HgCdTe Research at FFI: Molecular Beam Epitaxy Growth and Characterization

This paper presents results from recent work on molecular beam epitaxy growth of HgCdTe at the Norwegian Defence Research Establishment (FFI), including studies of material properties and fabrication of photodiodes and nanostructures. Systematic studies of defect morphology in HgTe and Hg_1−x Cd _x Te have revealed that there is a minimum in the area covered by defects just below the onset of Te precipitation. The shape and density of microvoids in HgTe can be used to determine the deviation from the optimal growth temperature. This can be further related to the optimal growth temperature of Hg_1−x Cd _x Te with any Cd mole fraction by thermodynamic calculations. A mechanism for the formation of microvoids and needles has been presented. Photoluminescence (PL) has been used to study layers without doping and with Hg vacancy, Ag, and In doping. Planar photodiodes with high dynamic resistance and good quantum efficiency were fabricated by ion-milling vacancy-doped mid-wave and long-wave infrared layers. Quantum wells (QWs) with good crystallinity and high PL light output have been grown. Surface patterning has been found to enhance light emission from HgCdTe thin-film and QW samples by ∼30%. Single-crystal HgTe and segmented HgTe/Te nanowires have been grown, and the resistivity of the nanowires has been measured by conductive atomic force microscopy (AFM), where the AFM tip has been used as a mobile electrode.     

HgCdZnTe quaternary materials for lattice-matched two-color detectors

As the number of bands and the complexity of HgCdTe multicolor structures increases, it is desirable to minimize the lattice mismatch at growth interfaces within the device structure in order to reduce or eliminate mismatch dislocations at these interfaces and potential threading dislocations that can degrade device performance. To achieve this we are investigating the use of Hg_1−x−yCd_xZn_yTe quaternary alloys which have an independently tunable lattice constant and bandgap. Lattice matching in Hg_1−x−yCd_xZn_yTe structures can be achieved using small additions of Zn (y<0.015) to HgCdTe ternary alloys. We have investigated some of the basic properties of Hg_1−x−yCd_xZn_yTe materials with x≈0.31 and 0≤y≤0.015. The quaternary layers were grown on (112)CdZnTe substrates using MBE and the amount of Zn in the layers was determined from calibrated SIMS measurements. As expected, the lattice constant decreased and the bandgap increased as Zn was added to HgCdTe to form Hg_1−x−yCd_xZn_yTe. Hall-effect results for both n-type (In) and p-type (As) Hg_1−x−yCd_xZn_yTe layers were very similar to HgCdTe control samples. We have also utilized x-ray rocking curve measurements with (246) asymmetric reflections as a novel sensitive technique to determine the correct amount of Zn needed to achieve lattice matching at an interface. MWIR/LWIR n-p-n two-color triple-layer heterojunction structures were grown to evaluate the effects of minimizing the lattice mismatch between the widest bandgap p-type collector layer, using Hg_1−x−yCd_xZn_yTe, and the HgCdTe MWIR and LWIR collector layers and compared to structures that did not incorporate the quaternary. Sequential mode two-color detectors were fabricated using a 256 × 256, 30 μm unit cell design. There were several interesting findings. Macro defects predominantly affected the LWIR band (Band 2) operability and had little effect on the MWIR band (Band 1). The incorporation of Hg_1−x−yCd_xZn_yTe p-type collector layers had little effect on MWIR detector performance, but overall the LWIR performance was generally better. These initial detector results indicate that the use of Hg_1−x−yCd_xZn_yTe alloys in multicolor detector structures are potentially promising and should be pursued further.     

Examination of the effects of high-density plasmas on the surface of HgCdTe

High-density argon-hydrogen plasmas have been demonstrated to be very effective as etchants of CdTe, CdZnTe, and HgCdTe materials for focal plane array applications. Understanding the physical, chemical, and electrical characteristics of these surfaces is critical in elucidating the mechanisms of processing Hg_1−xCd_xTe. The ways in which these plasmas interact with HgCdTe, such as etch rates and loading, have been studied.^1–11 However, little is known on how these plasmas affect the first few atomic layers of HgCdTe. In this study, the effects of high-density plasmas on the surface of HgCdTe were examined. The combination of argon and hydrogen plasma etch leaves a well-ordered, near-stoichiometric surface determined by both x-ray photoelectron spectroscopy and reflection high-energy electron diffraction (RHEED). Starting with Hg_0.78Cd_0.22Te, we were able to produce surfaces with x=0.4 and a RHEED pattern sharp enough to measure 2×1 reconstruction.     

X-ray Diffraction Imaging of Improved Bulk-Grown CdZnTe(211) and Its Comparison with Epitaxially Grown CdTe Buffer Layers on Si and Ge Substrates

Large-area high-quality Hg_1–x Cd _x Te sensing layers for infrared imaging in the 8 μm to 12 μm spectral region are typically grown on bulk Cd_1–x Zn _x Te substrates. Alternatively, epitaxial CdTe grown on Si or Ge has been used as a buffer layer for high-quality epitaxial HgCdTe growth. In this paper, x-ray topographs and rocking-curve full-width at half-maximum (FWHM) data will be presented for recent high-quality bulk CdZnTe grown by the vertical gradient freeze (VGF) method, previous bulk CdZnTe grown by the vertical Bridgman technique, epitaxial CdTe buffer layers on Si and Ge, and a HgCdTe layer epitaxially grown on bulk VGF CdZnTe.     

HgCdTe heteroepitaxy on three-inch (112) CdZnTe/Si: Ellipsometric control of substrate temperature

The technique of spectroscopic ellipsometry (SE) has been utilized to monitor in real-time and precisely control the surface temperature of Hg_1−xCd_xTe during molecular beam epitaxy. Due to the temperature dependence of the Hg sticking coefficient under Hg-deficient growth conditions, the near-surface composition of an epilayer is extremely sensitive to surface temperature. SE data were acquired in real time and modeled using a previously established library of dielectric functions of Hg_1−xCd_xTe as a function of composition. Utilizing SE-generated compositional profiles as a guide, substrate heating power was adjusted in such a way as to minimize composition transients. To demonstrate the effectiveness of the technique, we have used SE to control the temperature of HgCdTe epilayer surfaces during deposition on three-inch (211)CdZnTe/ZnTe/Si composite substrates mounted on indium free holders.     

Ten-inch molecular beam epitaxy production system for HgCdTe growth

Growth of Hg_1−xCd_xTe by molecular beam epitaxy (MBE) has been under development since the early 1980s at Rockwell Scientific Company (RSC), formerly the Rockwell Science Center; and we have shown that high-performance and highly reproducible MBE HgCdTe double heterostructure planar p-on-n devices can be produced with high throughput for various single- and multiplecolor infrared applications. In this paper, we present data on Hg_1−xCd_xTe epitaxial layers grown in a ten-inch production MBE system. For growth of HgCdTe, standard effusion cells containing CdTe and Te were used, in addition to a Hg source. The system is equipped with reflection high energy electron diffraction (RHEED) and spectral ellipsometry in addition to other fully automated electrical and optical monitoring systems. The HgCdTe heterostructures grown in our large ten-inch Riber 49 MBE system have outstanding structural characteristics with etch-pit densities (EPDs) in the low 10⁴ cm⁻² range, Hall carrier concentration in low 10¹⁴ cm⁻³, and void density <1000 cm². The epilayers were grown on near lattice-matched (211)B Cd_0.96Zn_0.04Te substrates. High-performance mid wavelength infrared (MWIR) devices were fabricated with R₀A values of 7.2×10⁶ Ω-cm² at 110 K, and the quantum efficiency without an antireflection coating was 71.5% for cutoff wavelength of 5.21 μm at 37 K. For short wavelength infrared (SWIR) devices, an R₀A value of 9.4×10⁵ Ω-cm² at 200 K was obtained and quantum efficiency without an antireflection coating was 64% for cutoff wavelength of 2.61 μm at 37 K. These R₀A values are comparable to our trend line values in this temperature range.     

Performance limitation of short wavelength infrared InGaAs and HgCdTe photodiodes

The carrier lifetimes in In_xGa_1−xAs (InGaAs) and Hg_1−xCd_xTe (HgCdTe) ternary alloys for radiative and Auger recombination are calculated for temperature 300K in the short wavelength range 1.5<λ<3.7 μm. Due to photon recycling, an order of magnitude enhancements in the radiative lifetimes over those obtained from the standard van Roosbroeck and Shockley expression, has been assumed. The possible Auger recombination mechanisms (CHCC, CHLH, and CHSH processes) in direct-gap semiconductors are investigated. In both n-type ternary alloys, the carrier lifetimes are similar, and competition between radiative and CHCC processes take place. In p-type materials, the carrier lifetimes are also comparable, however the most effective channels of Auger mechanism are: CHSH process in InGaAs, and CHLH process in HgCdTe. Next, the performance of heterostructure p-on-n photovoltaic devices are considered. Theoretically predicted R_oA values are compared with experimental data reported by other authors. In_0.53Ga_0.47As photodiodes have shown the device performance within a factor often of theoretical limit. However, the performance of InGaAs photodiodes decreases rapidly at intermediate wavelengths due to mismatch-induced defects. HgCdTe photodiodes maintain high performance close to the ultimate limit over a wider range of wavelengths. In this context technology of HgCdTe is considerably advanced since the same lattice parameter of this alloy is the same over wide composition range.     

Growth of HgTe Quantum Wells for IR to THz Detectors

We zone-engineered HgCdTe/HgTe/HgCdTe quantum wells (QWs) using the molecular-beam epitaxy (MBE) method with in situ high-precision ellipsometric control of composition and thickness. The variations of ellipsometric parameters in the ψ–Δ plane were represented by smooth broken curves during HgTe QW growth with abrupt composition changes. The form of the spiral fragments and their extensions from fracture to fracture revealed the growing layer composition and its thickness. Single and multiple (up to 30) Cd _x Hg_1−x Te/HgTe/Cd _x Hg_1−x Te QWs with abrupt changes of composition were grown reproducibly on (013) GaAs substrates. HgTe thickness was in the range of 16 nm to 22 nm, with the central portion of Cd _x Hg_1−x Te spacers doped by In to a concentration of 10¹⁴ cm⁻³ to 10¹⁷ cm⁻³. Based on this research, high-quality (013)-grown HgTe QW structures can be used for all-electric detection of radiation ellipticity in a wide spectral range, from far-infrared (terahertz radiation) to mid-infrared wavelengths. Detection was demonstrated for various low-power continuous-wave (CW) lasers and high-power THz pulsed laser systems.     

Large area depositon of Cd1-xZnxTe on GaAs and Si substrates by metalorganic chemical vapor deposition

Results of large-area (up to 1000 cm²/run) Cd_1-xZn_xTe heteroepitaxy on both GaAs and GaAs/Si substrates by metalorganic chemical vapor deposition (MOCVD) are presented. Cd_1-xZn_xTe (x = 0-0.1) films exhibited specular surface morphology, 1% thickness uniformity (standard deviation), and compositional uniformity (Δx) of ±0.002 over 100 mm diam substrates. For selected substrate orientations and deposition conditions, the only planar defects exhibited by (lll)B Cd_1-xZn_xTe/GaAs/Si films were lamella twins parallel to the CdTe/GaAs interface; these do not propagate through either the Cd_1-xZn_xTe layer or subsequently deposited liquid phase epitaxy (LPE) HgCdTe layer(s). Background Ga and As-impurity levels for Cd_1-xZn_xTe on GaAs/Si substrates were below the secondary ion mass spectroscopy detection limit. Preliminary results of HgCdTe liquid phase epitaxy using a Te-rich melt on Si-based substrates resulted in x-ray rocking curve linewidths as narrow as 72 arc-sec and etch-pit densities in the range 1 to 3 x 10⁶ cm².     

HgCdTe composition determination using spectroscopic ellipsometry during molecular beam epitaxy growth of near-infrared avalanche photodiode device structures

The application of spectroscopic ellipsometry (SE) for real-time composition determination during molecular beam epitaxy (MBE) growth of Hg_1−xCd_xTe alloys with x>0.5 is reported. Techniques previously developed for SE determination of composition in long-wavelength infrared (LWIR) HgCdTe have been successfully extended to near-infrared HgCdTe avalanche photodiode (APD) device structures with x values in the range of 0.6–0.8. Ellipsometric data collected over a spectral range of 1.7–5 eV were used to measure depth profiles of HgCdTe alloy composition through the use of an optical model of the growth surface. The optical model used a dielectric-function database collected through the growth of a set of HgCdTe calibration samples with x ranging from 0.6 to 0.8. The sensitivity of this SE method of composition determination is estimated to be Δx ∼0.0002 at x=0.6, which is sufficiently low to sense composition changes arising from flux variations of less than 0.1%. Errors in composition determination because of Hg-flux variations appear to be inconsequential, while substrate-temperature fluctuations have been observed to alter the derived composition at a rate of −0.0004/°C. By comparing the composition inferred from SE and postgrowth 300 K IR transmission measurements on a set of APD device structures, the run-to-run precision of the Se-derived composition (at x=0.6) is estimated to be ±0.0012, which is equivalent to the precision achieved with the same instrumentation during the growth of mid-wavelength infrared (MWIR) HgCdTe alloys in the same MBE system.     

Liquidus isotherms,solidus lines and LPE growth in the Te-rich corner of the Hg-Cd-Te system

Liquidus isotherms for the Hg_1−xCd_xTe primary phase field in the Te-rich corner of the Hg-Cd-Te ternary system have been determined for temperatures from 425 to 600‡C by a modified direct observational technique. These isotherms were used to help establish conditions for the open-tube liquid phase epitaxial growth of Hg_1−xCd_xTe layers on CdTe_1−ySe_y substrates. Layers with x ranging from 0.1 to 0.8 have been grown from Te-rich HgCdTe solutions under flowing H₂ by means of a horizontal slider technique that prevents loss of Hg from the solutions by evaporation. Growth temperatures and times of 450–550‡C and 0.25–10 min, respectively, have been used. The growth solution equilibration time is typically 1 h at 550‡C. Source wafers, supercooled solutions, and (111)-oriented substrates were employed in growing the highest quality layers, which were between 3 and 15 Μm thick. Electron microprobe analysis was used to determine x for the epitaxial layers, and the resulting data, along with the liquidus isotherms, were used to obtain solidus lines. In addition to EMP data, optical transmission results are given. This work was sponsored by the Department of the Air Force and the U. S. Army Research Office.     

Optical and Structural Properties of CdTe Grown by Molecular Beam Epitaxy at Low Temperature for Resonant-Cavity-Enhanced HgCdTe Detectors

Investigation into resonant-cavity-enhanced (RCE) HgCdTe detectors has revealed a discrepancy in the refractive index of the CdTe layers grown by molecular beam epitaxy (MBE) for the detectors, compared with the reported value for crystalline CdTe. The refractive index of the CdTe grown for RCE detectors was measured using ellipsometry and matches that of CdTe with an inclusion of approximately 10% voids. X-ray measurements confirm that the sample is crystalline and strained to match the lattice spacing of the underlying Hg_(1−x)Cd_(x)Te, while electron diffraction patterns observed during growth indicate that the CdTe layers exhibit some three-dimensional structure. Secondary ion mass spectroscopy results further indicate that there is enhanced interdiffusion at the interface between Hg_(1−x)Cd_(x)Te and CdTe when the Hg_(1−x)Cd_(x)Te is grown on CdTe, suggesting that the defects are nucleated within the CdTe layers.     

Electronic structure, absorption coefficient, and auger rate in HgCdTe and thallium-based alloys

The band structures, absorption coefficients, and Auger recombination rates in narrow-gap alloys HgCdTe, InTIP, InTlAs, and InTlSb in the zinc blende structure, along with those of GaAs, are calculated using a hybrid pseudopotential and tight-binding method. The composition-dependent band gaps of the thallium-based alloys are reported along with those of several other semiconductor alloys. Within 50 meV from the absorption edge, the absorption coefficient of In_xTl_1−xP is found to have about the same magnitude as that of Hg_xCd_1−xTe and GaAs, while that of In_xTl_1−xAs and In_xTl_1−xSb is much smaller. In agreement with previous theories, the calculated Auger lifetimes in Hg_0.78Cd_0.22Te with unit or k • p overlap agree very well with experiments. Among the thallium alloys studied, the Auger lifetimes are longest in In_0.33Tl_0.67P, but still shorter than those in Hg_0.78Cd_0.22Te by an order of magnitude. In addition, realistic overlaps produce lifetimes one to two orders of magnitude larger than those observed.     

Molecular beam epitaxial growth of HgCdTe on CdZnTe(311)B

A series of n-type, indium-doped Hg_1−xCd_xTe (x∼0.225) layers were grown on Cd_0.96Zn_0.04Te(311)B substrates by molecular beam epitaxy (MBE). The Cd_0.96Zn_0.04Te(311)B substrates (2 cm × 3 cm) were prepared in this laboratory by the horizontal Bridgman method using double-zone-refined 6N source materials. The Hg_1−xCd_xTe(311)B epitaxial films were examined by optical microscopy, defect etching, and Hall measurements. Preliminary results indicate that the n-type Hg_1−xCd_xTe(311)B and Hg_1−xCd_xTe(211)B films (x ∼ 0.225) grown by MBE have comparable morphological, structural, and electrical quality, with the best 77 K Hall mobility being 112,000 cm²/V·sec at carrier concentration of 1.9×10⁺¹⁵ cm⁻³.     

MBE HgCdTe on Alternative Substrates for FPA Applications

Results of first-principles calculations and experiments focusing on molecular beam epitaxy (MBE) growth of HgCdTe on the alternative substrates of GaAs and Si are described. The As passivation on (2 × 1) reconstructed (211) Si and its effects on the surface polarity of ZnTe or CdTe were clarified by examining the bonding configurations of As. The quality of HgCdTe grown on Si was confirmed to be similar to that grown on GaAs. Typical surface defects in HgCdTe and CdTe were classified. Good results for uniformities of full width at half maximum (FWHM) values of x-ray rocking curves, surface defects, and x values of Hg_1−x Cd _x Te were obtained by refining the demanding parameters and possible tradeoffs. The sticking coefficient of As₄ for MBE HgCdTe was determined. The effects of Hg-assisted annealing for As activation were investigated experimentally and theoretically by examining the difference of the formation energy of As_Hg and As_Te. Results of focal-plane arrays (FPAs) fabricated with HgCdTe grown on Si and on GaAs are discussed.     

Flexibility of p–n Junction Formation from SWIR to LWIR Using MBE-Grown Hg(1–x)CdxTe on Si Substrates

In this paper, we show the versatility of using molecular-beam epitaxy (MBE) for the growth of the mercury cadmium telluride (HgCdTe) system. Abrupt composition profiles, changes in doping levels or switching doping types are easily performed. It is shown that high-quality material is achieved with Hg_(1–x)Cd _x Te grown by MBE from a cadmium mole fraction of x = 0.15 to x = 0.72. Doping elements incorporation as low as 10¹⁵ cm⁻³ for both n-type and p-type material as well as high incorporation levels >10¹⁸ cm⁻³ for both carrier types were achieved. X-ray curves, secondary-ion mass spectrometry (SIMS) data, Hall data, the influence of doping incorporation with cadmium content and growth rate, etch pit density (EPD), composition uniformity determined from Fourier-transform infrared (FTIR) transmission spectro- scopy, and surface defect maps from low to high x values are presented to illustrate the versatility and quality of HgCdTe material grown by MBE. All data presented in this work are from layers grown on silicon (112) substrate.     

Interrelations between defects in the Hg1−xCdxTe epilayers and their measured lattice parameters and composition

Absolute values of lattice parameters in Hg_1−xCd_xTe epilayers were precisely measured by high-resolution x-ray diffraction (Bond method), and then compared with those calculated using Cd contents, x, which were derived from Fourier transform infrared transmission spectra. A part of the samples revealed significant discrepancies between measured and calculated lattice parameters, the differences being both of positive and negative signs. The obtained results are discussed in the framework of clusters of the point defects that were visualized by high-resolution scanning electron microscopy.     

Development of Molecular Beam Epitaxially Grown Hg<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Cd<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Te for High-Density Vertically-Integrated Photodiode-Based Focal Plane Arrays

Hg_1−x Cd _x Te samples of x ~ 0.3 (in the midwave infrared, or MWIR, spectral band) were prepared by molecular beam epitaxy (MBE) for fabrication into 30-μm-pitch, 256 × 256, front-side-illuminated, high-density vertically-integrated photodiode (HDVIP) focal plane arrays (FPAs). These MBE Hg_1−x Cd _x Te samples were grown on CdZnTe(211) substrates prepared in this laboratory; they were ~10-μm thick and were doped with indium to ~5 × 10¹⁴ cm⁻³. Standard HDVIP process flow was employed for array fabrication. Excellent array performance data were obtained from these MWIR arrays with MBE HgCdTe material. The noise-equivalent differential flux (NEΔΦ) operability of the best array is 99.76%, comparable to the best array obtained from liquid-phase epitaxy (LPE) material prepared in this laboratory.     

Effects of a-Si:H resist vacuum-lithography processing on HgCdTe

A vacuum-compatible process for carrying out lithography on Hg_1−xCd_xTe and CdTe films was previously demonstrated. It was shown that hydrogenated amorphous silicon (a-Si:H) could be used as a dry resist by projecting a pattern onto its surface using excimer laser irradiation and then developing that pattern by hydrogen plasma etching. Pattern transfer to an underlying Hg_1−xCd_xTe film was then carried out via Ar/H₂ plasma etching in an electron cyclotron resonance (ECR) reactor. Despite the successful demonstration of pattern transfer, the possibility of inducing harmful effects in the Hg_1−xCd_xTe film due to this vacuum lithography procedure had not been explored. Here we present structural and surface compositional analyses of Hg_1−xCd_xTe films at key stages of the a-Si:H vacuum lithography procedure. X-ray diffraction double crystal rocking curves taken before and after a-Si:H deposition and after development etching were identical, indicating that bulk structural changes in the Hg_1−xCd_xTe film are not induced by these processes. Cross-section transmission electron microscopy studies show that laser-induced heating in the 350 nm thick a-Si:H overlayer is not sufficient to cause structural damage in the underlying Hg_1−xCd_xTe surface. In vacuo surface analysis via Auger electron spectroscopy and ion scattering spectroscopy suggest that the hydrogen plasma development process produces Hg-deficient surfaces but does not introduce C contamination. However, after ECR plasma etching into the Hg_1−xCd_xTe film, the measured x value is much closer to that of the bulk.     

Microstructural development of directionally solidified Hg1−xZnxSe alloys

Hg_1−xZn_xSe alloys have been studied as an alternative to Hg_1−xCd_xTe for the detection of electromagnetic radiation, because the shorter ZnSe and HgSe bonds have been predicted to improve lattice stability. Several ingots with x=0.1 were directionally solidified using a modified Bridgman-Stockbarger method; one was grown in an applied magnetic field, which greatly reduced radial compositional variations. A method was developed to reduce wetting. This, combined with the convex liquid-solid interface shape, produced boules that were single crystalline after growing ∼3.5 cm. Observed surface features indicated ampoule wetting was eliminated using a graphite getter. Microstructural characteristics were greatly improved over HgCdTe alloys. In six boules, a total of only one twin was observed. A method for polishing and producing dislocation etch pits was developed for these alloys, revealing dislocation etch pit densities one to two orders of magnitude less than HgTe-based alloys. A kink in the thermal profile during processing of one boule generated more dislocations than did lattice mismatch due to compositional variations. This alloy has improved microstructural properties and resistance to dislocation formation compared with similar II–VI alloys.