交叉耦合盒式结构微带带通滤波器设计

设计了一种交叉耦合盒式结构微带带通滤波器。采用耦合矩阵方法对交叉耦合盒式结构带通滤波器频率响应特性进行了分析,并且在此基础上研制了一种基于E型双模谐振器的非对称响应带通滤波器。滤波器中心频率为6.4 GHz,带宽为0.8 GHz,最小带内插损为1.9 dB,两个传输零点分别位于4.5 GHz 和7.6 GHz,上下阻带抑制度分别大于35dB、47dB。滤波器有效尺寸约为0.34λg *0.43λg。该滤波器具有结构紧凑、带外抑制度高、选择性高的优点。     

改善开环谐振器间电耦合系数色散现象的微扰结构设计

以耦合矩阵综合方法设计的交叉耦合滤波器由于谐振器间耦合系数的色散现象,使滤波器的实际响应与理论综合得到的响应存在差异。针对此情况,首先研究了开环谐振器间电耦合系数随频率的变化趋势及其对交叉耦合滤波器中传输零点位置的影响,随后设计了一种加载于谐振器间的U型微扰结构,通过调节其物理尺寸及位置可以降低耦合系数的色散现象,优化滤波器带外传输零点的分布。基于上述思路,分别设计了传统CQ结构以及加载微扰结构的CQ结构滤波器,其中心频率和通带带宽分别为20.6 GHz和1.4 GHz,加载有微扰结构的滤波器其低频端带外零点相较于传统滤波器从18.6 GHz移动至19.4 GHz,且带内特性和高端传输零点均未受到影响,最终实测结果与仿真结果基本一致。     

一种基于SIR结构的三通带带通滤波器

应用双指耦合结构和枝节加载谐振器（Stub-loaded Resonator,SLR）实现了一款基于阶梯阻抗谐振器（Stepped Impedance Resonator,SIR）的滤波器。该滤波器具有3个通带,带外抑制较好,工作频段提高。通过调整阻抗比可调节第二、三通带的谐振频率;SLR结构能够增加通带数量;SLR结构和双指耦合结构均能改善滤波器的S参数。HFSS软件仿真表明,3个通带的中心频率分别为3.5 GHz、6.6 GHz、9.2 GHz,对应的分数带宽分别为5.7%、3%、2%,S11分别为-18 dB、-22 dB、-24 dB,通带内的S21分别为-1.8 dB、-1 dB、-1 dB。电路的测量结果与仿真结果较为吻合。该滤波器在5G通信的低频段具有应用前景。     

基于十字形谐振器的W波段可重构滤波器设计北大核心CSCD

本文提出了一种采用十字形结构的W波段滤波器,主要由左右对称十字形谐振器和输入输出耦合线构成。通过对十字形谐振器进行奇偶模分析,可得谐振频率与短路枝节臂长的关系,滤波器工作带宽可以通过谐振器的臂长来控制。通过耦合线两端接地来实现带通到带阻的可重构。为了便于W波段加工与测试,本文还设计了波导(WR10)与微带的转换结构。最后对其进行仿真优化并给出滤波器的结构参数。仿真结果显示,在带通模式下,中心频率93GHz回波损耗优于15dB,插入损耗优于1.5dB,在带阻模式下,78GHz～98GHz隔离度优于30dB。     

基于λ/4和非对称λ/2谐振器的三阶微带滤波器设计

提出了一种基于电容加载 λ/4 梳状线谐振器和电容加载非对称 λ/2准梳状线谐振器的三阶耦合滤波器拓扑结构。利用奇偶模方法,给出并分析了整个滤波器结构的等效电路,由导纳矩阵可以得出传输零点的位置。实际制作了一个中心频率为1.83 GHz的三阶微带带通滤波器,相对带宽为9%,带内中心插损仅为1.45 dB,回波损耗优于14 dB。传输响应在通带两侧分别存在一个传输零点,有利于提高滤波器的选择性。实验结果表明,测试结果与仿真结果基本一致。     

横向双模双频滤波器设计

基于横向滤波器耦合结构,采用支节加载双模谐振器,设计了中心频率位于1.57 GHz(GPS应用)与2.4GHz(WLAN应用)的双频微带滤波器。由短路支节加载双模谐振器形成第一个通带,开路支节加载双模谐振器形成第二个通带,两个谐振器被输入/输出馈线隔离,每个通带的中心频率与带宽可以单独调节。测试结果表明:两个通带内的最小插损分别为2.18,1.35 dB,3 dB带宽分别为5.2%,6.8%,回波损耗均小于16 dB,三个传输零点分别位于1.28,2.08,2.71 GHz处。该滤波器具有尺寸小、带外选择性好等优点。     

SIR实现的新型毫米波UWB滤波器

提出了一个用阶跃阻抗谐振器(SIR)实现的毫米波超宽带(UWB)滤波器。滤波器的基本单元是一个由半波长微带线谐振器和SIR组成的三模谐振器。该谐振器采用SIR结构,从而达到阻带宽、结构紧凑,且能很好地改善带外抑制。为了进一步改善阻带特性,该三模谐振器与半波长谐振器平行耦合形成新型的滤波器。该滤波器有多个传输极点和传输零点,形成陡峭的通带边缘特性和很宽的阻带。实验测得滤波器的-3 dB相对带宽为35.7%,通带内的插入损耗约为-1.7 dB。插入损耗低于-17 dB的高频端阻带可到76 GHz。滤波器的仿真结果和测试结果基本吻合。     

基于阶梯阻抗谐振器的双频微带带通滤波器设计

设计了一种基于1/4波长阶梯阻抗谐振器(SIR)的交叉耦合微带双频带通滤波器,利用SIR终端加载的金属化短路通孔实现K倒置器,利用谐振器之间的级间耦合实现J倒置器,通过相邻谐振器之间的级联耦合和不相邻谐振器之间的交叉耦合,完成了四阶双频带通滤波器的设计。滤波器两个通带的中心频率分别为3.78GHz和8.69GHz,中心频率比大于2,对应的插入损耗分别为-1.28dB和-2.29dB,带内回波损耗分别为-12.38dB和-25.0dB。测量结果和仿真结果基本吻合,实现了双频带通滤波器的小型化和低损耗。     

基于枝节加载谐振器的新型三频带通滤波器设计

提出了一种新型平面三频带通滤波器,该滤波器由一个加载短路枝节的阶梯阻抗谐振器,一对加载开路枝节的背靠背E型谐振器,以及包含源负载直接耦合的馈电结构组成.所采用的枝节加载谐振器的多模工作特性使滤波器的体积大大减小,同时每个通带的位置及其耦合特性都能够独立调谐.另外,通过源负载直接耦合引入通带两侧的传输零点,实现了滤波器良好的频率选择性.最后设计并加工了一款高选择性小型化三频带通滤波器,其三个通带的中心频率分别为2.0GHz,3.95GHz和6.35GHz,插入损耗均小于2.5dB,带内回波损耗均优于14dB,实验结果与仿真结果吻合良好.     

具有高带外抑制特性的滤波器天线集成设计

利用滤波器综合设计方法设计了一款新型的具有高带外抑制性的微带滤波器天线。滤波器天线由五个开口谐振环、平行耦合线和倒L 天线组成。设计思路是使用倒L 天线代替滤波器的最后一个谐振器,然后利用平行耦合线等效为导纳变换器将谐振器与天线进行耦合,从而设计出既有滤波性能又有辐射性能的滤波器天线。滤波器天线采用交叉耦合结构,在带外有两个传输零点,大大提高了滤波器天线的带外抑制能力。滤波器天线经过仿真和测试,结果显示其反射系数S11 <-10 dB 的相对带宽为8%(2.37 ~2.57 GHz),带内增益约1.6 dBi,传输零点在带外50 MHz 处,增益下降到-25 dBi,带外整体下降到-20 dBi 以下,带外抑制特性显著。     

X波段Hairpin带通滤波器的设计

Hairpin滤波器在无线通信和卫星通信中应用广泛,基于此根据Hairpin滤波器微带设计的基本理论出发,设计了一款X波段的宽带带通滤波器,中心频率为9 GHz,带宽为2 GHz,插入损耗和带外抑制都达到了指标要求,并且通过ADS和HFSS两个软件的电磁仿真进行了对比和相互验证。     

Low conversion-loss fourth subharmonic mixers incorporating CMRC for millimeter-wave applications

Low conversion-loss millimeter-wave fourth subharmonic (SH) mixer designs are proposed in this paper. A millimeter-wave (35 GHz) fourth SH mixer with four open/shorted stubs is designed and measured. The conversion loss is less than 15 dB within a 2.4-GHz bandwidth. The minimum loss is 11.5 dB at the center frequency. By replacing two of the shunt stubs with a dual-frequency in-line stub consisting of newly developed compact microstrip resonating cells (CMRCs), the performance of the SH mixer is improved significantly. At 35 GHz, the conversion loss of this new fourth SH mixer is as low as 6.1 dB with a 3-dB bandwidth of 6 GHz. The conversion loss in the whole Ka-band (26.5-40 GHz) is less than 16 dB. The proposed fourth SH mixer incorporating with CMRCs provides a low-cost high-performance solution for RF subsystem design.     

Design of 50–70 GHz Planar Wideband Bandpass Filter on Liquid Crystal Polymer Substrate

In this paper, the authors propose a novel and compact 50-70 GHz planar microstrip bandpass filter, possessing sharp-rejection, low insertion-loss and wide-band characteristics, based on Liquid Crystal Polymer (LCP) substrates. The filter is fabricated on LCP substrates by using standard processing technologies. The proposed filter exhibits a return loss level better than 10 dB, an insertion loss of 5 dB and a 3-dB bandwidth of 30%.The measured and simulated results show good agreement, proving that LCPs are potential and very promising materials for flexible millimeter-wave substrate applications.     

Design and performance of millimeter-wave end-coupled bandpass filters

The design and performance of millimeter-wave microstrip/suspended-stripline end-coupled bandpass filters are presented. Filters in Ka-band (26.5 to 40 GHz) and W-band (75 to 110 GHz) using suspended-stripline and microstrip have been designed. Good agreement between the experimental results and those predicted theoretically was observed. Measured passband insertion losses of less than 1 and 0.5 dB have been achieved in W- and Ka-band, respectively. An extremely wideband waveguide-to-microstrip transition with an insertion loss of 0.25 dB over the full W-band is also presented.     

微带抽头线发夹型带通滤波器的设计及优化

介绍一种用ADS( Advanced Design System)软件进行设计和优化微带抽头线发夹型带通滤波器.详细地给出了设计步骤及其各个参数的确定.以一个中心频率为4.8 GHz,带宽为200 MHz的微带带通滤波器的设计及优化为例,给出了仿真结果,并进一步给出了Momentum仿真结果.     

Compact microstrip low-pass filter with sharp rejection

This letter presents a compact multisection sharp-rejection microstrip low-pass filter. Each section consists of a microstrip line section and an interdigital capacitor. The analysis for optimizing the attenuation poles by adjusting the finger number, and the width and length of the microstrip line section, is presented. The cascaded four-section low-pass filter has a return loss of better than 17 dB and an insertion loss of less than 0.7 dB from DC to 1.6 GHz. The rejection is better than 20 dB from 2.1 to 7.5 GHz.     

A 94-GHz aperture-coupled micromachined microstrip antenna

This paper presents an aperture-coupled micromachined microstrip antenna operating at 94 GHz. The design consists of two stacked silicon substrates: (1) the top substrate, which carries the microstrip antenna, is micromachined to improve the radiation performance of the antenna and (2) the bottom substrate, which carries the microstrip feed line and the coupling slot. The measured return loss is -18 dB at 94 GHz for a 10-dB bandwidth of 10%. A maximum efficiency of 58±5% has been measured and the radiation patterns show a measured front-to-back ratio of -10 dB at 94 GHz. The measured mutual coupling is below -20 dB in both E- and H-plane directions due to the integration of small 50-μm silicon beams between the antennas. The micromachined microstrip antenna is an efficient solution to the vertical integration of antenna arrays at millimeter-wave frequencies     

A 60-GHz Millimeter-Wave Bandpass Filter Using 0.18-μm CMOS Technology

This letter presents the design and implementation of a 60-GHz millimeter-wave RF-integrated-circuit-on-chip bandpass filter using a 0.18-mum standard CMOS process. A planar ring resonator structure with dual-transmission zeros was adopted in the design of this CMOS filter. The die size of the chip is 1.148times1.49 mm². The investigations of sensitivity to the insertion loss and the passband bandwidth for different perturbation stub sizes are also studied. The filter has a 3-dB bandwidth of about 12 GHz at the center frequency of 64 GHz. The measured insertion loss of the passband is about 4.9 dB, and the return loss is better than 10 dB within the passband.     

一种基于模式匹配法的窄带Iris波导滤波器设计

提出了一种基于模式匹配法的窄带Iris波导滤波器设计方法,通过引入Matlab优化使滤波器设计周期缩短了约1/3。设计的窄带滤波器相对带宽小于3%,且较好的克服了毫米波频段滤波器高频端带外抑制较差的难题。测试结果表明,该带通滤波器插入损耗小于0.8 dB,驻波比小于1.2,中心频率34.86 GHz,带外抑制52 dB@36.5 GHz,已被成功应用于某毫米波雷达通信系统中。     

一种毫米波调谐微带滤波器的研制

该文基于金丝键合工艺和薄膜工艺,实现了一种低插损、小型化毫米波调谐微带滤波器。首先提出了一种加载矩形孔的半波长开路可调谐振器,通过在不同矩形孔上键合金丝来改变谐振器的等效电感值,从而改变谐振频率。然后利用所提出的可调谐振器实现了一种Ka频段五阶调谐带通滤波器,通过改变键合金丝状态来调谐频率,实现仿真和实测结果之间的偏差修正,解决了在毫米波频段由于介电常数批次性差异以及加工误差等因素造成的窄带滤波器频率偏移的问题。为了验证其可行性,对五阶调谐微带滤波器进行仿真、优化、加工及测试。结果表明,该滤波器的通带可调范围为35.35~35.95 GHz,插入损耗小于4.6 dB,能够实现所需通带。