Preparation of high-porosity Al2O3 ceramic foams via selective laser sintering of Al2O3 poly-hollow microspheres

In this paper, high-porosity Al₂O₃ ceramic foams called Al₂O₃ PHM ceramics were fabricated through selective laser sintering (SLS) via Al₂O₃ poly-hollow microspheres (Al₂O₃ PHMs). SLS parameters were optimized by an orthogonal experiment as to be laser power = 6 W, scanning speed = 1800 mm/s, and scanning space = 0.15 mm. The effect of sintering temperature on microstructure, shrinkage, porosity, phase composition, mechanical properties and pore size distribution of Al₂O₃ PHM ceramics were investigated. When sintering temperature increased, Al₂O₃ PHM ceramics contained only Al₂O₃ phase and were gradually densified. With the raise of sintering temperature, the porosity of Al₂O₃ PHM ceramics decreased gradually from 77.09% to 72.41%, but shrinkage in H direction and compressive strength of Al₂O₃ PHM ceramics increased from 6.63% and 0.18 MPa to 13.10% and 0.72 MPa, respectively. Sintering temperature had little effect on pore size distribution of Al₂O₃ PHM ceramics, which only declined from 24.2 to 21.4 μm with the increase of sintering temperature from 1600 to 1650 °C. This method can not only directly prepare ceramic foams with complex shapes, but also control properties of ceramic foams. It provides a simple preparation method for many kinds of ceramic foams with complex structure and high porosity by using PHMs with different composition.     

Anisotropic properties of textured h-BN matrix ceramics prepared using 3Y2O3-5Al2O3(-4MgO) as sintering additives

Textured hexagonal boron nitride (h-BN) matrix composite ceramics were prepared by hot pressing using 3Y₂O₃-5Al₂O₃ (mole ratio of 3:5) and 3Y₂O₃-5Al₂O₃-4MgO (mole ratio of 3:5:4) as liquid phase sintering additives, respectively. During the sintering process with liquid phase environments, platelike h-BN grains were rotated to be perpendicular to the sintering pressure, forming the preferred orientation with the c-axis parallel to the sintering pressure. Both h-BN matrix ceramic specimens show significant texture microstructures and anisotropic mechanical and thermal properties. The h-BN matrix ceramics prepared with 3Y₂O₃-5Al₂O₃-4MgO possess higher texture degree and better mechanical properties. While the anisotropy of thermal conductivities of that prepared with 3Y₂O₃-5Al₂O₃ is more significant. The phase compositions and degree of grain orientation are the key factors that affect their anisotropic properties.     

AC Impedance Spectroscopy of CaF2‐doped AlN Ceramics

The electrical conductivity of CaF₂‐doped aluminum nitride (AlN) ceramics was characterized at high temperatures, up to 500°C, by AC impedance spectroscopy. High thermal conductive CaF₂‐doped AlN ceramics were sintered with a second additive, Al₂O₃, added to control the electrical conductivity. The effects of calcium fluoride (CaF₂) on microstructure and related electrical conductivity of AlN ceramics were examined. Investigation into the microstructure of specimens by TEM analysis showed that AlN ceramics sintered with only CaF₂ additive have no secondary phases at grain boundaries. Addition of Al₂O₃ caused the formation of amorphous phases at grain boundaries. Addition of Al₂O₃ to CaF₂‐doped AlN ceramics at temperatures 200°C–500°C revealed a variation in electrical resistivity that was four orders of magnitude larger than for the specimen without Al₂O_3. The amorphous phase at the grain boundary greatly increases the electrical resistivity of AlN ceramics without causing a significant deterioration of thermal conductivity.     

Preparation of porous Al2O3 ceramics with enhanced properties by SLS using Al2O3 poly-hollow microspheres (PHMs) coated with CaSiO3 sintering additive

The mechanical properties of porous ceramics prepared by poly-hollow microspheres (PHMs) is usually low because of the weak bonding between different ceramic PHMs. In this paper, CaSiO₃ were coated to the surface of Al₂O₃ PHMs through co-precipitation method as sintering additive to improve the properties of Al₂O₃ poly-hollow microsphere ceramics (Al₂O₃ PHM ceramics). The influence of different amount of CaCl₂ solution on properties of the Al₂O₃ PHM ceramics such as phase composition, microstructure, porosity and mechanical properties were studied. The porosity of the Al₂O₃ PHM ceramics decreased from 77.03% to 68.16% with the increase of CaCl₂ solution amount, while compressive strength increased 29 times from 0.29 MPa to 8.39 MPa. The addition of the CaSiO₃ could decrease the sintering temperature of Al₂O₃ PHM ceramics and significantly improve the mechanical properties of Al₂O₃ PHM ceramics, which is beneficial for preparing highly porous Al₂O₃ PHM ceramics with high mechanical properties and complex shapes.     

SiAlON–Al2O3 ceramics as potential biomaterials

When used as implants, Al₂O₃ is unable of directly achieving good chemical bonding with soft and hard tissues. To overcome this problem, SiAlON–Al₂O₃ ceramics were prepared in this study by direct nitridation. Phase composition, porosity, bulk density, and compression strengths were examined, and biological properties were evaluated by cell culture on ceramic surface. Major phase of SiAlON–Al₂O₃ ceramics was identified as Si₄Al₂O₂N₆, formed by reaction of Si, Al and Al₂O₃ under nitrogen atmosphere at high temperature. As Al₂O₃ content increased, porosity and compressive strength decreased. Therefore, Si₄Al₂O₂N₆ phase could improve sintering, leading to formation of composites with better properties. The porosity and compression strength were found suitable for requirement of biomaterials. Cell culture experiments showed that cells could proliferate and survival well on ceramic surface, indicating good biocompatibility of Si₄Al₂O₂N₆ phase in SiAlON–Al₂O₃ ceramics. Overall, these data look promising and might provide novel strategies for development of future SiAlON–Al₂O₃ bioceramics.     

Effect of Y2O3 on the physical properties and biocompatibility of β–SiAlON ceramics

To investigate the effects of Y₂O₃ on the physical properties and biocompatibility of β–SiAlON ceramics, β–SiAlON ceramics were prepared with Al, Si, and α–Al₂O₃ powders using a direct nitriding technique. As a sintering additive, Y₂O₃ helps lower the sintering temperature and forms β–SiAlON ceramics. In this study, the physical and biological properties of the prepared ceramics were investigated to evaluate their use as bone-repairing material. Experiments revealed that the main crystal composition of the sample was Si₄Al₂O₂N₆, containing small amount of additional phases Y₃Al₅O₁₂ with increasing content of Y₂O₃. The porosity and compressive strength initially decrease and then increase to their initial values, whereas the bulk density exhibits the opposite trend with an increased proportion of Y₂O₃. The proliferation of osteoblastic and angiogenic cells demonstrates that β–SiAlON and Y₃Al₅O₁₂ have good biocompatibility; however, the sample porosity has a slight effect on the cell proliferation rate. This implies that in human tissues, bone-repairing speed can be adjusted by modifying the sample porosity or material surface roughness. Therefore, Y₂O₃ can be added to β–SiAlON ceramics to regulate their microstructure, physical properties, and biological properties for tissue engineering applications.     

CaO–SiO2–Al2O3–Y2O3 glasses as model grain boundary phases for Si3N4 ceramics

The glasses with compositions derived from the eutectic composition [37.78 (Y₃Al₅O₁₂)·62.22 (SiO₂)] of the quasi-binary glass system (Y₃Al₅O₁₂)-(SiO₂) with addition of up to 20 mol.% CaO were investigated as model grain boundary phases for Si₃N₄ ceramics. The influence of CaO as model impurity on the physical properties of the glass (density, thermal expansion) and on the crystallisation behaviour was studied. Although the initial composition of the basic glass was that of yttrium-aluminium garnet (Y₃Al₅O₁₂–YAG), no crystalline YAG was detected. Apart from yttrium disilicate (Y₂Si₂O₇), anorthite (CaAl₂Si₂O₈), tricalcium aluminate (Ca₃Al₂O₆), and calcium yttrium oxide silicate (Ca₄Y₆O(SiO₄)₆), a new phase was detected, not found in the powder diffraction file (PDF) database. Cavities were formed within the devitrified glass due to the volume contraction after crystallisation. Possible implications for the mechanical properties of Si₃N₄ ceramics sintered with addition of Y₂O₃–Al₂O₃ are discussed in terms of the observed compositional dependences of the physical properties of CaO–Y₂O₃–Al₂O₃–SiO₂ glasses.     

Ultrafast preparation of Al2O3–ZrO2 multiphase ceramics with eutectic morphology via flash sintering

Herein, Al₂O₃–ZrO₂ multiphase ceramics with a eutectic molar ratio were prepared using the flash sintering technique at 1200 °C in 2 min. The samples were divided into two regions according to the microscopic morphology: multiphase ceramics zone and eutectic ceramics zone. The multiphase ceramics zone uniformly distributed irregular Al₂O₃ and ZrO₂ phases. The eutectic zone presented typical eutectic morphology, where different morphologies of ZrO₂ was uniformly embedded in the Al₂O₃ matrix, mainly showing fine lamellar, rod-like and irregular network morphology. Overall, flash sintering is a promising route to prepare high-performance multiphase ceramics.     

The Effect of Sesquioxides of 3d-Transition Elements on the Strength of Synthetic Mullite and Mullite-Based Materials

Mullite synthesized from alumina and silica with the sesquioxide of a 3d-transition metal added (Me = Sc, Ti, V, Cr, Mn, and Fe) is capable of forming solid solutions of composition Al_6–x Me _xSi₂O₁₃. It is shown, using data obtained by methods of x-ray phase analysis, electron paramagnetic resonance, infrared spectroscopy and magnetic susceptibility, that the aluminum atoms located at octahedral positions of the mullite lattice can be isomorphously replaced by Me metals. The effect of this replacement on the strength of mullite and mullite-based ceramics is considered.     

A novel method for the fabrication of porous calcium hexaluminate (CA6) ceramics using pre-fired CaO/Al2O3 pellets as calcia source

Herein, porous calcium hexaluminate ceramics that contain pores exhibiting multiple morphologies were fabricated via in situ reaction sintering using α-Al₂O₃ powders and pre-fired CaO/Al₂O₃ pellets. The results indicated that the composition of the pre-fired CaO/Al₂O₃ pellets significantly affected the pore morphology, reaction-diffusion mechanisms, sintering behaviour and properties of the porous CA₆ ceramics. For the specimens containing low CaO/Al₂O₃-ratio (0.37) pellets, the main reaction occurred by solid state diffusion, i.e. ion diffusion through the solid reactant phase, which resulted in a slow process and low CA₆ formation rate at an elevated sintering temperature. With higher CaO/Al₂O₃-ratio (0.57) pellets, large-sized pores were observed because of transient liquid phase diffusion during the sintering process. The transient liquid phase diffusion effect increased the porosity of the porous ceramics and promoted the formation of a large number of plate-like CA₆ grains in the walls of the pores, enhancing their mechanical properties and high-temperature performance. The porous CA₆ ceramics containing high CaO/Al₂O₃-ratio (0.57) pellets sintered at 1700 °C exhibited high open porosity (55.88%), low thermal conductivity and excellent high-temperature performance.     

0.73ZrTi2O6–0.27MgNb2O6 microwave dielectric ceramics modified by Al2O3 addition

0.73ZrTi₂O₆–0.27MgNb₂O₆ ceramics with various Al₂O₃ contents (0‐2.0 wt%) were prepared by conventional ceramic route. The effects of Al₂O₃ on the phase composition, microstructure, conductivity, and microwave dielectric properties were systematically investigated. The coexistence of a disordered α–PbO₂‐type phase and a rutile second phase was found in all compact ceramics with low Al₂O₃ contents (x = 0, 0.5, and 1.0 wt%), while a corundum phase was detected when Al₂O₃ additive increased to 1.5 and 2.0 wt% based on X‐ray diffraction results. With the addition of Al₂O₃, the decreased grain size of the matrix phase was observed using field‐emission scanning electron microscope, accompanied with increased resistivity and band‐gap energy. Additionally, Al₂O₃ additives efficiently improved the quality factor of the ceramics. After sintering at 1360°C for 3 hours, the ceramic with 1.0 wt% Al₂O₃ exhibited excellent microwave dielectric properties: a dielectric constant of 43.8, a quality factor of 33 900 GHz (at 6.6 GHz), and a near‐zero temperature coefficient of resonant frequency (3.1 ppm/^°C).     

Preparation,microstructures, and mechanical properties of directionally solidified Al2O3/Lu3Al5O12 eutectic ceramics

Al₂O₃/Lu₃Al₅O₁₂ (LuAG) directionally solidified eutectic (DSE) ceramics with two solidification rates were prepared utilizing optical floating zone (OFZ) technique. The microstructures (eutectic morphology, preferred growth direction and interface orientation) of Al₂O₃/LuAG were characterized, and the mechanical properties (Vickers hardness and fracture toughness) were compared with those of Al₂O₃/REAG (RE = Y, Er, and Yb). Results show that Al₂O₃/LuAG with solidification rate of 30 mm/h has established preferred growth direction in both Al₂O₃ and LuAG phases with cellular eutectic structures. While Al₂O₃/LuAG with solidification rate of 10 mm/h only shows preferred growth direction in Al₂O₃ phase and presents degenerate irregular eutectic microstructures. Besides, Al₂O₃/LuAG exhibits higher hardness compared with Al₂O₃/REAG (RE = Y, Er, and Yb). In addition, a special attention is focused on the relations among rare earth ionic radius, eutectic microstructures, and mechanical properties of these DSE ceramics. It is demonstrated that a smaller rare earth ionic radius could lead to larger eutectic interspacing as well as higher Vickers hardness of DSE Al₂O₃/REAG, revealing the possibility and feasibility of microstructure control and mechanical properties optimization for DSE Al₂O₃/REAG ceramics by tailoring the rare earth elements.     

The effect of rare earth oxides on the pressureless liquid phase sintering of α-SiC

Silicon carbide (SiC) ceramics have been fabricated by pressureless liquid phase sintering with Al₂O₃ and rare-earth oxides (Lu₂O₃, Er₂O₃ and CeO₂) as sintering additives. The effect was investigated of the different types of rare earth oxides on the mechanical property, thermal conductivity and microstructure of pressureless liquid phase sintered SiC ceramics. The room temperature mechanical properties of the ceramics were affected by the type of rare earth oxides. The high temperature performances of the ceramics were influenced by the triple junction grain boundary phases. With well crystallized triple junction grain boundary phase, the SiC ceramic with Al₂O₃–Lu₂O₃ as sintering additive showed good high temperature (1300 °C) performance. With clean SiC grain boundary, the SiC ceramic with Al₂O₃–CeO₂ as sintering additive showed good room temperature thermal conductivity. By using appropriate rare earth oxide, targeted tailoring of the demanding properties of pressureless liquid phase sintered SiC ceramics can be achieved.     

Microstructure of the directionally solidified ternary eutectic ceramic Al2O3/MgAl2O4/ZrO2

The directionally solidified Al₂O₃/MgAl₂O₄/ZrO₂ ternary eutectic ceramic was prepared via induction heating zone melting. Smooth Al₂O₃/MgAl₂O₄/ZrO₂ eutectic ceramic rods with diameters of 10 mm were successfully obtained. The results demonstrate that the eutectic rods consist of Al₂O₃, MgAl₂O₄ and ZrO₂ phases. In the eutectic microstructure, the MgAl₂O₄ and Al₂O₃ phases form the matrix, the ZrO₂ phase with a fibre or shuttle shape is embedded in the matrix, and a quasi-regular eutectic microstructure formed, presenting a typical in situ composite pattern. During the eutectic growth, the ZrO₂ phase grew on non-faceted phases ahead of the matrix growing on the faceted phase. The hardness and fracture toughness of the eutectic ceramics reached 12 GPa and 6.1 MPa·m ^1/2, respectively, i.e., two times and 1.7 times the values of the pre-sintered ceramic, respectively. In addition, the ZrO₂ phase in the matrix reinforced the matrix, acting as crystal whiskers to reinforce the sintered ceramic.     

Investigation on the anti-reduction mechanism of Ti4+ in high dielectric constant system Ca0.9La0.067TiO3 by doping with Al2O3

Ca_0.9La_0.067TiO₃ (abbreviated as CLT) ceramics doped with different amount of Al₂O₃ were prepared via the solid state reaction method. The anti-reduction mechanism of Ti⁴⁺ in CLT ceramics was carefully investigated. X-ray diffraction (XRD) was used to analyze the phase composition and lattice structure. Meanwhile, the Rietveld method was taken to calculate the lattice parameters. X-ray photoelectron spectroscopy (XPS) was employed to study the valence variation of Ti ions in CLT ceramics without and with Al₂O₃. The results showed that Al³⁺ substituted for Ti⁴⁺ to form solid solution and the solid solubility limit of Al³⁺ is near 1.11 mol%. Furthermore, the reduction of Ti⁴⁺ in CLT ceramics was restrained by acceptor doping process and the Q × f values of CLT ceramics were improved significantly. The CLT ceramic doped with 1.11 mol% Al₂O₃ exhibited good microwave dielectric properties: ε_r = 141, Q × f = 6848 GHz, τ_f = 576 ppm/°C.     

Sol–gel synthesis and investigation of un-doped and Ce-doped strontium aluminates

The preparation of various strontium aluminates including SrAl₂O₄ (SrO–Al₂O₃), Sr₃Al₂O₆ (3SrO–Al₂O₃), and Sr₄Al₄O₁₀ (4SrO–2Al₂O₃) was performed by using a simple aqueous sol–gel processing. The formation of strontium aluminate phases was investigated as a function of temperature in the range of 700–1200 °C. The obtained compounds were doped with cerium in the concentration range of 0.25–3.00 mol%. The sol–gel derived samples were characterized by X-ray powder diffraction (XRD) analysis, infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and UV–Vis diffuse reflectance spectroscopy. It was demonstrated that optical properties of obtained phosphor materials slightly depend on the nature, crystal structure and phase purity of the strontium aluminate matrix.     

Microstructure and microwave dielectric properties of Al2O3 added Li2ZnTi3O8 ceramics

Recently, the rapid development of advanced communication systems increasingly strongly demands high-performance microwave dielectric ceramics in microwave circuits. Among them, Li₂ZnTi₃O₈ ceramics have been one of the most widely investigated species, due to its high quality factor, moderate firing conditions and low cost. However, the dielectric constants of the already reported Li₂ZnTi₃O₈ ceramics are fixed in a narrow range, limiting their wider applications. To adjust the dielectric constant of the Li₂ZnTi₃O₈ based ceramics, in this work Li₂ZnTi₃O₈ ceramics added with different amounts of Al₂O₃ (0–8?wt%) were prepared by conventional solid-state reaction. The microstructure and microwave dielectric properties of the samples were investigated. Due to the addition of Al₂O₃, the sintering temperature of the ceramics would be increased somewhat. Some Al³⁺ ions could substitute for Ti⁴⁺ ions in Li₂ZnTi₃O₈, and the added Al₂O₃ would react with ZnO to produce a ZnAl₂O₄ phase accompanying with the formation of TiO₂ phase, which would inhibit the growth of Li₂ZnTi₃O₈ grains. The dielectric constant of the finally obtained ceramics would be reduced from 26.2 to 17.9, although the quality factors of the obtained ceramics would decrease somewhat and the temperature coefficient of resonant frequency would deviate further from zero.     

Controllable Preparation of Al2O3‐MgO·Al2O3‐CaO·6Al2O3 (AMC) Composite with Improved Slag Penetration Resistance

Compact Al₂O₃‐MgO·Al₂O₃‐CaO·6Al₂O₃ (AMC) composite was obtained by melting technology using industrial alumina, light‐burned magnesia, and quick lime as raw materials based on the Al₂O₃‐MgO‐CaO ternary phase diagram. The results show that the phases of MgO·Al₂O₃ and Al₂O₃ are formed as the main framework with plate‐like CaO·6Al₂O₃ crystals mainly discontinuously embedded in MgO·Al₂O₃. The bulk density of AMC composite is up to 3.42 g/cm³, equivalent to 90.5% of the theoretical density. The synthesized compact AMC composite in the work also exhibits better slag penetration resistance than the castable based on tabular corundum due to the formation of liquid phase.     

Pressureless sintered Al4SiC4 ceramics with Y2O3 addition

Highly densified Al₄SiC₄ ceramics with a relative density of 96.1% were prepared by pressureless sintering using 2 wt% Y₂O₃ as additives. The densification mechanism, phase composition, microstructures and mechanical properties of Al₄SiC₄ ceramics were investigated. Y₂O₃ in-situ reacted with the oxygen impurities in Al₄SiC₄ powder to form a yttrium aluminate liquid phase during sintering, which promoted the densification and anisotropic grain growth. The final Al₄SiC₄ ceramics were composed of equiaxed grains and columnar grains, and presented a bimodal grain distribution. The mechanical properties of the pressureless sintered Al₄SiC₄ ceramics were better than those reported for hot pressed Al₄SiC₄, including a flexural strength of 369 ± 24 MPa, fracture toughness of 4.8 ± 0.1 MPa m^1/2 and Vickers hardness of 11.3 ± 0.2 GPa. Pressureless sintering of Al₄SiC₄ ceramics is of great significance for the development and practical application of Al₄SiC₄ ceramic parts, especially with big size and complex shape.