy. X-ray microscopical images of intact, hydrated Kupffer cells demonstrated structures such as cell nucleus separated by a nuclear membrane and filaments concentrated in the perinuclear area. Within the cytoplasm, a number of vacuoles were visible; some of these were crescent-shaped vacuoles that were half X-ray lucent, half X-ray dense; others were uniformly dense. The number of crescent-shaped vacuoles was predominant. After phagocytosis of haematite particles, enlarged vacuoles containing the ingested material were visible within the cytoplasm of Kupffer cells while crescent-shaped vacuoles were no longer detectable. Densitometric analysis of the two types of vacuole revealed that the X-ray absorption of the uniform vacuole was approximately half that of the dense part of the crescent-shaped vacuoles. This observation led to speculation on the existence of only one type of vacuole in the cytoplasm of Kupffer cells. The different morphological aspects — crescent-shaped versus uniform vacuoles — might be due to different three-dimensional orientation with respect to the image plane. Using transmission electron microscopy, the morphology of vacuoles differed more widely in diameter, density and shape. Two main types of vacuole were identified: electron-lucent and electron-dense. Based on the observation of only one type of vacuole by transmission X-ray microscopy, the different morphological aspects of vacuoles obtained by transmission electron microscopy could be explained by imaging several different sections of a crescent-shaped vacuole. From the present data it can be concluded that transmission X-ray microscopy is a versatile technique that reveals the ultrastructure of intact, unsectioned biological specimens in their aqueous environment, thereby allowing a more comprehensive interpretation of data obtained by transmission electron microscopy.     

Ultrastructural evaluation of mesenchymal stem cells from inflamed periodontium in different in vitro conditions

This research aimed to observe the behavior of mesenchymal stem cells (MSCs) isolated from periodontal granulation tissue (gt) when manipulated ex vivo to induce three‐dimensional (3D) spheroid (aggregates) formation as well as when seeded on two bone scaffolds of animal origin. Periodontal gt was chosen as a MSC source because of its availability, considering that it is eliminated as a waste material during conventional surgical therapies. 3D aggregates of cells were generated; they were grown for 3 and 7 days, respectively, and then prepared for transmission electron microscopic analysis. The two biomaterials were seeded for 72 h with gtMSCs and prepared for scanning electronic microscopic observation. The ultrastructural analysis of 3D spheroids remarked some differences between the inner and the outer cell layers, with a certain commitment observed at the inner cells. Both scaffolds showed a relatively smooth surface at low magnification. Macro‐ and micropores having a scarce distribution were observed on both bone substitutes. gtMSCs grew with relative difficulty on the biomaterials. After 72 h of proliferation, gtMSCs scarcely covered the surface of bovine bone scaffolds, demonstrating fibroblast‐like or star‐like shapes with elongated filiform extensions. Our results add other data on the possible usefulness of gtMSC and could question the current paradigm regarding the complete removal of chronically inflamed gts from the defects during periodontal surgeries. Until optimal protocols for ex vivo manipulation of MSCs are available for clinical settings, it is advisable to use biocompatible bone substitutes that allow the development of progenitor cells. Microsc. Res. Tech. 78:792–800, 2015. © 2015 Wiley Periodicals, Inc.     

Oral tissue response to ovine grafting biomaterial: Morphological and morphometric study using scanning electron and light microscopy tissue response to ovine grafting biomaterial

OBJECTIVE: To evaluate the oral tissue response to an experimental particle ovine biomaterial by scanning electron microscopy (SEM) and light microscopy (LM). MATERIAL AND METHODS: Forty‐eight rats had surgical periodontal defects treated with either blood clotting (control), bovine biomaterial? (B), or an experimental ovine biomaterial (O). Data from SEM analysis (defect exposure, root surface exposure, diameter of matrix fibers and bundles, and globuli areas; n = 5) were applied to Shapiro–Wilk, Kruskal–Wallis, and Dunn's test, whereas LM analysis (tissue cicatrization characteristics and diameter defect; n = 3) had data applied to two‐way analysis of variance. Animals were monitored for 1 and 3 weeks. RESULTS: By SEM, the O samples showed significant differences from B and C in the area of defect exposure (H_2,15 = 8.66; P < 0.05). In both periods, O and B samples showed similar results for matrix fiber diameters, differently than C samples (H_2,15 = 14.0; P < 0.05). All other SEM variables were considered equivalent among the groups (P > 0.05). Under LM, an acute and chronic granulomatous inflammation was seen in the presence of both biomaterials (B and O, 1 week); both the control and the ovine grafting samples showed mature bone in the repair site (3 weeks); the defect diameter showed similar values among groups, at both monitoring periods (F_2,12 = 1.0401; P > 0.05). CONCLUSION: The ovine particles of this study showed a favorable response to oral tissue repair, demonstrating to be a potential source for the development of bone grafting biomaterials. Microsc. Res. Tech. 2012. © 2012 Wiley Periodicals, Inc.     

A new approach for high-pressure freezing of primary culture cells: the fine structure and stimulation-associated transformation of cultured rabbit gastric parietal cells

A newly designated procedure for high‐pressure freezing of primary culture cells provided excellent ultrastructure of rabbit gastric parietal cells. The isolated parietal cells were cultivated on Matrigel‐coated aluminium plates for conventional subsequential cryoimmobilization by high‐pressure freezing. The ultrastructure of different organelles (Golgi apparatus, mitochondria, multivesicular bodies, etc.) was well preserved compared to conventional chemical fixation. In detail, actin filaments were clearly shown within the microvilli and the subapical cytoplasm. Another striking finding on the cytoskeleton system is the abundance of microtubules among the tubulovesicles. Interestingly, some microtubules appeared to be associating with tubulovesicles. A large number of electron‐dense coated pits and vesicles were observed around the apical membrane vacuoles in cimetidine‐treated resting parietal cells, consistent with an active membrane uptake in the resting state. Immunogold labelling of H⁺/K⁺‐ATPase was seen on the tubulovesicular membranes. When stimulated with histamine, the cultured parietal cells undergo morphological transformation, resulting in great expansion of apical membrane vacuoles. Immunogold labelling of H⁺/K⁺‐ATPase was present not only on the microvilli of expanded apical plasma membrane vacuoles but also in the electron‐dense coated pits. The present findings provide a clue to vesicular membrane trafficking in cultured gastric parietal cells, and assure the utility of the new procedure for high‐pressure freezing of primary culture cells.     

Immunophenotypic,immunocytochemistry, ultrastructural,and cytogenetic characterization of mesenchymal stem cells from equine bone marrow

The aim of this study was to isolate, culture, and characterize mesenchymal stem cells (MSCs) from horse bone marrow (BM) using the techniques of flow cytometry, immunocytochemistry, cytogenetics, and electron microscopy. Immunophenotypic analysis revealed the presence of MSCs with high expression of the CD90 marker, lower expression of the CD44 marker, and absent expression of the CD34 marker. In assays of differentiation, the positive response to osteogenic (OST), chondrogenic (CDG), and adipogenic (ADP) differentiation signals was observed and characterized by deposition of calcium‐rich extracellular matrix (OST), proteoglycans and collagen II (CDG) and intracellular deposition of fat drops (ADP). In immunocytochemical characterization, MSCs were immunopositive for CD44, vimentin, and PCNA, and they were negative for CD13. In the ultrastructural analysis of MSCs, the most outstanding characteristic was the presence of rough endoplasmic reticulum with very dilated cisterns filled with a low electrodensity material. Additionally, MSCs had normal karyotypes (2n = 64) as evidenced by cytogenetic analysis, and aneuploidy in metaphase was not observed. The protocols for isolating, culturing, and characterizing equine MSCs used in this study were shown to be appropriate for the production of a cell population with a good potential for differentiation and without aneuploidy that can be used to study future cellular therapies. Microsc. Res. Tech. 76:618–624, 2013. © 2013 Wiley Periodicals, Inc.     

Ultrastructural analysis of human bone marrow mesenchymal stem cells during in vitro osteogenesis and chondrogenesis

The main purpose of this article was to describe the morphology of mesenchymal stem cells (MSCs) differentiated in vitro towards osteogenic and chondrogenic lineages and to focus on the ultrastructural features associated with these processes. Human mononuclear cells (hMNC) were isolated, expanded, and analyzed for the expression of specific cell surface markers to demonstrate their stem cell characteristics. Human mononuclear cells were differentiated in vitro in an osteogenic and in a chondrogenic sense for 7, 14, 21, and 28 days. Subsequently, they were processed using electron microscopic analysis (FEISEM). Alizarin red and alcian blue staining were carried out to demonstrate the deposition of mineral salts and proteoglycans in the extracellular matrix. Undifferentiated MSCs showed a cell surface covered by filopodia and ondulopodia. During differentiation, the MSCs changed their shape from a round to a fibroblastic-like shape. At the end of the differentiation, several filaments with a parallel orientation in the osteogenic samples as well as a network organization in the chondrogenic samples were detected in the extracellular spaces. This study demonstrated that there are morphological features associated with the undifferentiated and differentiated states of the MSCs, which could be utilized as new parameters for identifying and classifying these cells.     

Combining Ar ion milling with FIB lift-out techniques to prepare high quality site-specific TEM samples

Focused ion beam (FIB) techniques can prepare site‐specific transmission electron microscopy (TEM) cross‐section samples very quickly but they suffer from beam damage by the high energy Ga⁺ ion beam. An amorphous layer about 20–30 nm thick on each side of the TEM lamella and the supporting carbon film makes FIB‐prepared samples inferior to the traditional Ar⁺ thinned samples for some investigations such as high resolution transmission electron microscopy (HRTEM) and electron energy loss spectroscopy (EELS). We have developed techniques to combine broad argon ion milling with focused ion beam lift‐out methods to prepare high‐quality site‐specific TEM cross‐section samples. Site‐specific TEM cross‐sections were prepared by FIB and lifted out using a Narishige micromanipulator onto a half copper‐grid coated with carbon film. Pt deposition by FIB was used to bond the lamellae to the Cu grid, then the coating carbon film was removed and the sample on the bare Cu grid was polished by the usual broad beam Ar⁺ milling. By doing so, the thickness of the surface amorphous layers is reduced substantially and the sample quality for TEM observation is as good as the traditional Ar⁺ milled samples.     

Correlative scanning electron and confocal microscopy imaging of labeled cells coated by indium‐tin‐oxide

Confocal microscopy imaging of cells allows to visualize the presence of specific antigens by using fluorescent tags or fluorescent proteins, with resolution of few hundreds of nanometers, providing their localization in a large field‐of‐view and the understanding of their cellular function. Conversely, in scanning electron microscopy (SEM), the surface morphology of cells is imaged down to nanometer scale using secondary electrons. Combining both imaging techniques have brought to the correlative light and electron microscopy, contributing to investigate the existing relationships between biological surface structures and functions. Furthermore, in SEM, backscattered electrons (BSE) can image local compositional differences, like those due to nanosized gold particles labeling cellular surface antigens. To perform SEM imaging of cells, they could be grown on conducting substrates, but obtaining images of limited quality. Alternatively, they could be rendered electrically conductive, coating them with a thin metal layer. However, when BSE are collected to detect gold‐labeled surface antigens, heavy metals cannot be used as coating material, as they would mask the BSE signal produced by the markers. Cell surface could be then coated with a thin layer of chromium, but this results in a loss of conductivity due to the fast chromium oxidation, if the samples come in contact with air. In order to overcome these major limitations, a thin layer of indium‐tin‐oxide was deposited by ion‐sputtering on gold‐decorated HeLa cells and neurons. Indium‐tin‐oxide was able to provide stable electrical conductivity and preservation of the BSE signal coming from the gold‐conjugated markers. Microsc. Res. Tech. 78:433–443, 2015. © 2015 Wiley Periodicals, Inc.     

Regularized phase tomography enables study of mineralized and unmineralized tissue in porous bone scaffold

Regularized phase tomography was used to image non‐calcified fibrous matrix in in vitro cell‐cultivated porous bone scaffold samples. 3D micro‐architecture of bone and bone scaffold has previously been studied by micro‐computed tomography, synchrotron radiation (SR) micro‐computed tomography and microdiffraction. However, neither of these techniques can resolve the low‐calcified immature pre‐bone fibrous structures. Skelite porous scaffold discs were seeded with osteoblasts, a combination of osteoblast and pre‐osteoclasts and, as controls, with pre‐osteoclasts only, and then cultivated for 8 weeks. They were subsequently imaged using SR propagation‐based phase contrast imaging. Reconstructions using a regularized holographic phase tomography approach were compared to standard (absorption) SR micro‐computed tomography, which show that quantitative analysis, such as volume and thickness measurements, of both the calcified fraction and the immature bone matrix in the reconstructed volumes is enabled. Indications of the effect of this type of culture on Skelite, such as change in mineralization and deposit of mature bone on the walls of the scaffold, are found. The results are verified with a histological study.     

Imaging analysis of the interface between osteoblasts and microrough surfaces of laser‐sintered titanium alloy constructs

Previous work using focused ion beam (FIB) analysis of osteoblasts on smooth and microrough Ti surfaces showed that the average cell aspect ratio and distance from the surface are greater on the rough surface. In order to better interrogate the relationship between individual cells and their substrate using multiple imaging modalities, we developed a method that tracks the same cell across confocal laser scanning microscopy (CLSM) to correlate surface microroughness with cell morphology and cytoskeleton; scanning electron microscopy (SEM) to provide higher resolution for observation of nanoroughness as well as chemical mapping via energy dispersive X‐ray spectroscopy; and transmission electron microscopy (TEM) for high‐resolution imaging. FIB was used to prepare thin sections of the cell‐material interface for TEM, or for three‐dimensional electron tomography. Cells were cultured on laser‐sintered Ti‐6Al‐4V substrates with polished or etched surfaces. Direct cell to surface attachments were observed across surfaces, though bridging across macroscale surface features occurred on rough substrates. Our results show that surface roughness, cell cytoskeleton and gross morphology can be correlated with the cell‐material cross‐sectional interface at the single cell level across multiple high‐resolution imaging modalities. This work provides a platform method for further investigating mechanisms of the cell‐material interface.     

Molecular ultrastructure of the urothelial surface: Insights from a combination of various microscopic techniques

The urothelium forms the blood–urine barrier, which depends on the complex organization of transmembrane proteins, uroplakins, in the apical plasma membrane of umbrella cells. Uroplakins compose 16 nm intramembrane particles, which are assembled into urothelial plaques. Here we present an integrated survey on the molecular ultrastructure of urothelial plaques in normal umbrella cells with advanced microscopic techniques. We analyzed the ultrastructure and performed measurements of urothelial plaques in the normal mouse urothelium. We used field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), transmission electron microscopy (TEM) on immunolabeled ultrathin sections (immuno‐TEM), and freeze‐fracture replicas (FRIL). We performed immunolabeling of uroplakins for scanning electron microscopy (immuno‐FESEM). All microscopic techniques revealed a variability of urothelial plaque diameters ranging from 332 to 1179 nm. All immunolabeling techniques confirmed the presence of uroplakins in urothelial plaques. FRIL showed the association of uroplakins with 16 nm intramembrane particles and their organization into plaques. Using different microscopic techniques and applied qualitative and quantitative evaluation, new insights into the urothelial apical surface molecular ultrastructure have emerged and may hopefully provide a timely impulse for many ongoing studies. The combination of various microscopic techniques used in this study shows how these techniques complement one another. The described advantages and disadvantages of each technique should be considered for future studies of molecular and structural membrane specializations in other cells and tissues. Microsc. Res. Tech. 77:896–901, 2014. © 2014 Wiley Periodicals, Inc.     

Low-energy electron microscopy (LEEM) and mirror electron microscopy (MEM) of biological specimens: Preliminary results with a novel beam separating system

Low-energy electron microscopy (LEEM) and mirror electron microscopy (MEM) utilize a parallel beam of slow-moving electrons backscattered from the specimen surface to form an image. If the electrons strike the surface an LEEM image is produced and if they are turned back just before reaching the surface an MEM image results. The applications thus far have been in surface physics. In the present study, applications of LEEM and MEM in the biological sciences are discussed. The preliminary results demonstrate the feasibility of forming images of uncoated cultured cells and cellular components using electrons in the threshold region (i.e. 0–10 V). The results also constitute a successful test of a novel beam-separating system for LEEM and MEM.     

Low-voltage transmission electron microscopy reveals SV40 viral particles within secretory granules in pancreatic cells

Novel approach in low voltage transmission electron microscopy (TEM) has revealed the presence of SV40 viral like particles in the secretory zymogen granules and in spherical membrane-bound dense bodies of SV40 infected pancreatic cells. The presence of SV40 antigen in these cellular compartments was confirmed by immunocytochemistry of the VP1 antigen. Visualization of the viral particles was only possible by examining ultrathin tissue sections with low-voltage TEM that significantly enhances imaging contrast. Results indicate that following infection of the cell entry and trafficking of the viral particles are present in unique cellular compartments such as ER, dense bodies, and secretory granules.     

Phosphorus detection in vitrified bacteria by cryo‐STEM annular dark‐field analysis

Bacterial cells often contain dense granules. Among these, polyphosphate bodies (PPBs) store inorganic phosphate for a variety of essential functions. Identification of PPBs has until now been accomplished by analytical methods that required drying or chemically fixing the cells. These methods entail large electron doses that are incompatible with low‐dose imaging of cryogenic specimens. We show here that Scanning Transmission Electron Microscopy (STEM) of fully hydrated, intact, vitrified bacteria provides a simple means for mapping of phosphorus‐containing dense granules based on quantitative sensitivity of the electron scattering to atomic number. A coarse resolution of the scattering angles distinguishes phosphorus from the abundant lighter atoms: carbon, nitrogen and oxygen. The theoretical basis is similar to Z contrast of materials science. EDX provides a positive identification of phosphorus, but importantly, the method need not involve a more severe electron dose than that required for imaging. The approach should prove useful in general for mapping of heavy elements in cryopreserved specimens when the element identity is known from the biological context.     

Developing 3D SEM in a broad biological context

When electron microscopy (EM) was introduced in the 1930s it gave scientists their first look into the nanoworld of cells. Over the last 80 years EM has vastly increased our understanding of the complex cellular structures that underlie the diverse functions that cells need to maintain life. One drawback that has been difficult to overcome was the inherent lack of volume information, mainly due to the limit on the thickness of sections that could be viewed in a transmission electron microscope (TEM). For many years scientists struggled to achieve three‐dimensional (3D) EM using serial section reconstructions, TEM tomography, and scanning EM (SEM) techniques such as freeze‐fracture. Although each technique yielded some special information, they required a significant amount of time and specialist expertise to obtain even a very small 3D EM dataset. Almost 20 years ago scientists began to exploit SEMs to image blocks of embedded tissues and perform serial sectioning of these tissues inside the SEM chamber. Using first focused ion beams (FIB) and subsequently robotic ultramicrotomes (serial block‐face, SBF‐SEM) microscopists were able to collect large volumes of 3D EM information at resolutions that could address many important biological questions, and do so in an efficient manner. We present here some examples of 3D EM taken from the many diverse specimens that have been imaged in our core facility. We propose that the next major step forward will be to efficiently correlate functional information obtained using light microscopy (LM) with 3D EM datasets to more completely investigate the important links between cell structures and their functions.     

Visualization of BrdU-labelled DNA in cyanobacterial cells by Hilbert differential contrast transmission electron microscopy

We have attempted to observe the native shape of DNA in rapidly frozen whole cyanobacterial cells through 5-bromo-2-deoxyuridine (BrdU) incorporation and visualization with a Hilbert differential contrast transmission electron microscopy (HDC TEM). The incorporation of BrdU into the DNA of Synechococcus elongatus PCC 7942 was confirmed with fluorescently labelled anti-BrdU antibodies and through EDX analysis of ultra-thin sections. HDC TEM observed cells that had incorporated BrdU into their DNA exhibited electron dense areas at the location corresponding to fluorescently labelled BrdU. Since various strings and strands were observed in high contrast with the HDC TEM, we conclude that the method promises to allow us to identify and understand bulk structural changes of the in vivo DNA and the nucleoid through observation at high resolution.     

Three‐dimensional Co‐culture of hepatic progenitor cells and mesenchymal stem cells in vitro and in vivo

Introduction: Here we co‐cultured hepatic progenitor cells (HPCs) and mesenchymal stem cells (MSCs) to investigate whether the co‐culture environments could increase hepatocytes form. Methods: Three‐dimensional (3D) co‐culture model of HPCs and MSCs was developed and morphological features of cells were continuously observed. Hepatocyte specific markers Pou5f1/Oct4, AFP, CK‐18 and Alb were analyzed to confirm the differentiation of HPCs. The mRNA expression of CK‐18 and Alb was analyzed by RT‐PCR to investigate the influence of co‐culture model to the terminal differentiation process of mature hepatocytes. The functional properties of hepatocyte‐like cells were detected by continuously monitoring the albumin secretion using Gaussia luciferase assays. Scaffolds with HPCs and MSCs were implanted into nude mouse subcutaneously to set up the in vivo co‐culture model. Results: Although two groups formed smooth spheroids and high expressed of CK‐18 and Alb, hybrid spheroids had more regular structures and higher cell density. CK‐18 and Alb mRNA were at a relatively higher expression level in co‐culture system during the whole cultivation time (P < 0.05). Albumin secretion rates in the hybrid spheroids had been consistently higher than that in the mono‐culture spheroids (P < 0.05). In vivo, the hepatocyte‐like cells were consistent with the morphological features of mature hepatocytes and more well‐differentiated hepatocyte‐like cells were observed in the co‐culture group. Conclusions: HPCs and MSCs co‐culture system is an efficient way to form well‐differentiated hepatocyte‐like cells, hence, may be helpful to the cell therapy of hepatic tissues and alleviate the problem of hepatocytes shortage. Microsc. Res. Tech. 78:688–696, 2015. © 2015 Wiley Periodicals, Inc.     

Quantitative and reliable in vitro method combining scanning electron microscopy and image analysis for the screening of osteotropic modulators

The increased generation and up-regulated activity of bone resorbing cells (osteoclasts) play a part in the impairment of bone remodeling in many bone diseases. Numerous drugs (bisphosphonates, calcitonin, selective estrogen receptor modulators) have been proposed to inhibit this increased osteoclastic activity. In this report, we describe a pit resorption assay quantified by scanning electron microscopy coupled with image analysis. Total rabbit bone cells with large numbers of osteoclasts were cultured on dentin slices. The whole surface of the dentin slice was scanned and both the number of resorption pits and the total resorbed surface area were measured. Resorption pits appeared at 48 h and increased gradually up to 96 h. Despite the observation of a strong correlation between the total resorption area and the number of pits, we suggest that area measurement is the most relevant marker for osteoclastic activity. Osteotropic factors stimulating or inhibiting osteoclastic activity were used to test the variations in resorption activity as measured with our method. This reproducible and sensitive quantitative method is a valuable tool for screening for osteoclastic inhibitors and, more generally, for investigating bone modulators.